Search Documents

By J. M. Whatley

"IntroductionIN UNDERGROUND mining operations, the mine hoist has become one of the most important and one of the most expensive single pieces of equipment. As the means of transporting men and materials to the face, broken ore to the mill, and waste to the dump, it is often the very lifeline of a mine and must operate with dependability and efficiency or the whole operation will suffer. The mine hoist has become synonymous with safety. In few other types of mechanical equipment do so many men so frequently and completely place their lives. In Canada, more has probably been done to assure safe hoisting than in most other countries, but, unfortunately, this has resulted, in many cases, in the mines having to pay a high price for equipment. Hoist manufacturers have carried out much research in recent years in the endeavour to keep down these costs and at the same time maintain or improve the efficiency and safety of their products. Broadly classified, the bases for design research are dependability, efficiency, safety, and first cost.Probably the greatest single factor influencing the design of mine hoists was the introduction of electric motor drives. It was not until about 1905 that an effective start was made in the development of electric mine hoists, and then only with machines of small size. From that time on, however, progress was rapid, as may be gauged from the fact that by 1910 one large group of mines in Johannesburg had in use, or on order, fifty-four three-phase hoists and four Ward-Leonard. type hoists."

Jan 1, 1953

By Mohamed Hamoud

Relative permeability curves represent an important element of special core analyses, but challenges remain in obtaining valid results and the extrapolation and use of existing permeability results is problematic. This situation is compounded in cases where core properties are altered from changes in effective stress. During the production of oil and gas reservoirs, the effective stress changes as a result of changes in pore pressure or temperature. Therefore, changes in rock properties such as porosity and permeability will occur and will consequently influence reservoir performance calculations. An experimental program was carried out to understand the behavior of dense, reconstituted sand samples at low effective stress states. Drained triaxial compression tests were set up to study the effect of stress alteration on relative permeability data through porous media. Initially, a saturation stage was performed followed by isotropic loading to bring the core sample to reservoir fluid and stress conditions. Then, while axial (deviatoric stress) loading was applied to the sample, a series of absolute and relative permeability tests was performed under steady state flow at different levels of strain during pre and post peak shearing stress. The stress-strain behavior results from the study revealed that the absolute permeability decreased during isotropic loading (compaction) and increased during shearing (dilation). However, the shape of relative permeability curve changed from contraction to dilation and showed higher initial kro and the lower initial kro respectively. The goal of this project was to understand the behavior of both absolute and relative permeability at different stresses. It is expected that geomechanical processes will be adopted for special core analyses to support the current integration of geomechanics into reservoir engineering. This will be required if, during SAGD, conventional and/or unconventional reservoir simulation, reservoir engineers implement a proper set of relative permeability data at each in situ state of stress, instead of constant curves throughout the field?s life.

Jun 1, 2012

By J. Mizera, B. Adamczyk-Cieslak, K. J. Kurzydlowski, A. Dobkowska

"AZ31 is the one of the most popular magnesium alloy using in the modern industry. It is well known, that compared with steel, magnesium alloys posse better properties, such as light mass, high specific strength or thermal conductivity. It should be noted that their application is limited by poor corrosion resistance. In this work the corrosion behavior of AZ31 magnesium alloy as cast and after heat treatment were described with the use of testing in neutral salt spray atmosphere.To characterise corrosion resistance and describe layers built on the surface it was necessary to do the metallographic observations with the use of optical microscopy. After that influence of heat treatment for AZ31 corrosion resistance was examined. Measurements were conducted by electrochemical impedance spectroscopy (EIS) and by neutral salt spray tests in artificial atmosphere. Surface and cross section morphology after removal of corrosion products were observed with the use of scanning electron microscopy (SEM).The weight loss measurements show that there is no significant difference between alloys as cast and with following heat treatment.INTRODUCTIONMagnesium and magnesium alloys are popular in modern industry because of the low density and good formability. Magnesium alloys are described by few properties which have got significant influence for their application in transportation and electronics industries (Feliu & Liorente, 2015). Their wide application is limited by poor corrosion resistance. As it is well known Mg is one of the chemically most active metal. Corrosion resistance of Mg alloys depends on several factors, such as impurities, chemical composition or working conditions (Cheng, Qin, Wang, & Zhang, 2009). That all causes that there are many different ways to find well defined and good solution of magnesium alloys processing to improve their corrosion resistance.There are many different versions about the influence of aluminum on the corrosion resistance of magnesium alloy. It is known that intermetallic compounds such as Mg17Al12 due to ß-phase content plays the minor role for corrosion resistance. It is proved ß-phase acts as cathode and it has good ability to build passive layer in broad pH ranges. However it should be noted that mentioned behavior depend on size and distributions of ß-phase in the microstructure (Singh, Singh, & Das, 2015)."

Jan 1, 2016

By J. F. Henderson

THE National Advisory Committee on Research in the Geological Sciences was established seven years ago - in 1949. In 1952, shortly after the Committee had really begun to function and had issued its first report, a paper ( l) was presented describing the objectives and organization of the Committee and the progress to that time. Another four years have gone by and the Committee feels a further progress report may be of interest. HISTORY Ten years ago, in 1946, the Geology Division of the Institute set up a Committee on Geological Research. This Committee, under the Chairmanship of Dr. J. E. Hawley, recommended that "a National Advisory Committ.ee on Research in the Geological Sciences be formed" (2). With the backing of the President and Council of the C.I.M. this recommendation went forward to the then Minister .of Mines and Resources and, with his approval, to the Committee on Scientific and Industrial Research of the Privy ?Council. As a result, the National Advisory Committee was set up in 1949.

Jan 1, 1956

By A. Miura, G. Granata, C. Tokoro, A. Fuwa

"The high copper demand as well as the lack of new high-grade deposits, are pushing the copper industry to process low-grade and refractory ores containing chalcopyrite. However, for a quantitative dissolution of copper from the chalcopyrite, the leaching performances still need to be improved. In the present research, we studied and optimized the iodide-assisted leaching of chalcopyrite in H2SO4-Fe2(SO4)3 media. The evolution of surface species during leaching was determined by x-ray photoelectron spectroscopy (XPS) and mineral liberation analysis (MLA). Inductively-coupled plasma spectrometry (ICP-MS) was used to determine the dissolved copper. Significance of experimental results was assessed by statistical analysis while a kinetic analysis of the leaching process was performed by fitting the experimental data with the Shrinking-core model. Results showed the significant positive effect of iodide on copper extraction rate. In the presence of KI, the dissolution rate of copper was almost double than in the parallel experiments without KI. Whether using KI or not, elemental sulfur was generated on the surface of the leached chalcopyrite. Nevertheless, in the presence of KI, the passivation layer did not arrest the leaching. Analysis revealed that the leaching rate was limited by the chemical reaction control step.INTRODUCTION Due to the large demand of copper, processing low-grade ores containing copper sulfides such as chalcopyrite (CuFeS2) has become unavoidable (Watling, 2013). Since ores with CuFeS2 may also contain appreciable amounts of arsenic that cannot be smelted, and because low-grade ores are uneconomic to smelt, the hydrometallurgical technologies are crucial for recovering the copper (Dutrizac, 1978). Sulfate-based processes are attractive because of the lower operating costs and because the sulfate ion is more suitable in case copper would be recovered via electrowinning. In ferric sulfate solution, chalcopyrite undergoes oxidation due to the large amount of Fe(III) and dissolution due to the presence of the sulfate ion (Majima, et al., 1985). The leaching reaction in ferric sulfate medium can be represented as in (1):"

Jan 1, 2017

By M. Romana

"RMR geomechanics classification is being used all over the World as a useful tool for tunnel predesign and construction. Bieniawski (1989) provided guidelines for tunnel excavation and support, according RMR numerical values; guidelines which are now included in almost all tunnelling books, regulations, and Internet portals. But in the last 25 years tunnelling techniques have changed and some of the guidelines have become obsolete.. The conditions of tunnels for the 1989 guidelines application were: horseshoe shape; 10 m width; vertical stress < 25MPa; construction by drilling and blasting. Actually a substantial number of tunnels are mechanically excavated. The tunnel themselves are now bigger: a span of 14 m. is very common for transportation tunnels. The guidelines included the following concepts: excavation method, rock bolts (20 mm diameter, fully grouted), shotcrete, steel sets. There is an increasing gap between the 1989 guidelines and the practice: in many tunnels different to-the-case excavation and support requirements are established. Bieniawski himself has published a paper (Lowson & Bieniawski, 2013) with different guidelines based in Lowson’s practice, with no explanations and/or justification.In this paper a new set of RMR tunnelling guidelines is proposed taking account of the actual industry conditions, and increased safety regulations. The 5 classes’ limit RMR:values (80,60,40,20) are no more useful actually: Values of RMR (70, 50, 30) are used in practice to define quite different tunnelling techniques. Consequently a 10 subclasses system is proposed. Each subclass covers a span of 10 RMR points. As the number of mechanically excavated tunnels has increased a new correction factor is necessary, according the excavation method.The proposed 2014 RMR guidelines are for tunnels 10 to 14 meters wide, the world practice for new roads/railways tunnels. Many tunnels for water/ services are smaller with smaller support needs. Wider than 16 m caverns are out of the RMR system.It is not possible, nor desirable, to propose only a value for support in each subclass. The new guidelines propose an interval of values for certain types of support. More pessimistic values must be chosen for wider tunnels, tunnels with lower RMR values in each class and cases when a higher safety factor is asked for. More optimist ones are chosen for narrower tunnels, and higher RMR values. Some alternatives are almost complementary, others are contradictory. Sometimes several different techniques are proposed Guidelines are not automatic options. Good engineering judgment must be used when choosing between the different alternatives. Guidelines are not mandatory suggestions."

Jan 1, 2015

By Benoît Valley

Optimization of the mining sequence in terms of economics (maximizing net present value) often leads to multi-front mining methods generating pillars. Significant resources are tied up in these pillars, but mining them is often challenging. In order to improve our understanding of rock mass behaviour while extracting these pillars, an extensive monitoring program has been designed and implemented at Vale?s Coleman mine (Sudbury, Canada). The program focuses on existing and new technologies that have potential for monitoring deformation and rock mass property changes. It includes both active and passive methods: gravimeters, multi-point borehole extensometers, fiber optic strain meters, fixed and portable three-component seismic arrays, borehole imaging and sonic logging, and, repeated LiDAR surveys. This paper reports results from an initial project phase, when only a small amount of mining has taken place. The goal was to test and compare technologies in order to assess their sensitivity, accuracy, repeatability and suitability for underground mining conditions. Value is gained by having a broad range of monitoring devices running side by side, enabling comparisons and benchmarking.

Jun 1, 2012

By Bruce Macdonald

Operational reservoir management activities such as cyclical steam, water or CO2 injections frequently cause surface micro-deformation. InSAR monitoring from space based sensors of this surface deformation has become a valuable approach to confirm and monitor extraction and injection activities. Sequestration of CO2 into deep saline aquifers is discussed as an important long term solution to slow future climate change. This method requires reliable continuous monitoring to assure that captured CO2 is sequestered in the substrate for ?all time? (typical minimum requirement by law is 20-30 years). We have shown that combining flow and deformation modeling with spaceborne synthetic aperture RADAR interferometry (InSAR) measurement of ground uplift caused by the underground release and spreading of the CO2 can be forged into a powerful tool to monitor sequestration. We used a novel InSAR approach to resolve the surface motion over the In Salah, Algeria CO2 sequestration site. Our approach exploits all information contained in an interferometric stack by exploiting both persistent distributed as well as persistent point scatterers. Displacement time series are obtained with a network inversion approach applied after topographic error and preliminary atmospheric correction of the network (dual-scale technique). After inverting the original network data to common master we then use an advanced spatio-temporal filtering scheme to remove the remaining atmospheric phase components down to scales of 1 km or less. By comparing final displacement series from multiple interleaving InSAR stacks we show that the accuracy of our refined solution to detect uplift outside of significant temporal data gaps in the InSAR stack is significantly better than 1 mm per year. We further show that accuracy and robustness to data gaps are both significantly improved by co-inverting multiple datasets with the same and different sensors. This co-inversion method also allows the seamless continuation of the monitoring from one sensor to another.

Jun 1, 2012

By R. E. Phelan

Introduction The Flin Flon deposit was discovered by Tom Creighton, an experienced prospector and trapper, who in 1914 made his headquarters at The Pas, Manitoba, and still lives there. The discovery was made in the fall of 1914, and Creighton and his associates spent the next summer in investigating the find. In August of 1915 the first claims were located. The property was optioned to Hayden Stone & Company, and in the spring of 1916 they started a diamond-drill campaign. Hayden Stone spent $50,000 on the property and, among other things, completed over 7,500 feet of diamond drilling. The ore not being as high grade as expected, and also being complex in character, Hayden Stone then abandoned their option. In the spring of 1917, Messrs. Earle, Faskin and associates took an option on the property and started an extensive drilling campaign. This campaign accomplished approximately 18,000 feet of drilling and secured for the Faskin interests a 32 per cent interest in the property. In 1920, W. B. Thompson and The Mining Corporation of Canada secured an option, and, while this option was in force, sunk two shafts in the ore-zone and did a considerable amount of drifting and cross-cutting in the ore to study the manner in which it occurred in place, and, by actual channel sampling, to check the grade indicated by the previously accomplished diamond drilling. All of this work had indicated that an ore-body existed on the property containing at least 18,000,000 tons of ore, assaying as follows: gold, 0.074 oz./ton; silver, 1.06 oz./ton; copper, 1.71 per cent; and zinc, ). 45 per cent (1). Complete analyses of composites from the drill holes showed that the ore was very complex in character. It contained the above values in gold, silver, copper, and zinc, as well as large amounts of sulphur and iron, and traces of lead, arsenic, antimony, cobalt, and various other metals. Although the ore was obviously pyritic in character, pyritic smelting, the usual method of treating this class of ore, could not be used to beneficiate the ore with any reasonable expectation of making such a venture a financial success, since coke and coal landed at Flin Flon would be expensive, and siliceous flux was known to be scarce locally and low in grade. The property therefore lay idle until 1925.

Jan 1, 1935

By W. L. Stuewe

The Dominion Steel and Coal Corporation requires enormous quantities of bricks each year for its Sydney steel plant operations. Clay brick of all types are purchased, while silica brick is made in the Company&apos;s plant at Sydney. A description of this plant was given in a paper presented by H. B. Gillis and F. C. Morrison at the 1938 Annual General Meeting of the Institute. The rock used to make silica brick was for years obtained from a quarry at Leitches Creek, about eighteen miles from Sydney. Due to the gradual deterioration of this deposit, the Corporation was forced to look for other sources of supply. In 1945, the problem was presented to the Nova Scotia Department of Mines and, through the efforts of Dr. A. E. Cameron and Mr. J. P. Messervey, an examination was made of a silica-rock deposit some six miles northwest of Yarmouth, N.S. Preliminary samples proved satisfactory, and arrangements were made with the Department of Mines to ship to the steel plant at Sydney a fifty-ton car load for the purpose of further testing. Brick made from this sample shipment stood up very well in the furnaces. At the same time, two hundred and fifty tons of silica rock from a deposit at Lac Bouchette, Que., were purchased from the Industrial Silica Corporation, and brick made from this rock also was found suitable for our requirements. Comparative transportation costs, however, led to a decision to open the Yarmouth deposit. The silica rock, or quartzite, of this deposit outcrops at Chegoggin point along what is known as the &apos;Pembroke shore&apos;, a northerly trending section of the coast-line at the extreme southwest of the Province, in Yarmouth county. The country here is fairly flat, with elevation averaging about twenty feet above high tide, and is for the most part mantled by a growth of brush and some scrub trees, chiefly small fir. Bed-rock is generally concealed beneath three to four feet of clayey soil, but scattered outcrops of the quartzite indicated that a band of this rock, some 260 feet wide, extended inland in a northeasterly direction from Chegoggin point at least to Utleys lake, a distance of about three miles.

Jan 1, 1947

By Y. M. Shneerson, E. E. Zhmarin, E. M. Vigdorchik

One of the Gipronickel Institute activities is research and development of customized leaching technologies. The work is performed in several steps. Leaching kinetics are studied on a lab-scale according to a special procedure. Experimental data are processed using mathematical models of batch and continuous processes. Reliability of kinetic data and preliminary calculations is verified experimentally in laboratory reactors of various capacities. If necessary, certain parameters of the mathematical model are adjusted after pilot plant tests in continuous mode ( 4-reactor train, each with 25 L capacity). The specified kinetic characteristics along with the mathematical model are used for further development of industrial leaching technology.

Jan 1, 2005

By P. E. Fox, R. S. Cameron

"The QR gold deposit lies in the Cariboo plateau region of central British Columbia. The deposit was discovered in 1977 and since then a mineable reserve of 1.3 million tonnes grading 4.7 g/t Au has' been outlined in three separate zones. Soil sampling of glacial tills followed by diamond drilling of favourable host rocks proved to be key exploration techniques.The deposit is situated in the southern Quesnel terrane along the eastern fringe of the Intermontane Belt which here comprises a sequence of basic and intermediate volcanics and a series of stocks of alkaline affinity; generally diorite, monzonite and syenite. Hornfels and epidote-rich ferromagnesian exoskarn and sulphide-rich mantos have developed in a metamorphic aureole formed around a central diorite stock. Gold-rich zones lie along the outer periphery of the aureole where bodies of gold-bearing epidote-rich skarn and auriferous mantos rich in epidote and pyrite have formed in beds of calcareous tuffite lying at the top of a thick basaltic sequence. The deposit is regarded as' a subclass of gold skarn deposits. Diagnostic features are its association with alkalic intrusive rocks in a subvolcanic setting and the presence of oxidized, epidote-rich mineral assemblages.IntroductionThe QR gold deposit lies within the Cariboo plateau region of central British Columbia, 58 km southeast of Quesnel. The deposit, owned by Kinross Gold, was discovered during a regional reconnaissance program by Dome Exploration (Canada) Limited and Newconex Canadian Exploration in 1977. Considerable exploration and development has been done since that time. Mineable reserves of 1.3 million tonnes grading 4.7 g/t Au have been outlined to date in three zones."

Jan 1, 1995

By G. Guiglionda, A. Deschamps, F. De Geuser, M. Langille, B. J. Diak

"Increased demand for light-weighting in passenger vehicles has created a need for strong, light, ductile materials to be used in body-in-white applications. The AA6xxx-series of aluminum alloys are suitable candidates meeting most requirements but can fall short of the formability demands of designers, necessitating an understanding of what controls the formability in this alloy series. This work examines the effect of copper alloying in AA6xxx on the pre-ageing and natural ageing responses of the microstructure and mechanical properties. The changes in microstructure observed by differential scanning calorimetry and hardness testing are related to the work-hardening and strain-rate sensitivity parameters for these alloys measured by tensile testing. An observed asymmetry in the measured strain-rate sensitivity associated with increasing versus decreasing strain rate changes suggests that a different mechanism operates for the two conditions. It is postulated how this asymmetry in strain-rate sensitivity will impact the necking and ductility behaviour of these alloys.INTRODUCTION The widespread use of AA6xxx series alloys in the form of sheets has provided the need for a more thorough understanding of the complex interactions between composition, processing, resulting microstructure and ultimately, the mechanical properties of the alloys. Conventional industrial practices involve the production of rolled AA6xxx sheet (typically 1 mm thick) to be used for body-in-white (BIW) applications for auto body panels (Hirsch, 2004, 2014). The final metallurgical step prior to the shipment of these panels to manufacturers involves a solution heat treatment (SHT) reverting the ageing products of the alloys into solid solution and the product is then shipped to the customer. During this shipping time and while sheets are waiting to be used, the natural ageing (NA) process occurs whereby the strength of the alloys increases resulting in reduced formability. This can result in a product that is unable to meet the formability demands of the automotive manufacturer. As a result, industry has moved towards performing pre-ageing (PA) treatments to prolong the “shelf-life” of the material prior to it having insufficient formability. Once formed into BIW panels, the parts are then painted and subsequently undergo the paint curing heat treatment which consists of a short period of time at medium temperature, typically 20 minutes at 170–190°C. This short artificial ageing (AA) treatment, known as the paint bake (PB), provides additional strength and improved dent resistance for the material, but reduced formability. The PB result is strongly dependent on the PA treatment performed prior to the forming operation. Furthermore, the addition of copper (Cu) to a base Al-Mg-Si composition is known to increase the alloy’s strength. The goal of this work is to study the effect of Cu on strength, strain hardening, and strain-rate sensitivity (SRS) of these alloys, to understand the strength-formability compromise, for two separate heat treatment schedules; one including and one excluding the PA treatment, both followed by NA."

Jan 1, 2018

By X. -G. Chen, E. M. Elgallad

Direct chill (DC) cast ingot plates of 2xxx alloys have been increasingly used for large mold applications in the plastics and automotive industries. A novel heat treatment practice for Al-3%Cu-1%Mg DC cast ingot plates has been developed, involving solution treatment, furnace cooling to the desired aging temperature and holding for appropriate time at the aging temperature. The mechanical properties of the plates were studied for different combinations of aging temperature and time, using hardness measurements and tensile testing. The evolution of the strengthening precipitates was investigated under different cooling rates corresponding to cold water quenching, still-air cooling and furnace cooling, using electrical conductivity measurements. The results showed that by applying the novel heat treatment, the cast ingot plates could provide a wide range of combinations of strength and ductility satisfying the design specifications of large molds. This, in turn, offers a practical solution for the fabrication of extremely large DC cast plates combining between good mechanical properties and low levels of residual stress using the shortest possible heat treating cycle.

Jan 1, 2015

"THE OTTAWA BRANCH, CIM, each year holds a symposium on a subject of topical interest. The symposium this year was on Canada's Offshore Mineral Resources, at which papers were presented by: Dr. Donald G. Crosby, chief, Resource Administration Di-vision, Department of Energy, Mines and Resources, Ottawa; John A. Beesley, head, Legal Division, Department of External Affairs, Ottawa; and David W. Smith, man-ager, offshore exploration and production, Shell Canada Limited, Calgary. Because of the interest which this topic holds for our members, and because of the wealth and significance of information presented, the three papers -representing the first comprehensive review of our offshore resources -are reproduced herewith. The opening remarks of the Chairman, Dr. F. K. North, Professor of Geology, Carleton University, are also recorded, together with a few of the questions asked by the large attending audience. The symposium was held February 13th, and was organized by Dr. W. M. Tupper, chairman of the Branch Program Commit-tee. Differences in the extent of the continental shelf will be noted in the papers. These differences are related to slightly different definitions of the continental shelf by the authors."

Jan 1, 1969

By J. M. Wetherill

"This paper presents the results of an investigation into the level of radon, as against the natural background, at the Vicary Creek coal mine in Alberta. The concentrations of radon and daughter products detected in the mine were considered to be insignificantly higher than the concentrations of naturally occurring radon and thus do not constitute a health hazard to the miners.INTRODUCTIONTHE HIGH INCIDENCE OF LUNG CANCER among miners exposed to radon was established some thirty years ago. The presence of this gas in mines is primarily associated with pitchblende extraction operations, al-though coal contains detectab`e quantities of U30s. A previous study bas shown that coal from southwestern Alberta (Exshaw and Banff) contains lower than average concentrations of this element (1).As part of a general investigation into the occupational health environment of coal miners in Alberta, field measurements were made to establish the level of radon and to investigate the natural background radiation in the Vicary Creek coal mine, located some 16 miles north of Coleman, Alberta, on the easternmost slopes of the Rocky Mountains."

Jan 1, 1968

By B. S. W. Buffam

Introduction The development of uranium deposits is a relatively recent phase of mining in Canada. To date, the only producer of uranium ores on a commercial scale has been the Port Radium mine on Great Bear lake, N.W.T. However, with.-in the past few years intensive prospecting has been carried on throughout Canada and many occurrences of uranium-bearing minerals have been discovered. Eldorado has been active in the search for and the exploration of uranium deposits in Canada for a longer period than any other company and has, therefore, accumulated a considerable fund of information, especially about occurrences in Saskatchewan and in the Northwest Territories along the western fringe of the Precambrian Shield. The Company has also had experience in the underground operation, and in the mining, of uranium ores at Port Radium. During the past year or so many requests have been received from the prospecting and mining fraternity for information and guidance regarding the development of the many new uranium discoveries that have been made in Canada. Assistance by Eldorado is freely given whenever possible and this paper is presented to supplement the private discussions and to provide as wide a distribution as possible of the data acquired by Eldorado.

Jan 1, 1951

By P. Maltby

"Smelter Feed Preparation Falconbridge Nickel Mines Limited, Sudbury Operations, operate 4 mills and a smelter to produce Bessemer Ni-Cu matte for refining in Norway. Approximately 1400 tons of Ni-Cu concentrate are produced daily which are dried from a filter cake containing 14% moisture to 7.5% moisture pellets. Concentrate drying is done by 4 rotary dryers as shown in the 'Dryer Performance Data' at four separate locations. The dryers all form part of the feed preparation stage prior to sintering.The rate at which concentrate can be produced through the Sinter Plant largely depends on the quality of the dried product which makes up the feed. A feed consisting of mostly hardened pellets will sinter much faster than a feed which consists of broken pellets and dust. Dryer products require:1. Good green strength to survive shipment and handling.2. Correct moisture content.3. Sizing within a range ideally from 1/4"" to 10 mesh in diameter.Dryer performance data is shown in Table 1. Capital costs between the two types of dryers are comparable with the Roto-Louvre producing generally a larger better-formed pellet. Dryer feeds differ in that at both Hardy and Fecunis, Ni-Cu concentrate filter cake is the only feed while at the Falconbridge slurry plant the dryer feed can consist of up to 10% by weight of smelter flue dust resulting in a combined concentrate-dust pellet for feeding to the Sinter Plant. To the Falconbridge Sinter Plant dryer, dust and limestone are added for the smelting process in addition to Ni-Cu concentrate."

Jan 1, 1972

By G. H. K. Pearse, R. P. Taylor

The Big Whopper, one of only four giant economic rare metal pegmatites worldwide, is set to become a producer of the highly valued lithium mineral petalite (LiAlSi4O10) used in glass, ceramics and the specialty glass-ceramics familiar as Corningware® and the new ceramic stovetops. The deposit has a strike length of 1.5 km, a width of up to 80 m and a resource, open in all directions, of 11.6 Mt, grading 25% petalite. It is amenable to open pit mining and Avalon Ventures Ltd. holds a patent on a flotation process that produces an exceptional quality petalite product. The project will also produce: superb quality Na-feldspar which, too, finds use in glass and ceramics; the unusual Rb- K-feldspar for high voltage porcelain insulators; tantalum, in high demand for electronics; lepidolite, an ore of rubidium; and mica and tin. A positive prefeasibility study has been completed and it remains only to undertake bulk sampling and a full feasibility study.

Jan 1, 2001

By Navid Bahrani

The grain-based model (GBM) has resolved the difficulty of matching both the directtension (sc) and unconfined-compressive (st strengths of typical brittle rock by providing a synthetic material that mimics deformable, breakable polygonal grains cemented along their adjoining sides with deformable, breakable interfaces modeled as smooth-joint contacts. In this paper, a GBM utilizing a parallel-bonded base material is calibrated to match both st and sc of Lac du Bonnet granite and then used to simulate a Brazilian test. The Brazilian strength (sB) is slightly overestimated and the failure mode includes ductile post-peak response that is not representative of what occurs in laboratory Brazilian tests. By reducing the grain tensile strength, grain failure occurs during the Brazilian test and a more realistic failure mode that includes brittle post-peak response is obtained. However, the unconfinedcompressive strength of the modified material is too low. Sensitivity analysis on the grain and grainboundary strength properties demonstrates that the grain tensile strength controls the sB/sc ratio. Because the grain strength is controlled by the parallel-bond properties and the lowest achievable st/sc ratio in a parallel-bonded material is ~0.25, it is concluded thatsc, st and sB for a typical brittle rock cannot be matched with a GBM that utilizes a parallel-bonded base material.

Jun 1, 2012