Search Documents

By M. J. Scoble, L. M. Daneshmend, C. Hendricks

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. An attempt is made to relate emerging technologies to education and training requirements by examining the nature of the Canadian mining industry's human resources. Particular attention is given to the trends evident in mine automation and their likely impact on instructional needs. The characteristics of "computer-aided instruction" systems are reviewed and related to the implementation and support of mine-wide monitoring and communication networks, which are seen as fundamental to the eventual automation of underground hardrock mines

Apr 1, 1994

By A Cox

It has been demonstrated that all the cadmium from spent batteries, typically 4 g per battery, can be recovered by burning polyvinyl chloride waste to yield hydrogen chloride; this reacts to produce volatile calcium chloride, which can then be condensed and collected in a separate reactor. Alternatively, chlorine may be used to chlorinate the cadmium with equal efficiency. There is also a prospect of using very low concentrations of these gases, less than 1%, to effect the separation. The Cd was recovered more quickly when exposed to sustained, controlled flow rates of chlorinating gases, whereas when PVC was burnt most of the gas was produced in a very short time, not allowing complete reaction. This problem can be overcome by recirculation of the gas into the reactor. The technology is efficient and clean and the equipment used is simple, enhancing the prospects for a pilot-scale version of the process

Jun 21, 1905

By S Colak, M Tunc, C Celik, M. M. Kocakerim

The most important parameters affecting the solubility of ulexite (sodium calcium borate) in H2SO4 were found to be reaction temperature and solid:liquid ratio, in that order. Dissolution increased with increase in temperature and stirring speed and with decrease in solid:liquid ratio, particle size and acid concentration, the last effect as a result of decreased precipitation of CaSO4 on unreacted particles. Optimum conditions, in which around 99.5% of the ulexite could be dissolved, were a reaction temperature of 60 degrees C, a solid:liquid ratio of 1:8 g/ml, an acid concentration of 8 mol/l, particle size smaller than 425 micrometres, a stirring speed of 52.33/s, a reaction time of 1 800 s, a calcining time of 3 600 s and a calcining temperature of 170 degrees C. These conditions, determined by the Taguchi method, are reproducible in a commercial production environment

Jun 21, 1905

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. Phases of the Ir sub-group are present either as inclusions in or interstitially to chromite and are unaffected by (or only altered in situ during) hydrothermal processes. By contrast, almost all phases of the Pd sub-group are located in a secondary textural setting - in fractures in chromite or between fragments of brecciated chromite. The different settings indicate that the mineralisation episodes were associated with magmatic and hydrothermal stages respectively. The presence of an included Pd-group mineral in a hydrothermally Pd-group mineralised chromitite sample suggests that the hydrothermal Pd-group minerals were at least partly derived by remobilisation from magmatic deposits in the chromitite pod. These observations indicate that Pd-group elements are more mobile than Ir-group elements under hydrothermal conditions and point to the potential for hydrothermal platinum and palladium mineralisation in favourable environments

Apr 1, 1994

By G. G. Barbante

The oxidation behaviour of selenide matte with a substantial Cu content and low Ag differs significantly from that of high-Ag matte. Low-Ag selenide mattes display a large oxygen solubility and the upper boundary of the miscibility gap in the Ag-Cu-Se-O system is depressed to quite low Se contents. As a result, the formation of Ag metal is considerably delayed. The oxidised selenide matte, low in Se and with a relatively high oxygen content, has previously been termed oxymelt. With further oxidation, its composition enters the misciblity gap and crude Ag is formed. The sodium silicate slag captures very little of the SeO2 and the dissolved Ag2O(s) content of the slag is relatively small, with a Raoultian activity coefficient of 0.57. This value was found to be independent of the slag's Cu2O content

Jun 19, 1905

By P. Golledge, A. D. S. Gillies

An investigation has been carried on samples of three Queensland coal dusts to determine the potential explosibility of dust-gas mixtures. The explosion potential of the samples was classified by the lean and rich limits of explosibility and the limiting oxygen concentrations for each sample. Plotting of these points showed 2-dimensional flammability limit surfaces for coal dust/oxygen, methane/oxygen and coal dust/methane mixtures. From these plots the 3-dimensional flammability envelopes defining the explosibility of the mixtures were defined. The explosion limits of the coal dust/methane/oxygen system were seen to be influenced most by the explosibility characteristics of coal dust. Methane exerted a stronger influence over the explosion limits when the coal had a low volatile content

Jun 19, 1905

By L Zhang

The Chinese coal industry is the largest coal producer in the world. The total production in I995 was 1.28 bnt. On the way towards introducing a market economic system, this mature industry is facing major challenges. The main problems are a large surplus of manpower, shortage of current assets and capital, low productivity, high casualties and a huge deficit. This paper discusses the present situation and the future developments in the Chinese coal industry. The current policy can be stated as ‘rapidly developing the state collieries and improving the village and private mines; integrated development to achieve an economic operating scale and encouraging a diversified economy; rapidly exploiting and developing in the North west and South west; promoting productivity and efficiency; welcoming multi-sources and types of investment; setting up coal exchange markets; and the careful control of resources and the environment'.

Jan 11, 1996

By F. M. Vokes, P. M. Ihlen

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Ore deposition was related to three major stages: continental rifting and separation (Vendian-Late Cambrian), convergence (Late Cambrian-Early Silurian) and collision (Early Silurian-Devonian). The first stage included deposition of volcanogenic massive sulphide Zn-Cu and stratabound or stratiform Fe and Zn-Pb(-Cu) on continental margins, as well as less economic Nb and Fe in carbonatites, U, Mo, Ni and V in Alum Shales and orthomagmatic Cr, Fe-Ti and Ni(-Cu). The numerous volcanogenic massive sulphides formed during convergence included Early Ordovician Cu-Zn, mature-arc Cu, Zn, Pb and Fe-oxide deposits, Besshi-type deposits dominated by Cu or Zn in gabbro-intruded sediments and minor Cu-Ni(-PGE), Cu-Mo and skarn deposits. The collisional stage is represented by epigenetic deposits including sandstone Pb deposits (Pb, Zn, Ba, F and Cu) and minor vein deposits with variable Au, Ag, Pb, Cu, Zn, Fe, As, Sb, W and Mo

Jun 19, 1905

The Aredor mine employs conventional dragline methods to exploit alluvial diamond deposits. Production began in 1984 with the policy of mining in the terrraces during the wet season and in the river flats during the dry season. Early production failed to meet predicted grades. A major geological programme to re-evaluate existing reserves was undertaken. This resulted in considerable increases in reserves in the river flats. Many of the reserve blocks included flats on both banks of the Baoule river. Methods of access into the river flats, normally flooded in the wet season, were developed to allow mining throughout the year. River diversions have been the main method used to provide access into the reserve blocks and, most importantly, to remove the risk of flooding. Aredor has carried out six main river diversions with a total length of 12 km. The diversions allowed production planning to be made on the basis of the economic evaluation of the reserve blocks, without undue regard to natural ground conditions or to seasonal factors. The Manning equation was used for the calculation of channel dimensions and gave satisfactory results. The practical aspects of the diversion preparations and flooding prevention are described

Sep 1, 1991

By R. A. D. Pattrick, R. A. F. Ixer

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. At Calliachar Burn, 14 steeply dipping quartz-sulphide veins, with and without gold, infill master joints that crosscut gently dipping metasediments and metabasics of the Pitlochry Schist Formation. The wallrock is extremely bleached and enriched in sericite, chlorite and carbonate. Gold grades vary from high with quartz-galena-pyrite to low with galena-chalcopyrite; the gold forms electrum inclusions smaller than 20 micrometres in pyrite or, rarely, arsenopyrite. At Urlar Burn, gold is present in small amounts in 4 quartz-galena-chalcopyrite veins. Although much of the mineralogy is similar to that at Calliachar, there are significant differences in Sb-, Te-, Bi- and Hg-bearing phases. Fluid inclusion data suggest mineralisation occurred over the range 320-140 degrees C, from fluids with significant CO2 and 2-13 wt% equiv. NaCl. Mantle-derived fluids appear to have been generated during the late Caledonian and focused by the Urlar Burn fault

Jun 19, 1905

By F. C. Gennari, D. M. Pasquevich

With the gradual exhaustion of natural rutile, there has been extensive research into its synthesising from lower-grade titanium minerals. The removal of Fe from pseudobrookite (Fe2TiO5) by chlorination was studied, using both isothermal and non-isothermal thermogravimetric measurements. Correlation of the results obtained from element distribution maps, scanning electron microscopy, energy-dispersive X-ray analysis and phases detected by X-ray diffraction in the chlorinated samples showed clearly two associated processes. First, the pseudobrookite particles reacted with chlorine and iron was removed selectively as FeCl3(g), leaving a solid residue rich in the TiO2 phases anatile and rutile, separated from an inner layer of unreacted pseudobrookite by a distinct interphase boundary. Second, chlorine allowed TiCl4(g) to form in the reaction bed, where it removed iron from the Fe2O3 crystals as FeCl3(g) and substituted Ti through a pseudomorphic reaction

Jun 21, 1905

By A. Ersoy, M. D. Waller

The principal factors which require consideration in predicting drilling rates are the bit-type, the bit operating parameters and the characteristics of the penetrated rock. A single index is not a sufficient basis for predicting performance. A variety of rock types were drilled in the laboratory with polycrystalline diamond compact (PDC) and impregnated diamond core bits using a fully instrumented drilling rig at different rotational speeds and with a range of weights on the bit. Quantitative determinations of a wide range of textural, mechanical and intact rock properties were also made. Multi-variable linear regression analysis was then used to develop predictive models of rates of penetration from the operating and rock property data. The models have been verified by statistical tests. The analysis indicated that the models for the pin and hybrid PDC bits have potential for practical application. However, although the model for the impregnated diamond bit appears to be reasonable from a purely statistical point of view, it may not be satisfactory for drilling uses as it is based on two measures of rock hardness alone. The application of multiple regression analysis to PDC drilling performance is novel and the technique shows promise for the prediction of rock drillability with PDC bits. The ability of the technique to provide a mathematical characterisation of the performance of new drill bits in specific rocks may prove to be of value to drill manufacturers and users

Aug 1, 1995

Paper presented at the UK minerals industry conference and published in: Minerals extraction towards the millennium. UK minerals industry conference, 3-5 April 1995, University of Leeds. London: Institution of Mining and Metallurgy, 1995. The various types of risks that arise in minerals industry projects are usually financial, technical, or environmental, and the key to valid risk analysis is complete integration of all risks, both within and between categories. Geographical information systems (GIS) and geostatistical simulation methods can provide a means of integrating data and conducting realistic risk analyses. Risk can be quantified but there are limitations to numerical approaches to risk assessment. Realistic quantification requires adequate models of the processes that give rise to risk. Risk perception must also be taken into account when conducting risk assessment and reporting the results, especially in public forums. The modelling and visualisation capabilities of a combined GIS/simulation system can provide the means of dealing with perception in risk analysis

Jun 19, 1905

By F. Boudreault, M. J. Scobie, J. Szymanski, C. Hendricks

The development of new stoping methods and more effective control over dilution, recovery and fragmentation depends on improved accuracy in blasthole drilling. The mechanisms and factors which control accuracy are poorly understood. Canadian blasthole stoping and the practices adopted for monitoring and controlling drilling accuracy are reviewed. The techniques and problems associated with blashole set-up and trajectory surveying are discussed. Four new blasthole trajectory survey systems are evaluated on the basis of their performance in recent underground trials. Conclusions are drawn as to the technological developments required so that more precise control over drilling accuracy can be achieved.

Jan 12, 1992

By J. A. Finch, D. Lin

The robustness of the large-sections correction procedure, Hill's fast approximation, Barbery's correction and the PARGEN correction was examined by comparing their ability to reconstruct the true liberation distribution using sectioning data from computer-generated spheres. The results indicate that the flexibility of a correction procedure is related to the assumptions it makes about the continuity of the liberation distribution, locked-particle characteristics and ore texture. Overall, the large-sections procedure appeared to be the most generally applicable. The Hill fast approximation performed well, but this was probably because it partially incorporates the sphere model; the performance of the PARGEN and Barbery corrections varied from case to case.

Dec 1, 1995

By G. S. Pauley

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993 (original title: Case-based reasoning can be a catalyst for improvement). A new computer software technology known as Case Based Reasoning (CBR) can be used to produce small decision support systems that are economically viable. This is because the knowledge that they contain can be owned and maintained by their users. A CBR tool has been used to perform a pilot study with Anglesey Aluminium Metal Ltd. The results are encouraging. They suggest that a combination of CBR and participative design and implementation techniques (such as Checkland's Soft System Methodology) can achieve sustainable improvement in mineral processing functions. An explanation is presented of why traditional, rule based systems are often an ineffective way to implement support systems. It is shown that CBR may provide an appropriate technology solution. Methods of achieving sustainable benefit are indicated. The pilot study with Anglesey Aluminium Metal is used as a practical illustration of the development of a CBR application. A review of potential application areas and some observations about the implementation are presented

Apr 1, 1994

By T. B. Colman

Paper presented at the MEP '89 conference held in Madrid, 13-15 November 1989. Britain has sustained an important metalliferous mining industry over many centuries. Recently, new geological concepts and exploration techniques have indicated that there is considerable potential for the discovery of a variety of deposit styles, often in previously neglected areas. The recent discoveries at Aberfeldy (Ba-Zn-Pb), Gairloch (Cu-Zn) and Cononish (Au-Ag)in Scotland and Curraghinalt (Au-Ag) and Lack (Au-Ag-Pb) in Northern Ireland are illustrations of this potential. Some of the prospective areas for future exploration are described and an indication is given of the legislative framework within which mineral exploration and development are carried out

Jan 1, 1991

By M J. Thomson, P T. Burgin

The economic growth of Hong Kong and adjacent territories in Southern China is, to a considerable extent, dependant on air transportation, but the present Kai Tak Airport is incapable of expansion to meet future needs. After years of study, agreement was reached to build a new airport on the island of Chek Lap Kok, some 34 km remote from Hong Kong, with an ultimate capacity of 87M passengers and 8.9 Ml of cargo per annum. Apart from the building of the airport and its associated infrastructure (including a new town), other similar massive construction works have been necessary in the form of land reclamation from the sea and existing outer lying islands. The construction of bridges, tunnels, railways and highways are also an integral part of the project. The paper provides a broad overview of the concepts of the scheme (called The Airport Core Programme) and highlights some of the major operations and equipment being used in the projects, whose cost at 1992 prices was reckoned to he Hong Kong (HR)$l63hn.

Jan 7, 1997

By A. R. Naderian

Laboratory strength and deformation testing of freshly blasted sandstone and claystone overburden from Jeebropilly colliery in Queensland and in-situ plate-bearing tests on four backfills of different ages showed that the bearing capacity of backfill is a function mainly of compaction, not of age. The modulus or stiffness of the backfill is significantly increased by previous loading, in some cases up to threefold. Backfill material experiences some compaction through the passage of mining vehicles, likely to provide a bearing capacity that will support normal construction activities; the limited testing performed suggested that completed backfills are capable of supporting loads of up to 200 kN/m2 while sustaining displacements acceptable for a wide range of residential and industrial uses, but may be susceptible to collapse settlements due to saturation in the long term

Jun 19, 1905

By E R. Hassall

Discussiong the importance of minerals and mining, impacts on the environment and remediation, and the need to foster interest in science among young people.

Jan 8, 1997