Search Documents

By T. Senga, T. Namihira, S. Terada, S. Owada

"Electrical disintegration (ED) has been well known as a good comminution method to improve liberation of compositional phases because it was reported that electron avalanche could occur preferentially at phase boundary. But the detailed mechanism of the ED has been still not known. This paper describes the results of ED experiments using synthetic binary sample, copper/resin, under the conditions of various distance between electrodes, and discusses the energy distribution in the three kinds of phenomena in the ED process, which are(1) streamer progression in water, (2) electron avalanche in water, and (3) electron avalanche in solid sample, by measuring current and voltage with elapsed time. Then, it has been found that the energy distribution in the phenomenon (1) is quite low and that the distribution in the phenomenon(2) had a considerably large compared with that in the(3), which indicates that the shockwave generated in water could contribute much to the sample breakage.INTRODUCTIONElectrical disintegration (ED) has been well known as a specific comminution technology which enhanced selective breakage at phase boundary and lead to a good liberation among compositional phases1-6),but the detailed mechanism has not been clarified yet. This study describes energy distribution among the phenomena in the ED process by using a synthetic binary sample, copper/resin, the phenomena of which are (1) streamer progression in water, (2) electron avalanche and shockwave generation in water and (3) electron avalanche in solid sample usually at phase boundary. The energy distribution could be calculated from ED experiments and from voltage-current changes between electrodes as a function of elapsed time.SAMPLE AND EXPERIMENTALSampleThe sample used in this paper was a synthetic binary solid of copper/resin as shown in Figure1.Cut and polished pure copper lump was put into silicone mold and melted epoxy resin was poured into it and cooled, then, finally the binary sample was polished and molded in the form of 10 mm * 10 mm * 10 mm."

Jan 1, 2017

By Zhiqing Zhang, Changyun Chen, Qing Liu, Lin Lin, Zhihong Jia, Guangjie Huang, Lipeng Ding

The effect of interrupted quenching (IQ) treatments on natural aging and bake hardening response of Al-Mg-Si alloy was investigated by hardness measurements, tensile test, differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). The results show that interrupted quenching at 100oC could effectively suppress natural aging and improve bake hardening response. The optimized interrupted quenching treatment is 100oC for 45min, which gives the alloy a relatively low T4 temper strength and higher bake hardening response. The formation of highly dense cluster(2) during the interrupted quenching could be the reason for suppressing the natural aging and accelerating the precipitation of ß? phase during the paint bake treatment. In addition, interrupted quenching at higher temperature (170oC) results in unfavorable properties in both T4 temper and paint bake treatment. The formation of large precipitates is responsible for these undesired effects.

Jan 1, 2015

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber plant was recently completed at an existing facility, in order to treat the sulphur dioxide off-gas emitted from rotary kilns. Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong operational readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.INTRODUCTIONCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Quebec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary byproductof the process.Fresh hydrated lime and CDS residue is captured by the dust collection system and is re-circulated to the CDS via a fluidised transport system. Clean off-gas passes through the dust-collection system and is then sent to the atmosphere by a single exhaust fan.The CDS residue purged from the system is combined with the dust collected from the kiln offgas system and this mixture is wetted in the already exiting agglomeration system, to minimize dust generation during handling, and then sent to disposal."

Jan 1, 2016

By W. R. Dodge

THE growth and development of the assay department of the Hollinger Consolidated Gold Mines, Limited, is a similar story to that of the mine itself. As the mine developed and enlarged, so also increased the demands upon this department, necessitating an increase of capacity for fire assaying and a widening of the scope of work to include chemical analysis, metallurgical tests, research, and screen analysis. The yearly total of determinations, taking an average for the past six years, is approximately 350,000. The major portion of this figure represents fire assaying for gold and silver, being approximately 950 fire assays per day. The assay department occupies the ground floor of the administration building and covers approximately 4,000 square feet of floor space. Ready access is had by motor truck and electric railway for the delivery of samples and the removal of crushed rock and rubbish. The combined weight of all sample rejects amounts to about 5,000 lb. per day, which is sent to the mill bins. There are six departments, each occupying a separate room-grinder room, fluxing room, furnace room, parting room, weighing room, and flux-mixing and storage room.

Jan 1, 1931

By L. Narhi, K. Haavanlammi

"Approximately two thirds of annual nickel production is used as a raw material in the making of stainless steel, and about 60% of these nickel products are in the form of metallic nickel such as nickel cathode or briquettes. In the stainless-steel production process nickel is blended with iron and chrome-based raw materials, and metallic nickel is typically only required for final steel fine-tuning. Outotec offers a new FeCrNi technology to enhance the nickel value chain for stainless steel producers. This involves the use of an HPAL-based intermediate nickel product (e.g., mixed hydroxides or NiO) as raw material in the Outotec FeCrNi process, for the production of a FeCrNi Master Alloy. The new process, designated as the FeCrNi process, offers multiple benefits compared to existing technologies such as: higher tolerance for impurities in the HPAL intermediate product, avoiding the need for further nickel refining, and the improved recovery of all metals in the FeCr process. The complete new FeCrNi value chain is based on proven technologies such as HPAL and the Outotec FeCr-process. This new innovative and promising value chain offers improved efficiencies for the HPAL based nickel production process combined with excellent sustainability aspects.INTRODUCTION In today’s global economy there is a constant need to improve the efficiency and sustainability of the metals production. The requirements for modern metal refining are tightening and cost efficient, safe and sustainable operation is the precondition for all investment. Outotec is offering now a novel way to combine FeCr and Nickel production to create a completely new value chain to source nickel to stainless steel. BACKGROUND Nickel The current nickel mine production is in the level of 2,000 tons annually and it is split 44% from sulphide based deposits and 56% from laterite deposits (Figure 1). Most (40%) of the nickel is refined to pure nickel metal whereas other products are FeNi (19%) and Nickel Pig Iron NPI (20%) (Roskill). The remaining part, roughly 21%, is nickel chemicals and intermediates. Most of the new investments in nickel are in the direct shipping of laterite to produce nickel pig iron. HPAL process is considered in few projects but no major HPAL projects have been started since the Ambatovy plant in Madagascar. Ambatovy reached the commercial production in 2014. The main primary nickel used is stainless steel manufacturing. In the year 2016 about 68% (~1,360 kt) of primary nickel production was used in stainless steel."

Jan 1, 2017

By Jakob Janzen

This paper demonstrates that the introduction of a Battery Energy Storage System (BESS) into an isolated diesel generator based grid has the potential to reduce the electricity cost and deliver a good return on investment. Energy storage also allows for increased renewable energy penetration, into the isolated grid, that further reduces the electricity cost. The isolated power system studied includes several diesel generators of different sizes. The typical operating pattern is for the generators to be run at 80% to 85% of their power rating to deal with load fluctuations. Operating the diesel generators near their full power rating, however, improves their efficiency, in this case, while the frequency and load control can be carried out by the BESS. Operating the diesel generators near their full power rating reduces the number of generators which need to be operating to support a given load. As a result, the improved efficiency of the diesel generators and reduced maintenance cost, for operating fewer machines, are the reason for the savings.

Aug 1, 2013

By Hao Zhang

Site inspection is an important component of safety management system. In current practices, the inspectors evaluate the safety condition on a construction site with the assistance of a standardised checklist. However, the checklist emphasizes on evaluating the implementation of safety management system, but provides limited task-specific check items for assessing whether the individual construction tasks are conducted under safe condition and in a safe manner. To address this issue, the research presented in this paper aims to provide safety practitioners with comprehensive and taskspecific safety information to promote effective risk identification and facilitate strategic risk control during site inspection. Specifically, this research first builds a project-specific safety information database, which stores potential risks and control measures for each construction task. The research team then develops a mobile decision support tool to retrieve information from the database and support safer decision-making on site. The tool supports users in two ways: one is to provide daily risk checklists and risk control strategies to guide step-by-step inspection alongside the project schedule; the other is to let users input any safety-related keywords during the safety inspection process and the tool returns relevant safety information by applying text mining algorithms. It is ongoing research. This paper presents an overall research framework and discusses the progress in developing safety database and data retrieval concepts. The outcome of the project will help enhance safety management practices and reduce possible risky working conditions on a construction site.

Aug 1, 2013

By P. Hansman

"Place Dome Canada's Detour Lake Mine is a low-grade gold producer located in northeastern Ontario. Production is targeted for 2850 tonnes of ore per day. As reserves and mining areas continued to be found below and far to the west of the shaft (Fig. 1), it became necessary to review and upgrade the materials handling facilities. This paper deals with the selection, design and construction of an underground crusher and conveyor system capable of handling up to 450 tonnes per hour from the lowest existing level in the mine.BackgroundThe Detour Lake mine site is accessed via secondary Highway 652 which runs northeast out of Cochrane, Ontario. The road consists of 200 Ian of hard top followed by 100 Ian of well maintained gravel to the mine site. A 1500 m airstrip is maintained at the mine site for emergency use. Prior to 1991, the workforce was flown to and from the mine site. Crews were now bused to the site from Timmins. Remnants of a winter road exist to the southeast which at one time ended in La Sarre, Quebec. This was the route used to haul bulk items during the construction period and early production years.A town site has not been established at the site for the current operations. Instead, a rotational scheme is being utilized whereby most personnel will work seven days on site followed by seven days off site. For some employees, however, the work week is termed as a four/three schedule where they work 42 hours between Monday at 10:00 a.m. and Thursday at 4:00 p.m. with the following three days off. All surface employees and maintenance employees underground work 12-hour shifts. All underground employees work a lOV2-hour shift. Supervisors work a similar schedule as their crews, however, other staff may overlap their rotation during the week.A five-compartment shaft was sunk in 1984 from surface to the 610 m elevation. Shaft stations were established at the 120 m, 260 m, 360 m, 460 m, and 560 m levels. The cage compartment consists of a single deck, 4O-man cage in balance with a counterweight. The cage hoist is an Ingersoll-Rand 10H and is regulated to travel at 4.1 m/s. Two 9 t skips operate in balance at a travel speed of 7.1 mls. The skip hoist is a 3.05 m drum Nordberg. Both hoists are automated to function without a hoistman during normal skipping and cage service runs."

Jan 1, 1995

By J. A. Maritz

"The Hedley and Grant formulation for pillar strength has been widely adopted by the South Africa hard rock mining industry. Today, some forty year later, this formula still provides the foundation for pillar strength calculations when designing for stability and utilising pillars in mine layouts. Various mine specific back analyses were conducted to adjust the equation parameters based on underground observations of failed pillars and comparing to the pillar stresses calculated using numerical models. In all these instances, the influence of shear stresses was ignored. The key to more representative pillar strength estimation is a better understanding of the pillar loading environment.In this paper, special mining cases are evaluated and the existence of shear stresses on the pillar loading environment is illustrated. By revisiting some back analysis data for optimisation of the equation parameters, recommendations were made in respect of the influence of the shear stress component and on how this should be considered in determining the pillar strength.INTRODUCTIONCommon practice on flat dipping, shallow and intermediate depth ore deposits in the South African hard rock and coal mining industry is to exploit the mineral resource using a room-and-pillar layout. The design methodology is mainly based on a Factor of Safety (FoS) approach, where the strength of the pillar is compared to the effective load on the pillar. In these environments, FoS values of 1.6 are applied as it was found to correspond to a probability of failure in coal mines of 0.001. As discussed by Ryder and Jager (2002) page 279: “For lack of anything else more substantial, the figure of 1.6 is generally used in hard rock pillar design in South Africa”. Dependant on the designed purpose of the pillar, the FoS might be selected as high as 2.0 where long term stability is required. The factors directly influencing the FoS include the pillar height (which is linked to the mining height), effective pillar width, a rock-strength factor and extraction ratio."

Jan 1, 2015

By T. G. Edgeworth

Some of the historical background of the industry is reviewed, with reference to the different types of reduction cells in use for aluminum smelting. Factors to be considered in cell des1gn involve capital, power, and operating costs. The trend is apparently toward larger cells. The industry is studying new construction materials for cell linings, as well as alternate electrolyte compositions and other design changes which will improve productivity and energy efficiency. The aluminum smelting activity in other countries is briefly reviewed. TODA Y'S industrial production of aluminum is still based on the simultaneous discoveries made in 1886 by Charles Martin Hall in Ohio, and Paul Heroult in France. Up to that date, only about 50 tons of aluminum had been produced in the world, and the price at that time was about $5 per pound. Sucl1 figures must be contrasted with the present world aluminum smelting capacity of over five mil-lion tons per year, and a price of about 25 cents per pound.

Jan 1, 1962

By J. G. Pharoah

Over the last two decades a variety of models for solid oxide fuel cells (SOFCs) have emerged ranging from one dimensional (1-D) to 3-D models, from steady-state to transient models; single- and half-cell and entire stack models. A majority of these models have focused either on the transport processes or on the chemical/electrochemical processes. The approach taken by our research group is to develop a comprehensive SOFC model framework based on the considerations of detailed electrochemical reaction mechanism and by accounting for complex transport processes occurring in the porous media at the micro-scale level. In this paper, we review the state-of-the-art in SOFC modeling and identify the existing gaps that need to be filled in.

Jan 1, 2005

By M. L. Jeremic

"The syngenetic and epigenetic mechanics of sedimentation and deformation of coal seams resulted in various types of internal structure, as listed below:TYPE I-massive structure with evenly distributed coal constituencies of integrated mechanical properties.TYPE II-broad-banded structure, with bright and dull coal bands of differential mechanical properties.TYPE III-heterogeneous structure, with sheared coal bands and partings of sectional mechanical properties.TYPE IV-contortional structure, with refolded coal layers and deteriorated mechanical properties.TYPE V-porous structure of orogenically crushed and pulverized coal, with disintegrated mechanical properties.The study suggests criteria for the estimation of coal seam internal structure (gamma-gamma density log and cracks density log), which might be related to the evaluation of strata stability and coal mineability.IntroductionIt is common knowledge that coal seams have various internal structures due to different syngenetic and epigenetic events. Investigations of the internal structure of coal seams have been carried out in the coal fields of Western Canada, as follows: geological field studies of coal-bearing strata;?,geophysical borehole surveying studies;?,geological borehole logging and crack density;?,underground phenomenological studies of mine structure;?,chemical coal analysis; and?,mechanical testing of coal samples.These investigations eliminated a large number of criteria previously established for the estimation of coal seam internal structure and indicated that, from an engineering point of view, only two of them are sufficient:(I) density of seam profile (inferred from gamma-gamma log);(2) density of crack s (inferred from geological log).On the basis of these criteria, five main structural types of coal seams have been classified, which might be related to mechanics of deformation and ' failure of mine structures."

Jan 1, 1982

By G. Reuben Yourt

This paper consists of two main parts. The first, under the heading Preparations, deals with suggested preparations to be carried out in advance so that loss of life might be prevented should a fire occur. The second part, under the heading Fire Procedure, deals with actual organized procedure to be followed for the preservation of life if and when a fire occurs. The writer realizes that these preparations and procedures may be to some extent applicable to only a few mines with a relatively simple vein system and that each mine would need to formulate a procedure to conform to its own particular conditions, scope, and degree of complexity. Preparations 1. - Ventilation Control The objective in ventilation control in the event of a tire underground is to keep the travelways, through which men must pass to reach surface, supplied with air not deficient in oxygen and free from gases and smoke. Without some control of the volume and direction of the main air currents flowing through the mine, the success of removing men to surface might be seriously hampered. ? This control is achieved by means of mechanical ventilation forcing air through desired airways and workings with the assistance of doors to regulate the volume and direction of the air flow. In connection with fans and doors, the possibility of short-circuiting should always be taken into consideration, as it can often nullify the value of a fan and possibly trap men in dangerous atmosphere if the short-circuiting involves the fire area. Main fans are often installed so that they can be reversed in a short time. However, fans should not be reversed unless this is found absolutely essential by those in authority. Misjudgment in this respect could cause the loss of life to men who might naturally take refuge in what they believe by experience to be a fresh air stream. Another precaution to be taken is to see that doors in airways are fastened in a fixed position so that they cannot be sucked or blown open when the fan is reversed, otherwise short-circuiting could possibly render the fan useless.

Jan 1, 1947

By Unknown

Diesel locomotives for underground haulage have been used in coal mines in Continental Europe for twenty-five years or more. In Great Britain, it was not until 1935 that permission was granted to use them in gassy coal mines, but since that time they have been employed in increasing numbers both in gassy and non-gassy coal mines and in metal mines. Their use underground in coal mines in the United States is still prohibited and the same was the case in Canada until 1946, when permission was granted to operate a Diesel underground in the Adanac mine of West Canadian Collieries, Limited, at Bellevue, Alberta. The locomotive used here is a 50 h.p. Hunslet Mark II. More recently, a 100 h.p. Diesel was placed in operation for underground haulage at No. 18 Colliery of the Dominion Steel and Coal Corporation, in the Sydney coalfield, N. S. Thus, on this continent, Canada has been a pioneer in the use of these locomotives underground in coal mines and there is no doubt that more and more of them will be employed as time goes on. We feel, therefore, that the following notes concerning their design and performance, which we have received from the High Commissioner for the United Kingdom, will be of interest to our members.

Jan 1, 1949

By A. Plugatyr, C. P. Baxter

"Bessemer matte iron content is a critical process parameter that needs to be closely monitored and controlled in order to achieve optimal Ni/Cu smelter returns. Current process control practices during Ni/Cu converting often rely on visual observations and typically involve matte sampling to confirm that target composition was reached. A high-level techno-economic analysis study was carried out to evaluate potential direct benefits of advanced process control during the final stages of Ni/Cu matte converting. The results indicate that the magnitude of direct benefits will largely depend on matte iron control practices already implemented as well as matte iron set point. Preliminary assessment suggests that under the assumptions used in this study, implementation of advanced process control can potentially result in additional revenues ranging from several hundreds of thousands to tens of millions of US dollars per year per converter producing about 200 tonnes of Bessemer matte per day based on Ni, Cu, and Co metal recoveries alone.INTRODUCTION Real-time measurement of molten metal elemental composition, arguably, remains one of the key unresolved issues impeding full automation and real-time optimization of pyrometallurgical operations in different industrial areas, including non-ferrous metals and ferro-alloys. In particular, current process control practices during Ni/Cu matte converting often rely on visual observations and typically involve matte sampling in order to confirm target matte composition. In addition to being time consuming, this approach relies heavily on operator experience and diligence, and, therefore, requires continuous performance and quality control efforts. For instance, the need to improve quality of the Bessemer matte (BM) at the Copper Cliff smelter has prompted an impressive staff engagement and training campaign that was carried out by Vale’s team in the late 2000’s (Zanini, Wong, & Cooke, 2012). This training exercise was executed to address the compounded effect of several operational challenges, namely demand for higher throughputs, changes in the feed concentrate composition, increased feed variability, loss of process knowledge and expertise due to retirement, as well as lack of a comprehensive approach to improving the overall performance of the flowsheet rather than meeting production targets for intermediate products. Although the campaign was very successful and has resulted in significant improvements in the Bessemer matte quality, it has also highlighted the need to move away from “the-art-of-converting” and develop analytical tools that would enable real-time process monitoring."

Jan 1, 2018

By V. T. Panayotov, M. I. Panayotova

Wastewater from mining and mineral processing activities is often polluted by anion forming metals, such as molybdenum and chromium. Low cost materials, including zeolites, are studied for removing heavy metals from wastewater. It is widely accepted that natural zeolites are not effective in removing metals in anionic form. The paper presents study on use of metal modified natural clinoptilolite to remove Mo (VI) and Cr (VI) ions from model soft wastewater. Modification with Pb, Fe(III), Zn and Ba increases clinoptilolite uptake capacity with respect to Mo(VI) at low pH values of the water subjected to treatment, the efficiency decreasing in the order Pb > Fe(III) > Zn > Ba. Only lead-modified clinoptilolite shows high uptake of Mo(VI) in acidic, neutral and slightly alkaline conditions. Modification with Pb, Ba and Fe(III) increases zeolite uptake capacity with respect to Cr(VI) from neutral water. The effectiveness of Ba-modified zeolite decreases in slightly acidic water. Over 90 % uptake of initially available Cr(VI) is achieved by lead-modified clinoptilolite both under neutral and slightly acidic conditions. Increasing the initial pollutant concentrations increases the removed amount both of Cr(VI) and Mo(VI) for Pb-modified clinoptilolite. The findings could be a basis for using the natural clinoptilolite to remove in consecutive steps: firstly Pb(II) and/or Fe(III) ions and then loaded zeolite to be used for Mo (VI) and/or Cr(VI) removal. The kinetics of Mo(VI) uptake by CL-Ba, CL-Fe(III), CL-Pb, and CL-Zn is best described by the pseudo-first order kinetic equation. The kinetics of Cr(VI) removal by CL-Ba, CL-Fe (II), CL-Fe (III) and CL-Zn is best described by the pseudo-first order kinetic equation. Kinetics of Cr(VI) removal by CL-Pb obeys the equation for the first order irreversible reactions. Finding way to remove anions-pollutants from the mineral processing wastewater will render this industry more environmentally friendly and socially acceptable.

Jan 1, 2016

By Radford B. Langston

Mining Methods Majority of Production Ramp and Fill at Stillwater, Sub-level Becoming More Important Production at East Boulder from Sub-level l Majority JM REEF ROCK TYPES NORITE - plagioclase and bronzite cumulate GABBRONORITE - plagioclase, augite, and bronzite cumulate TROCTOLITE - plagioclase and olivine cumulate ANORTHOSITE - plagioclase cumulate PERIDOTITE - olivine cumulate

May 1, 2002

By E. E. Mueser

As Mr. Lundberg has already ably covered the theory of various methods of electrical prospecting, I shall confine my remarks to a consideration of the features which must obtain in an electrical prospecting method in order that it may be useful from a practical standpoint. These remarks I shall make with particular reference to the Elbof method. The successful application of all these methods rests, in the first place, upon the possibility of correlating theory, or empirically established facts, with the field data. Their practical usefulness, however, requires that the technique of making the field observations, and the procedure itself, be such that the method may be applied to large areas, under normal average conditions. The method, therefore, should not involve excessive preliminary labour costs to prepare the ground for actual prospecting work, nor should the prospecting work itself be so slow that its cost, when applied to extensive areas, becomes prohibitive. Moreover, it should be possible to apply the method even under difficult terrain conditions, such as rough topography and dense vegetation. It may be said of most of the methods referred to in the preceding paper, that, while they are interesting and theoretically sound, they fail to meet such practical requirements as I have outlined.

Jan 1, 1926

By A. L. Craven, J. P. L. Bacharach, D. B. Stewart

"Inert gas use for underground mine fir e control is a well-established mature technology in some parts of the world. This paper reviews three candidate inert gases and describes three case histories where inert gas fire-fighting technology was used in actual underground fires.IntroductionInerting is the introduction of an inert gas into an atmosphere in contact with a fire to reduce the level of oxygen and hence the intensity of the fire 10 the point of extinction. The benefits of inerting include:a. Reduced Explosion HazardBy displacing oxygen from the atmosphere surrounding the fire the risk of secondary gas explosions is reduced. For example, simple methane-air mixtures at standard temperature and pressure are non-explosive below 12% oxygen. In actual mine fires, combustible gases may include hydrogen and carbon monoxide as well as methane. Such gases are also rendered non-explosive with oxygen removal to below 40/0. Fuel-rich oxygen-deficient mixtures can however be made explosive through dilution with air. Such dilution can occur downwind of the fire. It is also important to remember that the atmosphere in a sealed-off fire zone is rarely homogenous.b. Reduced Fire Intensity and SpreadIn a fire zone the initial combustion may well set alight materials surrounding the fire. Inerting can reduce the intensity and spread of secondary combustion and can cool the area surrounding the fire zone after the fire itself has been extinguished.c. Reduced Air LeakageLeakage of air into sealed areas in excess of the natural leakage may be reduced either by introducing inert gas into the leakage paths to replace air or by pressure balancing seals and providing a chamber of nitrogen on the outbye side of the seals. Both methods assist in the reduction of the intensity of combustion and hasten oxygen starvation."

Jan 1, 1986

By G. Granata, C. Tokoro, T. Kato

"The goal of this study was to evaluate the effectiveness of mechanochemical activation by planetary milling as method to enhance the recovery of cerium from rare earth ores. For this purpose, a weathered ore was first ground by planetary milling and then leached by sulfuric acid. The influence of planetary milling was investigated by assisting the experiments with X-ray absorption fine structure (XAFS) in cerium LIII-edge and inductively coupled plasma spectrometry to measure the concentration of cerium dissolved by leaching. Results showed that, by increasing the grinding time, although the particle size of the specimen increased due to agglomeration, the recovery of cerium significantly increased. This finding clearly indicated that a smaller particle size actually hinders the recovery of cerium. In particular, XAFS analysis revealed that the longer the grinding time, the more tetravalent cerium could be converted into trivalent cerium and such conversion, also called mechanochemical reaction was beneficial to the recovery of cerium. Based on the obtained results, it was confirmed that approximately 70% of cerium could be recovered by mechanochemically activated leaching of rare earth ores.INTRODUCTION Rare earth elements (REEs) are a group of 17 chemically similar metallic elements comprising lanthanides, scandium and yttrium. Since REEs have various unique physical and/or chemical properties, they have become essential materials for advanced application (Adachi, 2015). REEs used in industry are usually supplied as rare earth minerals. In the last decades, flotation, gravity separation, magnetic separation and leaching have been widely applied to recovery of REEs from rare earth minerals like monazite (Archana, Rekha, Manis, Jitendra, & Jin, 2015). Among these operations, leaching has been widely studied in the recent years to improve the state of the art (Archana, Rekha, Manis, Jitendra, & Jin, 2015; Xiao, Feng, Huang, Huang, Chen, Liu, Wang, & Long, 2016; Farzaneh, Fereshteh, & Ahmad, 2017). Aiming to enhance recovery of REEs from rare earth minerals, a possible advancement of leaching technology could be the mechanochemically activation of the ore by high-intensity milling (Alorro, 2016). In the mechanochemical activation, an improvement of the leaching performances can be achieved through high-intensity milling operations which result into a dramatic decrease of the mineral particle size with a consequent improvement of the physical kinetics of leaching. Furthermore, the high mechanical energy provided to the sample during milling can determine the rupture of the crystal structure of the mineral, thereby transforming it into a more leachable form."

Jan 1, 2017