Search Documents

By Mohamad H. Hussein

A minipile system was employed in underpinning a historical structure in Florida. The existing structure is founded on shallow foundations. Subsurface conditions at the project site consist of deep organic deposits interbedded with loose sand and silty sand. A minipile foundation system was deemed the most appropriate underpinning corrective measure for the already badly cracked structure. A total of 68 minipiles, 3.5 inch OD and 0.25 inch wall thickness closed-ended concrete-filled steel pipes, were installed to depths varying from 55 to 175 feet. Installation was accomplished with a pile driving hammer having a rated energy of 1 kip-ft. Highest required pile design load was 15 kips. Conventional static and wave equation analyses were performed to establish preliminary pile lengths, to assess pile drivability and establish driving resistance criteria. Dynamic pile testing using the Pile Driving Analyzer was conducted on six of the production piles. This paper describes geotechnical design considerations, installation procedures, and dynamic field monitoring. This case represents unique applications of pile dynamic testing and such slender, very long minipiles in compressible soils.

Jan 1, 1993

By Lance Helwirg

New high and low double outfall bridge structures for a juvenile fish bypass system have been constructed on the Washington Shore approximately two miles downstream from the Bonneville Dam on the Columbia River. The high and low outfalls each extend approximately 400 feet into the river from the Washington shore and are designed to release juvenile salmon into the river at above-water discharge elevations for improved survival rates. The two outfall structures include post-tensioned concrete double box flume girders approximately 7 feet high by 13 feet wide, which will be submerged in river flows as high as 15 feet per second. Each of the 6 offshore foundation piers is composed of a single 10-foot diameter reinforced concrete drilled shaft with a permanent steel casing embedded into the river bottom approximately 100 feet. Challenging outfall design conditions included designing the entire structures to be submerged for long periods of time in 15-feet-per-second river water flow with a 60-foot cantilever at the end of each outfall, and with the superstructure 70 to 80 feet above the river bottom. Figures 1-1,1-2, and 1-3 show the high and low outfall structure overhead photos and elevation view.

Jan 1, 2001

By Rick Deschamps, Amanda Blank, Matthew W. Drewek, Michael P. Walker

The Prairie du Sac Dam, located on the Wisconsin River, northwest of Madison, Wisconsin, was constructed 1912-1914. The spillway is an Ambursen-type, consisting of a series timber pile supported pier and buttress walls and rollway slab. The timber piles supporting the spillway, numbering approximately 5,000, have deteriorated, and the spillway structure was underpinned with over 700 micropiles as part of a design-build construction project. The underpinning micropiles needed to be arranged to avoid interferences with the existing timber piles, requiring the micropiles to be installed in the open spaces between the piers and buttresses. Inevitably, the installation of the new micropiles encountered obstructions, including existing timber piles out of alignment, as well as timber piles used to support the original construction activities and sheet pile used to control water during the original construction. This paper discusses using finite element analysis to model the spillway structure to estimate the vertical and horizontal stiffness with an extensive sensitivity analysis was performed during the design phase to account for anticipated construction challenges and potential variations in the underpinning performance. The inherent rigidity of the spillway structure allowed for load distribution to the underpinning system even when new micropiles needed to be re-located and aligned to avoid interferences with existing timber piles and other abandoned foundation elements dating back to original construction.

Sep 8, 2021

By William H. Walton, Joel Dellaria, Jeffrey R. Hill

The City of Chicago has a world-renowned skyline and is known for its provocative architecture. The subsurface conditions in the city have allowed for construction of these significant structures. The skyline is supported on caissons as they are called in Chicago or drilled shafts in other locations. Despite the significant strides the industry has made in advancing the drilled shaft, the use of other specialty geotechnical construction techniques like micropiles has not been overlooked in Chicago and the surrounding areas. Micropiles have been utilized to underpin famous existing historic structures like Orchestra Hall any many others. Engineers have used 200 to 600 kip micropiles to underpin compromised, inadequate, or damaged caissons. The paper will discuss the use of drilled shafts, micropiles, and ground improvement over the last 30 years in Chicago using a curated collection of case histories. It will also examine advancing the industry beyond its current technical limitations using these techniques. INTRODUCTION 20,000 years ago, glaciers from the Chicago region left behind sheets of glacial clay till underlain by dense, over consolidated glacial till below: limestone bedrock, found about 100 ft below street level. An unusual feature in this profile is the soft Chicago Blue Clay. Chicago has been called the birthplace of the Skyscraper and drilled shaft foundation, both of which came about in the 19th century. After the Great Fire of 1871, tall new structures were built rapidly and designing a successful foundation was trial and error. The first deep driven wood pile and caisson foundations bypassed the problem layer and found solid support on hardpan till or bedrock below (Schock and Risberg 2013). Once the drilled shaft foundation became acceptable to the Chicago engineering and construction community, building heights and complexity grew dramatically. As the city grew, building foundations were being repurposed. There was also the need to underpin structures for additional loads and shallow foundations for adjacent construction. Hand-dug drilled shafts were an option for some of these restricted access and low headroom sites but a new technique, micropiles, would prove to be the future of retrofit and hard to construct foundations. Micropiles were introduced on a limited basis to the United States market in the 1970s and 80s. In the early 1990s, the Chicago market began to latch onto micropiles and their use has grown significantly as a solution to the most complex foundation problems a maturing skyline has to offer.

Jan 1, 2019

By David J. Puller

As part of the value engineering process on a major Design Build highway project, instrumented trial pile load tests were used to achieve savings in cost and time on the foundations for a major river crossing. Two trial piles were tested close to failure load at 25MN. Following the interpretation of the pile load test results which included the determination of the ultimate shaft and base capacity, the mobilisation of the shaft and base resistance with pile displacement, and correlations with vertical effective stress and SPT profile, a revised design methodology was proposed. A 25% enhancement on commonly assumed ultimate shaft friction in Chalk was adopted. In addition a significant reduction in the Factor of Safety on end-bearing capacity generally used was also implemented. The revised design resulted in a significant cost and time saving on the piling operation with the pile length reduced by up to 6m (approx. 20%) for the river piers.

Jan 1, 2002

By Serhat Baycan, Mikias Yohannes

"Kuala Lumpur Karst is a complex limestone formation that is characterized by presence of cavities, solution channels, pinnacles and floaters. Basement excavations in such geological formations are usually challenging, mainly owing to the unpredictable rock head depths and potential for groundwater inflow. Any excavation support system should have adequate robustness and water tightness. Traditionally, Secant Bored Pile walls (SBP) with struts are the preferred option for karst ground. This paper discusses a cost effective and innovative alternative solution for a particular site – using Deep Soil Mixing (DSM) and using Contiguous Bored Piles (CBP) together with Ground Anchors (GA). The site, located around one of the busiest areas of Kuala Lumpur, is a 5,700 m2 commercial and residential development. A 16.0 m deep excavation was needed for four levels of basement and excavation support along the 275 m perimeter of the development. Within the site, the depth to rock head varied from 6 m to 19 m. The basis for each solution and conditions for its suitability are discussed in detail. Some design considerations and construction challenges are also presented. The performance of the two retention systems during excavation are presented, together with comparisons versus design predictions. Suggestions for future development are also given. Advantages of this approach compared to other traditional approaches are highlighted.1. INTRODUCTIONThe geology of Kuala Lumpur is among the most complicated and geotechnically challenging formations in South East Asia. The majority of the city falls into the Kuala Lumpur Limestone formation; which is a thick, highly-weathered and cavernous limestone. This formation is pure calcitic to dolomitic in composition, having infrequent schist and phyllite interbedding (Gobbett et al., 1973).The KL limestone has a highly karstic topography dotted with cavities, ravines, interconnected subterranean channels, pinnacles, overhangs, floaters and slump zones (Tan, 2006). This results in erratic bedrock profiles even within short distances. It is not uncommon to see a precipitous rock head incidence within short distances in the same site. In most parts of the City, the bedrock is typically encountered ranging from very shallow depths to about 30.0 m. The exception to this is at the heart of the City, where Kenny Hill formation prevails above the KL limestone. In such cases the limestone bedrock can be encountered much deeper. The erratic rock head profile and the highly karstic nature of the KL limestone makes it a geotechnical challenge requiring careful consideration of suitable engineering solutions.1.1 – Site DescriptionThe site, located in downtown Kuala Lumpur, is abutted by a busy street on the North. Before development, the site previously served as a car park. To the west an access road separates the site from an empty lot; while on the east, the lot is bounded by light weight residential and commercial buildings. On the south side, the site is bordered by a road that separates it from a prominent Shopping Mall in the City. A layout plan and an artist’s impression of the finished development is shown in Figure 1."

Jan 1, 1900

By Sameh M. Khella

This paper discusses the application of deep CFA piles for the foundation of structures in different ground stratifications with a focus on the application in Queensland region. Design, construction techniques and quality measures implemented during these procedures are described. Testing methods and verification of capacity, integrity and performance of these piles are also demonstrated. Case studies for this application are presented with an appreciation of this solution within the provided project conditions of each case. Examples of successes and challenges encountered over the course of application of deep CFA in Queensland are mentioned. Limitations of the technique and less favourable situations for its implementation are also highlighted.

Nov 1, 2022

By John P. Turner, Steven S. Dapp, Dan A. Brown

"The Goethals Bridge Replacement (GBR) spanning the Arthur Kill Waterway between Elizabeth, NJ and Staten Island, NY consists of a dual-span 1,982.5-ft long cable-stayed bridge with approach spans of 2,545 ft on the NJ side and 2,788 ft on the NY side. The bridge is supported on over 200 drilled shaft foundations ranging in diameter from 4.5 ft to 10 ft and socketed into Passaic Formation siltstone. Drilled shaft resistances for design were based on load tests as described in a companion paper (Dapp et al. 2016). This paper presents the main foundation design considerations and challenges. The approach to construction of the rock sockets, with a focus on quality in order to support the use of high nominal values of side and base resistance, is described. Lessons learned from this project and their application to future similar projects are presented.INTRODUCTION AND BACKGROUNDThe Goethals Bridge Replacement (GBR) project is a Public-Private Partnership (P3) that represents a major milestone for the Port Authority of New York and New Jersey (PANYNJ) in its distinguished history of bridge building in the greater New York City metropolitan area. The new bridge will replace the existing Goethals Bridge, named after Major General George W. Goethals, Chief Engineer of the Panama Canal and the first consulting engineer for the Port Authority. The existing Goethals Bridge along with the Outerbridge Crossing and the Bayonne Bridge comprise the three Port Authority bridges connecting Staten Island with New Jersey. The existing Goethals Bridge and the Outerbridge Crossing are cantilever truss structures and both opened on the same day in 1928. They were designed by J.A.L. Waddell under the supervision of the eminent engineer Othmar H. Ammann (1879-1965), who was the designer of many other iconic bridges in the NY City area including the Bayonne Bridge (1931), the George Washington Bridge (1931), and the Verrazano Narrows Bridge (1964). The designer of record for the replacement Goethals Bridge is Parsons Corporation, which is the successor firm of Robinson & Steinman, whose principal David B. Steinman was also a notable NY area bridge designer and a contemporary and rival of O.H. Ammann.The replacement Goethals Bridge is supported on over 200 rock-socketed drilled shaft foundations. Each main pylon tower is supported on a group of six 9-ft diameter drilled shafts and each anchor pier is supported by two 10-ft diameter shafts. Each approach pier consists of a two-column bent with each column supported on a rock-socketed drilled shaft. A rendering of the Main Bridge crossing the Arthur Kill is shown in Fig. 1."

Jan 1, 2016

By Joe Harris

Large structures, such as a multistory office building or a large storage tank, are constructed the most economical way possible, which may involve a shallow foundation system placed on native soil or compacted fill material. Over the life of the structure, the foundation system may not perform as originally anticipated, leading to differential settlement. Minor differ- ential settlement is expected; however, settlement that exceeds allotted tolerance can render the structure inoperable. Compaction grouting is a well-known and accepted ground improvement technique that can be used to not only stabilize but relevel multistory buildings and large dia- meter storage tanks. Two projects, each with differing types of structures, were successfully remediated utilizing com- paction grouting as the primary method to remedy settlement.

Sep 1, 2023

By Steve Davidow, Scott Tunison

As the demand for electric power grows and generation facilities are constructed in more remote areas, the industry faces an increasing number of foundation construction challenges. The importance of quality geotechnical information prior to construction is accentuated by the linear nature of the projects and the potential for drastic changes from one end to the other, but is often difficult or unfeasible to obtain. Alignments are crossing remote, rugged and/or environmentally protected terrain, and completing a comprehensive geotechnical program is made challenging from an access or economic standpoint, or both. In these situations, the industry needs a flexible foundation alternative. This paper will present micropiles as that alternative and demonstrate how the implementation of micropile foundations mitigated these challenges on the Koolau-Wailupe 46 kV Circuits in Oahu, Hawaii, which involved rugged, steep slopes and helicopter construction methods. It will detail the selection of micropiles over other foundation options, micropile and steel pile cap design methodologies, foundation construction, and quality control. Special attention will be given to the unique geology in the area, and why precise identification of saprolite and basalt layers was integral to the successful performance of the foundations. The intention is to communicate the benefits of a flexible solution based on continuous collaboration between design and construction.

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"Previous studies revealed that the helix deflection reduced the end bearing capacity of screw pile in dense ground even if the installation process is completed with minimal soil disturbance. The ultimate end bearing capacity in dense ground is difficult to achieve during the full-scale pile load test due to the limitation of the loading system. Therefore, in the present study, model scale of testing is selected to investigate the effect of helix deflection on load settlement behavior of single helix screw pile under increasing stress level. It is observed from the test results that the applied surcharge pressure, which is used to simulate the effect of stress level, is decreased with increase in model ground thickness. This decrease in the stress level is due to the frictional resistance between the container wall and sand. It is also observed that the end bearing capacity of screw pile increases with the increase in stress level but at gradually decreasing rate. The test results indicated that the helix deflection during the pile load test should not be more than critical deflection (0.72 mm average) of the helix to avoid any reduction in the end bearing capacity of screw pile. The helix deflection, which is measured after the pile load tests are also compared with the equations of flat circular plate having uniformly distributed load over the plate with simply supported and fixed inner edges.INTRODUCTIONThe screw pile consists of a central steel shaft with one or more helices attached at different location on the central shaft. The installation mechanism of screw pile consists of torque and pushing force. The screw pile installation mechanism can affect the unit weight of the ground during its installation. This effect is small in cohesive soils but it is quite noticeable in loose to medium dense sands (Adams 2011; Santos et al. 2013). The pushing force should be controlled in such a manner that pile penetration should be at least 80% of the pitch of the helix, during each revolution (Perko, 2009)."

Jan 1, 2017

By Arash Khosravifar

One of our research thrusts at Portland State University (PSU) centers on developing design guidelines for pile foundations in liquefiable, laterally spreading grounds. This research has been primarily sponsored by the DFI Committee Project Fund (CPF) program through four awards, totaling nearly $240,000 in financial support. DFI contributed half of this financial support, while the other half was contributed in-kind by PSU and DFI Project Advisory Board members. Leveraging the CPF funds, we secured an additional $550,000 in financial support from the National Science. Foundation (NSF), which has enabled our research group to continue exploring this topic and contributing to the broader engineering community's understanding of the behavior of pile foundations in liquefiable soils. The CPF funds have fostered collaborations with practitioners and researchers beyond PSU. Notable examples include collaborative research involving data from five large-scale centrifuge tests on pile-supported wharves by Steve Dickenson, Ph.D., New Albion Geotechnical; Nason McCullough, Ph.D., Jacobs Engineering and Scott Schlechter, Geotechnical Resources, as well as 1-g shake table tests of bridge pile shafts conducted by Professors Ahmed Elgamal, Ph.D., and Ahmed Ebeido, Ph.D., of the University of California, San Diego. In addition to these collaborations, our research has benefited from industry-university partnerships formed through the involvement of DFI Project Advisory Board members. Their support and feedback ensure that our research products are practical and imple- mentable in real-world projects. The impact of the CPF funds extends to supporting graduate students' theses, which were the basis for 17 technical publications. Some of these publications are expected to have a significant impact on the industry. For instance, our 2018 DFI Journal paper, co-authored by former master's student Jonathan Nasr, cur- rently with the Army Corps of Engineers, has been cited in the 2022 British Columbia Supplement to Canadian Highway Bridge Design Code S6:19. A noteworthy product of our study is a step-by-step design procedure for pile- supported wharf structures subjected to the combined effects of lateral spreading and inertial loads, outlined in a 2022 American Society of Civil Engineers' (ASCE) Journal of Geotechnical and Geo- environmental Engineering paper co- authored by former doctoral student Milad Souri, Ph.D., PE, Geotechnical Resources.

Nov 1, 2023

By Terry Eldridge, Keith MacKay, David Siddle, Luke Moger

On August 4th, 2014, a breach occurred in the Perimeter Embankment of the Tailings Storage Facility (TSF) located at the Mount Polley Mine, releasing approximately 10.6 million m3 of supernatant water, 7.3 million m3 of tailings solids, 6.5 million m3 of tailings interstitial water and 0.6 million m3of construction materials. A Temporary Upstream Rockfill Berm was constructed between August 2014 and February 2015 within the area of the tailings dam failure in order to retain the remaining tailings solids during the low flows of the winter season. The Temporary Upstream Rockfill Berm was constructed as part of the initial response phase, with the primary objective to abate the flow of tailings into the receiving environment. A secondary objective of its construction was facilitating the required investigation works downstream of the tailings dam failure. The selection of the coarse grained material used in the construction of the Temporary Upstream Rockfill Berm was based on the availability of the material (timeliness of construction) and the non-water retaining design of this initial response phase. Consequently, an alternative method was required in order to prevent further loss of mine-affected water and tailings from the TSF, as well as to provide short-term contingency water storage, during high flow conditions expected in late spring. Golder Associates Ltd. designed the 2015 Freshet Management Embankment, a deep mixing cut-off wall, to meet these site requirements, which was constructed by Mount Polley Mining Corporation and Golder Construction Inc. between December 2015 and April 2015. The works included 132 soil cement panels constructed to depths of up to 27 meters. This aspect of the works was completed using an RG25S Bauer CSM rig on a 24 hour per day, 7 day per week schedule. The cut-off wall specifications included a target unconfined compressional strength (UCS) of between 1 and 2 MPa, a maximum hydraulic conductivity of 1x10-6 cm/s, and a ductility to enable the soil cement to undergo a minimum of 5% strain without a reduction in strength or increase in hydraulic conductivity. In order to control and assure the quality of the soil cement, 2553 wet grab specimens were retrieved from the fresh soil cement panels using a project-developed sampler. Four of the soil cement panels were cored with a mud-rotary drill rig and optical and acoustic televiewers were placed into the boreholes in order to log several relevant parameters, including image, texture, relative hardness, borehole-shape, and temperature.

Jan 1, 2016

By V. A. Sernov

"One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result building terms and foundation costs reduce considerably. However, nowadays in Belarus there is no reliable and suitable in design practice methods of calculation of piled-raft foundations. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of field and laboratory investigations in Minsk. The most important results of the investigations are provided in the article. Methods of analysis of piled-raft foundations are described.INTRODUCTIONPile foundations of late years are used extensively in connection with the increased number of storeys and load increment on the soil. Often pile foundations are applied in comparative favorable ground conditions at the surface of the base. In such cases the increase of the bearing capacity of foundations and the reduction of construction cost are questions of primary importance for designers. One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result, building terms and foundation costs are reduced considerably. However, nowadays there is no reliable and suitable in design practice methods of calculation pile foundations with bearing rafts. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of laboratory and field investigations.Long before the constitution of the first piled-raft foundations in the Soviet Union there were attempts to consider soil resistance in the basis of isolated and strip grillages. Such bases can be considered as separate fragments of the piled-raft foundation. Prof. A. A. Bartolomey had tested more than 70 pile foundations of natural size in different ground conditions. The length of piles was 3 12 m (?????????? 1995). The observed results show that the raft carries about 10 12% of the total load applied when length of piles is over 9 m and space between piles is a=3d. Bearing capacity of the raft is about 35 40% when the length of piles is 5 8 m and a=6d. Prof. Golubkov has tested 2 prismatic piles (cross section: 350x350 mm, L=3800 m) and 2 pyramidal piles (cross section: head - 600x600 mm, foot – 100x100 mm, L=3000 m). One of the piles was tested with a raft and the other one without a raft. Significant influence of the raft on total bearing capacity was determined, the more the settlement was the more it influenced on the raft. Bearing capacity of the raft was 27,5% in foundation with prismatic pile and 42% with pyramidal pile (???????? et al. 1971)."

Jan 1, 2016

By John S. Pack

The application of square shaft helical piers in expansive soils is a standard of practice in many areas of the United States. Over 20 years of performance monitoring show exceptional performance and economy will result if proper design procedures, specification requirements and installation procedures are followed. This is true for new foundations and the repair of existing foundations, including lightly loaded wood-frame structures on expansive soils. Proper design includes: 1) site geotechnical characterization, 2) pier layout such that each pier is loaded to its maximum design capacity, 3) maximize spans between piers, 4) minimize the number of piers, 5) isolate the structure from the expansive soil with an appropriate void zone below all grade beams, slabs or other components that would otherwise be in soil contact and 6) utilize only single helix piers. Proper specification employs a performance specification that specifies: 1) the design load on each pier with a suitable safety factor, 2) the minimum installation torque, typically 4,000 ft-lbs (5.4 kN-m), or refusal, 3) a minimum pier shaft steel Fy = 70 to 90 ksi (483 to 621 Mpa) and pier helix steel Fy = 80 ksi (552 Mpa), 4) 1.5 to 1.75 inch (38.1 to 44.5 mm) square shafts, 5) smooth shaft surface, 6) the ICC Evaluation Report (ER) number of the manufacturer and 7) the manufacturer ISO 9001 certification for material quality control. Proper installation requires: 1) equipment with sufficient axial compression force (crowd) on the pier shaft so the helix engages the soil and advances to the specified minimum installation torque or refusal, 2) additional specialized techniques for expansive soils and 3) qualified specialty helical pier installation contractors experienced in expansive soils who submit and utilize pier configurations, techniques and equipment that will most effectively and economically meet the specified performance.

Jan 1, 2007

By Michael W. Neill, O&apos

This presentation addresses some of the problems encountered in estimating the capacity of drilled shafts and augered, cast-in-place piles in soft rock. Methods to quantify side and base resistance are suggested. However, the methods that are described should always be verified locally by performing load tests.

Jan 1, 2001

By Chunli Wei, Mark Jen, Xiaojun Wang

"After more than 85 years of service, a critical link between New York and New Jersey, the Goethals Bridge over the Arthur Kill waterway, is being replaced with two new parallel bridges. Each bridge includes 1,650 feet long signature steel composite cable-stayed bridge, a 2,789 feet long New York approach and a 1,889 feet long New Jersey approach. The superstructure of each approach is supported on a series of two-column concrete piers and each column is supported on a single large diameter drilled shaft varying from 4.5 to 9 feet in diameter and anchored 45 feet below ground into the underlying rock.A performance-based methodology was followed for the strength and extreme event limit states design of the drilled shaft foundations. The design for seismic loads has been performed using the AASHTO Guide Specifications for LRFD Seismic Bridge Design. For all strength and service loads, the AASHTO LRFD Bridge Design Specifications were used. Since the longitudinal and confinement requirements in the two specifications vary, the minimum longitudinal reinforcement was based on the more stringent requirements of the two codes. A design example is presented to illustrate the methodology in bridge deep foundation design using nonlinear time-history global analysis results with soil-pile interaction represented by sets of horizontal and vertical nonlinear soil springs along the drilled shaft, based on the soil and rock properties from the boreholes test results. In this paper the design methodology implements strain limits related to earthquake intensities and damage levels to calculate the capacity using XTRACT analysis, which aids designers to adopt applicable provisions that meet specific design requirements.INTRODUCTIONAfter more than 85 years of service, a critical link between New York and New Jersey, the Goethals Bridge over the Arthur Kill waterway, is being replaced with two new parallel bridges designed to carry vehicular traffic and a future mass transit corridor. They include two 1,650 feet long signature steel composite cablestayed bridges with 260 feet tall V-shaped concrete gateway towers (Figure 1). The approaches consist of continuous pre-stressed concrete girders. The New York approach is a single structure consisting of 18 continuous spans, sloping at 4% for a total length of 2,789 feet without expansion joints. Similarly, the longest continuous portion on the New Jersey approach, with a similar slope, consists of 11 spans for a total length of 1,889 feet without expansion joints. The superstructure of each approach is supported on a series of two-column concrete piers that vary in height from 121.3 feet near the cable-stayed bridges to 11.8 feet near the abutments. Each column is supported on a single large diameter drilled shaft varying from 4.5 to 9 feet in diameter and anchored 45 feet below ground into the underlying rock."

Jan 1, 2016

By John C. Ryan

The Emeca Pile Splice, an innovative mechanical prestressed concrete pile splice, is the first robotically welded splice to be fabricated in the United States. An analytical and experimental study was conducted to establish the capacity of the standard splice for 12-in. and 14-in. square piles. The study illustrates compliance of the splice with International Building Code (2006) requirements. A case study for a large petroleum tank foundation project in Port Canaveral, FL is presented, demonstrating the efficiency achieved through use of spliced-piles. For the case-study project, single-piece 18-in.-square, 100-ft-long piles were replaced with 12-in.-square, two-piece, spliced piles. As a result, a significant reduction of material, labor, handling, and equipment was documented for the project. Savings realized on the installed pile cost was estimated to be in excess of 30% by the owner.

Jan 1, 2010

By J. Hamada, K. Yamashita, Y. Shigeno, T. Tanikawa

"This paper offers a case history of piled raft foundation in soft ground supporting a twelve-story building in Tokyo. To increase bearing capacity of the soft soil as well as a countermeasure of liquefaction, grid-form deep cement mixing walls (DMWs) were employed with the piled raft. Based on the long-term monitoring results, the ratio of the load carried by the DMWs to the effective structure load after the construction of the raft was estimated to be 0.3 while that carried by the piles was 0.7. In order to clarify the contribution of the DMWs to bearing the structure load, numerical simulation of the settlement and the load sharing among the piles, the DMWs and the unstabilized soil was performed using a three-dimensional finite element model. The results of the numerical simulation agreed well with the measured values, when the Young’s modulus of the DMWs obtained from the unconfined compressive tests was adopted and the shear modulus of the soft soil was reduced to 50% of that at small strains.INTRODUCTIONIn recent years, piled raft foundations have been used in many countries as building foundations. The effectiveness of piled rafts in reducing average and differential settlements has been confirmed not only on favorable ground conditions as shown by Katzenbach et al. (2000), Poulos (2001) and Mandolini et al. (2005), but also on unfavorable ground conditions such as soft clay and/or liquefiable sand using ground improvement technique (Yamashita et al., 2011a; Yamashita et al., 2011b; Yamashita et al. 2013). Grid type ground improvement using the Deep Mixing Method has been applied to sandy ground as a countermeasure of liquefaction to increase liquefaction resistance of unstabilized soil left in the grid walls where its shear deformation during seismic motion is reduced by the confinement effect of the grid walls (Kitazume, 2013). The high applicability of the method was demonstrated in the 1995 Hyogoken-Nambu earthquake and the 2011 off the Pacific coast of Tohoku Earthquake (Tokimatsu et al., 1996; Uchida et al., 2012a; Uchida et al., 2012b).This paper offers a case history of piled raft foundation in soft ground supporting a twelve-story building in Tokyo. To increase bearing capacity of the soft soil as well as a countermeasure of liquefaction, grid-form deep cement mixing walls (DMWs) were employed with the piled raft. First, the results of long-term field monitoring on the settlement and the load sharing among the piles, the DMWs and the unstabilized soil are briefly described. Next, to clarify the contribution of the DMWs to bearing the structure load, the foundation behavior is simulated using a three-dimensional finite element model, and then the results of the numerical simulation are discussed."

Jan 1, 2015

By Gerald Verbeek, Erick Baziw

Dynamic soil analysis (DSA) in geotechnical practice is intimately related to the capability of measuring the necessary soil properties of shear modulus and absorption. In DSA the methods of analysis are based upon the stress-deformation response of soils due to imposed shear strains. Typically the soil profile is numerically modeled as linear visco-elastic system. This technique is referred to as the Equivalent Linear (EL) method, and it requires the specification of the input parameters of low-strain (<10-5) shear modulus, modulus reduction, and the equivalent viscous damping ratio, which is directly related to the soil absorption value. Downhole seismic testing (DST) has proven to be a very accurate tool for estimating low strain shear modulus values as long as source wave raypaths are taken into account, especially for near-surface investigations. DST has also been utilized to estimate low-strain interval absorption values. In these cases standard frequency domain absorption estimation algorithms (such as the spectral ratio technique) are utilized where it is assumed that the source waves are traveling along the same travel path, which is obviously not the case for near surface DST investigations. This paper outlines a unique DST absorption estimation methodology, which is carried out in the time domain and takes into account source wave travel paths. 1. INTRODUCTION There is considerable interest in methods of geotechnical in-situ engineering that provide accurate estimates of the shear wave velocity and the associated absorption values in the ground, since these parameters form the core of mathematical theorems to describe the elasticity/plasticity of soils and they are used to predict the soil response (settlement, liquefaction or failure) to imposed loads (whether from foundations, heavy equipment, earthquakes or explosions).

Jan 1, 2019