Search Documents

By Doug Wathen, Philip M. E Thomas

The City of Fort Myers needed to replace a 40-year old 42-inch storm sewer line in downtown Fort Myers with a new 54-inch line to accommodate population growth. The old line had to be kept operational while a new line was installed. the contractor spent two months using a drop ball, a hoe ram, and large rippers trying to break the three to four feet of rock that needed to be removed to accommodate the new pipe. Mechanical trenching was considered but was proven to be overly expensive. On very short notice, Ireco of Florida was asked to design and execute a blasting procedure that would allow this project to proceed. Nearby buildings were over 80 years old, three of them containing antique shops specializing in glass antiquities with attorney offices above them. High water table compounded problems with a 20-year old steel water main and clay drainage pipe 15 feet from the new sewer line. Holes had to be drilled within six inches of the edge of the existing pipe to four feet below the pipe on either side of the pipe and blasted. No interruption in the sewer line flow was to be tolerated.

Jan 1, 1996

By W. Jiao, Y. Yongqi, R. Shan

Soft rock mines are distributed through out P.R.C. And drilling and blasting is still the main method of driving a tunnel in these mines. Traditional smooth blasting has been widely and deeply studied and put into practice in P.C.R since 1970s. But the cartridge and blast hole are both columns, the stress field in the rock around blast hole at the beginning is symmetry around hole axis, and the original cracks in the rock can be activated randomly. So serious overbreak and underbreak at the boundary of an excavation occur often, especially when the excavation is in soft rockmass, and the rates of half-hole marks are generally about 50% in medium rock, and 20-30% in soft rock in Chinese coal mines. For the sake of overcoming the situation, we have been studying directed crack blasting since ten years, and have got some obvious achievements in this respect. Slotted cartridge control blasting in soft rock is studied in this paper. Through model experiments, reasonable decouple coefficient range and slot width are gotten, and unsymmetrical dynamic strain field is analyzed. Through underground test in soft rock with a strength lower than 1OMpa in Dayan Mining Bureau, The results of which the rates of half-hole marks and the nonsmooth grades of the cut contours are 83.3% and 1OOmm respectively have been achieved.

Jan 1, 2000

By J T. Keim

Members and guests of the Society of Explosive Engineers, it's indeed a pleasure for a longtime practical user such as myself to have the ears of so many explosive experts for a few minutes just to express my feelings and concerns on blasting as well as the feelings and concerns of many other users and operators.

Jan 1, 1978

By Leslie Taylor, W. Fourney, Uli Leiste

This paper presents the results from a series of tests conducted to investigate the total vertical impulse delivered to a target plate by a buried explosive charge. The tests were conducted at a very small scale but previous work has shown that small scale testing can predict impulse applied to plates in full scale. Non-deforming plates were used to determine the change in impulse delivered to targets as a result of changes in standoff distance and burial depth changes.

Jan 1, 2009

By D. Bartley, R. McClure, W. Reisz

Ever since the 8ms criterion was developed in the early 60’s there has been an ongoing debate among many blasters as to its actual value in controlling ground vibration. The perpetuation of the myth surrounding the 8ms window can be partly attributed to its simplicity and convenience as a means for regulatory compliance. Unfortunately, the mindset that many blasters have adopted has hindered the development and use of more effective techniques and in many cases can actually be counter productive to vibration control.

Jan 1, 2006

By James G. Stuart

For precise control and timing of a blast, people use electric detonators. Most of these contain a fine metal “bridgewire,” that heats to the required burning temperature when electric current passes through it. Users should be careful. Stray voltage can fire these detonators. Some designs are particularly susceptible to electrostatic-discharge (ESD). We will discuss some of the accidents we have encountered in our forensic work. We will recommend specific safe procedures for handling and firing these devices.

Jan 1, 2005

By P Cotton, N Cox

The Brisbane City Council has implemented a program of continual improvement at its Mount Coot-tha Quarry in the heart of Brisbane, Australia. The program has been underway for the past 6 years, and has resulted in very significant improvements in terms of both the cost effectiveness of its operation, and in terms of its environmental impact on nearby residents. The work has included a focus, amongst other things, on blasting efficiency, and has challenged conventional thinking in terms of the size of blasts fired, the frequency of firing, the diameter of blastholes, and the use of bulk emulsion or slurry explosives.

Jan 1, 1995

By Paul N. Worsey

Disturbed zones of rock have been measured for blasted highway rock cuttings by Matheson and Swindells of the Transport and Road Research Laboratory (TRRL) of Great Britain. These zones have been shown to be directly attributable to the blasting process and accordingly vary in depth depending on blasting technique. Perimeter blasting such as smoothwalling and pre-splitting has been shown to be effective in reducing the depth of disturbed rock. Although extensive work has been carried out on surface excavations for medium diameter (l00mm) blast holes, none has been undertaken for underground excavations.

Jan 1, 1985

By John M. Bolger, Keith E. McMaster

Excessive salt fines are undesirable in underground salt mining as they are considered a costly waste byproduct. This paper describes an extensive explosive application program conducted at The Canadian Salt Company Ltd, located in Pugwash, Nova Scotia, Canada. The prime objective of the program was to reduce the quantity of fines generated from this company’s underground production blasts. The program was known as the “The Fines Reduction Program”.

Jan 1, 1996

By J J. F Smith

The application of pneumatically loaded ANFO for underground mining has continued to increase year by year since the technique was first developed and introduced underground during the early 1960's. Improvements in the manufacturing process for explosives grade prills, the design and construction of more efficient AN prill-fuel oil blending equipment, and the introduction of more durable and reliable pneumatic loaders have promoted the wide application of the relatively low cost blasting agent, ANFO.

Jan 1, 1982

By P Albert

A wedge-shaped underwater rock plug has to be blasted in order to tap the reservoir and furnish water to a new underground powerhouse at Manicouagan-5. The paper deals with the design and engineering aspects of drilling and blasting of this plug where the topographical configuration is extremely difficult. In this study small diameter vertical holes are considered with the OD-method and a fixed platform is recommended for drilling and loading operations.

Jan 1, 1984

By R W. Givens

This paper presents blast casting design variables that have been developed and are currently being used at the High Power Energy mine in West Virginia. The shot specifications are summarized in Table I. The two active casting pits were designed with casting in mind and as a result are better designed and more efficient. About 55% of the overburden material is effectively cast and clean up is done by a bulldozer, front-end-loader, and trucks. This results in a 15X decrease in the cost of coal production.

Jan 1, 1988

By Thomas F. Mechtenberg, Michael S. Powell

In the past several years many coal operators and stone producers have reduced drilling and blasting cost by utilizing Bulk Emulsion/ANFO blends. For many operators the cost of equipment to handle blend products has been a major consideration in evaluating overall cost effectiveness of changing from packaged products or bulk ANFO to blends. This is especially true when the project length is short term or is uncertain.

Jan 1, 1990

By R Holmberg, C Sjoberg, B Larsson

This paper describes the excavation of an underground naphta storage facility at Stenungsund in Sweden. The main purpose with this paper is to give an overall view of how the excavation was carried out and in what type of bedrock the storage was built. Emphasis has been done to highlight the importance of using cautious blasting to avoid blast damage in the remaining rock. Attempts has also been done in order to evaluate what the degree of Swedish cautious blasting has meant for the rock support costs during the construction period.

Jan 1, 1984

By Isaac E. "Chip" Harris

Any contractor who agrees to supply materials or to perform services for a sum, is well aware of the importance of proper pre-bid information. Being able to properly plan costs and methods results in profits that allow the contractor to prosper. The paper discusses procedures used in estimating pre-bid cost; in particular, drilling and blasting cost for highways, dams and general construction projects. It breaks cost down into five categories and relates them to a total estimate used in bidding and budgeting a construction project.

Jan 1, 1975

By Lon D. Santis

The Code of Federal Regulations Title 30, Parts 56, 57, 75, and 77 require that detonators and explosives be separated by four inches of hardwood or equivalents when transported together in mines. This standard was developed to protect the explosives from initiation by the more sensitive detonators. The research reported here is an attempt to quantify the fire protection offered by four inches of red oak and other materials. Boxes with a volume of 6.75 cubic feet were made from four-inch thick rough green oak (RGO), two-inch thick RGO plied, two-inch thick #1 common (dried) red oak plied, and a metal/plywood composite. These and boxes meeting the Institute of Makers of Explosives' (IME) Safety Library Publication No. 22 were tested in bonfires. The boxes were instrumented with thermocouples, filled with detonators, and placed over a kerosene fire imparting about 16 kilowatts per square meter heat flux for up to 3 hours.

Jan 1, 1997

Fracture Control Blasting is an alternative to pre- and post-splitting or smooth wall blasting. It was developed at the University of Maryland as an attempt to overcome some of the disadvantages that occur with normal blasting practices. There are two main factors that are unique to fracture control blasting. First, it utilizes a notched or grooved borehole to initiate fractures at desired locations and secondly, it employs a very carefully selected charge so as to provide control over borehole pressure. The maximum borehole pressure must be kept between very definite limits in order to obtain initiation of fractures at locations where they are desired and yet not obtain fractures where they are not desired. When coupled with stem induced fracturing, which was developed for oil and gas well stimulation, it has been found that the charge required for fracture control can be as little as 1/40th that required for normal smooth wall blasting. The paper describes the technique of fracture control blasting and gives results of some of the field testing conducted to date.

Jan 1, 1984

By Dieter Froelich, Giles Turcotte

In the near future, Bong Mining Company (BMC) will start mining a new deposit known as Zaweah II which is a narrow iron orebody requiring multiple row blasts with the bench floor as a free face. This called for the development of a new blasting technique. The article delineates the problem and its restrictions related to blasting. It also describes the approach which was taken for developing this new blasting technique which is essentially an application of the cratering theory with near spherical charges. Basic crater tests were conducted using various combinations of hole sizes, explosive strengths and delay patterns. From the results obtained, several alternatives were considered for production blasts and the most promising ones were evaluated.

Jan 1, 1980

By M. L. Mendes, J. Q. Nojiri, S. C. Botelho, A. P. Campanha

In February 28, 2001 JOULE coordinated the first tests with an electronic detonator in South America at an iron ore operation - ITABIRA MINES from the Brazilian COMPANHIA VALE DO RIO DOCE (CVRD) - the largest producer and exporter of iron ore in the world. ITABIRA MINES (CAU and CONCEI O) belong to one of the complexes, called the Southern System, producing 56 million tons of ROM as well as concentrated products and pellets. This paper is going to describe the tests at ITABIRA MINES with results indicating the improvement in the excavator productivity and reduction of the mining global costs (due to the better performance of the equipment and potential reduction of the maintenance cost).

Jan 1, 2002

By Split Engineering Chile Fernando Fernandez

Mathematical modeling in conjunction with mineral characterization is widely used as a method for design and optimization of comminution circuits, to simulate the processes of crushing, grinding and classification. An important input parameter to the simulation models is the Run-of-Mine Particle Size Distribution (ROM PSD). The run-of-mine size distributions due to blasting have a great influence on the performance of a semi-autogenous grinding (SAG) mill. In this paper, a mine case study was conducted where there are four primary geologic units and the material properties between the four units vary considerably. Also, the mixture of the four unit that will be mined at any given time also vary considerably. This presents a challenge in terms of optimizing the blasting for mill production throughout the mine life. As part of the case study, field rock mass characterization, laboratory rock mechanics tests, and laboratory breakage tests were conducted. The field characterization and rock mechanics tests provide material properties used to simulate the effect of different blast designs on run of mine particle size distributions (ROM PSD). The JKSimBlast software was used for these simulations. The rock breakage tests provide material properties used to simulate crushing and grinding performance. The JKSimMet software was used for these simulations.

Jan 1, 2015