Search Documents

By H. Huang, H. M. Chen, W. B. Xie

Cu-0.8Cr-0.1Zr alloy were prepared by atmospheric melting. the microstructure and properties of the CuCrZr alloy after first cold rolled, solid solution, second cold rolled and aging treatment were analyzed by using optical microscope, electrical conductivity analysis and Vickers hardness tester. The results show that with the increase of the first cold rolled deformation, the grain breakage becomes more serious, and the cold hardening becomes more obvious and the hardness increases. The conductivity and peak hardness of the first cold rolled (reduction of 30% and 60%) alloys after solution, secondary cold rolled and aging treatment reaches 81 %IACS and 187 HV, respectively. However, the conductivity in the CuCrZr alloy with a higher rolling degree (reduction of 90%) after solution, secondary cold rolling and aging treatment is significantly higher, and the conductivity and peak hardness is 85.8 %IACS and 178 HV, respectively. INTRODUCTION CuCrZr alloy has been widely used in domestic industry for its excellent comprehensive properties such as high strength and high conductivity, especially in the contact wire and lead frame of high-speed railway (Sun, Tao, & Lu, 2015; Mishnev, Shakhova, Belyakov, & Kaibyshev, 2015; Zhang et al., 2016; Fu et al., 2017). In recent years, a lot of research has been done on how to improve the strength and conductivity of CuCrZr alloy. However, the high strength and high conductivity of copper alloys are contradictory characteristics. On the one hand, the addition of alloying elements is conducive to solution strengthening and aging strengthening; on the other hand, too much alloying elements in copper alloys cause defects in the lattice of copper matrix, resulting in a serious decline in the conductivity of copper alloys (Martienssen & Walirmont, 2005). How to obtain high strength and high conductivity at the same time is the main problem. At present, the main research methods are adding microalloying elements, thermomechanical treatment and severe plastic deformation to study the electrical conductivity and mechanical properties of CuCrZr alloys. For example, Xie et al. (2011) added trace Ag to the Cu-0.26 wt%Cr-0.08 wt%Zr alloy, and the size of precipitated phase Cr and Cu4Zr became smaller and the mechanical properties of the alloy were improved. Su, Dong, Liu, Li, & Kang (2004) found that the addition of trace Mg in CuCrZr alloy inhibits the growth of precipitated phase and reduces the internal stress around the precipitated phase. At the same time, the size of precipitated phase becomes smaller and the peak aging strength of the alloy is improved. Pang et al. (2013) found that adding trace Ni and Si to the CuCrZr alloy could improve the peak hardness, softening resistance and precipitation morphology of the alloy. Experiments shows that the grain size was significantly refined by equal channel angular extrusion combined with aging treatment, while the strength of the alloy was increased, and the electrical conductivity of the alloy did not decrease (Vinogradov, Patlan, Suzuki, Kitagawa, & Kopylov, 2002; Saray, 2016); Kermajani, Raygan, Hanayi, & Ghaffari (2013) showed that the strength of CuCrZr alloy can be improved by rolling at 500 °C. After 150 minutes of aging treatment, the strength and conductivity of the material increased to 431 MPa and 81 %IACS, respectively. Takata, Ohtake, Kita, Kitagawa, and Tsuji (2009) noted that the strain hardening, uniform elongation and tensile strength of the nano-precipitates produced by the mechanical heat treatment process can be notable enhanced. The mechanical and electrical properties of CuCrZr alloy can be improved by combining large plastic deformation with aging treatment in the test process (Gao, Huttunen-Saarivirta, Tiainen, & Hemmila, 2003; Huang et al., 2003; Xia et al., 2012; Zel’dovich et al., 2014).

Jan 1, 2019

By L. Dubourg, H. Habibi, D. Rasmussen

The combination of laser welding with Gas Metal Arc Welding (GMA W) forms the hybrid laser-OMA W welding. This process is an attractive tool with a high potential in welding lightweight structures, especially for aluminum alloys. For five years, this technology has increasingly attracted interest in both, industry (aeronautics, automobile, metal industries producing large structures) and academia (universities and research centers). Hybrid laser-OMA W welding process is generally accepted for its robustness, efficiency and flexibility. Coupling of a deep-penetrating laser beam with the heat and molten metal feeding of GMA W significantly expands the original welding application range of lasers. Its main advantages compared to the two individual components are deep and stable weld penetration, gap-bridging ability improvement, low distortion and easy filler metal addition. Hybrid welding allows a much wider groove tolerance compared to laser welding, especially for aluminum welding. Moreover, the reduction in distortion decreases the post-welding rectification needed and makes the assembly easier. In addition, if metallurgical factors are critical, the weld composition can be balanced with filler metal, decreasing the hot cracking susceptibility of some aluminum alloys. The combination of these two welding processes can also improve the weld bead shape quality (including the elimination of undercut), possibly reduce the porosity and increase the welding speed. This article reviews the recent works about the laser-OMA W hybrid welding of aluminum alloys. After a brief presentation on the interaction mechanisms between a laser beam and an electric arc, the paper depicts the typical welding parameters and experimental methods along with their characteristics.

Jan 1, 2006

By Jian Deng

Rockbursts are sudden and violent failure of rocks in deep and/or high stress mines, which may destroy the excavation space and cause an accident or even the death of mining workers. This study is motivated by the pervasiveness of rockbursts all round the world. It has been found that rockbursts are often stimulated by dynamic fluctuation which is generated by mining operations or other sources of vibrations, such as blasting in adjacent stopes. This paper attempts to investigate the dynamically stimulating mechanism of pillar rockbursts in hard rock mines from an innovative point of view. Rockbursts are classified into triggered rockbursts and induced rockbursts in accordance with the magnitude of the stimulation force. Triggered rockbursts occur only when a small fraction of stress changes associated with rockbursts is accounted for by the causative excavation, whereas induced rockbursts happen where the causative factor is responsible for most of the stress changes required to produce the rockburst. By considering rockbursts as a dynamic instability problem of structures, rigorous mathematical models are set up for triggered rockbursts and induced rockbursts, respectively. By using the method of averaging and the method of eigenvalue problems, the boundaries of rockburst occurrence of a pillar are obtained for these two rockbursts. A new explanation of the failure mode of fretting or necking of pillars is given, the perturbation effect for pillar rockbursts is found, and the parametric resonance mechanism of pillar rockbursts is revealed. The quantitative relation between blasting parameters and pillar rockbursts obtained can be directly used to control the rockbursts. Contrary to conventional methods where only rock materials or rock specimen were used to study rockbursts, this investigation attaches more attention on the structural effect on rockbursts, which have strong potential applications in deep mining.

Jan 1, 2015

By S. W. Henley

"Shaft sinking design is typically driven by what has been successful in the past and the availability of sinking plant. This document considers a project where the sinking design and methodology is unconstrained by conventional thinking and removed from the commonly held belief that a sinking methodology should be developed from available winding plant. Schedule was a key driver for the Project and led to an alternative sinking design that aimed to optimise sinking advance rates by specifying new winders that compliment known sinking plant while providing improved safety, redundancy and flexibility within each part of the sinking cycle. KEYWORDS Consistent, Efficient, Flexible, Improved, Innovative, Optimise, Redundancy, Safety, Schedule INTRODUCTION The project is remotely located in the South Gobi region of Mongolia on a brownfield site and the scope of work included the concurrent blind sinking and concrete lining of two (2) ventilation shafts to an approximate depth of 1,150 m at a finished diameter of 10 m and 11 m respectively. All sinking and lining operations to be completed as in-line activities, (no lining whilst other activities are undertaken). The project was schedule driven with a completion date set for the first quarter (calendar) of 2021 and there were no restrictions imposed on the successful Contractor with respect to their equipment selection. Existing sinking plant already onsite from three previous shaft sinking operations would be made available to the Contractor if required on an as is where is basis Sustained advance rates in excess of 2.4 m per day would be required in order to achieve the completion milestone, therefore the design would have to include contingency and demanded flexibility to account for equipment down time. Previous shafts that had been sunk onsite have utilised a single double drum kibble (bucket) winder (hoist) with a single excavator loading on the shaft floor into a large capacity kibble (bucket). DESIGN Mucking The sinking design centred on the mucking cycle given that this is traditionally the most restrictive part of the sinking cycle and typically accounts for one third of the overall sinking cycle. The Vertical Shaft Mucker (VSM) and/or diesel excavator are commonly used plant for shaft sinking that were under consideration. The use of Cactus Grabs was not considered given the higher risk associated with grab ropes and hoist failures."

Jan 1, 2019

By W. R. Horn

"WHAT I PROPOSE TO DO is to review or report very briefly and generally on the most important subject areas of environmental concern within the mining industry and to indicate the progress being made. First, however, it seems to me both appropriate and necessary to refer to what I said in an address to the CIM Annual Western Meeting, in November 1971, in Vancouver. At that time, I tried to convey: that the awareness and alertness of this far-flung and diversified industry was sharply on the up-swing; that the knowledge of helpful technology for the abatement of pollution by water and solids was significantly increasing; that most mines were doing something about it; that many had already achieved a recycling of process water to a really significant extent; that progress was being made - though not without considerable difficulty - on the large-scale neutralization and subsequent chemical treatment of acid- and metals-bearing waters; that increasing work was being done by individual mining companies on methods for the vegetation of completed tailings impoundments; and that it had been possible to develop a meaningful estimate of the amount of money to be spent by the industry on environmental control measures during the period 1971-75 (as much as $500,- 000,000 ) . Reference was also made at that time to the constructive work in hand toward the fixation, elimination or dispersion of sulphur from smelters and to the considerable attention which was being given by the indust(y itself toward in-plant problems, e.g., dust and noise. Finally, note was taken of the fact that the inclusion of environmental control costs in the pre-operational financial provisions of new mining operations is now established practice."

Jan 1, 1973

By E. C. Sanford

A laboratory-scale batch extraction unit and operating procedure for studying the hot-water separation of bitumen from Athabasca tar sands are described. The extractor evolved from earlier units and has been in use by Syncrude Research for the past 10 years. By using a unit such as this, it is possible to study tar sand feed quality and the effects of chemicals on the hot-water extraction process, while process variables are held constant. Data are presented to demonstrate the importance of surfactants to the process and the interrelated role of inorganic bases and surfactants.

Jan 1, 1979

By W. R. Smith

Introduction No commercial deposits of silica sand are known to occur in British Columbia, so all requirements for foundry and other uses must be imported. During the war, nearly 5,000 tons per year were used, all originating in Illinois and delivered to local consumers for about $12.00 per ton. Present requirements are somewhat less, but the cost is still of the same order. The relatively high cost of silica sand in British Columbia is not only a serious item for present consumers, but might be a deterrent to the establishment of a glass industry, should this be contemplated at any time. The present investigation was undertaken in an attempt to provide a cheaper source of silica sand within the Province. In 1936, a large number of beach and bank sand deposits in the lower coastal region of British Columbia were examined by the British Columbia Department of Mines, and samples were analyzed chemically and mineralogically. The deposits over the whole area proved remarkably uniform in mineral composition, consisting essentially of quartz, feldspar, ferromagnesian minerals, rock fragments, and various accessory minerals, and differing only in the relative proportions of the various constituents. In no case did the quartz content of any sand exceed about 40 percent and the average was of the order of 20 to 30 percent.

Jan 1, 1947

By T. Crivits

"Freeze lining technologies are used industrially to protect the integrity of furnace walls in pyrometallurgical reactors. This is achieved by solidifying a protective layer of slag on the inner furnace wall. In the current study, laboratory experiments have been undertaken to produce freeze linings in ‘Cu2232 O’-‘FeO’-MgO-SiO slags under controlled conditions using an air-cooled probe technique. Whilst most thermal models of freeze linings have assumed the freeze lining-bath interface to be at the liquidus temperature of the bulk bath and to be planar in geometry, the current research has demonstrated that this is not the case. Experiments undertaken using this high-temperature slag system have shown the interface at steady state conditions to be at subliquidus temperatures. The solid phases present at the interface do not include the primary phase and the interface is non-planar. The study indicates the need for improved understanding of the fundamentals of freeze lining formation, and of the influence of system properties and process parameters"

Jan 1, 2015

By Robert E. Wood

Engineers have known for some time that the efficiency of filtering iron ore concentrate slurry can be significantly improved by pre-heating the slurry ahead of the filters. However, heating such large quantities of dense slurry by conventional means has proven to be inefficient and high-maintenance. Recently though, submerged combustion was considered by Altos Hornos de Mexico SA (AHMSA), an integrated steel producer in the state of Coahuila, Mexico, as a means of pre-heating their iron ore concentrate. The company toured many iron ore facilities in Brasil and Labrador, reviewing their heating processes, and concluded that submerged combustion could provide a competitive advantage through operational efficiency and lower capital cost than steam boilers. Inproheat was retained by the company to design and manufacture a SubCom slurry heating system to heat 403 m3/h of iron ore concentrate slurry from 25°C to 60°C. The 60GJ/h SubCom system consists of five natural gas combustion chambers mounted in an iron ore concentrate storage tank. The system features a heat recovery unit whereby the exhaust gases are used to preheat the incoming slurry stream, giving the system an overall thermal efficiency of 95%. As a result, the steel company expects to realise significant improvements in filtering efficiency which will enable them to increase the capacity of their pelletising plant without installing additional filters.

May 1, 2010

By J. F. Henderson

THIS paper relates to an area of more than 5,000 square miles in the Northwest Territories extending north from Great Slave lake and including-the Yellowknife, Beaulieu River and Gordon lake areas. Within the last three years much interest in the area has been created by the discovery of remarkably rich gold-bearing veins and the realization that thousands of square miles of unprospected ground are underlain by rocks like those in which the veins have been found. Probably there were more prospectors in this area in 1938 than in any other part of Canada. The area lies 650 miles north of Edmonton, and 425 miles north of the terminus of the Northern Alberta railway at Waterways, Alberta. The Athabaska and Slave rivers provide an excellent water route from Waterways to Great Slave lake for large oil and wood burning boats and barges which operate from the latter part of May to October. The only portage is around a 16-mile stretch of rapids on the Slave river between Fort Fitzgerald and Fort Smith. The town of Yellowknife, on the north side of Great Slave lake, has sprung into existence during the past year and is the centre for distribution of supplies for the Yellowknife-Beaulieu region. The Con-Rycon and Negus gold mines, which came into production in September, 1938, and February, 1939, respectively, lie about two miles south of the townsite. Excellent airplane service is available from Edmonton to Yellowknife and from Yellowknife to all parts of the area. The prospector and mining operator have come to rely almost entirely on the airplane for supplies and for the transportation of personnel, camp equipment, and canoes from Yellowknife to localities selected for intensive prospecting.

Jan 1, 1939

By M. Sengupta

International trade in minerals plays a very important role in the economic growth of many nations. Several less developed countries a1•e heavily dependent on their mineral exports for earning foreign exchange, which is needed for industrialization. Mineral exporting nations experience many problems in international mineral markets; the most important are tariff barriers, deteriorating terms of trade, instability in metal prices, etc. The formation of international mineral cartels to raise prices can be successful only to a limited extent and only for a short period of time.

Jan 1, 1976

By X. Shi

Magnesium, the lightest structural metal, has not yet been considered as a serious contestant for automotive use due to its weaknesses in corrosion. Electroless nickel-boron alloys are well known for their corrosion resistance and hardness. An electroless nickel-boron layer was successfully deposited first on the chemical conversion pre-treated AZ31 alloy and also on the Ni-P coating which was deposited on the conversion coating. The electroless bath contained nickel sulphate and dimethylamine borane (DMAB) as main salts and the samples were activated by a 5 g/L AgNO3 solution before the electroless plating process. The presence of the conversion coating between the nickel coating and the AZ31 substrate acted as a barrier and prevented corrosion of the alloy. The morphology of the nickel-boron layer was studied using SEM. The crystal structure and the composition were examined by EDS and the hardness was measured. The corrosion behaviour of the nickel-boron layer deposited on the conversion coating and on the Ni-P coating was studied using potentiodynamic polarization in a 0.5M NaC1 solution. A saturated standard calomel electrode was used as a reference electrode. The results show that the nickel-boron coatings had a significantly better corrosion resistance than the AZ31.

Jan 1, 2006

By J. Kolacz

"A new sensor based sorting system has been developed, providing a possibility for laboratory scale testing and further scale-up of the separation results to the industrial operation. The new system contains different sensors as: X-ray detectors, visible light cameras, NIR cameras, ultraviolet cameras and magnetic sensors, in the same sorting unit. The sorting unit allows advanced calibration options and fine-tuning of the installed sensors to achieve the best separation effect under controlled conditions. Finally, the processed material can be analysed and separated by the rejection mechanism, similarly to the industrial scale operation. At the same time, the process is carried out with limited amount of material allowing detailed statistical calculations for processed particles and all sensor types. The optimal settings and sensor types are specified for the industrial application.The paper describes the scale up of the results achieved for iron ore and coal, where the test work was first carried out using the new laboratory sorting system and where the industrial scale sorting system has been built, in the final stage. The industrial scale sorting results showed a very good correlation between the laboratory and full scale operation. Thanks to the detailed study carried out in the laboratory equipment, the settings of the sensors in the full scale operation provided much better separation efficiency. It was especially important to provide proper setting for the X-ray sensor data calculations, which can be very critical for achieving the best results. During the industrial scale sorting of coal, the input material had 40-55% rock particles as the direct source of ash in the coal stream. The optimal laboratory unit settings and transferring these settings to the industrial sorter, provided 98.8% efficiency for removing rock particles with only few % losses of coal."

Jan 1, 2016

By J. W. Bawden, J. Nantel

"The mine operator has two prime objectives when he operates a mine: (l) the mine must be safe, and (2) the mine must operate with the lowest possible costs. The operator constantly faces a dilemma; if he is over cautious with regard to safety, his costs may be very high, and if he is over-zealous in trying to reduce costs, the safety of his operation may be jeopardized.Modern bulk mining methods rely heavily on high productivity non-entry stoping techniques (e.g. open stoping, VCR, etc.). Such techniques have the advantage of removing the operator from the active and sometimes dangerous mining face and ofminimizing costly development. On the other hand, this generally results in a certain loss of flexibility in following irregular ore-waste contacts. If stopes are opened too large and/or are inadequately supported, severe dilution with resulting escalating costs usually results. If initial access drift support is inadequate for latter mine induced stresses high rehabilitation costs may also be incurred.Optimization of stope dimensions should logically occur as part of a general mine rock engineering program, within the over-all mine planning context. The same program should help highlight those areas where drift rehabilitation may be a problem.Whenever successful mining is performed, rock engineering is being applied, either by design or by chance. The cost implications of planned practical rock engineering as an integral part of mine planning and design can be very significant to the ultimate mining ""bottom line"". At Noranda Minerals Inc. allowable stope dimensions are derived using a combination of numerical stress analysis and empirical design techniques. This paper discusses the use of the above techniques and their limitations as tools for rock mechanics based stope dimension optimization. The potential cost implications of such design efforts within the general mine planning context are also addressed."

Jan 1, 1989

By Saba Gharedash

In this study the results of a series of numerical simulations which are conducted for one of the tunnels of the Mashhad metro line 2 project are presented to evaluate the role of tunnel face support pressure and soil strength parameters on deformation of tunnel lining and face deformation. To achieve this goal, comparative numerical simulations of a mechanized tunnel advance in soft non- homogeneous soil on top of the ground water table and beneath the building are conducted and sensitivity analysis is performed. Development of a step by step tunnel construction process is modeled using a three dimensional finite difference model (FLAC3D) taking into account all the relevant components of shield tunneling. In order to understand the mechanism of the effects of a variety of support pressures on face deformation and lining stresses, numerical simulations are conducted. It is found that the use of different face supports causes a considerable influence on the forces of tunnel lining. In addition, it is revealed that building weight help to change the stress paths and the stress distributions in the tunnel lining.

Aug 1, 2013

By Stephen G. Mlot

The evaluation of mineral projects involves the identification, mitigation and management of significant uncertainty. Benchmarking is an essential and effective way of increasing confidence and reducing uncertainty associated with input parameters and assumptions. Comprehensive and detailed benchmarking will ensure ?best practice? technologies, methods and systems have been considered and that the appropriate practices can be identified and incorporated into the project. In conjunction with the involvement of experienced industry practitioners, benchmarking is best employed throughout project evaluation to enable early identification of ?errors?, producing more accurate and predictable outcomes. Considerable time and effort is required to gather data and information, which should be benchmarked by the project evaluation team. There is a history of mining projects underperforming, on production, on costs and on return to the investors. The quality of mine plans and feasibility studies, and the quality of the input data is being questioned in many ways. Benchmarking assists sound project evaluation practices, by providing a database of actual results, to validate project inputs and outcomes, ensuring they are realistic and achievable. Benchmarking also provides unbiased, statistical support as the basis for sound investment decision making and ensures well considered decisions are made resulting in a more efficient study process. The evaluation of the quality of projects which are the subject of transactions also benefits from the use of real data obtained from a benchmarking database. Vendors are quick to highlight the benefits of their projects, and conceal the flaws, inflating the value. Buyers will want to quantify the potential of a project through the due diligence process relying on actual results from benchmarking. For the reasons broadly outlined above, benchmarking should be considered as an essential component of effective Project Evaluation.

Aug 1, 2013

By Lionel A. York

This paper outlines the type of water-bearing formations encountered in the Prairie Sediments and describes a method for effectively sealing these zones in order that shaft-sinking operations may be carried out with safety. Details are given of the procedure for carrying probe holes ahead of the shaft bottom. These probe or grout holes are employed for establishing a series of overlapping grout covers around the proposed shaft excavation to safeguard against large inflows of water during sinking. The pattern and length of grout covers cannot be standardized, and each cover needs to be specially designed to suit the varying ground conditions. In order to provide effective protection through the Prairie Sediments, the number of holes in any one cover would not be less than 8, and possibly as many as 64 would be required in certain zones. The length of covers would vary from 100 ft. to 250 ft. Emphasis is placed on the need for obtaining accurate geological and water information from exploratory holes, drilled in the shaft vicinity, in order to effectively plan all grout covers.

Jan 1, 1964

By T. C. Rao, Deb Kanungo

"The results of tests carried out on a 3-in. hydrocyclone have shown the linear relationships that exist between: (1) the flow-rate of water in the feed to and the overflow product from the cyclone; (2) the flow-rate of solids in the feed to and the underflow product from the cyclone. The underflow size distribution of an operation has been found to be linear and its usefulness in evaluating particle distribution in the cyclone has been discussed. Effects of design and operating variables on the above relationships have been discussed. The performance of this 3-in. hydrocyclone has been compared with that of a 20-in. cyclone, the results for which are available in the literature."

Jan 1, 1973

By Kevin B. Doyle

"Canada now supplies 23 per cent of the world demand for potash. Although potash is produced by many countries, Russia and Canada have the greatest reserves and capability to supply the future substantial demand over the next decade. It is estimated that demand will grow from 38,000,000 mt KCl in 1975-76 to 60,000,000 mt KCl in 1985-86. Current firm expansion plans and development underway in the world will move Russia to the forefront in supplying this demand growth. Russia will move from supplying 40 per cent of world demand in 1975 to supplying as much as 52 per cent in 1981. Canadian deposits suffer from natural disadvantages, such as high costs and risks of mine development and operation, and high-cost transportation to international markets, but experience has shown that these natural barriers can be surmounted to effectively compete in these international markets. However, Canadian potash is losing out in the race to supply the growth in the world potash demand over the next ten years because of artificial barriers raised through the unhealthy environment created by the current battle between different levels of government and the industry over resource taxation and legislation."

Jan 1, 1976

By A. E. Moss

"IntroductionTHE WORLD-WIDE search for iron ore has been vastly accelerated during the past fifteen years .and Canada is playing a most prominent role in this prospecting boom. During this period, the search for .and development of iron ore deposits in Canada bas proven eminently successful and there is every indication that exploration will continue to be active for many years.This paper has been prepared primarily for the information of those who have bad little or no experience in iron ore exploration. For convenience, it is divided into three parts: ( 1) a brief discussion of the marketing of iron ores, with special reference to Canadian production; (2) a summary of the main features to be considered when prospecting for or evaluating a potential iron ore deposit; and (3) an outline of the methods and procedures used in the search for the direct-shipping iron ores in the Quebec•-Labrador iron ore field.The Iron Ore MarketDue to the tremendous tonnages of high-grade direct-shipping iron ore indicated in the iron ore fields of the Quebec-Labrador and Steep •Rock areas, it might be assumed that there would have been a sharp decline in iron ore prospecting in this country. On the contrary, the development of these two major fields, which must be classed among the world's greatest, has been responsible for much of the current activity. The search for high and medium grade magnetite deposits is being• conducted in many parts of the country and a number of these have reached the development stage. Production is being expanded from the known fields, such as Wabana in Newfoundland and Michipicoten in Ontario."

Jan 1, 1955