Search Documents

By Walid El Kamash, Sadik Oztoprak

"Soft soil presents a challenge against multistory buildings in some cities of Egypt such as Port Said due to the consolidation settlement. Deep mixed (DM) columns are used to improve the soft foundation soil in order to reduce the total and differential settlements. Latest research revealed that this improvement technique also increases the rate of mechanical consolidation due to column yielding caused by stress concentration from the soft soil. In this study, extended poly-styrene (EPS) Geofoam is used to replace the soft soil over DM columns in order to control the stress concentration and settlement. To understand the effect of EPS geofoam on the degree of consolidation, stress concentration and settlement, a parametric study was carried out through a mechanically and hydraulically-coupled numerical method. A unit cell model is used, in which the soil was considered linear elastic; DM column and EPS Geofoam are elasticplastic materials. Results reveal that EPS geofoam is helpful for reducing the settlements and accelerating the consolidation. Increasing the length of the column of the deep mixed foundation with EPS geofoam has a significant effect on accelerating the consolidation.INTRODUCTIONExpanded polystyrene (EPS) geofoam is a lightweight polymeric material which is made by expansion of raw plastic beads. The expansion of the EPS beads are spherical-shaped particles containing closed hollow cells. EPS which plays an important role as an innovative lightweight construction material is now well recognized due to its low density in addition to high compressive and rupture strength. Inglis (1996) reported the first use of EPS geofoam as a seismic buffer to reduce potential seismic loads against a nonyielding basement wall. Gaskin (2000) and Bathurst et al. (2007) carried out reduced-scale shaking table test on a rigid retaining wall protected by EPS geofoam. The test data showed that the peak lateral loads acting on compressible model walls were reduced below values measured for nominally identical structure but with no compressible inclusion. Abdelrahman and El Kamash (2014) investigated the behavior of EPS Geofoam beneath raft foundation on soft soil of Port Said. They showed the ability of EPS to control vertical displacements. The investigation of the behavior of EPS geofoam with DM column has not attracted more attention of previous researchers. In this paper, the behavior of replacing the soft soil by EPS geofoam was examined in the presence of DM column."

Jan 1, 2015

By Charles G. Crans, Naresh Gurpersaud

"Toronto’s Union Station, a National Historic Site occupying an entire city block, is the busiest commuter rail transportation hub in Canada. An extensive project is being undertaken to revitalize Union Station while maintaining the historical significance of the building and minimizing disruption to commuters. A significant stage of the revitalization involves excavation indoors, to a depth of up to 5.5 m below the existing floor level to create space for a new transit concourse and a new lower-level pedestrian retail concourse. A hybrid excavation support system utilizing micropiles as soldier piles was constructed over an 18 month period between 2010 and 2011.Development and testing of connections between the micropiles, shotcrete facing, lagging, walers, and tiebacks presented significant challenges. The existing viaduct structure was constructed in the 1920’s on land reclaimed from Toronto Harbour, so there was significant (and ongoing) uncertainty with respect to buried obstructions including relic timber wharfs and abandoned steel and timber piles. Collectively all these conditions precluded the use of conventional methodology; new techniques, installed using modified equipment, and for the first time in the Greater Toronto Area, were required.Details of the existing site conditions, installation challenges, design, construction and performance of the hybrid excavation support system inside this historic structure are presented.INTRODUCTIONUnion Station in Toronto, Ontario is the busiest passenger rail facility in Canada, with 65 million passengers annually and an average of 200,000 passengers each day. Construction of the station was completed in 1920. It has been designated a National Historic Site of Canada and inducted into the North America Railway Hall of Fame in the Facility and Structure category.The Union Station Revitalization Project (USRP) was tendered in 2010 and awarded as a 6-year, $450M construction management / trade contract package. Included was a large scale grade reduction, referred to as “The Dig Down”, to create two basement levels and this required extensive excavation support constructed entirely indoors within the active station setting."

Jan 1, 2017

By Fred Fuchs

"Most deep foundation work is either unseen by the general public or viewed as an inconvenience in their daily lives. Hurricane Katrina changed that perspective for everyone in New Orleans — and many other people in the U.S. and abroad. The public and the government of south Louisiana, and the U.S. Army Corps of Engineers (USACE), all needed to restore trust in the system that protects their property and, more importantly, their lives. While much has been written about the failures of government agencies, in this case incredible solutions were devised and implemented despite daunting schedules and arduous conditions. These solutions were achieved through collaboration, and through the efforts of USACE, where the goal was to fi nd the most expeditious and effective design/build solutions. This disaster thrust the pile driving industry into the national spotlight. Boh Bros. Construction Co., L.L.C., along with numerous local and national heavy construction companies, subcontractors, material suppliers and government agencies, take pride in the milestones reached after Hurricane Katrina.The majority of New Orleans’ population lives below sea level. Historically, the city has been protected by a fl ood control system consisting of earthen levees and I-walls (steel sheet pile topped by vertical concrete wall). Rainwater is pumped out of the city over this protection system and into canals that feed into Lake Pontchartrain. On August 29, 2005, when Hurricane Katrina made landfall just east of the city, the levee system experienced a major failure of several I-walls lining the outfall canals, causing flooding of 74% of the east bank of the city. The counterclockwise rotation of the wind pushed the lake water onto the south shore, raising the level of water more than 10 ft (3 m). A failure of 450 ft (137 m) of floodwall lining the east side of the 17th Street Canal caused extensive damage. This breach prevented the use of the pump stations that outfall into the 3-mile (4.8 km) long 17th Street Canal."

Jan 1, 2008

By James W. Niehoff

"Prior to 2003, most high rise structures in Honolulu, Hawaii were supported on driven pile foundations, extending through shallow coral strata and bearing in competent formations at depths of 100 ft (30 m) or greater. In 2003, the 40-story Hokua Tower became the first building in Hawaii to use continuous flight auger (CFA) piles for support. These piles derived most of their capacity from side shear in the shallow coral formations, which reduced their required lengths to less than 100 ft (30 m) sand significantly increased their capacity. Not only did CFA piles prove to be more efficient and cost-effective than driven piles, but the reduced noise and vibration associated with their installation made them and drilled piers the foundations of choice for most mid- to high-rise projects going forward. Because drilled foundations were new to Hawaii, it was necessary to develop effective design parameters for the unique soil and rock conditions found within this urban area. While drilled foundations were found to have many advantages over driven piles, construction techniques had to be modified to compensate for extensive voids in the coral formations. This paper presents a compendium of the data derived from numerous full scale, instrumented load tests conducted during the past decade and provides guidance for the design and installation of CFA and drilled pier foundation systems in areas having geologic settings and history similar to that of Honolulu.INTRODUCTIONThe State of Hawaii is one of the most remote areas in the world, lying nearly 2400 miles (3800 km) from the nearest continental land mass. In spite of this vast distance, the population of the islands has grown to over 1 million people, the majority of whom live within and in close proximity to the City of Honolulu on the Island of Oahu. The city is densely populated with over 400 high rise apartments, condominiums, hotels and office buildings located within 5 miles (8 km) of the city center (Fig.1). Nearly all of these buildings have been constructed within the past 50 years."

Jan 1, 2016

By Jonathan G. Cannon

"This paper will describe dynamic pile testing conducted during installation of driven octagonal precast prestressed concrete piles used as the foundation for this bridge. The piles were long and hence spliced. A number of the piles showed damage near the splices and the damage location was near the ground surface so that the damage could be verified using visual inspection. The piles and splice configuration are still in use today without modification. Further WEAP driveability analysis has been conducted which demonstrates the effect of the splice on pile stresses and a likely failure mode. A slight modification is proposed to the splice that should prevent the damage on future projects.INTRODUCTIONThe bridge site is located on the Olympic Way, Route 41, about 20km north of the regional centre of Albury, NSW. For a long distance north of the site the Olympic Way ""shadows"" the main Melbourne to Sydney rail line and is located on the Western side and in close proximity. At the bridge site there was previously a sharp dog-leg in the road and a right angle level crossing with the road changing to the Eastern side of the rail line, eventually joining up with the Hume Highway, which in turn now becomes a ring-road through the eastern outskirts of Albury. The dog-leg and rail crossing had warning signs and bells, speed restrictions and rumble strips to warn approaching motorists to reduce speed. Site distance was exceptionally good.Approximately 2years before construction a group of five ""high spirited"" young men from the local area were driving south on the Olympic Way adjacent to a south-bound train. It is understood they interacted with the train crew for a period of time. Unfortunately the car and train collided at the level crossing and all of the young men were killed. There were outpourings of grief in the local community and a decision was made to replace the level crossing with a road-over-rail bridge.The bridge was highly skewed with two piers and two high level abutments with fill embankments on both approaches.GROUND CONDITIONSThe site is open grazing country with approximately level ground at the site with surrounding low hills. The geology was unremarkable with consistent stiff clays for a considerable depth.The design required driven precast prestressed pile foundations with the piles to be driven to a considerable depth.Hard driving with high tension stresses were evident from the start of driving and a variety of different pre-bore lengths were adopted in an attempt to minimise driving and potential for damage. At the abutments the pile locations were predrilled for at least the full embankment depth.PILESThe piles were 550mm octagonal prestressed concrete with the pier piles being single piece and the longer abutment piles being two-piece with a ""standard"" epoxy glued box splice. Pier piles and the initial length of the abutment piles were 24m. The add-on piece used at the abutments was 12m. Pile concrete was grade 50MPa."

Jan 1, 1900

By Rae Mackay, Kaveh Ranjbar Pouya, Ali Tolooiyan

"A major part of Melbourne’s central business district is underlain by a very soft silty clay deposit known as Coode Island Silt (CIS). Due to the low strength of CIS, most construction in the region is based on pile foundation systems. Traditionally, the design of pile foundations is mostly based on empirical and analytical methods. However, numerical methods such as Finite Element Methods (FEM) can be utilised for more accurate estimation of the bearing capacity and deformation of pile foundation systems, especially in complex loading scenarios. Unfortunately, no systematic effort is made yet to calibrate a realistic nonlinear constitutive model to describe the geomechanical behaviour of CIS in a numerically based solution. Among the nonlinear constitutive models, the Hardening Soil (HS) model is an advanced hyperbolic model which accounts for the nonlinearity of stress-strain relationship as well as the stress dependency of the soil stiffness. In this study, the HS model is calibrated based on laboratory tests performed on CIS. Also, to validate the accuracy of the calibration, the wellknown cavity expansion theory is employed to model the CPT cone tip resistance (qc) in CIS, and results are compared against the measured CPT qc profile at the field.INTRODUCTIONA large percentage of world’s coastal areas are covered with soft marine clay deposits. Having very low shear strength and high compressibility, the alluvial deposits are known as one of the most problematic soil layers for the design and construction of infrastructure facilities. A major part of Melbourne’s central business district is underlain by a very soft silty clay deposit known as Coode Island Silt (CIS). Basically, there are two main solutions for construction in such weak soil conditions. One is the use of pile foundations transferring the applied load to deeper and stronger soil layers, and the second one is to employ ground improvement techniques such as using deep soil mixing columns to improve the bearing capacity of the soil. In both cases, a practical geotechnical design should incorporate both stability analysis and deformation analysis to achieve a cost-effective and reliable solution. Most of the classic solutions for stability analyses such as limit equilibrium analysis disregard the stress-strain relationship of the soil for the sake of the simplicity (Chen, 2007; Sokoloviskii, 1965). In a similar simple approach, most of the past studies of deformation analysis have been established on the basis of linear elasticity. However, it is well recognised that the soil stress-strain behaviour is highly nonlinear even at very small strains (Burland, 1989). Hence, for a precise deformation analysis of the foundation of important geotechnical structures, the application of advanced nonlinear constitutive models is extremely beneficial. Precise deformation analysis is essential as geotechnical designers have to predict the displacement of geotechnical structure and the adjacent soil as well as the induced displacement and forces to adjacent structures. This issue is more highlighted recently in the analysis, and design of highly important infrastructures as geotechnical engineers are facing new challenges in the analysis and design of infrastructures in congested areas. Rapid population growth, especially in the major cities all around the world necessitates the design and construction of more integrated infrastructure facilities. Consequently, geotechnical engineers should employ more advanced design approaches to address the new challenges in geotechnical engineering practice. Complicated geometries, different loading scenarios and the application of nonlinear deformation models which is believed to be essential for a precise deformation analysis, necessitate the application of numerical methods to satisfy most of the design requirements."

Jan 1, 1900

By Jim Bruce, Naresh Gurpersaud

"The West Toronto Diamond project, under construction since 2006 and due to be complete in 2015, is a rail-to-rail grade separation project in the heart of urban Toronto. Once complete, a depressed corridor over 1000 metres long will take the CN tracks beneath the CPR tracks. An interlocking steel pile wall serves to retain ground and cut off groundwater. Remedial measures, constructed using jet grouting, were required at several locations within and behind the steel piles.At mechanical interlock joints damaged or suspected of being damaged, jet grouting was used to improve native soils on the retained side of the wall to reduce permeability of the soil mass in intimate contact with the joints to 10-7 cm/s. At a number of steel piles where groundwater and soil type combined to cause basal instability inside the pipes during the interim between excavation and concreting, jet grouting was used to construct temporary bottom seals. At locations near adjacent structures where the steel pile installation process resulted in disturbed ground on the retained side of the wall, jet grouting was used to strengthen and stabilize ground.This paper outlines the details of the various jet grouting applications, the respective testing programs implemented to demonstrate in situ permeability and strength of the soil-grout matrix, and performance of the constructed system.INTRODUCTIONThe West Toronto Diamond (WTD) is a junction of several railway lines, all intersecting at the same grade (Figure 1). A major grade separation project at this site commenced in 2006 and is scheduled to be completed in 2015. The whole of the work is comprised of multiple contracts, completed and/or ongoing, by different constructors. Once completed, a depressed corridor over 1000 metres long with over 23,500 m2 (face area) of retained earth will bring the CN tracks beneath the CPR tracks and eliminate a major bottleneck at the most heavily used rail crossing in Canada."

Jan 1, 2017

By Greg Canivan, Bernie Hertlein, Les Chernauskas, Joram Amir, Garland Likins, E. Anna Sellountou, Tim Kovacs, Peter Kandaris

Nondestructive testing of drilled shaft foundations via Crosshole Sonic Logging (CSL) is often performed as part of the quality assurance process to assess the soundness of concrete. The intent of CSL testing is to identify irregularities such as soil intrusion, necking, soft bottom, segregation, voids and other defects that could result in poor structural performance of the foundation. Over time, CSL rating criteria based on first arrival time and relative energy have incorrectly evolved to often be the sole means of determining the acceptability of a shaft. Some of these criteria have found their way into regulatory agency specifications, with acceptance values often differing from agency to agency.The purpose of this document is to review the state of the practice (including experience gained over the past 20 years), propose improved CSL rating criteria and make recommendations for additional assessment, as well as educate the industry on the proper interpretation of CSL test. CSL test results alone should not be the sole means of rejecting or accepting a shaft. A task force of industry exerts was formed to review the existing CSL rating criteria and propose improvements where appropriate. The recommendations presented herein are the consensus of the task force, which believes that they should be incorporated into future criteria, codes and specifications. This paper was produced as a joint effort between the Codes and Standards Committee, the Drilled Shafts Committee and Testing and Evaluation Committee. A task force was authorized under Testing and Evaluation Committee. The task force contributed their expertise in web-based discussions often every two weeks over a period of three years. Interested participants were invited to participate at any time. The document had two rounds of broad industry review, two rounds of DFI Technical Advisory Committee reviews, and a Public Comments process. All comments were considered in producing the final document.

Jan 1, 2019

By Peter Cali, Wesley Schmutzler

"The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.IntroductionDuring hurricane Katrina the levee that constitutes LPV-111 was overtopped and breached in several locations. The United States Army Corps of Engineers (USACE) was presented with the task of increasing the level of the flood protection around New Orleans after Hurricane Katrina to the 100- Year hydraulic grade - the level of protection that provides risk reduction from a storm surge that has a 1% chance of being equaled or exceeded in any given year - and the firm project completion deadline was June 2011.LPV-111 is located in East New Orleans and a large portion of the levee is adjacent to the Bayou Sauvage National Wildlife Refuge. The levee could not encroach on this area. This provided a limited footprint for the levee and made construction of conventional levee difficult, if not impossible. The total length of the project was 5.3 miles. Included in the project was the rehabilitation of one main pumping station and one smaller pump station for water management within the refuge. Short sections of “T” wall were used at the tie in at the Lake Borgne Surge Barrier, the main pump station and the CSX Railroad crossing"

Jan 1, 2017

By Alice Arana, David M. Cacoilo, Joel L. Volterra

"To make space for the new South Ferry Station in lower Manhattan, engineers and contractors carved out a new tunnel beneath three operating subway tunnels and tangentially to yet another tunnel. Creating the space required the design and construction of complex temporary excavation support and underpinning systems and the design and installation of real-time monitoring systems. Construction for the new station and tunnel was mainly cut-and cover in a mixed-face area of soil and rock approximately 2,000 linear ft long, 60 ft wide and up to 70 ft deep. Close coordination between the design/build team and the project owner, the Metropolitan Transportation Authority (MTA), was critical.With the construction of this $400 million project, the MTA and New York City Transit (NYCT) are correcting the numerous physical and operational deficiencies of the existing station and improving the lives of millions of commuters. Built in 1905, the original South Ferry Station is on the IRT Broadway–Seventh Avenue Line of the New York City Subway and is the southern terminal of the #1 subway service, which forms a loop to return uptown. The station has a sharply curved single platform on the outside of the outer track of a two track loop. This platform is short and does not allow the rear five cars of a normal 10-car subway train to load or unload. In addition, once the train stops at the station, commuters wait while retractable floor grates bridge the gap created between the platform and the subway car doors, and then they have only one exit from the station. Spray nozzles keep the tracks lubricated to reduce the train wheels’ friction caused by the tight curve. The sharp curvature of the loop and the inability to use half of the subway car doors slow train operation. With the new ADA-accessible station, 10-car trains will be able to open all doors, and additional entrances, escalators and elevators will greatly reduce travel times."

Jan 1, 2008

By Jean Wehbe, Daniel C. Brahana

"This paper presents a case history of drilled pier construction for a new stadium in Atlanta, Georgia. The stadium structure is supported on several different foundation types, with the heaviest ""mega columns"" typically bearing on drilled pier supported mats. The project includes 141 drilled piers with design diameters of 5.5, 6 and 6.5 feet. The piers bear on bedrock at depths of 20 to 110 feet below the ground surface. Many of the piers included rock sockets with design lengths of 5 to 18 feet. A pre-production drilled pier load test program was completed including one Statnamic load test, two Osterberg Cell tests and two lateral load tests. Non-destructive testing (crosshole sonic logging and sonic integrity testing) were also performed during construction. Production pier installation with over 3800 linear feet of earth excavation and over 1350 linear feet of rock excavation was completed in a little over four months. The piers were installed using both the cased hole method and the slurry method. All cased holed required downhole inspection and slurry holes were initially inspected with a mini-SID device and subsequently by sounding. Advanced drilling equipment and tooling were used to meet the production requirements for the project. This paper reviews the highly variable soil and rock conditions encountered at the site, briefly presents the results of the load tests, and discusses pier installation procedures and the equipment used for installation. The paper also presents conclusions related to the installation and lessons learned.INTRODUCTIONWith the opening of AT&T Stadium in Dallas, a new era of stadium construction began in the U.S. The new age stadiums are larger and have more amenities than their predecessors. The new Atlanta Falcons stadium is no exception. Many of the new features, including Atlanta’s innovative retractable roof, result in extraordinary structural loads. The roof structure is supported by a series of mega columns that bear on eight large caps, six of which are drilled pier supported. Each of the pier caps contains between 8 and 16 drilled piers that bear in the underlying bedrock. The design pier diameters are 6 and 6.5 feet. Augercast piles were used to support two of the mega column caps. Drilled piers, augercast piles, aggregate piers and spread footings are used to support the more lightly loaded portions of the structure."

Jan 1, 2017

By Ken MacLeod

A development at 83 Queens Road in Melbourne, Australia required construction of a three level basement. The normal geotechnical constraints of excavating adjacent to an existing relatively new building were challenging enough for the complicated soils profile occurring at the site. An additional significant challenge faced by the designers, was the requirement to excavate underneath the entire footprint of an existing heritage listed building, known locally as the Mansion, in the centre of the site. Maintaining the structural integrity of that building was afforded the highest priority during the 10m excavation. This paper describes geotechnical aspects of the analysis, design and construction of the secant retention system adjacent the new building and support of the Mansion enabling the 10m excavation to proceed without causing damage to the structure. The secant wall comprised hard-soft interlocking piles constructed using CFA methods. CFA piles along the length of the Mansion provided short term support, with the building load being transferred to the piles by large steel beams jacked under the building. Survey results confirmed that movements of the retaining wall and also the load bearing piles were minimal and well within design expectations.

Jan 1, 2006

By John C. Niedzielski

The PHX Sky Train is a five mile long automated people mover system located at Phoenix Sky Harbor International Airport. Phase I of the PHX Sky Train includes the design and construction of 227 drilled shafts supporting three stations and approximately 9,000 feet of elevated guideway. The guideway includes a 100 foot high, 330 foot long span extending over an active taxiway, which will be the first system of this kind over an active taxiway in the world. The soil conditions in this area generally consist of alluvial Sand, Gravel and Cobbles (locally known as SGC) deposited by the nearby Salt River. The foundation system will support relatively high axial loads, lateral loads and moments due to the height of the guideway above the ground surface, where it needs to pass over existing concourse walkways, bridges, a taxiway and buildings. Drilled shaft design involves designing 4.5-foot to 9-foot diameter drilled shafts within the SGC deposits, most of which extend well below the groundwater table. There is a high potential for collapse of drilled shaft excavation sidewalls within this material. Such extreme design loading conditions, together with difficult ground conditions at the site, result in several challenges for the design and construction of the deep foundation system for the guideway and stations. A load test shaft was designed and constructed as a means to provide site-specific measurement of axial performance under these difficult conditions. Results from the load test were used to reduce the size of the drilled shafts. This paper provides an overall description of the PHX Sky Train project, a summary of the ground conditions, design requirements, load test results and construction methods and equipment used to successfully install the drilled shafts for this project.

Jan 1, 2010

By Douglas Heenan

The fracture orientations were inferred based on theory and previous experience. The fracture pattern was not monitored during the project. Grout volume was recorded at each sleeve port and real time movement monitoring of the building foundation was performed.

Feb 10, 2003

By Brian Isherwood, Tara Brown, Paul Kreycir, Jenny Earle

"The Shangri-La hotel and luxury condominium tower, recently opened on University Avenue in downtown Toronto, required eight levels of underground structure, four extending into the shale bedrock.Isherwood Geostructural Engineers was retained in 2007 by Anchor Shoring Limited to provide an alternative design-build solution to better address serious foundation risks. The site, bounded on three sides by City streets, abuts an existing 1957 14-storey building with five underground levels to the north. Sitting on the rock surface along the east perimeter under University Avenue runs the existing Toronto Transit Commission’s University Subway Line built by cut-and-cover in the 1950’s and which was believed to lie very near the property boundary at the southeast corner of the site.The bedrock under Toronto is known to contain very high locked-in horizontal stresses, much higher than can be resisted by shoring techniques, which result in inevitable wall movement when excavating deep into the rock. The strategy adopted to control the risk to the Subway, adjacent building, and major utilities is described in the paper, along with the comprehensive monitoring of movements, and their comparison to predictions.The ProjectThe 66-storey Shangri-La hotel and luxury condominium tower, recently constructed on University Avenue in downtown Toronto, houses 222 hotel rooms in floors 1-17; 287 residences on floors 18-49; and private estates including two 2-storey penthouses on floors 50-66. These comprise 873,000 square feet of development. Eight levels of underground basement are required to provide parking and other amenities, the lower four extending into the shale bedrock."

Jan 1, 2015

By Arturo Ressi di Cervia

"The Construction of the Thrust Pits for Jacking of the I-90 Tunnel for the Central Artery/Tunnel Project (Part of Contract No. C09A4) in Boston MA was nominated for DFI’s 2002 Outstanding Project Award. In the judging, the project and the specialty subcontractor, Treviicos Corporation, was chosen for a Special Recognition Award. INTRODUCTIONBoston’s Big Dig, as the construction of the underground artery became known, is undoubtedly the largest urban construction project of this century.The Central Artery/Tunnel Project, or CA/T, to call it by its proper name, runs approximately eight miles through the heart of Boston, five miles of which are built underground while maintaining traffic on the elevated existing structure, while at its southern end I-90 is extended to Logan airport under active rail lines, Fort Point Channel and Boston Inner Harbor.Since the alignment of the road closely parallels the shoreline as it existed in colonial times, the cut and cover construction had to contend with substantial portions of filled ground, not to mention existing subway lines, live utilities, building foundations and, last but not least, the irritable Boston drivers and litigious adjacent property and business owners.Consequently, while it is impossible to single out the most difficult or challenging contract, the jacking of the tunnels of I-90 under the live rails of Amtrak certainly will rank high on the list.Never before, anywhere in the world, was an attempt made to jack tunnels of this size: the South Bay Interchange consists of three 78 feet (24 m) wide by 38 feet (11.6 m) high tunnels, the shortest of which is 167 feet (51 m) long. TECHNOLOGYIn order to achieve this engineering feat it was necessary to consolidate the soil under the track to prevent it from moving or settling during the jacking process. After a detailed analysis of the geological profile to be traversed it was decided that freezing was the most suitable method, since it could be applied to the full range of soils present on the proposed alignment."

Jan 3, 2003

By A. V. Rose

A redevelopment in the City of London has been constructed with a piled foundation system that is believed to be the first of its kind. The purpose of the research is to explore this novel foundation method, which involves the installation of closely spaced piles in a perimeter arrangement with a body of soil enclosed in the centre. Both centrifuge modelling and numerical modelling techniques are used.

Jan 1, 2011

By Filippo Leoni, Wesley Schmutzler

"The LPV-111 East Back Levee Improvement Project lies along the Gulf Intracoastal Waterway (GIWW) in Orleans Parish of New Orleans, La., and is an essential component of the New Orleans Hurricane Protection System. The Hurricane Protection Office of the U.S. Army Corps of Engineers (USACE) attributed failure of the New Orleans East levees system to overtopping, erosion and subsequent breaching of LPV-111 along the GIWW, as well as other sections of flood protection during Hurricane Katrina in 2005. The existing levee suffered extensive damages from Hurricane Katrina, such that the USACE elected to provide earth stabilization and to rebuild the levee sections. Due to the adverse geotechnical properties of the foundation soils, the Corps deemed ground improvement necessary to stabilize the new levee and to limit its footprint. Wet Deep Mixing Method (DMM) was selected as the most suitable technology for this task.ChallengesDesign: This reach specifically protects East New Orleans and the Bayou Savage National Wildlife Refuge, the largest urban wildlife refuge in the U.S. and home to several threatened or endangered species of birds as well as many reptiles, amphibians and small mammals. The Corps chose DMM due to the sensitivity of the protected marshlands and because the method limits the footprint of the raised levees. The increase in the load bearing capacity of the treated soil significantly decreases the footprint necessary to attain the required height increase. This limitation required the new levee to have steep slopes, drastically increasing the surcharge on foundation soils characterized by overall poor geotechnical properties (soft clays and peats). The design also considered the increased horizontal stresses on the levees due to the extreme storm surges during a hurricane.The design of the 1.6 m diameter (5.25 ft) DMM elements called for overlapping them to form a double auger element that formed buttresses perpendicular to the levee alignment. The contractor installed the buttresses at a maximum on center spacing of 4.7 m (15.5 ft). One additional double auger DMM element was midway between consecutive buttresses at the centerline of the levee to further help prevent settlement (Figure 1)."

Jan 1, 2013

By Franz-Werner Gerressen

New developments are required each day as our industry becomes more competitive. To improve performance, continue and to ensure future demands can be met. This requires the development of technical support systems that enable a more constant delivery and quality of installation of pile foundations and other applications. For example: assistance systems capable of relieving the machine operator of automating monotonous or repetitive operations. Real time installation control of the production process to manage quality control, or data transfer and reporting systems capable of keeping pace with the digital future. This paper will describe these new approaches and considerations required for these new developments. The paper also describes the equipment which is needed to execute the work under the various conditions and provides references herein. INTRODUCTION The success of a construction site is influenced by a number of factors. Selecting the most efficient and economic methods during the planning phase to defining the right direction. This means having multifunctional equipment available. To ease the usage of this equipment by the operator, uniform operation and control systems are essential. Systems like this can provide uniform handling procedure for more than 20 different installation techniques. Experienced operators are not always available. Therefore, to ease the start for beginners and to support training, numerous assistance systems were developed. This ranges from simple information for controls shown on the monitor avoiding misuse to systems which can partly automate the construction process. Regardless, the best equipment is not enough when the construction is not running smooth. The control system not only helps to organize and coordinate service of the equipment; moreover, it allows the operator to control the quality during the installation process reacting if needed. It allows process optimization as well as documentation which might be required for later negotiations.

Jan 1, 2019

By Peter J. Nicholson

"IntroductionDuring my more than 40 years in the practice of underground construction and engineering, the industry has seen progress from the dig down to rock or hardpan or alternatively drive concrete or steel into the ground and count the blows; then you can be sure of you have a solid foundation; to the modern day, I’m willing to try anything to save money. Of course these are both exaggerations, but not gross ones. After getting bored being supervision on jobs counting blows, I struck out into the new field of “tie-backs” as they were called in the United States, or “ground anchors” as they were then termed in the United Kingdom. After installing some of the first permanent ground anchors for the Corps of Engineers on Lake Michigan as well as the highest loaded rock anchors of the time at two dams on the Ohio River, we were at the top of our game in the 1970’s. Subsequently in the 1980’s when my view of the future of ground anchors saw their installation becoming a commodity item, we branched out into “Pin Piles” now known as Micro Piles, high capacity, steel tube encased, small diameter (5-12” or so), high capacity (100-500 tons) piling. Next came soil nailing, both temporary and permanent retaining walls, as at Cumberland Gap Kentucky. My next morph was into “Cement Deep Soil Mixing” earlier on, known simply as “soil mixing”. For this education I traveled to Japan several times and established a long-term, Joint Venture, relationship with one of the better known Japanese specialty ground modification companies. In Boston at the “Big Dig” we established the then record size soil mixing project, 500,000 or so cubic meters of CDSM concluding in the year 2000. Since then I’ve been involved as a consultant mainly for dams and levees. Below is the story of how I came to be at this place in the road to innovation in Geotechnical processes."

Jan 1, 2017