Search Documents

By Alastair Grogan

In October of 2002, the author was retained by Public Works and Government Services Canada, on behalf of the Department of National Defense, to design, construct and test the effectiveness of a bubble curtain system at an underwater demolition range, near Victoria, BC. The purpose of the bubble curtain was to reduce the potential for fish mortalities at the site. This paper presents some of the elements of the design, along with the results of overpressure monitoring during blasting and compares the results of fish mortality and animal behaviors with and without the bubble curtain in operation.

Jan 1, 2005

By John Capers

•The IME is the Safety and Security Association of the commercial explosives industry in the United States and Canada. •Founded in 1913 •Board of Governors •5 Standing committees- 1. Technical 2. Environmental Affairs 3. Legal Affairs 4. Safety & Health 5. Transportation & Distribution

Jan 1, 2006

By David Flores, Benjamin Cebrian

Gold mining require high levels of dilution control due the high value of ore. These types of operations employ short benches, which are suitable for ore control, lower displacement and more representative block models. However, shorter benches makes fragmentation by blasting difficult because blast designs tend to be stiff in regards to burden/bench height ratio. This is especially relevant in hard, massive ore bodies where usual drilling diameters lead to poor energy distribution. In regards to control ore loss and dilution, there are different techniques to minimize both, which include: panel blasting, buffer blasting to muck piles and differential loading of areas of the blast bench. All of them should be sequenced with appropriate displacement along the ore/waste contacts. This paper describes extensive engineering approaches to achieve both dilution control while not hurting fragmentation in the very hard, massive ore sections of a mine case study. Ore Tracker microchips are used to correlate performance of these designs at the SAG mill (bottleneck of this specific operation). Another gold mine uses the same technology to detect when and where operational dilution is happening. The system tells where flagging of the different ore bodies has been followed in order to detect which operators pass the excavation limits beyond ore control flagging.

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine. Montana Technological University (Montana Tech) obtained a time-domain reflectometer (TDR) type VOD monitoring unit. Purchase of the VOD monitor was justified on verifying explosives performance used in Montana Tech’s practical underground mining class and provide a teaching aid for the school’s rock fragmentation class. Before demonstrating the unit to students, we figured we better learn how to use it first so we give the students an appropriate experience. Our first learning was in obtaining the correct coaxial cable for the VOD monitor and how to properly terminate the cable. Once the cable was on-site and terminated, VOD testing could commence. Use of the VOD monitor was tested underground in small diameter holes (1.5-inch, 38 millimeter) pneumatically loaded with ANFO. After a few failed trials, and follow-up discussions with the supplier, VOD readings were obtained for the ANFO loaded holes. Additional readings were obtained for a pre-split product and detonating cord to satisfy our curiosity that the unit was performing as specified by the manufacturer. This paper will share our learnings in the hopes that others can benefit.

By T Goswami

The conventional practice in open cut coal strip mining has been to blast the overburden or coal layers in separate blast events. This is done in order to maximise the benefits from throw blasting and also to limit coal losses. Each blast event usually has a particular design of hole diameters, burdens and spacings, explosive charges and blast timing in order to achieve the required blast outcome for either the overburden or coal. This means that each blast has to be separately cleaned on the surface after excavation of the previous blast. Hole locations then have to be individually surveyed and marked, holes drilled, explosives and initiators loaded and the blast fired. Each of these actions takes considerable time and resources and therefore impacts on mine productivity. The mine has to be cleared for each blast event and every blast presents a new potential source for noise, dust or vibration disturbance to the neighbouring population. Exposed highwalls are also subjected to vibration and damage from each subsequent blast event

Jan 1, 2006

By Thierry Bernard

This case study shows how a unique combination of field measurements and advanced technologies allowed blasters designing, loading and firing an incredibly challenging quarry blast.

Jan 1, 2015

By Robert Hopler

This article, advocating having employees whose specific job would be to fire blasts in underground coal mines in llinois, was written 5 years prior to the establishment of the U.S. Bureau of Mines, and 2 1/2 years before the worst month in U.S. coal mining history, when 692 miners were killed in three separate explosions in December 1907. Obviously something had to be done to improve safety in the use of explosives, and having dedicated shotfirers was a good first step.

Jan 1, 2006

By Michael Wieland

The resolving capacity of the thermodynamic work-principal model has been seriously refined over its twelve year history, so a review of the innovations, wrong turns and their rectification is warranted to help future researchers. The work-principal model rests upon the four laws of thermodynamics that drive the universe and relatively few other assumptions: like the removing and imposing of constraints on the quasi-potential to yield trapped minimum key-states that represent the wanted process. The formative research was concerned with the role of ingredient changes, the removal of booster influence and the quench temperature with which to reckon toxic fumes. The transfer of reaction-zone energy as work upon the surrounding rock/water/fixture was not fully rationalized until the notion of reversed-inertial pressure was formulated and determined (for water) with underwater trinitrotoluene (TNT) shots. The rock-water-jelly model incorporated that term into its dynamic pressure formula as a way to represent rock blasts or underwater shots, while the zone of reaction gases remained trapped. The real irreversible thermodynamic process, which yielded the total expansion work, was later complemented with a wholly reversible imaginary process, to form a closed thermodynamic loop, with a remarkable consequence – the determination of the theoretical heave and hence, the undissipated-shock by difference from the total work. With the wholly developed model, it was recently possible to quantify the time retardation of reaction chemistry for non-molecular (mining) explosives, as compared to the rather negligible time-retardation found for the molecular (military) explosives in underwater tests.

Jan 1, 2009

By Tom Treleaven

The widening of the Panama Canal to approximately 130 feet (40 m) for its entire length began just a few years ago. The original expansion program was slated for completion in 18 to 20 years, but has recently been reduced for completion within the next four years. This means that a tremendous amount of blasting at simultaneous points along the canal, by both the Panama Canal Commission (PCC) and many subcontractors, is necessary to achieve the new completion deadline. The accelerated program also imposed many logistical concerns, since marine trafIic is always heavy and cannot be stopped for blasting. Because some of the large and heavy cargo vessels clear the bottom of the canal by only about 6 feet ( 2 m), the blasting cannot result in any large boulders into the center of the canal, for fear of grounding and damaging a vessel, not to mention the traffic delays and lost income of approximately 1 to 2 million dollars per day.

Jan 1, 1997

By C Agreda

The Cushion Blasting Technique applied to solve the high risk case history represented by a 10,704 TM rock locate at 120 M from the hydroelectrical plants of 350 KV each, is described, analyzed and discussed. The generation and distribution of 700 KV produced by two hydroelectrical plants must not be interrupted by any reason, because the 26 district of the province of cajatambo, of the Lima department; would not have electrical power. The search of the best alternative and methodology, the drilling and blasting pattern calculations, charge design and loading, connections and initiations of the 50 blasts are described, analyzed and discussed. Finally, the excellent results from a technical, economical, enviromental and safety point of view of the 50 primary blasts are discussed and emphasized.

Jan 1, 2005

By Harry Verakis, Thomas Lobb

In the past decade, approximately 5 billion pounds of explosives were used annually in the United States. Most of this quantity of explosives was used by the mining industry and coal mining was the dominant application for explosives. Considering the large amount of explosives used, the accident safety record for the mining industry has improved significantly over the past two decades. Blasting accidents are usually a small percentage of the total number of mining accidents. However, blasting accidents continue to occur and the severity of these accidents is disproportionately high with respect to other types of mining accidents. This paper is a summary and an update of the surface mine blasting accident investigations and studies conducted previously by the Mine Safety and Health Administration (MSHA) and the former U.S. Bureau of Mines.

Jan 1, 2001

By Tom Goodell, James Cox, Scott Scovira

Resolution Copper Mining is sinking a 6943 foot (2116 m) deep shaft to access and develop a new panel caving mine with approximately 1.6 billion known tons of porphyry copper resource. This mine will take several years to ramp up to its full production level of 132,300 tons per day (120,000 tonnes per day) and is scheduled to begin production in the early 2020s. Resolution's shaft sinking contractor Cementation USA is using state of the art sinking methods combined with a largely local labor force to complete this record breaking shaft. Resolution's No. 10 Shaft has finished diameter of 28 feet (8.5m) and as of October 2013 is at the 6625 foot (2020 m) level. Upon completion in early 2014, the No. 10 Shaft will be the deepest single lift shaft in the United States.

Jan 1, 2014

By Randall S. Marks

Bonneville Dam, completed in 1938, included the smallest and busiest lock on the Columbia and Snake River Navigation System. To expedite barge traffic through this restriction, a new larger lock was designed and contracted by the U.S. Army Corp of Engineers.

Jan 1, 1997

By Dale S. Preece, J Paul Tidman, Stephen H. Chung

"A discrete element computer program named DMC-BLAST (Distinct Motion code) has been under. development since 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employsexplicit time integration and uses spherical or cylindrical elements that are represented as circles in2-D. DMC-BLAST calculations compare favorably with data from actual bench blasts (Preece et al,1993)."

Jan 1, 1997

By Sanna Mustonen, Seppo Mellanen, Mellanen, Pekka Kantia

In Finland Posiva Oy (Company) is responsible for implementing the final disposal programme for spent nuclear fuel of its owners. Company is preparing for the geological disposal in Olkiluoto crystalline bedrock. Excavation will be executed using drill and blast method. Method unavoidably causes variable excavation damaged zone (EDZ) on tunnel surfaces. The EDZ constitutes a risk for long term safety and therefore good control methodology of the blasting technique is required. The thicker the EDZ, the greater is the likelihood for detrimental transport pathways for ground water to transport radio nuclides, should those be present.

Jan 1, 2016

By Josee Boudreau

Transport Canada has regulatory requirements that pertain to the transportation of explosives. An important component includes the requirement for an approved Emergency Response Assistance Plan (ERAP). The ERAP may be traced to the recommendations made by Justice Grange following the enquiry into the Mississauga train derailment of December 1979. Justice Grange recommended that any shipper of dangerous goods must have a plan to control any release of dangerous goods in the event of an accident, and that the plan must be submitted to the Minister and approved by the Minister or by an organisation or person designated by the Minister. The right to ship could be withdrawn at any time if the plan is found inadequate either in its conception or in its operation.

Jan 1, 2010

By Troy Williams, Chris Preston, Ian Lipchak

"Underground blasting operations are challenging from the standpoint of the distribution of explosivesenergy representative of ring blasting. Energy from both shock and pressure regimes of commercialexplosives may appear concentrated in the collar region of a typical ring blast and diluted at the toes of holes due to the oblique geometries of blastholes. The non-homogenous nature of ore in whichexplosives are distributed via drillholes, adds to the complexities of generating particulate profiles from fragmented material with consistencies that are predictable from blast pattern to blast pattern - well suited for specific underground handling equipment and mill processing. In an ideal world, it would be the blasting operations themselves that represent the primary crushing mechanism, or at least mitigate mechanical crushing that can comprise a large component of the cost in generating suitable muck. This paper presents a dynamic break view in 3D that allows a planner to visualize the potential break zone around a blasthole generated by an explosive load using a Kleine field. Simple as it sounds, this methodology provides information that can be used in conjunction with cavity monitoring surveys (CMS) to potentially judge dilution due to overbreak as well as recovery for a typical blast. As examples, there are two break geometries that are examined regarding circular breaks and elliptical breaks around blastholes. Using a Kleine field to define break, a planner generated isosurface can be generated and compared to CMS data for calibration and prediction, using AEGIS 3D ring design software."

Jan 1, 2016

By Alan: Moore Richards

Effective control of airblast requires that significant factors be identified and satisfied by blast design and careful implementation. Significant factors include charge mass, distance, face height and orientation, burden, spacing, and initiation sequence, stemming height and type, topographical shielding, and meteorological conditions. This paper utilizes case histories of blasting in Australian open pit mines to demonstrate techniques that have been used to control airblast to applicable limits.

Jan 1, 2006

By Tjaar A. Louw, Albert P. Van Niekerk, Johannes J. Louw, Attie J. Goosen

Unlike molecular high explosives, commercial explosives based on ammonium nitrate do not detonate ideally according to the theoretical model for steady state, one-dimensional detonation. One of the reasons for this deviation from ideal detonation is the slower chemical reaction, due to less intimate contact between the oxidiser and fuel components. It is well known that the inclusion of gas pockets, such as microballoons, in the formulation of ammonium nitrate based emulsions and watergels enhances the performance of these explosives. Various different interpretations of the “hot spot” theory have been proposed to explain this phenomenon.

Jan 1, 1997

By Mike Cammack, Logan Huppert, Gustavo Azpilcueta

During the summer of 2015, Unisea Inc. sought proposals for the G1 Dock Replacement Project in Dutch Harbor, Alaska. It would be a one year project and construction was scheduled to begin in the spring of 2016. One aspect of the project was the requirement for a layer of armor stone to protect part of the dock. An estimated 30,500 tonnes (37,670 t) of armor stone were needed for the project. The source of rock was the Unisea Quarry due to its proximity to the project and the quality of the stone meeting all the required technical standards.

Jan 1, 2018