Search Documents

By Alexander S. Escalante, Luis R. Ramirez, Nelson A. Arostegui

Research, analyze, discuss, design, and build an electric oven to perform one of the quality control tests the fanel or common fulminers to determine what temperatures they can detonate at. Give practical applications, conclusions, recommendations and bibliography.

Feb 1, 2020

This paper describes the circuit simulations based on SPICE of the SDI Electronic Detonator System at the system level. SDI is launching the Electronic Detonator System with a robust serial protocol exhibiting great ease in field usability and deployment. Programmable delay time with increment of 1 ms up to 10s is possible. Bus length of up to 2 km containing 1600 detonators can be utilized. This system was analyzed using SPICE simulations and an Excel-based firing model spreadsheet. The effects of wire diameter, resistivity, detonator leakage characteristics, blasting array topology (lumped, linearly distributed or branched) were simulated using the firing model. Such spreadsheet is instrumental in determining the blasting topology of any given detonator number and bus wire diameter or resistivity. Initial simulation results were interactively coupled back into making the serial protocol more robust during typical mining conditions.

Jan 1, 2006

By Jonathan Heiner

Rio Tinto Bingham Canyon Mine started its South Wall Push Back (SPB) in 2011. This push back will mine through the only road to the pit bottom (the 10%). The pit bottom is the main ore sector for the mine and supplies about 80 to 90% of the ore. In late 2017 the mine set off a blast in SPB that created a small wedge failure on the high wall between SPB and the 10%. This wedge failure released a rock approximately 20 minutes after that blast that rolled down the wall landing on the 10% near and then contacting a light vehicle

Jan 1, 2019

By Robert Pumpelly

During my nearly 30 years with ATF, (Bureau of Alcohol, Tobacco, Firearms & Explosives), I conducted hundreds of inspections. In many cases hours of time were wasted because the licensee or permittee, who had basically done everything right, was not prepared for the audit. In these cases, required documents were scattered, personnel were unprepared and no plan was in place. This paper will provide some simple steps to avoid these embarrassing delays. A list of common violations is also provided.

Jan 1, 2010

By Evan Smart, Andrew Palangio, David Klingspor, Blessing Taiwo

This study presents a DMAIC-based approach to optimize blasting performance and achieve crusher-compatible fragmentation at the Walker-Severn Quarry in Ontario, Canada. By applying the Six Sigma DMAIC (Define, Measure, Analyze, Improve, Control) framework, the study aims to enhance the integration between blasting and primary crushing operations. Several representative blasts will be simulated and evaluated using both aerial and terrestrial image analysis technologies to assess fragmentation characteristics. The investigation was guided by quarry-specific Key Performance Indicators (KPIs), ensuring that blast design modifications were both practical and operationally relevant. Through structured analysis and data-driven refinement of blast parameters, the study reveals how this framework was used to address the quarry production demand for increased crusher throughput, and reduced processing costs. The existing quarry blast design was assessed as a baseline and compared against the crusher's inlet requirements and the acceptable fines level specified by the quarry. This evaluation aimed to identify and implement modifications to enhance blast performance. A drone (UAV) was employed to capture post-blast images and monitor blast pile displacement. These UAV images were used to generate an orthomosaic image, which was analyzed to assess fragmentation. The orthomosaic was overlaid onto a GIS platform using a 10m-by-10m grid to evaluate fragmentation distribution across the bench and identify areas requiring optimization. Additionally, drone imagery was utilized to monitor the impact of each blast on the subsequent blast's free face and to assess energy utilization for optimizing front-row holes to achieve improved fragmentation. The outcomes of this research offer a replicable methodology for continuous improvement in quarry blasting practices, with a focus on producing fragmentation that aligns with primary crusher requirements.

Jan 26, 2026

According to the Directive 93/15/EEC, given on 5th of April 1993, all the commercial explosives placed on the market and transfered in European Union and EFTA countries have to be certified and contain the CE-marking. Before the products can be awarded by the CE-marking they have to fulfil the Essential Safety Requirements (ESR) of Appendix 1 of the Directive. From the beginning of last year the commercial explosives could not have been be sold in Europian Union countries without the CE-marking. The legitimacy of the Directive 93/15/EEC encompasses High Explosives, Detonating Cords, Safety Fuses, Gun Propellants and Detonators. At the moment in Europe, there are seven Notified Bodies (NB) working in the field of commercial explosives. They are in Spain (LOM), Germany (BAM), France (INERES), England (HSL), Netherlands (TNO-PML), Sweden (SP) and in Finland (PvTT). The Swedish SP has qualifications only for the detonators and the Finnish PvTT for High explosives, Detonating cords, Safety Fuses and Gun Propellants, but not for the detonators. The role of the NB is to work as a third independent body between the client and the manufacturer testing, studying and certifying explosives by the commission of the manufacturer. The Notified Bodies are operating independently competing the clients, the explosives manufactures.

Jan 1, 2004

By R. Narendrula, S. P. Singh

The productivity of a loading machine is affected by several factors. One of the most significant is the characteristic of the muck being loaded. A study was conducted to examine the effects of the looseness, angle of repose, size distribution and moisture content of the blasted material on the efficiency of the loading machine. The study was conducted in the following stages: (a) controlled experiments in the lab, (b) tests with loader simulator and (c) field work in an operating mine. It was found that looseness (%void) in the muck increases with the increase in the value of the mean particle size and index of uniformity of the fragmented rock. Looseness and angle of repose affect the fill factor and the digging cycle time of a loader and in turn the productivity of the equipment. Moisture content affects the angle of repose as well as the stickiness of the material to the loader’s bucket. It was observed that the angle of repose increased with the increase in the mean particle size and the moisture content of the muck. It was also found that the bucket full factor and rate of scooping decrease with the increase in the values of mean particle size and index of uniformity. This was also conformed during fieldwork that bucket fill factor decreases with the increase in the mean particle size as well as the index of uniformity.

Jan 1, 2005

By Kurt Oakes, John Williams

Placer Dome, US operates the Bald Mountain Mine. The Bald Mountain Mine is a surface operation located in remote northwestern White Pine County in east-central Nevada, approximately midway between Elko and Ely. The mine is in the Newark Valley along the southwestern flank of Bald Mountain a part of the Ruby Mountain range, at an approximate elevation of 7,500 ft (2,286 m). The geology at the Bald Mountain Mine is highly altered, both mineralogically, and structurally. Highwall stability and control have long been an issue at the operation, due largely to the varying geologic conditions. In some blasts as many as seven distinct geologic unconformities exist. These unconformities affect both final high wall integrities, as well as blast fragmentation characteristics. A 60 million ton (54.5 million tonnes) layback expansion of the existing “Top Pit” as well as development of a new satellite pit, “Sage Flats”, is being undertaken. Design final highwall pit slopes have been steepened from the traditional 47º to 55º in order to reduce overall ore-to-waste ratios, thereby improving economic viability for the expansion over the 4.5 year life of the project. With the increased usage of electronic detonators throughout the mining industry, mine operations staff, as well as representatives from the mines explosive supplier felt that an evaluation program incorporating electronic detonators would be warranted. The areas of focus for this evaluation would be resultant highwall pre-split integrities, peak particle velocity measurements (both near field and far field), frequency measurements, loader productivity, and visual interpretation of the results. The mine incorporates 25 ft (7.6 m) benches and uses separate trim blasts in conjunction with production blasts in order to reduce blast effects along final highwalls. Hole diameters in production blasts are 7? ” (200 mm). Typical production blast patterns are 18 ft x 18 ft (5.5 m x 5.5 m), drilled in a square pattern configuration. Shot sizes vary greatly, ranging from 200 holes to as many as 800. Bulk low percentage ANFO/emulsion blends are utilized as the redominant blasting agent. Non-electric dual delay detonators (25 ms/500 ms), with non-electric surface delays are the initiation system utilized in production blasts. Typical production blast design

Jan 1, 2004

By A K. Raina, P B. Chourdhury

Flyrock is the unwanted throw of rock fragments to excessive distances in opencast blasting. The incidence is relative in nature incorporating the distance of objects of concern like structures within and outside the mine, equipment within the mine & near the blast and persons within and off the mine. Several attempts to predict and defi ne fl yrock made worldwide could not address the problem since the phenomenon is not a regular feature in blasting. This probabilistic nature of fl yrock allows for risk calculation. CIMFR, India developed a Factor of Safety based risk criterion (10, 14) for evaluation of throw/ fl yrock in opencast mines that incorporates all the above in terms of distance and allowable limit of throw – which in turn determines the risk. The criterion provides the blaster a tool for mathematical evaluation of fl yrock risk in terms of a Factor of Safety and threat ratio (defi ned for the 1st time), thereby enhancing confidence when blasting. The method is easy to use and has been applied to several mines in India and the results are signifi cant. This paper details the evolution of the concept and its application in three limestone mines of India and the results obtained. The application of the method for defi ning a fl exible danger zone is also discussed.

Jan 1, 2008

By Lon Santis

Although unproven, it is suspected that there have been eleven locations since 1988 where explosive generated carbon monoxide (CO) gas moved through the earth and accumulated in nearby underground enclosed spaces. This paper summarizes the incidents, which involved about 30 suspected or medically verified CO poisonings and 1 fatality. Ten incidents occurred in residences and one occurred in a manhole. Although practically nothing is known about the mechanism behind the suspected gas migration, review of the incidents and available information indicates there are certain warning signs and a successful remediation technique available. In each case, overburden heavily confined the explosive in the blasts, preventing release of explosive-generated gases to the atmosphere. All the blasts were in residential areas, and none were excavated immediately. Where the distance from the blast was recorded, 5 of the blasts were within 20 to 50 feet (ft) (6 to 15 meters [m]) of the underground enclosed spaces, 3 were 100 to 150 ft (30 to 46 m) away, and 1 was 400 to 500 ft (120 to 150 m) away. Investigators often identified suspected pathways from the blast site into the underground enclosed spaces. One technique appeared successful at quickly correcting an existing condition. This technique involved applying negative pressure to the earth and removing the CO from the ground surrounding the underground enclosed space.

Jan 1, 2001

By W. Birch

The traditional concept of scaled-distance modelling for predicting blast induced ground vibration holds many drawbacks, not least of which is the major effect data scatter imparts on confidence determination. An investigation by the Department of Mining and Mineral Engineering, The University of Leeds, England has resulted in the development of simple but effective method of improving prediction capacity through the reduction of effective error by incorporating individual location response into a scaled-distance model. The work is the product of an l&month blast-monitoring campaign at a limestone quarry situated in North Yorkshire, England. The data, when presented in the form of a scaled-distance model, indicates a typical scenario where a good overall correlation becomes marred by the extent of data scatter. Examination of the individual monitoring locations however indicates that the response of the individual location is an important factor in the explanation of the large residuals. The novel approach thathas been developed incorporates a series of locational site factors which when incorporated into a scaled distance model reduces the effective error and therefore improves prediction capacity. The approach is based on using a standard computer package “spread sheet” on the understanding that these are commonly available on all quarry or home computers. This approach has been validated by comparison with a more rigorous statistics method.

Jan 1, 2001

By Orica Chile, Orica Brasil, Orica Brasil Victor Morais, Kinross Paracatu Leopoldo Muñoz, Kinross Paracatu Luis Marinho, Gubio Barsottini, Orica Brasil José Vergara, Lucas Steffen, Orica Brasil Washington Vilas

In drill and blast activities, it has been a challenge to sculpt walls accordingly to what has been designed in state-of-art mining design software. Obviously, the perfection of making neat and smooth walls – using aggressive sources of energy, like explosives – are time-and-money consumable and, sometimes, even unnecessary. But undoubtedly, it is vital to guarantee solid walls, safe operations environment, beyond to avoid ore losses and pit constraints caused by poor rock breakage on detonation. Kinross Gold Corporation owns the biggest Brazilian Gold Mine, located in Minas Gerais state. Morro do Ouro mine has reached over 30 years of operation, and due its mature age, the complex has developed its pits, becoming them deeper and surrounded by high walls.

Feb 6, 2023

By Italo Onederra, Miguel Araos

"In order to characterize non-ideal explosives, the explosives industry rely on unconfined velocity ofdetonation tests and where possible underwater pond tests. The information obtained from such tests isquite helpful, however it cannot tell us much about the dynamics of the detonation reaction process. The detonation process has been studied for ideal explosives and the reaction zone length have been measured. However, for non-ideal explosives, that type of information is not available. Therefore, the primary aim of this work was to capture the detonation process of a non-ideal explosive using high speed video camera to determine the zone length."

Jan 1, 2017

By Max Pena Woolcott, Winfried Rosenstock, Maria Chappuis, Walther Hennig

"In a Peruvian-German Technical Cooperation project for the Mining Sector the ""Milpo-cut"" along with the electric initiation system has been successfully implemented in a Peruvian metal-ore mine.Specific savings in drill work and explosives consumption up to 50 % have been achieved in headings and slopes. The positive results have motivated further Peruvian mining companies to introduce the new technique."

Jan 1, 1994

By Martin Langenderfer, Sergii Chertopalov, Catherine Johnson, Vadym Mochalin, William Fahrenholtz

The high temperature and high pressure of an explosive detonation can be used for the production of nanomaterials. The controlled detonation of explosive compositions along with the collection and characterization of reaction products encompasses a process known as detonation synthesis. The primary advantage of the method of detonation synthesis is the possibility for producing monocrystalline nanoparticles with diameters of less than 10 nm. In order to successfully synthesize nanomaterials via the detonation process, it is necessary that the explosive detonation is conducted in a sealed environment. This environment when pulled to a vacuum or purged with inert gas such as argon will reduce the oxidation of detonation reaction products. Detonation synthesis testing is currently being conducted in a 1.8 cubic meters (m3) (64.3 cubic feet (ft3)) ellipsoidal pressure vessel consisting of two interlocking half shells. The testing involves the controlled detonation of cast mixtures of Cyclotrimethylene-trinitramine (RDX) and 2,4,6-Trinitrotoluene (TNT) in conjunction with siliceous compounds to produce nanocrystalline diamond and silicon carbide. Alternative detonation environments including the presence of a cooling medium such as water or dry ice to absorb residual, post detonation, thermal energy and enhance the stability of the materials being produced have improved yield. Modifications to the explosive charge composition have an effect on the type and quantity of materials that can be produced. Doping of explosive charges with various organic and inorganic compounds has shown promise in the synthesis of materials that are difficult or uneconomical to produce through other methods. This paper outlines the process development of detonation synthesis facilities. Preparation of the pressure vessel to create a suitable detonation environment for the production of nanomaterials is examined. Formulation of explosive charge compositions and considerations involving test charge initiation are discussed in detail. Experimental results and analysis from initial testing as well as plans for future research are also evaluated.

Jan 1, 2018

By Peter Moser

The average annual consumption of raw minerals in Europe is 10 ton per person. About 50 % is produced by blasting. For a population of 450 million (including the population from the countries of the new member states) this makes 2.25 billion tons of blasted rock, 80 % being building industry aggregates and industrial minerals. In aggregate quarries 10-15 % of the rock blasted can’t be sold, as the material is too fine, i.e. smaller than 4 mm. This ‘fines problem’ is worse in the quarries of limestone and cement producers where up to 30 % of the material is useless. Thus about 450 million tons of useless rock fines are produced and put on waste dumps every year, i.e. 1 ton/person. This problem is addressed by the research project LESS FINES - “Less Fines production in aggregate and industrial minerals industry” which is funded by the European Union under the project contract G1RD-CT-2000-00438. The project consortium, formed of nine partners from 5 EU countries, works on the following two main research subjects: 1. The determination of the natural breakage behavior (NBC) of the rock mass, which is defined as the particle size distribution curve for a certain rock mass with the maximum uniformity and thus for a given maximum particle size that fragmentation curve which gives the minimum amount of unusable fine material. The comparison between the NBC and an actual blast fragmentation curve allows to quantify the fines reduction potential. 2. The adaptation of explosives properties, charging techniques and timing in order to produce only the minimum, inherently unavoidable percentage of fines. With about 15 full time working persons the project is estimated to be one of the largest blast related research activities in Europe at the time of the project period. The project is coordinated by the Department of Mining Engineering& Mineral Economics of the University of Leoben.

Jan 1, 2004

By A. W. (Sandy) Neilson

Whether you are a general contractor who hires subcontractors to perform blasting work or you have your own blasting crew, it is extremely important to understand how Business Liability Insurance works, regardless of who is ultimately providing the coverage. If close attention is not paid to the limitations and preblast survey requirements under most policies that provide blasting coverage, you could find yourself facing an uninsured loss.

Jan 1, 2002

By Joe Strobbe, Kevin Joe

The U.S. Bureau of Reclamation awarded PCL Civil Constructors the project to build a new visitor's center and parking lot structure at the Hoover Dam. The excavations for these structures present many blast design challenges. The visitor center, a 30 foot deep excavation was blasted in the Nevada side of the canyon wall, 600 feet above the existing power plant. This excavation also included a through-cut underneath the existing road that carries the traffic over the Dam between Nevada and Arizona.

Jan 1, 1993

By Daniel Vargas Quispe, Yorhinio León Robles, Marco Jauregui Vargas, Helen Espinoza Bailon, Oshin Quispe Luya

This project describes the methodology applied during the execution of tests to determine the multiple controls that mitigate damage to the final walls of the pit. The different tests were executed on production pattern, which considered: modification of the angle of pre-split drill line, damage evaluation in individual drills with different load designs, varied detonation sequences, capture and analysis of elementary waves. After the evaluation and analysis of the results obtained in the tests, we are in process to standardize various damage controls such as; the combination of pre-split drill line angles at 80° and 90°; charge design in buffer drills that reduce the angle of action of the explosive and a detonation sequence that involves the creation of a relief filter that is made up of the detonation of two rows next to the pre-split drill line, which will have the function of filtering the waves of vibrations produced by the detonation of the production drills and at the same time it modifies the direction of damage towards the blasted material. The analysis of the different controls, as well as their combination, will allow us to improve the compliance results of the formation of benches.

Jan 21, 2025

By Peter Duniam, Vivian Patz

History of the ExEx 1000 CAB system. l What we’ve learned using electronic timing. l Requirements for a second generation. EDD system. l The ExEx 2000 system - simple, versatile and cost effective

Jan 1, 1997