Search Documents

By David G. Paton

"Electromagnetic surveys were conducted at the BXL Bulk Explosives Limited Mixing Plant andsurrounding area to characterize runoff from the site and possible impacts of salinity. The BXL Plant is located at the edge of a depressional area and any escape of soluble ions, such as nitrates, would have ended up in the slough to the west of the plant. Two electromagnetic (EM) instruments were used in the survey. A Geonics EM 3 1 was used in October 1997 and in June 1998, a new multifrequency instrument, a GSSI GEM 300 was also tested. Both instruments were individually mounted on a plastic sled with Teflon runners and towed with an ATV quad. Position was determined using a Trimble Pro XL global positioning system (GPS) with a real time correction mode Landstar receiver for an accuracy of about *l m. Both GPS and EM instruments were set to collect data at 1 second intervals. The quadrature maps for both instruments showed essentially the same information, namely of very high conductivity, appearing to emanate from the mixing plant. The levels of conductivity were highest where the saline water appeared to pool, at the southern end of the slough. Soil sampling locations were identified from the EM maps and navigated to using the real time GPS. Composite samples were collected by hand using a Dutch auger, from two locations, in increments of O-1 5, 15-30, 30-60 and 60- 90 cm. The analysis of the soil samples indicated a complete absence of nitrate or ammonium ions; the major anion was sulphate, indicating naturally saline subsoil conditions. The GEM 300 made the collection of data more efficient, as only one pass was required to collect the data from four depth intervals. The EM survey combined with the real time GPS allowed rapid characterization of the site with respect to soil salinity and proved to be cost-effective for Phase l/ Phase 2 site assessments and targeting sampling locations."

Jan 1, 1999

By H Russell

An account of an experimental blast at the Sullivan Mine involving a small pillar drilled with 4 1/2" diameter up-holes, and loaded with emulsion explosives from a truck-mounted tank/pump unit.

Jan 1, 1984

By Young-Dong Cho, Han-uk Lim, Bok-Ki Park, Sang-Eun Lee

Many methods and techniques have been developed to reduce ground vibrations. Some of them are an adoption of electric millisecond detonators with a sequential blasting machine and an improvement of initiating system with an adequate number of delay intevals.

Jan 1, 1995

By Lex L. Udy

External detonation generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating explosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall.

Jan 1, 1977

By Michael Wieland

The work principle from thermodynamics is used to model the shock and heave for explosives shot in rock or under water, with the latter compared to reported results. The work principle utilizes restrictions and constraints to yield a representative fit to the irreversible (natural) shooting process. The reduction of the internal energy of the reaction-zone yields the total expansion work (TXW), the resultant sum of the rock/water shock and heave. The restoration technique of forming a closed thermodynamic loop yields the reversible mechanical work (RMW) or the rock/water heave. The residual work that remains when RMW is subtracted from TXW yields the irreversible disorder work (IDW) or the un-dissipated (without loss) shock in the surrounding rock or water. The work principle renders an unequivocal relationship for the shock-loss factor, rather than the traditional roundabout formula for correcting the underwater gauge-shock of un-modeled explosives. There’s a novel heave-ratio factor that unquestionably rates the fit of results under comparison. Rock-shots are more complex in nature than underwater shots due to rock fracture and stratum rupture, though numerical resolution is worthwhile. The proposed rock-water-jelly (RWJ) model yields rough estimates, with rock-type results not wholly different from their underwater counterparts. Though reported underwater shots reveal shock and heave trends with respect to charge formulation ingredients, there are no such rock-shot results for comparison, since the relevant test measurements in rock remain difficult, if not intractable.

Jan 1, 2007

By Conny Postnpaok, Mark E. Hammele

"A major problem that has continued to plague the surface oil industry is blast induced damage to the coal seam. Atlas Powder Company has addressed this situation through several years of field research in full-scale production environments. Many operations across the United States havebeen evaluated ."

Jan 1, 1989

By Hideaki Kitajima, Ryo Sakamoto, Katsuya Sasaki, Maehata Hidehiko

The Electric Discharge Impulse Crushing System (EDICS) is a technology for carrying out crushing by using electrical power and nitromethane. It is designed for construction tasks such as splitting of concrete and rocks.The EDICS consists of an electric discharge generator that supplies a high-voltage high-current pulse, a cartridge that generates power by using electric discharge energy, and cables that connect the electric discharge generator and the cartridge. The cartridge contains a thin metal wire that evaporates because of the electric discharge energy and a nitromethane that reacts with this evaporated metal wire. The cartridge can be used to generate a high pressure on the order of gigapascals within a time interval of several hundred microseconds, and crushing power equivalent to that generated by explosives is generated during this period. In recent years, the EDICS has been widely used in Japan because of its good performance and favorable characteristics.

Jan 1, 2011

By Stephen H. Chung

Direct visualization of rock movement during blasting is an important key to understanding the blasting process, as well as optimizing blast designs and explosives performance. To achieve this, a digital camera system (HSIS-500) has been built. It is a custom made high speed solid-state camera employing an advanced charge coupled device (CCD) and dynamic random access memory (DRAM) technologies. It handles like a regular video camera but requires no film or tape as the image is recorded in digital form on memory chips and transferred to the system hard disk for storage. The system consists of two components: the camera body and hardware, and the image processing unit.

Jan 1, 1996

By Robert A. Cummings, Francis S. Kendorski, Charles H. Dowding

During the summer of 1980, a field project was carried out to determine the stability of the beautiful and dramatic natural limestone pinnacles (locally termed "Hoodoos") at Bryce Canyon National Park, Utah, when subjected to ground motions and airblasts resulting from proposed strip coal mine blasting. The concern arose from environmental considerations associated with the proposed development of a large coal strip mine which would approach within 4 miles of the park. The pinnacles range up to 150 ft in height and are quite slender, producing a fragile appearance. The remoteness and ruggedness of the area required a field camp, and 4-wheel drive vehicles, helicopters, and snowcats for support. Portable magazines were necessary to store the more than 7 tons of blasting agents and explosives required. In conducting the blasting, great attention was paid to environmental impacts. In the field, a target pinnacle was selected and instrumented with mechanical strain gages, and research seismographs that required helicopter placement.

Jan 1, 1982

By Lars Osen

Both fragmentation and safety can be improved by following proper procedures in loading boreholes. Proper loading procedures such as primer location, borehole sealing, decking, and stemming along with the hazards of dropping on primers are presented. Discussions follow on the reason for the use of each procedure along with the possible consequences such as hazards, misfires, or poor fragmentation.

Jan 1, 1985

By Charles Zdazinsky

Back-break induced from blasting is a concern in open pit metal mining because it compromises the conditions of the pit’s final walls. Final walls that have excessive blast induced damage commonly require extra attention and can often lead to increased cycle times. Most importantly however, the safety conditions of a back-broken region can be significantly compromised and it must be addressed to prevent injury and/or damage to equipment. This occasionally results in the necessity to alter mine plans to prevent an incident from occurring in a back-broken region which can be costly to the mine.

Jan 1, 2014

By Sharon K. Reamer, Klaus G. Hinzen

A series of controlled seismic experiments was performed in a limestone quarry in southern Germany to study seismic effects of cylindrical charges fired in both a half space (HS) (burden 63 m) and quarter space (QS) (burdens of 3 and 3.5 m) geometry. Charge columns contained from 20-32 kg of explosives and initiated from the bottom. The explosives formed a cylinder 4 m (20 kg) and 5 m (32 kg) high and 90 mm in diameter at depths from 3-8 m below ground level. Prior to each of the larger explosions, small charges of 0.12 kg seismogelit were fired at 4 m and 8 m depths in the same boreholes. Seismograms were obtained from 23 three component surface stations and up to 10 three component borehole stations (6 m depth). For each experiment, stations were located on three linear profiles of length 72 m at different azimuths from the source and one semicircular profile at a constant range of 30 m.

Jan 1, 1991

By Graeme Exelby

The 4" Wassara water hammer was originally developed by G-Drill AB together with Swedish Mining Company LKAB for their underground long hole production drilling. Sandvik Rock Tools AB is responsible for the introduction of Wassara worldwide.

Jan 1, 1998

By Calvin J. Konya

For proper blast design, one must make the assumption that all blastholes release nearly ideal energy. In many types of blasting operations, blastholes release very little useful energy. These blastholes are called malfunctioning blastholes. Recent studies indicate that as many as 30 percent of all blastholes are malfunctioning. These malfunctioning blastholes are not an unusual occurrence.

Jan 1, 1988

By Dale S. Preece

A carefully designed and controlled in-place destruction experiment was performed on a concrete bunker buried in 4.27 m (14 ft.) of soil. The objective was to determine if the explosive charges would collapse the structure in-place without requiring mechanical excavation. Collapse of the buried structure was fi rst attempted by drilling holes in the soil and placing four 13.38 Kg (29.5 lb) Comp B explosive charges at a depth of 2.13 m (6.7 ft.). The confi guration of the charges when detonated was 2.13 m (6.7 ft.) off the top of the concrete roof and 3.66 m (12 ft.) apart in a square pattern. Detonation of these charges created a crater ~4.88 m (16 ft.) in diameter and 2.13 m (6.7 ft.) deep, leaving ~2.13 m (6.7 ft.) of soil covering. Very limited spalling occurred on the ceiling of the concrete structure as a result of detonating these four charges. The second attempt to collapse the structure consisted of placing another single 13.38 Kg (29.5 lb) charge, identical to the fi rst four, near the geometrical center of the bunker roof. This charge was detonated in the soil cover 100 to 200 mm (4 to 8 in.) above the reinforced concrete roof, collapsing it. Due to the collapsed roof and remaining soil cover, the structure had been collapsed in place, requiring no further demolition. A computer simulation of the above explosive destruction scenario was completed using the computer hydrocode AUTODYN with a granular material model to treat the soil and the RHT brittle material model to represent the concrete. AUTODYN accurately recreated the scenario including the slightly damaged response of the concrete structure to the initial four charges and the collapse of the structure resulting from the second single charge close to the roof.

Jan 1, 2007

By Hapsari Rosa, Ross Cowie

Conventional blasting activities in the mining process use various types of explosives, with the primary raw materials being Ammonium Nitrate and diesel fuel. The quality and specifications of the two raw materials significantly affect the performance of explosives. One program from the Indonesian Ministry of Energy and Mineral Resources requires mixing 30% Bio Diesel 30 with 70% diesel fuel oil in several industrial sectors, including mining, to reduce greenhouse gas emissions and stabilize CPO prices. This program aims very well for environmental sustainability and the palm oil business. However, it turns out that this change impacts the performance and results of the blasting process in the mining industry, which is the appearance of fumes. This paper will discuss the tests carried out in the laboratory on Bio Diesel 30, the explosive products used, and rock samples were taken from a mine in East Java, Indonesia. The aim is to determine what factors can cause fumes utilizing a mixture of Bio Diesel 30 with pure diesel fuel. The parameters tested were visual differences, infrared spectrometry, density and viscosity, surface tension and contact angle for Bio Diesel 30, stability test for explosives, and the SEM-EDS method for rock samples.

Feb 6, 2023

By Michael Swisdak, John Tatom

In a quantitative risk assessment (QRA), the ability to accurately model real-world situations is obviously critical. In the end, the model must be able to represent the effects produced by the detonation of the donor and the consequences on the target. The science that goes into such a model must be carefully thought-out and based on as much data as possible.

Jan 1, 2007

By Jerry R. Wallace

This project consisted of blasting for expansion of a major interstate natural gas transmission pipeline pump station. The pump station handled 400-500 million cubic feet (11-14 million cubic meters) of gas per day.

Jan 1, 1996

By Zhang Qi

For the most part, the flying piece is serious endangerment in the demolition blasting. To prevent the endangerment, a large number of materials are needed as the protection. Therefore, the determination and design way of the flying distance of piece in demolition blasting have been concerned extensively. Previously, the experienced or half experienced formula was adopted to calculate the distance of the flying pieces. The calculating values of the distances of flying pieces are not identical with the practice results. The problems concerning the design way of flying distance of pieces are researched in the paper.

Jan 1, 1994

By Dennis A. Clark, Richard E. Calvin

As the scarcity of mineral resources increase and subsurface mining activities expand along with simultaneous surface mining in coal, industrial minerals and rocks, along with metals, the need to insure safe conditions is paramount.

Jan 1, 1981