Search Documents

By R Tom Watts

The blasting industry has changed more in the last five years than in any period to date. The equipment utilized to load boreholes has changed in response to more precise blasting products and programs, and the need to maintain tighter control over product formulations produced by bulk loading equipment. Tread Corporation has built over 1,300 heavy ANFO type bulk loading units currently operating in over 40 countries worldwide. These units have been designed to meet almost every possible loading scenario but there are always new situations that require special designs and configurations to meet the challenge. The focus of this presentation is to make you aware of the process that should be used to determine the equipment best suited for your application. We will discuss loading cycle times, delivery rates, multiple product mixing capability, capacities, manpower utilization, regulatory compliance, and where and when to use automation in the loading process. We will also discuss the suitability of chassis with regard to ground pressure, turning radius, terrain, weather conditions as well as highway suitability. The US Bridge Law as well as laws that cover the concept of axle loading and spacing will be covered. Through new computer aided design and modular design capabilities, you can now have almost any configuration required to meet your bulk loading objectives. We will also review the range of equipment currently available in the market place and discuss tradeoffs between price, capacity, and complexity.

Jan 1, 2000

By Pierre De Pasquale, Aquilino Antonio Alvarez-Castro

Greenhouse gas emissions are now an essential issue for extractive industries. Actually, lowering of quarry energy consumption and CO2 emissions participates to answer both environmental and financial issues. The “EE-Quarry” European project, supported by the European Commission (EE stands for Energy Efficient), develops a new and highly effective modelling and monitoring Energy Management System technique to improve Energy Efficiency and move to a low CO2 emission rate in the nonmetallic mineral industry.

Jan 1, 2016

By Mansour Asri, Philippe Somogy, Youssef Daffi, Amor Karim

Very few cases of Cast Blasting use in phosphate mining are reported. However, in open-cast coal mining, Cast Blasting is a common practice. And yet, the geological structure of both types of deposits is similar. Accordingly, advantages for phosphate open-cast mines are manifest, especially as future conditions of phosphate deposits fit quite well with the approach.

Jan 1, 2015

By Zou Dingxiang

Rock blasting in the project of “Site Formation and Associated Infrastructure Works at Choi Wan Road and Jordan Valley” is the largest urban blasting project in the history of Hong Kong and also is rare in the world. More than 6.2 million of in-situ rock has to be excavated by blasting. The site is located in the center area of eastern Kowloon peninsula, surrounded by highways, registered cut slopes, high-rise residential buildings, MTR subways and the public utilities. The complex situations bring great difficulties and risks to the blasting works. A bird-view photo of the site is shown on Picture 1.

Jan 1, 2007

By N. Jayaraman, V. Srikant, A. Radhakrishna

Addition of a 500 MW unit to the existing units at Ramagundum Thermal Power Station requires blasting of large volumes of rock very close to sensitive installations like Turbo generator, Generator transformer and Power cycle equipments. Levelling of the areas and excavations for footings are, therefore, to be carried out cautiously. The existing sensitive installations should be protected against ground vibrations and flyrock. The paper describes the details of a few of the many blasts carried out successfully wherein the ground vibrations were restricted and flyrock was avoided.

Jan 1, 2003

By Douglas Bartley, Brian Wingfield, Robert McClure

Recent studies and limited tests indicate favorable results utilizing high accuracy electronic detonator technology over conventional non-electric pyrotechnic systems. This study discusses the application of this technology using the Daveytronic programmable system in an on-going production basis. The study quantifies the performance as it relates to fragmentation, excavation, vibration and productivity in an eastern U.S. aggregate mining operation. In order to insure accurate data, tight field controls were adhered to during the drilling and blasting process as they related to blast design, bench preparation, pattern layout, drilling and blasthole loading. Following the blast the excavation and crushing procedures were studied to quantify any down stream advantages due to improvements in fragmentation. This study will help provide the industry with information as to the advantages of high accuracy electronic blasting systems over conventional pyrotechnic systems and show the results of an operation utilizing electronic detonator technology through their production season.

Jan 1, 2000

By R. Franfield

This paper describes a situation that many drilling and blasting contractors have found themselves in – a client?s fear of the use of explosives. In the summer of 2007 Blasting Services Ltd was asked to undertake some drilling and blasting work in an abandoned quarry that was being restored for a housing development. Previous quarrying operations had left a series of overhangs that were considered unsafe and required removing. The site contractor considered that the best and safest way to carry out this work was by drilling and blasting. Blasting Services Ltd, with the technical assistance of Exchem Explosives, designed a drilling and blasting regime to accomplish this work with a series of trim blasts. The design took into account the close proximity of a structure in very poor condition and the imposed vibration limit of 6.0 mm/s (0.24 i.p.s.). The faces were profiled, holes drilled and explosives ordered. A few days before the first blast was due to be carried out the client decided that the poor condition of the nearby structure meant that the use of explosives could not be permitted. This decision was made despite the blast design indicating that the vibration level would be well below the 6.0 mm/s (0.24 i.p.s.) limit.

Jan 1, 2009

By Daniel Hauer

Blocking. (5) The “blocking” of boulders is a much cheaper way of breaking them up than “mud capping.” It should always be used in preference to that method except when too much time will be consumed by a crew of men waiting for the drilling to be done, as shown in example of cost No. 1, as given under “mud capping.” Under such circumstances the time consumed would be a greater cost to the contractor than the extra amount of dynamite. Then, too, on large thin boulders to drill one hole would result only in breaking the stone into such pieces as would again have to be broken; and the many holes might equal the cost of extra dynamite. Under such circumstances if method (6) cannot be used, “mud capping” will have to be resorted to, to do the work economically.

Jan 1, 2006

By Charlie Adcock, Rob Farnfield, Andy Wetherelt

The ISEE Blasters Handbook gives guidance on the level of air overpressure likely to cause occasional window breakage (151dB) and general window breakage (171dB). A long-term safe level of 140dB is also suggested. This guidance is widely used by demolition and other contractors to assess damage zones in the region of explosive applications employing unconfined charges. Other reference material gives more detailed guidance relating to window area, aspect ratio and glass thickness. Despite the guidance given in these references, complaints by members of the public regarding window breakage continue to be received by explosives engineers from air overpressure levels well below the longterm safe limit. Such complaints are not limited to the use of unconfined charges but can even be generated from the highly confined use of explosives in quarry blasting. This paper describes a series of experiments with explosive charges fired in unconfined conditions close to various window configurations. The aim of the work was to test the existing guidance levels and to extend the knowledge base in this area. Topics covered include the role of differential pressure across windows in the walls of an enclosed space such as a room.

Jan 1, 2006

By Peter Duniam, Stephen John Brace

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation and Explosives Applications Orlando,Florida,USA July24-27,200O. Objectives:- After completing this session 1. Explain safety issues 2. Do simple initiation design 3. Describe how the system works 4. Demonstrate scanning, hookup, testing and firing 5. Describe hot to do a post blast check 6. Explain how to treat misfired detonators

Jan 1, 2000

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By Detnet Solutions

1. “Daisy-Chain” concept The term “daisy-chain” stems from the fact that when the HotShot? detonators are connected there is a chain or electrical path for electrical current to flow from detonator A to detonator B, detonator B to detonator C etc until the path is terminated by an electrical means. The “daisy-chain” concept has long been used in electronic detonator systems, historically used in Expert Explosives’ ExEx 1000 5/6 wire system and currently in use in African Explosives Limited (AEL’s) Electrodet? electronic detonator system and has been adopted as the basis upon which the “auto-programmability” of the HotShot? electronic detonator system functions. HotShot? Detonators are connected to each other in a string, completing a “daisy chain”, and during the auto-detection mode of the control equipment, it is possible for the equipment to determine the order of hookup of the detonators as well as map the entire blast layout. The auxiliary components (Row Controllers & Branch Controllers) assist the control equipment in mapping the entire blast by indicating different points on the blast, i.e. The inflection point of a row of blast holes on a closed chevron timing pattern, the beginning of row of blast holes on open chevron timing pattern and extra blast holes or extra blast rows.

Jan 1, 2004

By Nolan Eckroade, Nigel Pereira

Wireless electronic blasting systems are a new technology that enable truly wireless initiation through rock, air and water. This is achieved using low frequency magnetic induction waves to wirelessly send a firing command to groups of in-hole primers. Fully wireless initiation not only removes the limitations imposed by a wired connection to each primer in a blast, but also enables users to alter the paradigm of conventional mining techniques to advance operational productivity and reduce personnel exposure to high-risk activities. While initially deployed in underground applications, wireless electronic blasting is now being used in the open cut environment. To capture the early impacts in surface mining operations, case studies conducted at three surface mines evaluated blasts utilizing a wireless electronic blasting system against baseline blasts using conventional, wired initiation systems. The purpose of this paper is to outline the specific learnings associated with wireless electronic blasting in surface mining to date. The paper will include references to these specific case studies as well as benefits realized and applications for the future.

By Gabsoo Kim, Rulin Yang, Dave Kay

Blast vibration data, such as PPV are usually scattered. In many cases, plots of PPV versus the charge weight scaled distance are so scattered that useful trends from different blast designs cannot be identified. The scattering of the data may be attributed to the inaccuracy of the PPV measurement, the definition of the scaled distance from a multiple-hole production blast, and the measurement of distances and charge weights. The error from vibration measurements is one of the major contributors to the scattering of the plots. If accurate monitoring is conducted, improved design options may be identified. This paper documents two case examples that compare different vibration sensor couplings. The first case shows mounting accelerometers at spots that protrude from the ground, compared with the sensors that were mounted on a flat ground surface. The second case compares data from loose-sand buried geophone with that from sensors coupled to the ground using concrete blocks.

Jan 1, 2014

By J A. Singer, S R. Iverson, C A. Link

High resolution seismic refraction tomography has proved to be a useful tool to effectively estimate depth of blast induced damage in a mine face. Excavation blast damage can be as shallow as 1 to 2m and requires resolution at a fraction of a meter for effective imaging. We used an accelerometer with flat frequency response to 1000Hz to record data at spacings of approximately 0.25 to 0.5m along mine walls. First arrival times from the seismic data were used to produce P-wave velocity tomograms. The tomograms show transition from low velocity zones to velocity associated with competent rock. We interpret the low velocity zones to indicate residual fracturing from blasting. Experiments on a concrete test block and at two underground mine locations give results that are consistent with fractured rock transitioning to competent rock. Our method can be applied efficiently in an underground environment to provide continuous velocity information with depth into a mine wall over a span of approximately 10m.

Jan 1, 2009

By Michael S. Wieland

"Toxic fumes cause fatal andnonfatal incidents in underground mining, where the working environment tends to trap the fumes, hindering the restoration of non-harmful conditions. Workers can underestimate the residual fume toxicity and return to the work site too quickly. The toxic fumes from charge explosions depend upon a number things: formulation ingredients, mixture uniformity, water resistance, hole contaminates, rock hardness, and dust interactions. Transitory hole-to-hole waves can cause partial desensitization, ruin the reaction kinetics, and worsen the fume toxicity.Traditionally the toxic fume hazard for a candidate explosive is resolved from a requisite tally of fume components. The resolution starts with the fume spectrum, a tabulation of specie concentrations, transformed to standard reference conditions and readjusted to remove the air dilution. The resultant influence, which is referred to as relative fume toxicity RFT, is deduced by a formula rule with some chosen constants and the requisite concentrations. The RFT result is normally compared to an RFT criterion that represents the worst-case (maximum) tolerable fume toxicity, as stipulated by regulations or otherwise."

Jan 1, 1997

By Joshua Hoffman, Braden Lusk, Kyle Perry

This study explores how different geometries affect the shock tunnel’s performance and is broken down into three phases. Phase 1: Open arena testing in which theoretical energies produced by the detonation of small (<1.0 kg) charges are compared to actual experimental values. Phase 2: Shock Tunnel testing in which realized energies are experimentally recorded for the UK and S&T shock tunnels. Phase 3: Analysis of the data to begin building a pressure-forecasting tool for the UK shock tunnel given the explosive characteristics, sample size and desired pressure and impulse.

Jan 1, 2009

By Connie Postupack

The purpose of the workshop is to show the effect of various blasting factors on the overall results.

Jan 1, 1994

By Greg Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified geologically sensitive due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the geologically sensitive area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model.

Jan 1, 2018

By Jim Mikelait

Overview ?? Why do we need security? ?? Needs assessment ?? Elements to any security system ?? Protect, Detect, Alert, esponse ?? Electronic Security System Criteria ?? Advantages and Limitations of Various Security Options ?? Internal measures to protect against potentially harmful employees ?? How can technology improve my business?

Jan 1, 2006