Search Documents

By C. W. Davis

AN inclined shaft is usually more difficult to sink than a vertical shaft, yet it is often chosen because of the subsequent saving in cross-cuts required to reach an inclined ore body. This paper briefly discusses the factors which led to the choice of an incline and then describes the operations involved in the preparatory work and in the sinking. These operations included a programme of mining out the underground facilities and installing the structures required for a hoist-room, cable-raise, waste-pass, ore pass, two sets of skip dumps, and a collar station equipped with counterbalanced drop-rails. The shaft was sunk 1,000 feet and four stations were cut, each with loading pockets. As the sinking progressed, the rock changed from hard porphyries and dense cherts to blocky limestones and earthy rubble. These conditions called for a change in methods and it is to the red it of the shaft-sinking crew that they overcame the new difficulties as the shaft progressed, while maintaining a satisfactory monthly advance. The section mined out was nine feet six inches by seventeen feet overall. This gave room for three compartments: two skip compartments four feet three inches by five feet nine inches inside the timber, to handle two-ton skips, and a manway three feet six inches by five feet nine inches. The sinking began on December 16th, 1941, and was completed on February 15th, 1943.

Jan 1, 1945

By Sakellariou M., Ferentinou M.

Determination of the nonlinear behavior of multivariate dynamic systems often presents a challenging and demanding task. Therefore, complex geomechanics systems are an ideal area for the application of intelligent methods. Often the physical problem is controlled by nonlinear equations, conveying to the use of neural networks. Hudson, (1992a), aiming at efficient engineering modelling and design, introduced and developed Rock Engineering Systems (RES) approach, through the implementation of generic interaction matrix GIM. This approach has been used for a wide variety of rock engineering and other problems, resulting in many case studies available, which illustrate the application of RES to rock engineering problems. Considering the spectrum of the coding methods for the Generic Interaction Matrix, we suggest an objective coding approach. Among the five proposed coding GIM methods, the coding method according to the slope of Pi and Pj relation is relatively accurate, but it might be difficult or impossible to establish or estimate the exact relation of Pi vs Pj for most of the variables involved within a rock engineering system. Self organising maps, are a special type of unsupervised artificial neural networks, which can learn from complex, multidimensional data, and transform them to visually decipherable clusters. The proposed, coding of the GIM, is performed through the combined use of scatter plots produced through, (SOM), and the coding according Pi vs Pj slope. Naghadehi et al., (2013) constructed a database of worldwide experience, in open-pit mine slope stability, the selection of the principal factors was based on Hudson (1992a) who proposed an ‘atlas’ of factors affecting the stability of rock slopes. Slope classification was performed according to status of stability. The rating of the GIM matrix was completed, coupling scatter matrix produced by SOM training, and Pi vs Pj slope plot. Results refer to the identification of clusters, according to status of stability within the original multivariate data set, and the rating of the principal factors according to the dominance and interaction intensity within the open pit mines RES.

Jan 1, 2015

By S. Bozorgi, K. Anders

"The automotive applications of heat treatable AlCu cast alloys are designed for performance at high temperature, which can be improved using specially alloying element as well as different heat treatment. In this research work an effect of alloying element such as Cu, Ni and heat treatment on microstructures and mechanical properties of AlCu alloy were investigated using optical microscope (LIMI), scanning electronic microscope (SEM) equipped with energy dispersive X-ray detection (EDS), Differential scanning calorimetry (DSC) and mechanical testing. It was found that during solidification most of the elements Cu, Mg and Ni segregated at the grain boundaries in the form of Al2CuMg or Al7Cu4Ni and a very small part of Cu and Ni element dissolved in the FCC-Al matrix. The latter is not completely reclaimable for strengthening mechanisms in FCC-Al matrix in its as-cast state. The results of mechanical test show that yield strength and ultimate tensile strength increases after heat treatment significantly compared with the as-cast state. Furthermore the mechanical properties at elevates temperature (240°C) is higher with higher Cu+Ni+Si containing alloys compared with the less Cu+Ni+Si containing alloy.INTRODUCTION Due to the high strength-to-weight ratio, high strength and ductility at room- and elevated temperature, AlCuSi cast alloys are widely applied in the automotive industries specially for producing cylinder head and engine block, where modified alloys with enhanced metallurgical properties are always needed to satisfy the ever increasing demands for the applications. The AlCu based cast alloys can be strengthened by age hardening. The precipitation processes from which this hardening is derived can be attributed to the presence of selected trace element additions or micro alloying, which can change the process or kinetics of precipitation in age hardenable AlCu cast alloys (Polmear, 1998; Morris, 1991). Furthermore their strength is mainly controlled by the aging process through the precipitation and growth of very fine precipitates of the ?'-phase (a semi-coherent, metastable form of the equilibrium Al2Cu phase) from the Al and Cu Guinier-Preston (GP) zones. Several studies have shown that solute clustering occurs prior to the precipitation of GP zones, and this modifies both the nature and kinetics of the precipitation process. The typical size of GP zones is in the order of tens of nanometers, and the chemical composition of these precipitates is not easily measured, even with a typically analytical electron microscope (Polmear, 1989)."

Jan 1, 2018

By John E. Udd

I N Part I of this paper, Professor Morrison suggested that our technique of causing cracks to develop around openings in a sheet of photoe1ashc plastic is, in effect, a laboratory-scale rockburst. Our investigations have indicated that the location and direction of these cracks are predictable, and that their growth can be controlled. On several occasions, we have been able to cause these cracks to propagate sufficiently slowly to be followed, with the naked eye. In practice, the rate of growth, gradual or sudden, would depend upon rock properties. This part of the paper presents an analysis of the stresses surrounding the openings before and after failure and also this author's views on the causes and after-effects of cracking. An attempt is made to correlate the stress patterns with those deter-mined from pure mathematics. Considering that the openings, except for the central enlargement, are long apertures with somewhat rounded corners, they might be compared with elongated ellipses having axes ratios of about 20:1 or with

Jan 1, 1963

Operating CIP/CIL gold recovery plants in the arid regions of Western Australia face unique challenges due to water and ore quality issues. The presence of cations of Mg, Fe and Cu metals in water supplies and leached sulphide ores can have considerable effect on plant consumption of lime and cyanide, due to pH buffering and complexation effects. Reagent costs are critical to many of these operations. In this paper, computational modelling is used to analyse a number of process options to mitigate such issues. This requires careful consideration of the chemistry of the process system, and the ability to predict accurately the response of speciation and precipitation reactions to changing process conditions. The Mg-Fe-Cu-CN-H20 system is specifically modelled in this application. The Gibbs Free Energy Minimisation thermodynamic framework has been selected to model equilibrium phenomena. Furthermore, this approach has been extended to the process flowsheet level, incorporating multiple unit operations and recycle streams in a steady-state mass balance model. The Gibbs equilibrium composition module of HSC Chemistry software has been successfully integrated into the commercial flowsheeting package SysCAD. Consideration of the Gibbs Energy Minimisation capabilities of other flowsheeting packages has also been given. This approach has been successful in simulating the aqueous process chemistry typical of such plants. It has resulted in a predictive capability where equilibrium states respond appropriately to process changes. Potential cost savings may be identified by examining alternative process conditions to minimise overall reagent consumption.This methodology may be extended to other hydrometallurgical plants where issues of solution ideality, temperature and other equilibrium processes are sufficiently understood.

Jan 1, 2005

By J. Ander

About fifteen years age some mines in western Canada commenced using Diesel engines, partly for development work but also for operations on quite a large scale. In the Eastern mining field, the Diesel engine made its appearance some eight years ago and has since, at quite a number of mining plants, proved to be a reliable and economical prime mover. As a result, it is today used more extensively than could have been foreseen only a few years ago, and it is reasonably safe to predict that the next few years will see the Diesel engine utilized to a still greater extent in the Canadian mining industry. It is not much more than thirty years since the first Diesel engine was put in operation. During the early years of this century, the Diesel engine took, so to say, its first faltering steps in public service. Since then it has reached a high state of perfection, and its importance has grown in a most remarkable way, until today it is used in practically every field where power is required. It is slowly but surely superceding steam for a great many purposes, as, for instance, for ship propulsion. While in 1921 only about 8 per cent of all tonnage launched was motor-driven, the proportion had grown to 38 per cent in 1927, and for 1929 it was slightly over 45 per cent. Some of the finest passenger liners afloat are Diesel-driven. In the early days, Diesel engines were built only in comparatively small units. Today engines with a capacity per unit of up to 10,000 horsepower, or even more, are being built for marine and stationary purposes.

Jan 1, 1930

By D. Mas Ivars, K. Suzuki, J. A. Vallejos

"A comprehensive geotechnical characterization has been undertaken at the El Teniente mine to describe and determine the rock mass behaviour strength properties of the primary copper ore. The Synthetic Rock Mass (SRM) modelling approach is used to simulate the mechanical behaviour of this heavily and unfractured rock mass. The micro-parameters of the model have been calibrated against mechanical properties and scaling laws for intact rock and veins, in order to represent virtual samples of four different geotechnical units. Results can be used to predict the rock mass scale effects, anisotropy, and brittleness properties that cannot be obtained using empirical methods.INTRODUCTIONThe primary copper ore at the El Teniente mine is described as very competent and massive, given that it exhibits a brittle behaviour (Rojas, Cavieres, Dunlop, & Gaete, 2000). This description is coherent with the geological description of the rock mass, which does not have discontinuities match as the definition provided by International Society of Rock Mechanics (ISRM, 1981). Only faults can be classified as discontinuities, but they are widely spaced. The primary copper ore has a high frequency of veins, where the cooper mineralization is hosted, these vein network structures are known as stockwork. Soft veins containing weak minerals as infill (chalcopyrite and anhydrite) control the disassembling of the rock mass during caving (Brzovic & Villaescusa, 2007).Presently, there are mainly two traditional methods used to estimate the strength of the rock mass: 1) determination of the strength envelope of the rock mass using scaling parameters from laboratory tests and 2) using numerical modelling based on back analysis of previous experiences of failure observed and measured in mining or civil excavations. The primary copper ore of El Teniente mine has no fractures; therefore, it is difficult to determine a rating that would enable to scale laboratory data, such as, RMR (Laubscher, 1977) or GSI (Hoek, 1994). This is the reason why the first option is not valid unless the entry data is manipulated or adjusted in order to obtain reasonable results. The second option requires, in general, a good characterization of a previous failure event in the rock mass, which is not always available. In recent years, new techniques of numerical modeling have been developed (PFC3D, ELFEN, Abaqus). Those methodologies are the third way to estimate the strength of the rock mass, but they are still in development. Particularly, the concept of SRM developed by Itasca is implemented in this study (Pierce, Mas Ivars, Cundall, & Potyondy, 2007; Mas Ivars et al., 2011), aiming to capture the real behaviour of the rock mass."

Jan 1, 2015

By T. Sugawara, S. Hara, Y. Mitsui

Surfaces of rock slopes in cold regions often become frozen in winter. Therefore, understanding time-dependent behavior of frozen rock, as well as that of unfrozen rock, is important for long-term stability assessment of rock slopes. In this study, a series of uniaxial compression tests and creep tests were carried out on Shikotsu welded tuff under dry and water-saturated conditions at -20 °C to clarify timedependent strength and deformation of the frozen rock. The influence of water content on them also was investigated. It was found that the amount of deformation of the water-saturated specimen was much greater than that of the dry specimen. It also was found that the creep behavior of the water-saturated specimen was similar to that of polycrystalline ice. These show that deformation of the water-saturated specimen is strongly affected by pore ice. The UCS of the water-saturated specimen was approximately equal to that of the dry specimen at a strain rate below 4.2×10-6/s, and its value was about 17 MPa. However, the former increased up to 26 MPa at 4.2×10-4/s with loading rate, whereas there was little increase in the latter. This means that the UCS of the water-saturated specimen was always greater than that of the dry specimen at higher strain rates. The creep life of water-saturated specimens was longer than that of the dry specimens at stress level greater than 15 MPa. These results of UCS and creep life show that inclusion effect due to presence of pore ice plays an important role on strength of the water-saturated specimen. Creep life of the non-failure specimen that was loaded for more than three days was estimated by the relationship between creep life and axial strain rate at 10 s on failure specimens. It was found that creep life of the water-saturated specimens was shorter than that of the dry specimen at stress levels less than 14 MPa. This suggests that estimation of creep life of frozen rock under water-saturated condition is important for the stability assessment of frozen rock slopes. It was clear that the loading-rate dependency of UCS was related to the stress-level dependency of creep life in both dry and wet conditions. This indicates that there are common fracture mechanism in creep and uniaxial compression tests. It also indicates that the creep life can be estimated by the relationship between the UCS and the loading rate. The time dependencies of the water-saturated specimen were in good agreement with those of polycrystalline ice. This confirms that pore ice strongly affects the strength of the water-saturated specimens as, well as the deformation behavior.

Jan 1, 2015

By Roger K. M. Bellows

The last coal-fired power plant to be built in Canada came into operation in 1994. Since then, Canada?s electricity requirements have grown substantially but no new coal-burning plants have been built. This country has abundant resources of coal from coast to coast, but in recent years, this has not affected our choice of fuel. In many other countries this is not the case, and the use of coal is growing rapidly. Although this presentation covers the topic from an Alberta perspective, some of the conclusions can be extrapolated to the rest of the country, and perhaps even to other countries. The coal found in the Alberta plains is particularly attractive because of its low cost and low sulphur content. Yet coal is no longer the fuel of choice, and a long-standing provincial government policy to favour coal for electricity generation has been ignored for more than a decade. Considering the lack of good alternatives, it seems obvious that we should look to coal as our primary energy source in the generation of electricity and for other industrial applications. This paper discusses some of the reasons that coal has fallen out of favour, particularly with respect to electricity generation. The significance of the deregulation of the electricity industry will not be ignored. In addition, the author will offer his opinion on the question of what it will take in order for coal to once again become the favoured fuel.

May 1, 2001

By Lynn I. Kelley

Potash is the primary industrial mineral produced in Saskatchewan, followed, in terms of gross value, by aggregate, sodium sulphate, salt, potassium sulphate, peat, clays, silica sand, calcium chloride brine and "clinker." Potentially economic deposits of kaolin, diamond and building stone are under evaluation.

Jan 1, 2001

By Jared Onyirimba, Jim Viellenave, Hal Demuth, Dale Verran, Chad Sorba, Errol Lawrence, David Bronkhorst

As outlined within the Denison Mines Corp’s (“Denison”) Pre-Feasibility Study ("PFS") completed in late 2018, additional work is required to increase confidence and reduce risk associated with the application of the In-Situ Recovery (“ISR”) mining method at the Phoenix deposit, located on the Wheeler River Uranium Project (“Wheeler River” or the “Project”) in northern Saskatchewan. The successful application of ISR in any geological environment largely hinges on three fundamental requirements, 1) permeability (of the deposit), 2) containment (of the mining solution) and 3) leachability (of the mineralization). Denison has designed several staged technical programs to progressively reduce risk associated with these requirements as the Company advances the Project toward a Feasibility Study (“FS”) and Environmental Impact Assessment (“EIA”). This paper will discuss the scope and results of certain technical programs being undertaken as the Company aims to develop the first ISR mining operation in the Athabasca Basin.

Jan 1, 2020

By F. Prescott, D. Hiam-Galvez, J. Hiam

Mines are frequently located in remote areas with little conventional employment and few opportunities for the existing population. The development and operation of the mines results in several years of intense activity followed by a near-complete reduction in employment and opportunities after the mines are closed. Designing Sustainable Prosperity (DSP) is a method for rectifying this situation by designing for long-term growth in areas that host mines. This process involves the participation of local and national governments, local community, mining companies, investors, academics and those with sector expertise. The mines will be the catalyst for regional sustainable development. If successful, long-term economic and environmental prosperity should be the result for the areas affected by mining and, in some instances, promoting the regions as centres of excellence for a particular industry. This paper will describe how the concept works using the copper producing region of Peru and Chile as an example. Designing sustainable prosperity starts by looking at regions based on the natural resources and skills available, the infrastructure and possible energy sources. Integrated natural resource models and innovative market studies, followed by education and skills requirements, are then established to determine the potential for the region and what needs to be done to realise the possibilities. INTRODUCTION Industry 4.0, or i4.0, dubs the fourth and current industrial revolution. Where previously they have been founded on ever-increasing consumption and production, i4.0 distinguishes itself by its partial focus on reducing resource intensity; lightweighting, energy efficiency, sensors and automation to improve resource efficiency. Industry 4.0 is an era of artificial intelligence, genome editing, biometrics, renewable energy, 3D printing, autonomous vehicles and the Internet of Things (Lu, 2017). These drivers represent key opportunities for the economic future of nations and regions.

Jan 1, 2019

By R. D. Brown

In the spring of 1977, Revenue Canada announced its intention to proceed in 1978 with a plan to impute a taxable benefit on interest-free and low-interest loans provided to employees. Such loan arrangements are often an important aspect of the compensation packages provided by many companies to their employees. Since the original announcement, there have been many submissions to Revenue Canada opposing this change, and the Finance Minister has now brought down a compromise solution with the introduction of a proposed amendment to the Income Tax Act. The amendment, which would not take effect until the 1979 taxation year, would require an employee, a shareholder or a related person to include a benefit in income measured as the difference between the interest on any such loan computed at bank prime rate and any interest actually paid. Only the amount of such a benefit in excess of $500 in a particular year would be required to be included in income. Of particular interest is the exclusion from these benefit rules of loans up to $50,000 in respect of the purchase of a house on the relocation of an employee and loans provided for the purchase of shares of an employer corporation.

Jan 1, 1978

By Olivia Gamache

When working in remote and extreme environments, projects are faced with new challenges for engineering and project execution. This is heightened when also working in countries with a developing environmental regulatory framework, small skilled workforce available for recruitment, and minimal infrastructure such as power, roads, and water. There is an increasing realization that social and environmental aspects need to be built into project execution. Giving proper attention to these issues during project development and execution, and maximizing opportunities is an ongoing challenge.

May 1, 2013

By John H. Morris, R. Gwilym Roberts

"The Upper Beaver Mine, Kirkland Lake, Ontario, is a copper-gold deposit in mafic flows and sedimentary rocks. The deposit consists of a number of orebodies of two types: copper- and gold-bearing chalcopyrite-pyrite-magnetite ore; and gold-bearing quartz veins. Chalcopyrite-pyrite-magnetite ore occurs in two structural forms: as cherty interflow material in coarse clastic roks underlying flows; and as veins. Both sedimentary and vein ore occur in each orebody. The goldbearing quartz veins occur in interflow sedimentary units and at the contacts of oligoclase porphyry dykes.The deposit is in a localized, volcanic-sedimentary basin which began to develop during the emplacement of the upper units of the pyroclastic and sedimentary Gauthier Group, and continued to the early mafic flow activity of the overlying Kinojevis Group. The formation of the volcanic-sedimentary basin is ascribed to the D0 deformation. The deformation is significant in terms of the structural configuration in the mine area, and may be significant regionally, but this has not been demonstrated. The early deformation was followed by two tectonic deformations. D 1 is associated with a penetrative mineral foliation, axial planar to upright mesoscopic folds and striking parallel to the trend of regional fold structures. Mesoscopic flexural-slip folds, kink folds and fracture-crenulation cleavage are attributed to the D2 deformation. It is probable that no large-scale fold structures are associated with the D2 deformation. The gold-bearing quartz veins were folded during the D1 deformation.The close spatial relationship of copper-gold, chalcopyritepyrite- magnetite veins with chalcopyrite-pyrite-magnetite in cherty inter flow material is strong evidence for the derivation of the veins from the sedimentary ore by hydrothermal, metamorphogenic processes. By analogy, it is suggested that the gold-bearing quartz veins were formed by similar processes."

Jan 1, 1982

By J. M. Belland

This paper deals with the geology of the Smallwood mine in relation to its influence on mining and milling operations. Structure within the orebody, and variations in ore grade and material types, will be described and associated with the various drilling, blasting and milling operations. The orientation of planes of weakness, either bedding or jointing planes, and contacts between extremes in material types influence the size of the broken material. Generally speaking, variations in grinding rates and recovery can be associated with stratigraphic sequence and metamorphism.

Jan 1, 1966

By X. Cao, H. Huang, Z. Dai

"Crystal phase of copper-containing slag regulation by the slag viscosity, cooling speed and cooling method, where the slag viscosity is related to the temperature and alkalinity. According to the mineralogy properties of a copper-containing slag, experiments of crystal phase regulation and flotation were conducted. When the copper-containing slag that adding a small amount of calcium oxide was cooled slowly at a rate of 3°C/min and about 1050°C n a cinder inclusion system, the viscosity of slag can be remained under 0.25 Pa·S and more than ??% of copper particles that the grain size is larger than 20 ?m in slag. The whole flow of flotation experiment was carried out to recover copper from the copper-containing slag with crystal phase regulating and the copper concentrate grade was ?????%, the recovery efficiency of copper was 94.18%.INTRODUCTIONChina's annual output of copper slag is more than 6 million tons, the current total has reached 80 million tons. It is equivalent to 640 thousand tons of copper metal with the copper grade of 0.82%. Most of the smelting slag were storage. It is not only occupy the land and pollute the environment, but also make a huge waste of resource (Alp, Deveci, & Süngün, 2008; Carranza, Iglesias, Mazuelos, Romero, & Forcat, 2009; Gorai, & Jana, 2003), therefore, it is good way to achieve copper slag resources by the effective recovery of valuable component from copper smelting slag, which is an important measure of the current process of copper smelting slag and implement the central authorities to vigorously develop the circular economy, improve the recycling of resources, increase copper production of intensive development (Zhou, et al., 1994; Zhang, Zhang, & Wang, 2005). Currently, researches on comprehensive utilization of the coppercontaining slag made a much progress (Wei, 2004; Liu, Gai, Yang, Sui, Li, & Fu, 2008; Liu & Zhu, 2008; Zhang, 2010; Sun, Chen, & Tang, 2012; Qin, Wang, Ren, Wei, Peng, & Gu, 2012). Flotation is one of the most effective method to recover the copper from smelting slag, which has the features of low cost and high efficiency (Song & Liu, 2001; Zhang, Wang, & Li, 2012). But the copper particles in the copper smelting slag distribution is very uneven, and the thickness of the material is very serious. The copper content in the micro level is higher, the size of copper sulfide ore is less than 0.043 mm, which leads to the difficulty of the monomer dissociation (Tossavainen, Engstrom, Yang, Menad, Lidstrom, Larsson, & Bjorkman, 2007; Moustakas, Mavropoulos, Katsou, Haralambous, & Loizidou, 2012). In this study, according the process mineralogy of a smelting copper slag, the crystal of smelting copper slag was optimized by controlling the temperature, alkalinity, cooling rate and cooling method, which makes the fine copper mineral particles in the copper slag crystal further, and can be used to meet the particle size requirements of flotation, thereby enhancing the flotation of copper."

Jan 1, 2016

By B. Surender Mohan

Mother Earth being a treasure of minerals, it is prime duty of the mankind to preserve this natural source to ensure steady growth of the nation. Utmost care is to be taken to see that these natural resources are explored and exploited scientifically in a sustained manner to ensure that the resource base improves and last longer. In this backdrop, the topic of ?Lignite - its resource and technology options to exploit deep seated deposits? is an apt subject to be deliberated upon in the present context, where the shallow deposits may slowly get dwindled. I shall deliberate upon the resource base of lignite, production profiles of the last five decades, consumption pattern, demand / supply projections, future available technology options to exploit the deep seated deposits, growth trends of the sector etc. in my paper. With the available resource base and future technology options, I can confidentially make a statement that ?lignite will remain as cocontributor along with coal to India?s energy generation and may well maintain its same status in the 21st century too, as it has been in the later part of the twentieth century?.

Aug 1, 2013

By M. Mbonimpa

Field experimental cells were constructed in 2007 to assess the performance of different cover scenarios for the reclamation of the Parc 1 tailings disposal facility at the Westwood-Doyon Mine site (Abitibi, Quebec). Three configurations of cover with capillary barrier effects (CCBEs) with different thicknesses and material types for the moisture retention layer (MRL) were studied. MRL with 80 cm till, 40 cm till, and 40 cm clayey silt were used for cell nos. 2, 3, and 5, respectively. The capillary barrier layer (CBL) and drainage and protection layer (DPL) of the CCBE consisted of 30 cm gravel. A reference cell without cover was also constructed to compare the geochemical performance of the CCBEs. Due to an unexpected flooding in the leachate exit area of the cells in spring 2008, the cell instrumentation for hydrogeotechnical monitoring was postponed to spring 2009. Changes with time in volumetric water content, suction, soil oxygen concentration, and temperature were measured at different depths. This paper presents and discusses preliminary results obtained from spring 2009 to autumn 2010. In all cases, the degree of saturation Sr is lower in the CBL than in the MRL, indicating the presence of capillary barrier effects at the interface of these layers. Cell nos. 2 and 5 showed hydrogeotechnical behavior typical of an effective CCBE, with Sr maintained above 85% in the MRL and lower than 30?50% in the DPL and CBL. Based on the obtained results, and as expected, MRL thickness and the type of construction material used appear to affect the hydrogeotechnical behavior of the CCBE. Oxygen concentration profiles through the CCBEs were used to estimate the oxygen flux, and results indicate that cell nos. 2 and 3 performed better than cell no. 3. CCBE performance is currently being investigated using the geochemical monitoring data.

Aug 1, 2013

By J. C. Mitcheson

Mr. President, Mr. Mayor, Ladies & Gentlemen: IT GIVES ME great pleasure to have the opportunity, today, to speak on behalf of all the constituent. bodies of the Common-wealth Council of Mining and Metallurgical Institutions. For the past month we delegates have been right royally entertained across the length and breadth of Canada by Provincial Governments, City Councils, and other equally generous public organizations and private corporations. On this occasion, however, the President of The Canadian Institute of Mining and Metallurgy, our good friend Dr. H. J. Fraser, has been our host at the enjoyable reception preceding this Institute Luncheon, which luncheon was sponsored by our official host, The Canadian Institute of Mining and Metallurgy, one of our .constituent bodies.

Jan 1, 1957