Search Documents

By C. M. Lesher, R. R. Keays

"The komatnte-associated Fe-Ni-Cu sulphide mineralization at Kanihalda, Western Australia, is generally believed to be magmatic in origin, but a number of postmagmatic processes significantly modified the original distribution, structure, texture, mineralogy and chemistry of the ores. Two important types of mobilized magmatic sulphides are interpillow/interbreccia sulphides and hydrothermal vein-type sulphides. Interpillow and interbreccia sulphides occur interstitial to pillowed or volcaniclastic footwall metabasalts beneath or adjacent to the stratiform contact ore horizons. They are mineralogically and compositionally similar to massive ores (and are similarly depleted in PGE relative to the compositions of bulk samples of mined ores), but normally do not contain the distinctive chalco-phile ferrochromites characteristic of contact ores. They are interpreted as magmatic sulphides that have been mobilized from the overlying or adjacent massive sulphide layer during peak tectono-nietamorphism.Hydrothermal sulphide-quartz + albite veins also occur in the footwall metabasalt and contain unannealed deformation fabrics indicative of emplacement during retrograde metamorphism. The high Ni and Pd contents of these sulphides (7-13% Ni, up to 70 ppm Pd) indicate that the metals have been derived from the spatially associated komatiites and/or contact ores, consistent with the Pd depletion previously inferred for massive ores. Very low Ir contents and high Pd/Ir ratios of the vein-type sulphides confirm an aqueous transportation-deposition mechanism; hydrothermal transfer of PGE results in strong decoupling of Pd from Ir.There appears to be a complete continuum of sulphide mobilization at Kambalda ranging from whole-scale phy sical dislocation (fault offset ores) and selective mobilization (stringer sulphides) through nietamorphie replacement (interpillow/interbrec- cia sulphides) to jiydrothermal dissolution and redeposition (vein-type sulphides)."

Jan 1, 1984

By Groom P.

The wastage of timber in coal-mines that is caused by decay is very great; in fact, far greater in this country than is generally realized. Mr. E. W. Peters estimates that of the whole wastage of timber in mines in the United States of America, 50 per cent, is due to decay and insects; of this 50 per cent, an overwhelming part is due to decay. The most efficient methods of decreasing this grave loss can be devised only by co-operation of the mining engineer and the scientific expert, and it is partly in the hope of procuring such collaboration that this paper is written. It contains, therefore, a resume of our present knowledge of the decay of wood, and of the economic methods of checking this in mines; but, with a view to improving those methods, it also directs attention to the gaps in our knowledge and the means by which these can be filled by future investigation

Dec 1, 1916

By R. I. Jeffery, J. W. Summers

An account is given of the verification and calibration of a numerical modelling technique that has been developed for the prediction of subsurface strata deformation following the extraction of coal by longwall mining methods.

Jan 4, 1992

By B. W. Hester

Report of discussion at January, 1971, general meeting (Chairman: M. J. Cahalan, President) of the paper published in Transactions/Section B (Applied Earth Science), vol. 79, May, 1970, pp. B60-B67, and contributed remarks. Comments were made by Taylor J.T.M., James C.H., Lethbridge R.F. and Heath K.C.G.

Dec 1, 1971

By A. Sutherland Strachan

Before regulations governing the work on the mines, it was not uncommon in the Rand for a miner to die within a period of 2-3 years as the result of exposure to dust. This paper considers mine and tunnel conditions promoting silicosis and measures to avoid dust exposure in the Rand, South Africa.The relationship between blasting and lung lesions is explored. Evidence is presented that improved working conditions and lowered dust levels reduce the incidence of silicosis.

Jan 1, 1947

By Z. Sawlowicz

Finely dispersed, primary sulphide mineralisation in the Cu-Fe sulphide zones of copper-bearing shale of the Polish part of the Permian Kupferschiefer is mainly present in the form of framboids and spherules. This type of mineralisation is especially well preserved in organic-rich shale, where it often dominates over a later diagenetic mineralisation that consists of large grains and veins. In microscopic observations special attention was paid to composite grains of copper and iron sulphides. The results suggest that the Cu-Fe and Cu sulphides precipitated in the Kupferschiefer sediment before pyritisation of the framboids had ceased and that they replaced metastable precursors of pyrite. The precipitation of copper sulphides could have been delayed owing to the formation of Cu-organic complexes.

Jan 4, 1992

By G. Merrington, B. J. Alloway

Tailings from three historical mining areas in the UK were leached in columns under a simulated weathering programme which was chosen to represent periods of 1 and 2 years at 3 different ambient temperatures. The total concentrations of Cd, Cu, Pb and Zn in the primary ore minerals present in the tailings showed only a limited correlation with metal concentrations in the leachate. The leachate from columns of tailings that were maintained at a temperature of 25 (+/-3) degrees C contained, on average, 50% more Pb and 75% more Cu than leachate from tailings that were maintained at a temperature of 10 (+/-3) degrees C. The pH values of leachates from all three types of tailings at 25 (+/-3) degrees C were 0.2 units lower than those from columns maintained at 10 (+/-3) degrees C. The concentration of Cd and Zn in the tailings leachates showed no marked difference at the different temperatures. The composition of the leachate was found to be dependent on the type of gangue mineral, the presence of other sulphide minerals and the formation of secondary iron minerals. A comparison of the concentrations of heavy metals in the leachates produced in the laboratory with those in leachates that were collected in the field over a similar period of time from two of the mine sites showed that concentrations were of a similar order.

Jan 8, 1993

By D. D. Lei, H. Sevim

Long-term production planning in open-pit mines requires the determination of cut-off grade, mining and milling production rates, a mining sequence, mine life and ultimate pit limits. Since these variables interact in a circular fashion, a genuine solution to the problem necessitates their simultaneous determination. A methodology with this capability is described. This comprises a group of heuristic algorithms and an unconventional dynamic programming algorithm. The method is demonstrated using data for a gold deposit in the western USA

Jul 1, 1996

1994 estimates for Porgera are probable and proven reserves of 58 200 000 t of ore grading 5 g/t Au. Gold mineralisation is related to an intrusive complex emplaced at shallow levels in poorly consolidated sedimentary rocks. The complex is located in a zone of fold-and-thrust deformation, whose formation may have been initiated shortly before emplacement and continues locally today. Abundant primary magnetite in the complex gives an intense, 5 km wide aeromagnetic anomaly. The deposit formed during two main stages of mineralisation, the first related to early magmatic-hydrothermal activity and the second representing later epithermal overprinting centred on the Roamane fault. Hydrothermal alteration followed closely on emplacement indicating a close genetic relationship between magmatism and mineralisation. Both stages of hydrothermal activity post-date and overprint early propylitic alteration. Several factors have acted in unison or sequentially to concentrate metals at the deposit, including an extensional or trans-tensional tectonic setting within an arc or collisional environment, the exsolution of a magmatic hydrothermal fluid prior to sulphur saturation in the melt, the development of the hydrothermal system into one favourable for transporting gold, the action of late-stage faulting in focusing epithermal fluid flow, and the role of dissolved gases in promoting fluid phase separation and high-grade ore deposition

Jun 19, 1905

By Winmill T. F.

The previous papers have been concerned only with the atmospheric oxidation of coals from the Barnsley Seam, for which it has been shown that an adequate explanation of the origin and nature of gob-fires can be based on the reaction between the coal itself and the oxygen of the air without the intervention of any other substance. It becomes of importance, therefore, to ascertain how far a similar explanation will hold good for spontaneous heating in other seams, and with this object in view samples including anthracite and lignite have been taken from a considerable number of pits in different parts of the UK (south Wales, Northumberland and Durham, north Staffordshire, Portrush and Ayrshire), some liable to fire, others not. There is abundant evidence to support the commonly-accepted view that spontaneous heating is due to the heat evolved during the absorption of oxygen from the air by coal or pyrites. The quantity of heat produced by the reaction has been measured and it has been shown that the observed rate of heating of a sample of coal agrees with the rate calculated from the heat of reaction and the rate of absorption of oxygen

Dec 1, 1916

By D. J. Wall, T. D. Johnson, M. T. Parry, G. R. Heath

In coal-fired power stations coal is ground to a fine powder and then transported pneumatically at 25-30 m/s velocity to remote burners. Wear of the conveying pipework is a well recognised problem and traditional lining materials are Nihard and basalt. In many cases these are being replaced by alumina tiles in order to improve life and reduce the frequency of replacement. A programme of laboratory testing of candidate aluminas with AIO, contents between 85% and 99-5% has been undertaken and the results compared with field experience. This gives confidence in the erosion tests, which were designed to replicate most of the field conditions. However, it has not proved possible to draw correlations between the laboratory erosion rates and any of the materials’ bulk properties. SEM, TEM and microanalysis studies have therefore been made in order to look for microstructural aspects that could be influencing erosion rates and it has been shown that intercrystalline cohesion, the matrix phase and porosity appear to have most influence on wear performance. It is necessary to quantify these microstructural parameters if reliable erosion performance is to be obtained. This paper was read at the Institute of Ceramics Annual Convention at the University of Durham, April 1988.

Jun 12, 1905

The paper, presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, presents experimental work undertaken to observe the quenching effect of different substances, to find the most efficient of these substances, and to arrive at a possible explanation of their preventive action. The coal-dusts experimented with were such as passed through a 100-mesh sieve (10,000 holes to the square inch), and were obtained by grinding the coals. The quenching substances, used in as fine a state of division as possible, included gypsum, dried Chance mud, quicklime, magnesia, magnesia alba (levis), anhydrous sodium carbonate, sodium bicarbonate, soda-crystals, Glauber salts, ground shale and boiler-ashes

Dec 1, 1916

The report of the Annual General Meeting of the Institution of Mining and Metallurgy held on Thursday, 20 May, 1971, in the rooms of the Geological Society of London, Burlington House, Piccadilly, London, W.1, at 4 p.m. (Chairman : M. J. Cahalan, President) includes details of awards and prizes presented to William Justin Kroll, Sir Gordon Colvin Lindesay Clark, John Convey, Evert Hoek, Peter Reginald Dawson and Christopher Michael St. John

Dec 1, 1971

By Marshall Charles Riddell, John Carlon

local news

Jan 12, 1997

By B. D. Rayment, J. D. Wilson, G. R. Davis

Wheal Jane, situated between Truro and the Carnmenellis granite, is under development by Consolidated Gold Fields, Ltd., as a tin producer. The main or B lode comprises a complex cassiterite-sulphide ore located in shear zones along the footwall of the lowest of a series of porphyry dykes (elvans) which strike ENE and dip 35° north. Minor mineralisation follows other elvan contacts and sets of later steeply dipping fractures. The localisation and overall geometry of the deposit is explained in terms of the complex structural geology of the Lower Palaeozoic metasediments and the shape and manner of emplacement of the invading Hercynian granite of Cornwall. Variations in the thickness and grade of the orebody, and in the nature of the mineralisation, are shown to be structurally controlled by undulations of the footwall contact of the B elvan. Wallrock sericitisation is present and is applied in exploration for ore

Dec 1, 1971

Jan 1, 1947

Discussion following the presentation at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, included the author's introduction, written contributions by Bedson P.P., Gregory T.W.D. and Morgan J.D., oral contributions by Louis H., Greener T.Y. and Severs W., and the author's reply

Dec 1, 1916

By E. C. I. Hammerbeck

"Geological controls and constraints in space and time define the milieu of the nickel deposits of Southern Africa. Primary, magmatic deposits are of two types, e.g. synvolcanic or syntectonic deposits confined to certain orogenic domains, and those related to intracratonic, post-orogenic magmatism, e.g. the Great Dyke, the Bushveld Complex and the Insizwa intrusion. Epigenetic and supergene deposits form a separate, unrelated group and are of minor economic importance.The metallogenic evolution of syntectonic nickel deposits is particularly well illustrated in the Zimbabwean Province, where the relationships between Archaean greenstone development and nickel mineralization are best illustrated. Volumetrically subordinate, nickel-poor greenstones in the 3500 m.y. old Sebakwian Group are followed by more common komatiite development in the Lower Greenstones (3000 m.y.), and, finally, by very significant komatiites with important nickel mineralization in the 2700 m.y. old Upper Greenstones of the Bulawayan Group. Comparable nickel mineralization is not known in the Raapvaal Province, in spite of ubiquitous komatiitic magmatism of the Onverwacht Group (3500 m.y.) and other greenstone sequences. No komatiitic rocks younger than about 3200 m.y. are known in this region, orogenic activity in the Kaapvaal tectonic province having ceased at about 3100 m.y., whereas the Zimbabwe Province remained tectonically active until at least 2600 m.y.The tectonic environment, host-rock petrology and mode of emplacement, as well as some details of the nickel mineralization, are the parameters employed to classify the Southern African magmatic nickel deposits. A rating of the deposits is introduced that reflects the original resources of the deposit, its average nickel content, its mining history and potential to facilitate ready comparison with and assessment of the nickel deposits listed in the classification, as well as some important nickel deposits worldwide."

Jan 1, 1984

By R. R. Liebenberg, M. I. Brittan

The kinetics of the copper segregation process has been investigated. The experimental strategy used to isolate the rate-controlling reaction step is described. This step was found to be the chloridisation of the oxide copper minerals in the ore. The link between the rate of chloridisation and the overall rate of segregation is demonstrated experimentally. The influence on the kinetics of the various parameters in a TORCO system is examined and the implications are discussed

Dec 1, 1971

By J. Plant

Stream-sediment sampling undertaken to define the regional geochemistry of northern Scotland is described with particular reference to the errors involved. The region is underlain essentially by Moine schists, Caledonian granites and Old Red Sandstone sediments, which are generally characterized by low geochemical relief. Factors in the secondary environment obscure the relationship between trace-metal concentrations in stream sediments and bedrock geology. Investigation of sampling and sample preparation methods indicates that the -100-mesh material is the optimum size fraction for the regional survey of this area: it provides adequate geochemical contrast: it reduced the incidence of spurious high values in the samples investigated and it is available in amounts which are adequate for all the analyses required. Grinding samples improves precision and reduces the preferential volatilisation of metals coprecipitated with hydrous manganese and iron oxides for the optical emission spectroscopic method used initially. A study of the dispersion of metals in the drainage system of an area of Pb-Ba-Mo mineralisation and an area of U-Pb mineralisation, respectively, indicates that a sampling interval of 1 per 2 km2 based on second- or third-order streams is adequate to define anomalous metal concentrations. Regional variation can also be represented on the same interval. Modifications to the sampling procedure to reduce the effects of the secondary environment are complicated by the primary association of Mn and Fe with mineralisation in the area. The ratio of analytical and sampling error to regional variance shows that procedural precision is adequate to prepare regional geochemical maps of northern Scotland, with the exception of Cr, Cu at low concentrations and Pb.

Dec 1, 1971