Search Documents

By Alan Hooper

This paper and slide presentation is a brief rundown on what is probably the worst natural devastation I have ever witnessed. The epicenter of the quake that so violently shook Mexico City occurred 230 miles away near Mexico's west coast. The first calculation placed the quake at 7.8 on the Richter scale. This was later upgraded to 8.1. Each unit increase on the Richter scale indicates about a 30 fold increase in energy released. The quake was felt in much of Mexico and south Texas and damage occurred in many other Mexican cities. On the morning of September 19, 1985, at 7:18 A.M., the ground went into motion and shook for approximately 2 to 4 minutes. During this period most of the devastation occurred. At 7:38 P.M. the following day, the second quake hit and more buildings fell from this 7.5 quake. The ground in Mexico City moves like jello since it is a dry lake bed 7,350 feet above sea level.\

Jan 1, 1986

By U. Prasad

This paper summarizes the investigation carried out on a wide range of rock types, subjected to high velocity impact to simulate explosive action. A Split- Hopkinson Bar apparatus was used to generate the high velocity impact. The rock samples included both homogeneous and isotropic, and anisotropic types. The strain rate achieved was between 600 and 12OO/sec, The respective measured dynamic compressive strengths were compared with their low strain-rate or static values. It was found that the ratio of the dynamic to static values ranged between 2.5 and 4.6. It was also determined that the high strain-rate loading produced finer fragment size distribution than the static loading. The fragment size distribution from the two strain-rate regimes has been further analyzed to establish correlation with rock types and the strength characteristics. The results also confirm that high strain-rate loading (i.e. high detonation pressure and high velocity of detonation in an explosive column) would significantly affect the degree of fineness in a blast.

Jan 1, 2001

By Thomas E. Lobb, Harry C. Verakis

Blasting is a primary means of extracting minerals and ores at surface mining operations. The domestic consumption of explosives and blasting agents during the year 2001 was about 5.25 billion pounds. Flyrock is always a major concern for the blaster. Flyrock from surface blasting operations has caused serious injury and death to employees and other persons. Injuries due to flyrock and the lack of blast area security accounted for over two-thirds of all blasting-related injuries in surface coal, metal, and nonmetal mines during the period 1978-2002. Selected accidents due to flyrock and lack of blast area security in surface mining are presented in this paper. Incidents related to construction blasting are also described. Techniques to mitigate blasting accidents are discussed. These include proper blast design, driller-blaster communication, inspection prior to loading and firing the blast, removing employees from the blast area, controlling access to the blast area, and using a blasting shelter. An experienced driller could detect potential problem areas such as voids, mud seams, incompetent rocks, and other irregularities by observing the progress of drilling. The drill log should include the details of any unusual or exceptional circumstances noticed during drilling. A blaster may need to alter the loading configuration to alleviate potential problems. Basic blast design is sometimes taken for granted and assumed to be proper for the conditions encountered, but one size does not fit all. It is known from the physics of blasting that the explosive energy takes the path of least resistance. The path of least resistance could generate flyrock, depending on the blast site conditions. A combination of ‘borehole tracking’ and ‘laser profiling’ can assist in improving the design of a blast. The blaster can use these tools to adjust borehole loading to match site conditions.

Jan 1, 2004

By Lawrence Mirabelli, William Hissem, Gary Veltrop

Capital Quarries Company, Inc., Jefferson City MO produces aggregate products for road base, asphalt, concrete and concrete block. With their production quantities small in comparison to those produced by the goliaths of the aggregate industry, they find it necessary to constantly stay on the leading edge of best practices for cost control, process and production improvement to sustain a successful business. In the words of Eric Strope, President, “The safety of our employees is foremost. They all work hard each day. They are focused on keeping our cost to manufacture down. As I see it, we cannot work any harder so we must work smarter!”

Jan 1, 2009

By Donald H. Matthews

The Society of Explosives Engineers is an international organization of over four hundred members involved in the explosives industry, with most members being active in the United States. The regulations imposed by regulatory agencies on the explosives industry have drastic effects far beyond the industry. Since explosives are used in mining, manufacturing, construction, entertainment, and art, all phases of man's activities, including fundamental needs for survival, are affected by how efficient the industry uses explosives. We, as members of SEE, must be sincerely concerned with both the quantity and quality of government regulation, and this paper spells out some of the problems caused by regulations and offers a solution.

Jan 1, 1980

By Jeff Friedman

This paper addresses certain problems to be encountered when a blasting contractor agrees to provide indemnification. Nearly 100% of all blasting work is performed pursuant to a contractual agreement. Whether the explosives engineering firm works directly for the property owner, or for a general contractor by way of subcontract, indemnification agreements are generally required to protect owners, operators, general contractors, and other interested parties in the event there is subsequent litigation. These contractual requirements are typically referred to as indemnification and “additional insured” agreements. We will address the ramifications of contractual indemnification as well as “additional insured” agreements in this presentation. Some of the aspects of this paper will include:

Jan 1, 2004

By E. Contestabile, B. von Rosen, P. Lightfoot

As part of an accident investigation ANFO was subjected to various abusive tests. A tractor-trailer carrying 18,000 kg of blasting explosives, caught fire, burned for approximately 30 minutes, and then detonated. A series of tests was designed to observe the behaviour of ANFO when subjected to different thermal stimulus tests and more specifically, the Height-to-Detonation Test. Three diameters of steel pipes were used in the Height-to-Detonation Tests thereby simulating cylindrical columns within a pile of ANFO. The ANFO samples were then subjected to various thermal stimuli to initiate a reaction. Through the use of some instrumentation, the response of large ANFO samples was recorded and its behaviour, including the occurrence of phase changes will be analysed.

Jan 1, 2001

By W. J. Birch, R. Farnfield

All shock-tube based initiation systems have a time lag relating to the propagation velocity of the shock-tube itself. This paper examines the exploitation of this inherent time lag to achieve delay blasting with accuracies approaching that achievable with electronic systems albeit over a much shorter delay range. The system employed consists of a combination of standard shock-tube, plain detonators and various shock-tube branching components. The accuracy of the complete system depends on the scatter in delay time induced by each component. In order to quantify this scatter a series of trials were undertaken to determine the variability for each component. These trials are described along with a detail statistical summary of the data recorded.

Jan 1, 2009

By Mark R. Fritzen, Ted A. Fritzen

Anytime that blasting operations will be conducted near existing inhabited structures, vibration damage claims are a major concern of the blasting contractor. It has been our experience that even when vibration and airblast levels generated from a blast are well below accepted damage thresholds, damage claims can still arise. The single greatest source of damage claims is the element of surprise associated with not knowing that blasting operations are being conducted nearby. The second greatest source of damage claims arise from the inability to produce accurate and detailed records of all blasting activity which provides evidence that vibration and air blast levels from each blast had been taken by seismic recording equipment.

Jan 1, 1994

By Florian B. Janoski

The annual consumption of electric blasting caps in the United States approaches 100,000,000, so, over the last eleven to twelve years about one billion have been used. The author has made hazard assessment measurements in connection with proposed electric blasting operations in many places: under a giant, operating electrical generating station, under some of the highest voltage power lines in the country, and around many large electrical distribution substations. Electric blasting was safely conducted in all instances. Measurements of stray current, and of pickup under high voltage power lines are easily made, but it was always a more complex chore to make a good radio frequency hazard assessment "close in" to a high power RF transmitting source.

Jan 1, 1977

By Vaughn Bowns, Allen Stanley, Brian Redeker

"Running casing in drilling operations is often complicated by boulders or large cobbles.Past practices of dealing with these have included use of drop hammers, attempts to drillthrough or around the boulder, contact explosive charges and even pulling the casing andrepositioning the hole. All these methods are time consuming, expensive and offer noguarantee of success. In this paper a different method of dealing with these boulders ispresented that promises to be faster and less expensive with a much higher success rate.This involves using a light plastic conduit pipe to place a shaped explosive against theboulder. It requires no special tools or techniques not commonly in use in the drilling andblasting industry."

Jan 1, 1993

By Rob Farnfield, Mike Kelly, Toby White

There are a variety of sources of dynamic stress which can affect a building and give rise to cracking. A two-storey house, situated in the middle of a surface coal mine was monitored for a period of 30 months to attempt to identify the major causes of cracking. The factors described as environmental include internal and external temperature, humidity, wind speed and direction, rainfall and water table level. These were monitored using a weather station and piezometer and recorded every 20 minutes. The other factors are vibratory and include normal household movement (walking, shutting doors etc.), vehicle vibration and blast vibration. All the significant vibrations in the house were recorded using four sets of velocity transducers and accelerometers.

Jan 1, 1993

By C. Mick Lownds, Dale S. Preece, Ali Bhuiyan

FDM (Fracture Density Model) is a three-dimensional mechanistic model of blast induced rock fragmentation. FDM uses several computational mechanics algorithms to simulate the effect of blasting in different rock types. Earlier, FDM was successfully exercised to simulate 29 small scale shots from the United States Bureau of Mines (USBM), and 6 full-scale bench blasts at the Bararp dimensional stone quarry in Sweden. Excellent agreement was obtained for those shots, and the results were documented in earlier publications. One of the drawbacks of previous ver- sions of FDM was its inability to predict the fines, specifically in Bararp quarry simulations. Ac- curate predictions of fines can be very useful in reducing energy consumptions during down- stream comminution processes and improve the mine-mill operation efficiencies. In this paper, we propose a newer algorithm that can predict the fines as well as the coarse fragments in Bararp with reasonable accuracy. The model was also applied to an open-pit Copper mine with heavily jointed rocks, and it produced very good fragmentation predictions for the full range of fragment sizes. Comparisons with the sieved fragmentation data (for both Bararp stone quarry and the open- pit Copper mines) show great potential for this updated version of FDM in modeling the entire range of fragment size distributions in mining and quarrying applications.

Feb 6, 2023

By Michael Burrell

This project involved the protection of an historic landfill located on the site. Construction blasting was for a permanent access road to carry traffic to and from a new metal processing plant being constructed nearby. The landfill contained materials disposed of during the closure of a Phosphorus plant that had previously occupied a portion of this site.

Jan 1, 2012

By John Floyd, Larry Wardrip

A series of tests were conducted to evaluate the performance of a high density, high velocity cartridged explosive. The tests included two production blasts in a limestone quarry and two production blasts in a granite quarry. To quantify blast and product performance, each blast was monitored with the following equipment: l Two (16mm (Lo Cam) high speed cameras (500 images per second) l Velocity of detonation recorder (I million samples per second) l Four face motion accelerometers (1 million samples per second) l Digital seismograph The fragmentation distribution produced by each blast was quantified with digital image analysis The benefits of the use of high velocity, high density toe loading was quantified in terms of: l Vibration reduction l Fragmentation improvement l Excavator performance In addition to the field tests, a comprehensive evaluation was performed to determine the cost/benefit relationship of the use of the toe load. This paper will include the findings of the study along with guidelines for use in other quarry operations.

Jan 1, 2002

By R. Sibley, K. Perry, E. McCorkle, M. Coy

Black powder has been used in fireworks since the 10 th century in China. To this day, black powder still has a variety of uses, including fireworks, and remains relatively unchanged. Black powder is used in the firework shell to help produce the effect and in the lift charge to propel the shell skyward. The performance of fireworks shells used in displays varies greatly. In fireworks shells, there are two different black powder charges that differ in construction based on the desired performance of the shell. The two charges consist of the lift charge and the break charge. The lift charge is the first to fire and propels the shell out of the mortar. The break charge is the second to fire and is initiated after a delay from the lift charge; its purpose is to burst the shells effect over the desired area of the sky. The lift charge provides the shell with its initial velocity by pressurizing the mortar below the shell body. The pressurization process is violent and occurs in fractions of a second. The purpose of these experiments are to better understand the pressures sustained in fireworks mortars during the firing process. Mortars and shells vary by size and weight. Pressures in each mortar were monitored at various heights along the mortar to provide a pressure profile during shell lift. A high-speed camera was used to measure shell exit velocity near the mortar’s muzzle. This information was correlated with the size and weight of shells and their respective lift charges

Jan 1, 2024

By C. Zuniga, S. Combrinck, C. Peters

Agnico Eagle Gold have partnered with Enaex Australia at their Fosterville gold mine to leverage a combination of drill and blast technologies to optimise underground development mining. The mine is the first site globally to collaboratively develop and trial Enaex SWIFT electronic development detonators, which utilise a novel approach to the user interface, simplifying implementation and enabling the benefits of electronic initiation without the complexity of a conventional system. This has been combined with the use of a Sandvik 422i smart jumbo, and the Enaex underground emulsion charging unit with the capability to tailor the delivery of explosives as required and report on a hole-by-hole basis. The combination of these technologies enables full engineering oversight of the development cycle, in turn enabling optimisation of this process in a historically conservative application. The methodology for leveraging these technologies is to bore a controlled and defined blast pattern through using a smart jumbo, load the blast holes utilising lace loading to deliver a desired quantity of ammonium nitrate emulsion per hole, with the ability to reduce chargeweight for perimeter control, and utilising Enaex SWIFT electronic detonators with flexible template type pre-defined delays to initiate the blast holes. Subsequent to firing and excavation the performance of the blast in fragmentation, advance efficiency, and overbreak and underbreak is measured and reviewed. This is then used to optimise the development cycle and apply to other parts of the mine.

Feb 6, 2023

By Mike Higgins

"The purpose of mining and its related industries is the removal of, and usually the subsequentprocessing of, material from the earth. This includes mining for minerals, quarrying for stone, and civilexcavations. Where this involves rock, the most common method is to fragment the rock by blasting. "

Jan 1, 1997

By James G. Stuart, Tassilo N. Baur

We will discuss the kind of procedure that we use to predict the no-fire (for safety) and all-fire (for reliability) current levels for any given type electric detonator. The basic idea is to expose several detonators to different levels of electric current, so we can estimate the probability of firing as a function of current. We call this a statistical firing test. But what about the uncertainty in measuring the current? Suppose we are not quite sure what stimulus level we apply? This is the question that we will consider here. This relates to both safety and reliability. Surprisingly enough, we will find that some uncertainty in measuring the levels during our statistical firing test improves our long-term safety and reliability

Jan 1, 2019

By R R. Dimock

A goal of all mine operators is to optimize the breakage of the inplace rock to achieve maximum excavating efficiency. The use of the seismograph at Kennecott Copper Corporation's Nevada Mines Division, open pit mine in Ely, Nevada, has demonstrated that optimum blastability can be predicted by knowing the seismic velocity of the inplace rock. The relationship of seismic velocity to the quantity of the explosive required to achieve adequate breakage of the material can be determined. Once quantified, this relationship can be used by the mine operator to obtain the optimum drill pattern and powder factor for breaking the material to be excavated. A substantial savings in primary and secondary drilling and blasting costs can result from using the seismograph for blastability determination.

Jan 1, 1976