Search Documents

By Franklin M. Grynkewicz

The subject of bearing pile performance installed by vibratory hammers has been a matter of increasing study and continued controversy. A recent case study from a major bridge replacement project is discussed which provides encouraging data on the use of vibratory pile hammers as a primary means of pile installation and also presents the problems associated with its general acceptance. The bridge project case study foundations consisted of HP 14 x 89 pile sections, designed to develop capacity primarily in friction. Preliminary tip elevations were determined by traditional static analyses. Production pile installation was performed using an IHC S-70 Hydro-Hammer. Driving criteria and final production pile tip elevations were determined after preliminary indicator pile drive tests and static load test results at bridge pier cofferdam locations. Based on impact driven production pile performance, the Contractor wished to investigate vibratory driven piles as a means to accelerate construction schedule. Dynamic pile testing procedures were used as the primary measurement tool and test results were compared to the production pile drive records and prior static load tests. Field testing consisted of driving and monitoring with the PDA impact driven piles to the design tip elevation. Three vibratory driven piles were installed to the same tip elevation and immediately subjected to impact driving and dynamic testing to compare dynamic pile resistance. The results indicated that the site soil conditions were favorable for vibratory pile hammer installation. Recommendations and procedures for proceeding with vibratory hammer pile installation were presented to the Owner. These procedures included quality control in conformance with latest AASHTO recommendations. The Owner, in spite of the site specific data base and QA/QC procedures, would not accept vibratory pile hammer installation, due to the absence of precedence. It is concluded that for vibratory methods to become accepted a rational method of analysis, design and field QA/QC procedures requires development. In addition, the engineering community and Owners/Agencies must be more open to alternate methods of foundation construction. The continued development of dynamic methods of monitoring vibratory pile installation is considered to be key to the general acceptance of this installation procedure.

Jan 1, 1991

By William S. Heckman

a. When to use: high surcharges, vertical capacity required, limit noise and eliminate vibrations, low headroom, eliminate vibration induced settlements. b. Advantages: eliminates impact noise and vibrations, high section modulus if required, vertical load bearing capacity; corrosion resistant, easy to apply facing for use as a permanent wall, adapts to complex wall layouts, would allow top- down construction, very high uplift resistance. c. Disadvantages: spoil disposal, not water tight, cannot penetrate rock and most obstructions, soil can erode between the piles if surface water and ground water are not controlled, hard to install reinforcing beams over 409 long; subject to high negative skin friction loads, high grout takes in rubble and organic soils. e. Relative cost to other systems: 30% to 50% more expensive than driven soldier piles and lagging except when surcharge loads are involved, or the pile cannot be driven due to noise and vibrations. About the same cost as a sheet pile system. Very competitive if high vertical load must be supported by the wall.

Jan 1, 1997

By S. S. Gajin

The paper deals with parametric vibrations of an axially loaded pile. The dynamic model is derived by means of Hamilton's principle and reduced to a partial differen­tial equation with variable coefficients and corresponding initial boundary conditions, taking into account the influence of the axial force. By means of Galerkin's method, the partial equation is further reduced to a Matheu-Hill's matrix partial differential equation of the second order. Since the problem of the dynamic stabili­ty has been expressed only for standing piles, the paper analyses in detail two stan­ding piles, one which is restreined, whereas the other is hinged at the toe. In both cases it is assumed that head horisontal displacement is prevented. Using Ruunge-Kutt's method, a computer analysis in the time domain is given for the characteristic parameters and possible boundary conditions. The paper analyses the stationariness of the process, as well as the dependance of the critical excitation frequency upon the pile parameters. The results have been illustrated by respective diagrams.

Jan 1, 1989

By Bin Zhang

Drilled shafts are a popular type of foundation for transportation applications. They feature the advantages of providing high bearing capacity and generating low construction noise. Advancements in construction technology make it possible to construct drilled shaft with large diameters. In some transportation projects, the full structural loads are carried by a single large diameter drilled shaft; therefore accurately determining the bearing capacity of drilled shafts has important practical and safety implications. The increase of drilled shaft diameter combined with the structure properties of the surrounding soil play in an important role in their bearing capacity. The conventional methods for bearing capacity determination, which mostly come from experience with small diameter drilled shafts, may not work satisfactorily. This paper studies the influence of diameter on the bearing capacity of laterally loaded drilled shafts. Numerical simulations are conducted to investigate the effects of pile diameter on the lateral bearing capacity, especially the influence of shaft diameter and its structural contributions.

Jan 1, 2007

By K. Viking

The vibratory characteristics of full-scale sheet piles, vibratory driven into the ground, have so far not been described systematically in detail. This paper concerns the preliminary results of a series of full-scale field tests where both the driveability and induced ground vibrations have been continuously monitored. Furthermore, the results of measured ground vibration levels have been measured at two different sites characterised as having hard and easy driving conditions. In the light of the presented results, the paper briefly discusses how the complexity of a driveability and vibration prediction can be subdivided into three parts, namely, vibrator-, sheet pile-, and soil-related parameters, all of which significantly affect both the driveability and induced ground vibrations.

Jan 1, 2000

By Bill Starke

The acceptance of AugerCast piles in Canada has been limited. Many engineers are apprehensive about the quality of the piles produced by this method. However, advances in the sensing instruments and computer technology can now provide satisfactory levels of quality assurance. Post construction tests such as the sonic echo method can give an indication of pile shaft integrity. Computerized monitoring of the pile installation process is an immediate and more positive method of quality assurance. The computer continuously measures and records the parameters which indicate the quality of the pile. If these parameters do not indicate a satisfactory pile, it is replaced before the concrete hardens. Computerized monitoring of the installation process is another tool available to the engineer. The data from this system analyzed with soil borings, site inspections, and possibly sonic tests can provide the engineer with enough information for pile certification.

Jan 1, 1997

By Frederick C. Rhyner

This paper describes the design and construction of two high-capacity rock anchors to restrain a supplementary backstay for the Bear Mountain Bridge, which is a suspension bridge spanning the Hudson River about 40 miles north of New York City. The supplementary backstay was installed to relieve a portion of the tension in the southern main cable, which had been creeping in recent years. The two new rock anchors were 1,200 kip capacity each, installed at a batter to depths of 59 feet. This paper describes the subsurface investigation, group capacity analysis, installation and load testing. The rock anchors included strain gages connected to the monitoring system for the bridge. The paper describes the long term strain gage data which shows no change in stress distribution in either anchor.

Jan 1, 2010

By Mait Mets

In Estonia, the deformations monitoring of 1500 buildings are currently under investigation, buildings on pile foundations make up 10 per cent of these. In the following text we will be considering the behaviour of pile foundation buildings in various parts of Estonia, in differing geotechnical conditions.

Jan 1, 2002

By Gyimah Kasali

Rapid Load Testing was performed as part of an extensive drilled pier testing program for the University of California Berkeley Capital Improvement Program. The purpose of the program was to: (1) Verify the axial compressive design capacity values for the planned 24" piers, and to estimate the capacity of the existing 30" CIDH piers, and (2) To evaluate the seismic performance of the proposed drilled shafts. The Fundex PLT was used since the loading period of the PLT is very similar to the period of a seismic event, making it an ideal tool to model the pier response to seismic events. "Performance-based design" of structures subject to seismic loads has been of particular interest to UC Berkeley Seismic Review Committee and the Pacific Earthquake Engineering Research Center. The comparison of static tests to Rapid Load testing also provided valuable correlations. The program represents one of the most comprehensive drilled pier test programs on the West Coast. The testing program consisted of Rapid Load Testing using the Fundex PLT on 6 drilled piers. Rapid Load Tests were followed by conventional static compression and tension tests on selected piers, followed by another cycle of rapid load tests on the statically tested piers. The piers featured extensive instrumentation to allow detailed interpretation of the test result. Correlations were drawn to compare static load test result to that of the PLT in the particular soil profile, and the PLT also provided the data to analyze the ultimate seismic capacity of the piers. The load test results indicate that the ratio of interpreted failure load from the PLT data to the corresponding load from the static load test data is about 1.2 to 1.3 for the clayey soils underlying the test site. The results also indicate that the PLT offers an economical approach to defining the stiffness of drilled pier foundations subjected to seismic loads for use in performance-based design.

Jan 1, 2002

By Timothy L. Roberts

For many years practicing geotechnical and structural engineers in Texas and Louisiana were reluctant to include augered cast-in-place (ACIP) piles as a viable deep foundation alternate. Three primary concerns were the lack of a final driving resistance to confirm adequate capacity, the inability to inspect ACIP piles prior to installation, and the fact that pile integrity is highly dependent on the skill of the ACIP pile contractor's field personnel. The Deep Foundations Institute (DFI) Committee on Augered Cast-In-Place Piles has responded to these quality control concerns by establishing standards of practice for ACIP pile installation and ACIP pile inspection. Regional areas of the country have different subsurface soil and rock conditions and many times this will influence local installation and inspection requirements. The best way structural and geotechnical engineers can address quality control concerns is to be familiar with the DFI standards of practice, to know the special requirements for a particular project site, and to incorporate them into a well-written ACIP pile specification. The purposes of this paper are to: 1) review the main fundamentals of a successful quality control program, 2) describe how these fundamentals can be applied to the installation of ACIP piles, and 3) add personal experiences from ACIP pile projects in Texas and Louisiana. Nondestructive test methods are frequently used as a quality control tool to evaluate questionable piles. An additional brief discussion of two nondestructive test methods is presented to complete the paper.

Jan 1, 1998

By H. Mori

The session chairman, Dr. H. Mori, welcomed the delegates to Discussion Session 8. AUTHORS PRESENTATIONS 1 . G. Price, Building Research Establishment. UK Mr. Price expanded on the content of his paper and presented elements of various case histories of bored piles instrumented by the Building Research Establishment. In particular, the interpretation of data from instrumented piles is critically related to: (i) the construction process (ii) concrete stiffness and variability (iii) the effects on the pile due to installing instruments The main role of the instrumentation in the examples presented was to establish pile performance under service loading conditions. Of particular interest is the mobilisation of skin friction and soil shear modulus.

Jan 1, 1991

By Rob Jameson

"Although seismic retrofit is recognized as a key micropile application, widely-used reference documents do not clearly address design and testing recommendations for micropiles that are loaded primarily under seismic conditions. The principles of micropile design and construction and their application to seismic retrofit projects are well understood and executed by leaders in the field. As the micropiling market grows, a wider audience relies on the information presented by DFI and similar industry groups. State-of-practice updates appear periodically in conference proceedings, but examination of recent bid documents makes it clear that there are opportunities to improve the specification of load, deflection, testing and acceptance criteria on many seismic retrofit projects. Updates to the FHWA Manual or DFI Sample Specification that specifically address seismic retrofit cases would be useful tools to disseminate information and enhance the state of practice.Micropile Survey UnderwayAs one step in this process, I am distributing surveys to contractors and designers prior to DFI Super Pile ’09 (June 4-6, San Francisco) seeking recommendations for design and testing procedures applicable to seismically loaded micropiles. I am also requesting any existing references that could be promoted as a standard for these cases. Anyone interested in participating in this survey, should contact me at rjameson@malcolmdrilling.com. Seismic RetrofittingMicropiles are ideally suited to seismic retrofit applications. Their high-tensile and compressive capacity can sustain the large concentrated loads induced during seismic events. They can be installed within and around the access limitations of existing structures, and can be drilled through and grouted into the wide variety of soil and rock materials encountered in seismically active zones.Seismic retrofits have included micropiles since the early 1990s, and they are now widely specified in the Western U.S. In the San Francisco Bay Area alone, thousands of micropiles have been installed for seismic upgrades of highway and transit aerial structures, and retrofits of commercial, residential and public buildings. Micropile use is growing in both public and private sectors, with large-scale retrofit projects currently underway for both the Bay Area Rapid Transit (BART) system-wide upgrades and renovations at San Francisco Airport."

Jan 1, 2009

By Liqun Liang

Various nondestructive testing (NDT) inspection methods are available to evaluate the structural integrity of cast-in-place shafts. The widely used methods include Cross Hole Sonic Logging Testing and Low Strain Testing. Due to its advantages such as low cost, easy operation, quickness and flexibility (no need to plan ahead and prepare inspection tubes or other devices), Low Strain Test is frequently specified in quality assurance programs of many countries or when doubts arise as to the integrity of the finished shafts/piles. The method is well suited for small to middle sized shafts. However it is an indirect NDT testing method and has certain limitations. Data interpretation requires proper training, experience and judgment and, therefore, inconsistent conclusions and reporting may be provided by different testers. To avoid or reduce such inconsistencies, it is best to follow a standardized data interpretation and record classification system. In this paper, a new classification method is presented with examples. A step-by-step data evaluation and interpretation procedure is proposed with examples of real cases to help understand the LST data. The paper also makes recommendations for measures to be taken when anomalies are detected in tested production piles.

Jan 1, 2011

By Onur Guvener, Kalaiarasi Vembu, C. Vipulanandan

"Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.INTRODUCTIONAugered cast-in-place piles (ACIP) are drilled foundation installed by drilling a hole with a continuous flight auger to a predetermined depth. Non-displacement Augered Cast-in-Place (ACIP) piles are increasingly used for supporting building, bridges, sound barrier walls and many other structures around the world. In an ACIP pile, depending on the soil type and rate of the auger advance, ground stresses are maintained near the value that existed before construction by using a continuous flight auger, which is never withdrawn until the cementitious material (fluid Portland cement grout) is placed by pumping the grout beneath the withdrawing auger under pressure through the hollow stem of the auger (Vipulanandan, 2005). ACIP piles are typically installed with diameters ranging from 0.3 to 1.0 m and lengths up to 30 m (Brown, 2005) although longer lengths have occasionally been installed. Comparing to the drilled shafts and driven piles of equivalent size ACIP piles can be installed more rapidly with fewer disturbances to the surroundings in favorable geological conditions. Hence the installation procedure and the quality of material used in the construction have significant effects on the behavior of ACIP piles (Vipulanandan, et al. 2007). In this paper construction quality control technique for ACIP piles was investigated. Load displacement and load transfer behavior of pile in compression and tension in hard clay was also studied. The development of side resistance in compression and tension for the load test piles and the reaction pile were also investigated."

Jan 1, 2017

Jan 1, 1998

By Bas R. Hemmen

GeoBrain is a facility at GeoDelft with the purpose to provide society with all relevant geo-engineering knowledge and experience in a structured way. On the basis of the available knowledge and experience engineers, decision makers and construction supervisors can come to a fast, reproducible and objective choice, taking into account the consequences. The paper presents examples from the GeoBrain experience databases and forecasting models developed for foundation engineering and directional drilling, or: "GeoBrain Foundations" and "GeoBrain Drilling". GeoBrain is closing the gap between theory and practice. It is aimed directly at reducing uncertainty and the costs of failure, thereby increasing the quality of profession and minimising the risk in geo-engineering works.

Jan 1, 2006

By George Filz, Morales, Carlos, Bertero, Filippo Maria, Alessandro, Leoni

"The Deep Mixing Method (DMM) represents a viable solution to improve adverse geotechnical properties of foundation soils for many practical applications. A pre-construction soil investigation campaign is necessary to assess soil properties and to retrieve samples of different soil layers for a laboratory Bench Scale Testing program (BST). The BST has to be designed using various binder types, binder contents, and water/cement ratios in each of the soil types. Following the laboratory program, a full scale Field Test (FT) is typically necessary to verify the results of the BST. This paper will highlight the differences and the importance of performing both pre-construction laboratory tests and field tests to ascertain the proper mixing parameters in the different soil layers. Comparative analyses and interpretations between the lab and field stages, along with accumulated information about soil properties and quality control (QC) results, allow fine-tuning the production parameters throughout a project. Three Deep Mixing Method projects, where both laboratory and field tests were executed, are illustrated: (1) The LPV 111 Project (New Orleans, LA, USA): DMM was used for ground improvement/foundation strengthening to stabilize and support the burden of a new levee raise; (2) The Rio Puerto Nuevo Project (San Juan, PR, USA): DMM was applied to improve the soils adjacent to a 90"" forced sewer main relocation and to improve the soils for the base of a new drainage channel; and (3) State Road 83 (US 331) over Choctawhatchee Bay project (Walton County, FL, USA): DMM was applied to stabilize the causeway sections of the bridge enhancement project. Data recorded during laboratory and field tests for these projects were analyzed and interpreted to select the most appropriate construction parameters to provide a final high-quality product.INTRODUCTIONThe Deep Mixing Method (DMM) represents a viable solution to improve adverse geotechnical properties of foundation soils in many situations. The effectiveness of working parameters depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product.Generally a pre-construction soil investigation campaign has to be performed to assess soil properties and to retrieve samples of different soil layers for the laboratory Bench Scale Testing programme (BST). The BST has to be designed using various binder types, binder contents (or cement factors - CF), and grout water/cement ratios (W/C) in each of the soil types; the selection of the different combinations and dosages for the BST is based on past extensive experiences on similar materials. Following the laboratory programme results, a full scale Field Test (FT) has to be designed and executed, installing several DMM elements to verify the results of the BST and fine tune the construction parameters, with the appropriate binder type and dosage and the most effective equipment and tool configuration."

Jan 1, 2015

By Sam X. Yao

The underwater concrete technology has historically evolved largely through a trial-and-error process of constructing marine works. Many outstanding examples exist of high quality concrete placed underwater. However, failures also occurred and led to excessive cost and/or schedule overruns. These failures were largely due to improper concrete mix design or improper placement. The problems may have occurred because proper underwater concrete construction techniques and experience have not been widely disseminated. This section focuses on technical issues of underwater concrete mix design, concrete production and placement, and quality control.

Jan 1, 2013

By Y. K. Wong

This paper describes in detail various problems concerning the construction of a pile-raft foundation supporting a 42-storey tower block. The subsurface generally consists of highly weathered sedimentary rock. A comprehensive instrumentation program is implemented to monitor the behaviour of the foundation system throughout the construction period of the superstructure. Instrumentation observations are highlighted in the second half of the paper.

Jan 1, 2010

By Rick Ellman, Ian Chaney

"The Hampton Roads area encompassing the Norfolk, Virginia Beach and Newport News metropolitan region experiences some of the worst traffic congestion in Virginia. With continued growth of the ports and increasing demand, the Virginia Department of Transportation (VDOT) initiated the Downtown Tunnel/Midtown Tunnel/MLK Expressway Project, a complex undertaking critical to addressing the Hampton Roads area’s transportation needs. The project is a $2.1 billion Design/Build/Finance/Operate (DBFO) endeavor most notably involving the construction of a new two-lane vehicular tunnel utilizing the Immersed Tube Tunnel (ITT) method. The tunnel will pass under the Elizabeth River parallel to the existing Midtown Tunnel between Norfolk and Portsmouth, Va. It will be the largest design-build project constructed in the history of the Hampton Roads District.The New Midtown Tunnel will extend approximately 6,450 ft (1,966 m) along the north side of the existing tunnel where it ties into the existing Midtown Tunnel approaches in Norfolk and Portsmouth. It is being installed in a pre-excavated trench of which approximately 2,250 ft (686 m) required bracing on the Portsmouth side and approximately 1,000 ft (305 m) required bracing on the Norfolk side. The remaining 3,200 ft (975 m) of trench excavation was open cut dredging with laid back side slopes, optimized to reduce dredging, disposal and backfill quantities while also reducing the risk to the existing tunnel. The braced excavation portions of the tunnel alignment were divided into distinct segments which include: Portsmouth Approach Boat Section, Portsmouth Approach Cut-and-Cover Section, Portsmouth Dredge Section, Norfolk Dredge Section, Norfolk Approach Cut-and- Cover Section and the Norfolk Approach Boat Section. All “approach” excavations were performed in the dry and all “dredge” excavations were performed in the wet. Eleven ITT segments are being fabricated in the Sparrows Point Dry Dock facility in Baltimore, Md., and each 14,000 ton (12,700 tonne) segment is being towed approximately 220 mi (354 km) to the site. The ITT segments will extend under the Elizabeth River, with the deepest crossing 90 ft (27 m) at the Federal Navigation Channel. Once beyond the channel limits the ITT rises at an approximate 4.5% slope. Controlled screeding and element lowering operations will be performed primarily from floating barges."

Jan 1, 2014