Search Documents

By Cathy Aimone-Martin, Robert Brentar, Brent Meins, James Lauer

Vibration measurements of multi-story structures in an urban environment began 3 years ago in New York City during close-in blasting to adopt correct measurement procedures and recommend revised ground vibration limits that best characterize cracking potential in mid- to high-rise structures. Two broad categories of structures included non-engineered 4- to 6-story multi-family unreinforced brick masonry buildings, built from the late 1800s to around 1930, and post-WWII, high-rise structures of reinforced concrete and steel rising 12 to 40 stories. In-ground vibration limits similar to those recommended by the U.S. Bureau of Mines safe criteria, developed for 1- and 2-story residential structures, are imposed by the New York City Fire Code. However, these limits are often lowered by project engineers or New York Department of Buildings when blasting is planned near buildings designated Landmark or historic and classified as fragile or vibration-sensitive. Seismograph measurements to determine compliance with in-ground velocity limits currently employ geophones mounted to basement walls and on concrete slabs overlying rock. These measurements cannot be correlated with upper structure cracking potential and are often exceeded, resulting in excessive and costly downtime to allow post-blast damage investigations.

Jan 1, 2014

By V. A. Akinbinua

This work is intended to examine the relationship between rock fragments produced during compression tests using a soft testing machine, e.g. hydraulic press (the machine used in this work is Amlser rock testing machine), and the rock fragments size distribution produced by fragmentation of the same rock through application of explosive. The rocks tested are fine grained marble, medium grained tonalite and fine-medium grained granite, medium grained norite and medium grained gabbro. The rocks types are prepared according to ISRM methods to be tested for strength determination. The rocks are loaded at constant load until failure. The fragments resulting from the failure of each of the rocks types are collected for size characterization by sieve analysis. The same rocks tested under soft testing machine are also prepared into blocks of dimension 150 mm length x 100 mm width x 100 mm height for blasting by explosive application. Each block of the different rocks are drilled through with an 8 mm diameter drill to a depth of 80 mm. Each of the holes on the blocks is spaced from each other at 44.7 mm and with a burden of 28 mm. The holes therefore formed a rectangular blasting pattern. Each of the holes was charged with a 720 mg electronic detonator and fired instantaneously inside a cylindrical blasting chamber. After each shot, the fragments are collected for size characterization. The sizes distributions from blasting are compared with sizes distributions resulting from rock testing using the parameter Xc of the Rosin-Rammler distribution function (RR) and 75% cumulative percentage passing. The analysis and finding from this work is presented in this paper.

Jan 1, 2014

By D. Lynn Gordon, Larry B. Weston, Michael W. Manhart, Patrick R. Bowden, Michael W. Redmond

Study of confinement effects on detonation characteristics and subsequent fitting form development as a function of confiner strength and thickness.

Feb 1, 2020

By Pat McLaughlin

Blast design in the construction industry has often been based on past practice or powder factors. This is to some extent understandable, since construction projects do not have the longevity of mining or quarrying operations and therefore have less opportunity to pursue potential improvements. The main concern of the operator is whether or not the technique will work, and at what cost to the downstream processes. Time, not long term savings, is of the essence.

Jan 1, 1994

By Robert Hopler

On June 13, 1912, the final decree of dissolution of the DuPont explosives trust was handed down, and the resulting new companies began operating at the beginning of the new year. The property assets granted to (or retained by) the companies were as follows:

Jan 1, 2014

By Martti Hagfors

Underwater explosions have been used as a test method for the determination of energy content of explosives for several decades. This is the only test method by which shock, gas heave and total energy values can be measured separately. The experimental data can be measured from the pressure-time curves measured by the pressure-recording unit. The shock energy is integrated from the shock peak area and the gas heave energy is calculated from the time interval between the primary shock wave front and the shock wave caused by the first bubble implosion. tb. Bubble period, tb, is the time of first bubble oscillation, the time which passes after the shock peak front to the first bubble peak. The total energy value is the sum of these two partial energies.

Jan 1, 2009

By Tony A. Rorke, Joe R. Brinkmann

The application of instrumentation to better understand and improve production blasting is one of the most fruitful areas of explosives and blasting research. The majority of instrumented studies of production blasting have relied on the extrapolation of far field measurements to postulate blast performance in regions of interest closer to the charge where rock breaking takes place. However, the nonlinear and dissipative nature of the quantities being measured raises serious questions as to the accuracy and validity of such extrapolations.

Jan 1, 1991

By Rhys Baker, Tim O’Brien, Joshua M. Hoffman

This paper discusses this division of power as it relates to the explosives industry. Each branch is responsive to the public and the processes through which each promulgates regulation and legislation require public input in different forms.

Feb 1, 2020

By Shonn K. McNeill, Joshua Micah Hoffman

Security engineering is similar to other forms of engineering – the design is guided by the loads, materials, and desired function. For facility design, the load is the threat. Facilities that are designed with considerations for explosive hazards are designed with a shot, or series of shots, of a given size and distance from key locations. These facilities range from office buildings and industrial sites in developed nations to military and police stations in contingency areas. The challenge is the design shots are not often communicated to facility owners and managers. If the hazards change, whether it’s due to an increased capacity to cause damage by a threat or a decrease in capacity by a structure, not knowing the design shot means not knowing if security design needs to change. Blast modeling is an engineering tool that can be used to reverse engineer what a facility is suitable for, as well as be a tool for modifying security design for new conditions. This paper will examine military and civilian examples, including a case study of a military facility that did not know their as-built conditions and had to be rapidly closed; due to the determination their security engineering shortcomings could not be mitigated.

Jan 1, 2019

By James W. Reil, Douglas A. Anderson, Steven L. Burchell

A total of 26 full-scale production blasts at three sites were extensively monitored with sophisticated instrumentation systems to determine the benefits of "ore. accurate detonators. The new and "ore accurate MS electric Masterdet detonator was tested against conventional detonators to determine any increase in productivity outputs. All blast design parameters between paired blasts were kept as constant as possible with the only difference being the inherent accuracy of both detonator systems.

Jan 1, 1989

By Robert Hopler

DESCENT INTO A COAL MINE From “The Playbook of Metals, including Personal Narratives of Visits to Coal, Lead, Copper, and Tin Mines,” by John Henry Pepper. Published by Routledge, Wa rne, and Routledge, London, 1862 ENGINEERING NEWS New Yor k January 22, 1903 THE BEGINNING OF THE END OF DYNAMITE. In another part of this issue we have reported the results of some test results made upon one of the safety powders. It will pay every c o n t r a c t o r, miner, or user of explosives in any form to carefully re a d the article re f e r red to. Dynamite has done a gre a t work in the service of man, as did black powder before it; but its i n h e rent dangers are admitted by all and are proved by the long list of deaths and injuries, and destruction to property which annually occur through its use. Why should we continue to use an explosive that annually kills and maims hund reds of men, when others are available which are equally powerful, no more expensive and far less liable to accidental discharg e ? Dynamite when first manufacture d is pure and comparatively safe; but most unfortunately it does not always stay pure; it “rots,” and then it is exceedingly dangerous. More than this, the explosive part of dynamite is a liquid, nitro - g l y c e rine, which is absorbed or soaked up by sawdust, wood pulp or the like. So long as this liquid nitro - glycerine remains pure and remains “soaked up,” or absorbed t h e re is little danger. It has been found, however, that the nitro - g l y cerine leaks under certain conditions. During thawing it fre q u e n t l y leaks out of the stick, or if it becomes wet the water causes the n i t ro-glycerine to leak out. In either case free liquid nitro - g l y c e r i n e escapes, and in that free state it may be exploded by any very slight shock. Nor is this all, if a stick of frozen dynamite be bro k e n a c ross it has been found by tests that the frozen nitro - g l y c e r i n e w h e re thus broken is very sensitive to shocks afterward .

Jan 1, 2004

By O Omidi

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper reviews previous experimental information and presents the results of new tests conducted in small blocks constructed using a commercial grout. The effect of the delay on the average fragment size, coarse fragmentation and uniformity of fragmentation is discussed. Fragmentation was coarser at extremely short or extremely long delays, while a fairly constant average size was obtained at a variety of intermediate delays. Uniformity, defined as the slope of the fragmentation distribution through the average fragment size, was poor at short and very long delays and relatively constant at the intermediate delays. Some tests attempted to minimize the effect of gas penetration by lining the boreholes with copper tubes. When this was the case average fragmentation changed marginally, while uniformity was significantly affected by delay and was typically smaller than in the unlined tests.

Jan 1, 2014

By Kyle Ott, Bernard Daly, Syed Haq, Douglas Anderson, Parsons Brinckerhoff

Drill and blast was determined to be the most cost-effective means of excavating the Raw Water Tunnel (RWT) for the Croton Water Treatment Plant in the Bronx, New York City. One of the major issues confronting project designers was the potential impact of blast vibrations on a major City Distribution Tunnel (CDT). The proposed path of the RWT would cross less than 30 meters (100 feet) above the CDT, which was built in 1917. Discussions with New York City Department of Environmental Protection led to vibration criteria on the CDT of 51 mm/sec (2 in/sec) peak particle velocity as an alert level, and 38 mm/sec (1.5 in/sec) as a review level.

Jan 1, 2012

By Aloke Verma, R. Singh, S. Jana, C. Sawmliana, P. Pal Roy

On July 21, 2004, a trial blast using electronic detonators was conducted in India for the first time in an opencast mine at Pundi-E Quarry of TISCO, West Bokaro. Orica-IEL conducted the test using electronic detonators. To provide necessary technical feedback on wider applicability, CMRI scientists also participated in the trial blast.

Jan 1, 2006

By Oliver Finn

Gold dredging has made such rapid strides of late and there is such a widespread interest in this branch of mining that I venture to contribute a detailed account of the way in which a Keystone driller was used by me in California to loosen, by blasting, a very tight gravel deposit, preparatory to dredging. There is a great difference between “cemented gravel” and “tight gravel.” A truly cemented gravel is not a dredging proposition, while the tightest possible gravel, where there is no cement, can be made easy working by the following method of blasting:

Jan 1, 2008

By Alejandro Berrios, Matheus DaSilva, Erick Siqueira

Vazante mine is an underground polymetallic mine that produces zinc, lead, and silver, which belongs to Nexa Resources in Minas Gerais, Brazil. The mine, a sublevel stope underground mine, mainly applies two subvariants: VRM – Vertical Retreat Mining and Open Stope. In a specific place of the mine, the geology allowed the design of a production stope with larger dimensions than the standard stopes, commonly called Super Stope. At this place, the plan was to apply both sublevel variants simultaneously. This mining block comprises rings in two different levels, with access by two ore drives on each level; the dimensions would be approximately 50 meters high, 50 meters long, and 35 meters wide. Opening the Free Face to mine the whole Stope was a challenge due to operational issues, such as hazard risks from loading over void space, exposure to uncontained places, and the impossibility of implementing the optimal blast sequence. Wireless blasting initiators have gained popularity recently due to their convenience, safety, and efficiency. This initiation system was applied to preload all the rings required to open the Free Face, ensuring a safe and optimal blast sequence. Wireless initiation prevented hazard risks, enhanced the blast sequence to guarantee the required void space, and optimized the equipment's operational cycle. The blast crew carried out the activity without exposure to the risk of loading over void space. The wireless detonators also avoided after-blast activities, which were required to provide secure access to the blast crew, optimizing the operational cycle.

Jan 21, 2025

By Ron Beeslaar, Tony Rorke

The Professional Blast Manager is a blast design tool that has been developed in South Africa. It is aimed at mining and civil engineen, blasting contractors and mine planning engineers. The code can be used as a stand-alone package or be combined Into complex mine information systems.

Jan 1, 1998

By B Mohanty, G Yamin

A number of parameters, aside from blast design and pre-existing rock conditions, can change the performance of the explosives system in actual blasting practice. Sympathetic pressures caused by detonation of preceding holes have been identified as a major contributor to explosive system malfunctions, leading to uneven blasting performance. These effects can occur both within a hole or across several holes. These can consist of high transient pressures related to the shock phase of the explosion or the relatively longer or quasi-static pressures associated with the explosion gas expansion phase. This study presents the findings from an on- going investigation on measurement and analysis of these pressures between donor and receptor holes in a granitic outcrop for representative inter-hole distances and borehole conditions, employing single cartridges of emulsion explosive in 45 mm diameter holes. The results, despite wide scatter in the measured values, show the very short duration pressures to range up to 7 MPa and arriving within a few milliseconds after detonation, whereas the much lower amplitude pressures arrive after tens of milliseconds. Both have the potential to seriously affect the performance of an explosives system.

Jan 1, 2005

By Conny Postupack

To make money in mining coal you have to sell it for a lot more than it cost you to get it out of the ground. And yet, every year it cost us more and more to stay inbusiness, while the price we get for coal does not increase at the same rate.

Jan 1, 1990

By Sushil Bhandari, Amit Bhandari

Drilling and Blasting are core operations in a mine. They impact all the downstream operations and their costs. Digital technologies exist for optimizing both drilling and blasting for many years. However, these technologies have largely been non-integrated and non-real time. This gap results in sub-optimal drilling and blasting operations. Also traditionally focus has been on optimizing individual areas (drilling or blasting and subsequent subsystems). Industry has largely lacked real time or near real time integration available to the user in the field and in the office. In this paper, a case study is presented of a large global cement company using a cloud and mobile based platform across 17 of their mines consistently over a large number of users over a period of over two years. The use of a blast platform is detailed which include blast designs, blast data collection and the trends in terms of results. On the drilling side, this paper describes the ability to capture drill logs, plod reports etc. Also actual drilling information in the field using a mobile device and its real time synchronization with a blast designer to provide visibility of expected fragmentation and vibration levels based on the drilling done. Key parameters such as hole ID, design depth, actual depth, hole status, designed and actual charge (length and weight), designed and actual stemming length are captured. The case study also highlights the challenges in technology adoption and implementation in mining in drilling and blasting. Making drill and blast results predictable should be the desired direction. Also digital technology tool adoption has been seen at the biggest miners – not so much in mid-sized miners or drill and blast contractors. Benefits of this platform on the safety side are highlighted including predictions on safety parameters and appropriate alerts if blast safety parameter / clearance zones are not met. The safety parameters are made available visually to the operator using maps and / or on drone images. Future possible improvements in the digital technology platform at the site are also highlighted including greater possible automation.