Search Documents

By Pat McLaughlin, J R. (Dick) Daniels

Current practice in establishing quarries in remote areas with hilly or mountainous terrain tends to the use of airtracs (or similar pioneering units) drilling horizontal holes to establish a face, followed by bench development with light excavating equipment. The authors propose the use of a hybrid coyote blast design that incorporates long-round tunneling techniques. This method would, in effect, use down-the-hole (DTH) drills to advance the drift cut to the final depth, allowing longer and more rapid drift advances, and replace the cross-cut drifts with clusters of DTH holes to achieve the same explosives distribution.

Jan 1, 1995

By Tom Burleson

High-speed photography has proven to be an extremely valuable tool for the evaluation of blasting practices in the Warrior Coal Basin. A research project, coordinated by Nelson Brothers Inc. and The University of Alabama's Mineral Engineering Department, has centered on the use of high-speed photography to study and analyze blast performance. A large number of production shots in this region has been filmed and studied. The data obtained from the films have been used to establish graphical relationships between certain blast parameters and overall shot performance. These relationships will be used to develop a computer model that will estimate cast results from a given burden explosive energy combination. This paper describes the methods and procedures used to develop these relationships. The results of the research are discussed along with plans for continuing the research project.

Jan 1, 1988

By Vilem Petr

Optimization blast design parameters for rounds used at surface mines, quarries or cast blast has taken on a new importance with the increased the cost of the explosives and electronic detonators. This paper addresses the fundamentals of blast design and optimization explosive energy utilized for fragmentation. This laboratory studies shows that one key variable-the strain energy set up in rock mass by blast vibration – can be used to predict the extent of damage done to the rock strata, the degree of fragmentation of the broken rock, and the velocity of the broken rock. It also shows how the dynamic strength of the rock strata is influence the fragmentation size distribution as well as the blastability.

Jan 1, 2008

By J T. Patterson

The mining, quarrying and construction industries are often blamed for causing damage to residential-type structures when explosives are used. The claim experience for blasting vibration damage has been poor. This coverage is excluded from the Comprehensive General Liability (CGL) policy. To obtain this coverage, the policyholder must meet additional criteria and an additional premium must be paid. The risk management process offers the explosives user a technique for minimizing the risk of complaints and vibration damage claims on his insurance program and his cash flow. Case histories indicate that the vibration damage claims expense may be a lower risk than the risk of interference with production and cash flow. An annotated bibliography on risk management and defense of vibration damage claims is provided.

Jan 1, 1978

By Jerry W. Schweiker

An extensive computer program has been developed which will store and analyze pertinent blast related parameters such as date, time, shot coordinates, charge, delay times, etc. In conjunction with these blast parameters, measured ground vibration information can be stored. In addition to actual seismograph data, predicted ground vibration in terms of velocity (inches/sec) can be generated for selected receiver locations. The magnitude of the blast generated ground vibration is based on scale distance relationships. The program can be used for planning blasts, to satisfy local environmental regulations and for insurance and/or legal purposes.

Jan 1, 1984

By N Vijay Mohan, K V. Balamukund, G Ananth Ramulu

Jointing of steel rods in reinforced concrete structures needs careful consideration as it renders the structure weak at the joint. The jointing is usually done at sections of structural members, where the bending moment and shear force are least. Jointing is done either by overlapping the rods or welding or by mechanical splicing. A novel method of jointing them is by inserting the two rods in a steel sleeve and cladding it on to the rods by subjecting the sleeve to explosive energy. A rod jointed in this fashion is tested for direct tension and bending when used in a reinforced concrete beam. The test results show that it is an effective method. The advantage is that a number of joints can be made in a single operation.

Jan 1, 1993

By Dale S. Preece

A discrete element computer program, DMC (Distinct Motion Code), has been used for several years to simulate blasting-induced rock motion. Recent enhancements of DMC's capabilities have included addition of an algorithm that couples together rock motion and gas flow. This allows the user to specify a particular explosive which also specifies equation-of-state and other parameters necessary to model explosive gas flow from the blastwell. Rock loading by the flowing gas is calculated automatically. The mechanism for calculating the rock loading is the subject of this paper. The rock motion effects the gas flow calculation by changing the porosity. DMC is currently being used on a SUN SPARCstation 2 computer workstation.

Jan 1, 1993

By Richard J. Mainiero, Michael S. Wieland, Harry C. Verakis

The Bureau of Mines, U.S. Department of the Interior, has been conducting research on delay blasting in underground coal mines in support of the efforts of Mine Safety and Health Administration (MSHA), U.S. Department of Labor, to revise coal mine blasting regulations. Part of the research centered on developing an understanding of the factors that lead to misfires of permissible explosives. Research was conducted to determine whether frequency of misfires was related to borehole spacing. For a wide variety of permissible explosives, misfires were observed for about 50 X of the holes at 45-cm (18-in) spacing. Misfires were also observed for 60-cm (24-in) spacing, but the frequency of misfires was much lower than observed for the 45-cm (18-in) spacing. The Bureau has recommended that hole spacings of less than 60 cm (24 in) be prohibited.

Jan 1, 1986

By Sanjay Sengar, Nabiullah Pingua, Saurabh Sahay

In India, more than 80 percent of the total of 557 million metric ton coal production comes from open-cast mines involving large overburden removal with average 1:3.5 stripping ratio which is going to in-crease in future. This operation consumes nearly 0.5 million metric ton explosives consisting of 80-85 percent bulk explosives and remaining 15 to 20 percent non-permitted large diameter explosives. Quali-ties of bulk explosives play an important role in rock blasting. Post blast results like poor fragmentation, tight mucking, toe problems, improper muck profile and lower productivity of mine may require chang-es in explosive loading factor (amount of explosive used per unit of rock blasted ). The explosive load-ing factor is an extremely important index to assess the economy of blasting operation.

Jan 1, 2014

By Tapan Goswami, Michael Croucher

At Bayswater Colliery various methods of controlling highwall stabii were investigated. The use of presplitting was trialled and its effectiveness measured. The presplit hole spacing and explosive charge were based on those succes& lly used in other coal mines in the Hunter Valley. The major presplit design parameter to be determined was the stand-off distance between the presplit line and the back row of the production blast. This could not be transfmed directly from other sites due to the difference between the Bayswater’s production blast geometry and geology to that of other sites. Using highwall face surveys and Orica’s SUR..YPlus@ software, the average back-break behind normal production blasts was determined. This was then used to select the stand-off distance between the back row production blastholes to the presplit line. While presplit designs are normally based on powder factor (kg/m2), the use of energy factor (MJ/m2) was also investigated as a possible design criteria.

Jan 1, 1999

By Dennis J. Viscusi, James H. III Rowland, Lon D. Santis, Mark H. Weslowski

This paper describes the procedure for analysis of toxic fumes from the detonation of high explosives using the Large Chamber at the U.S. Bureau of Mines (USBM), Pittsburgh Research Center (PRC). This test is specified in 30 Code of Federal Regulations (CFR) Part 15.20 (g) as a requirement for the Mine Safety and Health Administration's (MSHA) approval of an explosive as permissible for use in underground coal mines. The Large Chamber replaced the Bichel gauge and CrawshawJones (C-J) apparatus in the 1989 revision of these regulations. To determine the safety of an explosive in terms of toxic gas production, the Large Chamber Test attempts to simulate mine conditions and miners' exposure to toxic gases from explosives.

Jan 1, 1995

By Byron Groen, Corry Goumans

Description of Project: Project location is at WAC Bennett Dam in Hudson’s Hope, British Columbia, Canada.

Jan 1, 2014

By Alain Blanchier

Because in Europe and in many other countries as well every new project (quarry, mine, public work) needs a risk estimation to prove its feasibility, a model to estimate flyrock risks became necessary. This paper presents the basic hypothesis which should underlay such a model to estimate statistical flyrocks range for not only some single blasts but a whole project and in particular the way to take into account rockmass or blast pattern parameters variability. It describes a first usable quantitative flyrock model based on the characteristics of the blasting plan and of the generic laws utilised in casting and selective blasting operations and on a statistical approach of rockmass. In a second step, this paper discuss an approach of risks estimation compared to the classical one used in pyrotechnics studies for explosive magazine risks assessment.

Jan 1, 2013

By Pierre Allard, Wilfrid Comeau

Near-field and close-in blasting can be safe and efficient, near engineered structures, if the dynamic reaction of structural members to blasting vibrations are considered. Safe particle velocity criteria can be derived from allowable safe static flexural deflections and critical frequencies. Control of close-in blasting can be accomplished using low-pass filtering of the particle velocity signal at the critical frequency. The CETE Mediterranee laboratory at Aix-en-Provence, France, a branch of the Ministry of Roads and Bridges has -pioneered this approach and successfully applied it to major road cuts and tunnels in built-up areas, as well as a major powerhouse expansion project in Africa. This approach is presently being used for a spillway rehabilitation project in Quebec, Canada. This paper exposes- the theoretical aspects and gives case histories of its use. The SCS-15 an automated, peak reading, data acquisition device is described.

Jan 1, 1991

By Jaime Huidobro, Mervin Austin

The effect on an explosive column of the sharp transient stress waves generated during the earlier detonation of adjacent blastholes is of paramount importance to explosives users. Some explosives will sympathetically detonate under these stresses. Others may suffer a transient desensitization, arising from a temporary increase in the density of an explosive beyond certain limits and persisting until the explosive mass relaxes back to the original density. Some explosives are so adversely affected by these stresses that the product suffers immediate and permanent loss of sensitivity. These effects can be clearly seen while blasting in tough conditions such as burn cuts or wedge cuts and in materials, such as coals, that propagate shock waves well.

Jan 1, 1992

By D. Goodings, W. L. Fourney, Bonenberger, R., Uli Leiste

The Dynamics Effects Laboratory at the University of Maryland conducted a series of very small scale tests to measure the impulse delivered to a plate by the detonation of an explosive charge which was buried in saturated sand. These tests were conducted to support a full scale tests series being supported by the Navy (NSWC Indian Head Division) to learn more about loads applied to structures by explosive detonation. For each of the tests being predicted, a series of three tests were conducted at Maryland, one with a 0.203 gm charge, one with a .609 gm charge, and one with a 3.3 gm charge. A high speed digital camera (500 frames per second) was used to record the displacement of the plate as a function of time. From this the initial velocity of the plate was determined and then the impulse delivered to the plate by the explosive. A best fit line through the data was determined for the three model tests conducted and this equation was used to extrapolate the predicted impulse for the full scale tests.

Jan 1, 2005

By Thomas E. Ricketts

An important part of underground mine planning and operations involves the reclamation of working areas after blasting before the mining cycle can continue. This is especially true for mining that must use large blasting operations in the vicinity of extensive underground workings. In an effort to develop a rational procedure for estimating mine damage produced by blasting, underground rock fall has been assessed for a large-scale blasting operation in oil shale. The amount of mine damage has been quantified in terms of manshifts of effort required to reclaim underground working areas after blasting. This has been further broken down into the three main phases of reclamation, i.e., scaling and excavation, rockbolting, and miscellaneous repairs on ventilation, utilities, etc. Different types of openings have also been assessed including level tunnels, incline drifts and rooms. The effect of repeated blasting on mine damage has also been documented with initial blasts producing more damage than subsequent blasts.

Jan 1, 1988

By Paul Worsey, Gillian Worsey

Description of Project:The basic blasting class underground lab at the Missouri S&T experimental mine in Rolla, o., shows the students how to drill, set up, load, and shoot a shot underground. In this case the shot was part of a new ramp to a second level.

Jan 1, 2014

By Duane Skidmore, Calvin Konya

The supply crunch and cost rise for ammonium nitrate (AN) over the past year have been influenced by a number of factors. These include a general inflationary tendency, particularly great cost rises in fuel, and by a market condition in which demand for ammonium nitrate is great and supply is limited. Demand is largely confined to agricultural and explosives uses with explosives subdivided into mining, construction, and quarrying. The projections show that demand may be expected to increase markedly for the indefinite future in the agricultural and mining sectors of the ammonium nitrate market while fluctuating with indicators of economic activity for the construction and the quarrying sectors. Supply is projected to increase with plants being designed and built due to high need levels and commensurately high profit potential but not enough are planned to provide an equilibrium market. Constraints upon supply increases to match demand increases include shortages in the raw material, natural gas, high cost of investment capital, high equipment costs and long construction delays. The result should be, even under optimistic conditions, considerable shortage and resultant pressure for higher prices through 1979 for ammonium nitrate. The best hope for relief in the intervening years appears to be conservation. In blasting operations, the earliest and best proven route to conservation seems to be improved utilization available from application of highest available technology and most efficient current blasting practice.

Jan 1, 1975

By Peter N. Calder, John N. Tuomi

The development of a successful control blasting program for an open pit iron mine in hard jointed rock is described. The objectives and mechanics of control blasting are discussed. Design and implementation procedures, which should have wide application, are given. Small diameter angle hole pre-split blasting, buffer blasting with production holes in front of pre-split lines and in front of strongly defined rock structures, and vibration control of production blasts are dealt with.

Jan 1, 1980