Search Documents

By Hanns J. Billmayer

This report, which covers the period from April 1975 to November 1975, describes the work performed in compliance with the requirements of Contract No. H0357091. The purpose of this contract was the development of protective canopy concepts applicable to rail haulage equipment used in underground coal mines.

Jan 1, 1976

By Joseph Chalmers

Stimulative methods of production, whereby the total recovery of oil from natural reservoirs is increased, have come into considerable prominence during the past 15 years. In many oil-producing areas properties considered ready for abandonment by ordinary producing methods have responded to some form of stimulation, and their economic lives have been extended. The stimulative method having widest application is the injection of air or gas into the reservoir formations through selected input wells and is commonly referred to as the "gas drive." As a result of the many successful "gas-drive" operations operators are depending more and more upon this method for increasing the ultimate recovery of oil from their properties. A number of factors influence the efficacy of different gases as propulsive agents in recovering oil from sands. Gases of high density and viscosity show a tendency toward a slightly higher efficiency than those of lower density and viscosity. The solubility of the gas in the oil also affects the efficiency of oil recovery. Not only does dissolved gas decrease the viscosity of the oil, but dissolved gas that expands from solution in the oil tends to increase the effectiveness of a "gas drive." Interfacial tension between the oil and the gas and its effect upon the recovery of oil by gas injection are factors of which little is known. Dr. A. G. Loomis expressed the opinion that interfacial tension probably plays a minor role in the recovery of oil, except under conditions that produce a gas-oil foam. In connection with the above physical properties that influence the action of a pressure medium, control of the injected volume of the pressure medium is perhaps the major factor. The rate of gas injection determines to a great extent the amount of slippage and the resulting efficiency of the operation. The importance of volume control is realized when one considers that frequently it is the only factor that is under complete control of the operator.

Jan 1, 1930

By Laurance L. Oden, Jack C. White, Alan D. Hartman

The U.S. Bureau of Mines, under a Memorandum of Agreement with the American Society of Mechanical Engineers (ASME), established design criteria for a facility to field residues from municipal waste combustion. This facility, which is available to potential users on a cost-sharing basis, is also applicable to a variety of inorganic waste materials from smelting or melting operations. The design consists of a mechanical feed handling system, electric arc melting furnace, fume-off gas handling system, and thermal oxidizer for final off gas treatment. Screw conveyors and a bucket elevator deliver up to 2,000 Ib/h of minus I-in material to a three-phase electric arc melting furnace. This unique 800-kVe A furnace has a water-cooled shell and roof to minimize interaction of the melt with the refractory lining. The volume of the hearth below the slag taphole is approximately 1.2 st of steel. The furnace is sealed, allowing atmosphere control within the furnace and fume duct by nitrogen or inert gas injection. A jet-pulsed baghouse removes particulate from the off gas and serves as an acid gas scrubber. The clean off gas is heated to 1,800' F for 1 s in a propane-fired thermal oxidizer before being vented to the atmosphere.

Jan 1, 1993

By R. A. Beall

This paper summarizes the development of a furnace for producing titanium castings. The general problem is outlined and chronological details are given on the construction and operation of four different casting furnaces, all utilizing consumable-electrode arc heating and water-cooled copper crucibles. Of the two methods of pouring, the tilt-pour technique has been more satisfactory than bottom tapping. Mold design, electrode fabrication, and deep-pool production are discussed. INTRODUCTION In the early summer of 1953 the Bureau of Mines was contacted by the Department of the Army through Watertown Arsenal to explore the possibility of conducting research on casting titanium metal. The objective of the program was "to develop a technique for producing formed castings of titanium metal not less than 40 pounds in weight and without introduction of deleterious contamination."

Jan 1, 1956

By G. B. Clark

One portion of this project was to test a blast shield and to design some features for a novel tunneling method termed the Automated Drill and Blast System (ADBS). The ADBS tunneling concept was developed for the design of an excavation system of greater efficiency than conventional drill, blast, and muck (DBM) systems by minimizing the down time and approaching the non-cyclic efficiency of continuous tunneling by means of small charge blasting. Small charge blasting uses simultaneously detonated, small light charges (less than 200 grams per hole) in four to eight shallow (24 to 36 in. deep) holes usually in a line. Limitation of the total explosive per blast reduced air blast overpressure, fly rock velocity, vibration, and noise. Thus, shielded equipment can remain at the face and a tunnel shield permits support personnel to work outby the shield at all times. The ADBS equipment will be composed of five components: (1) a chassis, upon which is mounted automated mucking equipment, and a frame which carries (2) the hydraulic drill(s), (3) load/blast system(s), and (4) control cab(s). The blast shield may have its own mounting. Ventilation, horizontal, and vertical alignment controls are incorporated in the system. The blast sheild, which protects personnel outby the advance equipment from air blast overpressure, fly rock, and gases, was tested with full scale small charge blasting. A blast shield was designed, fabricated, and tested under conditions anticipated for a working model. The shield was designed to expand to fit the tunnel shape, to seal itself to the tunnel periphery, and to contain air blast, fly rock, and gaseous explosion products. In addition, the shield, which was lined on the inby side with rubber belting, reduced the blast noise level outby the shield to 113 dBA or less, which is very near permissible levels. The test results show conclusively that the shield concept is viable. Based partially on the shield tests, a blast resistant control cab was designed to be located on the equipment chassis inby the blast shield to protect operators during blasting, and to contain all the controls necessary for system operation and safety. The economics of tunnel driving using the ADBS were compared with those of DBM. Four rock types, which determine advance rate, and four cost categories were examined. The results of this analysis are as follows: 1. ADBS advance rate is faster because equipment remains at the face and operation procedes semi-continuously. 2. ADBS bit and explosive cost (which accounts for 4%o of the total advance cost) is higher than for DBM. 3. ADBS equipment cost, on a per foot basis, is lower than for DBM. 4. Due to a reduced labor force, ADBS labor cost is lower than for DBM. 5. Because of the overbreak reduction due to controlled blasting, ADBS tunnel support cost is lower than for DBM. 6. On a per foot basis, total ADBS advance cost is from 17% to 20% lower than for DBM, depending on tunnel diameter and rock type. The small charge method greatly reduces ground vibration, increases personnel safety by limiting excessive fracture, and decreases tunnel support requirements by reducing overbreak. The overall analysis, tests, and results to date show that the Automated Drill and Blast System may be developed into a viable tunnel excavation method. The method also may be adapted to use in the mining of ore. For some types of mining operations, the cyclic nature of conventional drill and blast methods may not be a disadvantage, either where the drilling and mucking may proceed simultaneously or where the operations are carried out in adjacent working faces. The proposed method would find application where continuous methods of excavation are desirable.

Jan 1, 1979

By Wils L. Cooley

The report covers several aspects of mine safety ground systems, primarily for underground coal mines. The design of a combined ground fault-ground check monitoring system is presented. An analysis is made of grounding systems for dc shuttle cars. Complete resistance data and results of physical inspections of self-salting ground rods are presented. A detailed resistance and economic analysis is presented for the use of composite materials for building inexpensive and effective ground beds in high-resistivity areas. The desireability of penetrating the coal seam with a borehole safety ground is investigated. A report is made of a Mine Substation Grounding and Bonding Workshop.

Jan 1, 1980

This study estimates costs of producing bituminous coal and lignite by strip-mining methods in 12 hypothetical mines. Basic costs are developed by geographic area, rank of coal, and output capacity. Seam thickness and depth and type of overburden are considered typical for the area in which the hypothetical mine would be located. The cost analyses are based on the use of new equipment, the prevailing union wage scales, and the payment of all miscellaneous costs including royalties, contributions to the miners' welfare fund, and license and permit fees. All model mines are considered to have a life span of 20 years. Capital costs of bituminous strip mines with a capacity of 1 million tons per year range from $12.7 million in the Appalachian region to $16.0 million in the Interior province. The corresponding selling price, assuming a discounted cash flow return of 12 percent on investment, is $5.40 and $6.95 per ton, respectively. For bituminous coal strip mines producing 3 million tons annually, a capital investment of $24.9 million will render a selling price of, $3.46 per ton in the Interior province, whereas a similar mine in the Appalachian region requires a capital investment of $28.0 million to produce coal selling for $4.01 per ton. Subbituminous strip mines of 5 million tons of output per year range in capital costs from $28.7 million in the Southwest to $13.9 million in Wyoming and Montana. Coal produced in the Southwest would sell for $3.03 per ton, while coal from Wyoming and Montana would sell for $1.83 and $1.64 per ton, respectively. The capital costs for the strip mining of lignite range from $6.4 million for an output capacity of 1 million tons annually to $20.7 million for an annual capacity of 5 million tons. The corresponding selling prices of $3.01 and $2.12 per ton, respectively, Indicate the advantages of a large-capacity strip mine.

Jan 1, 1972

By David R. Peterson

This user's manual covers a set of 5 computer codes which were generated during development of a simulation of deep ocean mining operational economics. Table 1.1 provides a summary of these codes, and a more thorough description of each follows, In addition to the descriptions in this user's manual, internal documentation is provided throughout each code, except for the very simple ones, for ease of understanding or possible modification. The two major codes are MINER, which performs the deep ocean mining system operational simulation, and MSWEEP, which calculates the sweep and feed efficiencies for a set of collector paths generated by MINER. The standard operating procedure is to input the system and operating parameters to MINER, which computes a set of collector paths automatically and stores the information in the fife PATH.DAT. MSWEEP subsequently retrieves the collector path data in PATH.DAT, and uses it to calculate sweep and feed efficiency. Separating MINER and MSWEEP allows parmetric execution of MSWEEP without recomputing the collector paths with MINER. PIPEST, RESP, and OBSTCL are special-purpose codes described in more detail in the following documentation.

Jan 1, 1979

By Dipak C. Talapatra

This report describes the development of guidelines for design, inspection and maintenance of automatic couplers. In order to devise the guidelines, performance requirements for automatic couplers were carefully established. This was clone through a comprehensive survey of coupler manufacturers and extensive observation of automatic couplers in service in a broad spectrum of mines. The capability of the couplers to withstand the demands of the mining environment in terms of strength characteristics, gathering range, curve negotiability, and other factors were all carefully evaluated. An analysis of coupler related accidents for the years 1972-1976 was carried out to provide information on the safety and reliability of existing automatic couplers. This formed an important input to the development of the guidelines. It is expected that these guidelines will he useful to coupler manufacturers for establishing designs for improved automatic couplers, and to mine operators for maintaining their couplers in a safe and good operating condition throughout their expected lifetimes. This report is in two volumes: Volume l - Technical Report Volume 2 - Design, Inspection, and Maintenance Manual

Jan 1, 1977

By Lyda W. Hersloff

An environmental monitoring program was established to assess the baseline of parameters which may be impacted by a research and development hydraulic borehole mining operation. During the baseline program, two aquifers were identified at the borehole site with the overlying sand aquifer being distinct from the ore sand aquifer on the basis of radiological parameters. The direction of flow of groundwater was determined to be north 19° west at a rate of 1.82 feet per year. Tests to determine the effect of backfilling the boreholes indicated that using overburden from the open pit mining operation would not significantly increase the radiological consti¬tuents of the ore sand aquifer. Mining measurements of the- radon flux from the borehole indicated that the actual release rate of 0.035 pCi/sec was several orders of magnitude less than the calculated estimate by the Environmental Protection Agency. Finally, a gamma survey conducted at the site indicated that the terrestrial component of background radiation was consistent with that in areas near uranium deposits. The methodology used as well as the supporting data are given in this report.

Jan 1, 1981

By Donald P. Schlick

This Information Circular presents a brief historical digest of the early attempts of the Bureau of Nines and the U.S. Public Health Service to establish coal mine dust exposure standards. It reviews current, accepted standards of the United States as well as available standards of other countries.

Jan 1, 1971

In 1990, the Bureau of Mines (BOM) conducted a mineral investigation of the mines and prospects in the East Mojave National Scenic Area (EMNSA), San Bernardino County, California During field work, BOM identified 701 mines and prospects in EMNSA for which the geology, mineral resources, and mining history were compiled and summarized. Analytical results for 1,188 rock samples collected are tabulated. Total value of identified resources in EMNSA is $5.0 billion. Twenty-four mines and prospects were deemed profitable under current economic conditions. Development could generate considerable economic benefits to San Bernardino County. Potential economic benefits from mining the deposits were evaluated under the following access restrictions for EMNSA: 1) full access, 2) HR 3460, and 3) S 11/HR 780. Under the full access scenario, cumulative mine revenues are $3.0 billion, cumulative personal earnings at mines and supporting industries are $0.94 billion, and annual jobs at mines and supporting industries are 2,379. Under HR 3460, mine revenues, personal earnings, and annual jobs are $2.9 billion, $0.88 billion, and 2,165, respectively. Under S 11/HR 780, mine revenues, personal earnings, and annual jobs are $1.0 billion, $0.32 billion, and 936, respectively.

Jan 1, 1990

By D. Ng

A facility to evaluate the fire endurance of mine stoppings was constructed by the Bureau of Mines in the multiple entry section of the Bruceton (PA) Experimental Mine. Stoppings up to 6 by 18 ft can be tested in a manner simulating mine conditions. The stopping is subjected to a 70-min liquid fuel tray fire with an energy output of 75,000 Btu/min. The stopping and adjacent areas are instrumented with thermocouples and heat flux gauges. Data acquisition is by an automatic data logger capable of continuously recording over 100 channels of information. Two 8-in-thick concrete block stoppings and a galvanized steel stopping were tested. A crack developed on the fire side surface of the block stoppings where the flames were most intense. However, the temperatures of the unexposed surfaces of the stoppings never exceeded 800 C and the surfaces were undamaged. The steel stopping retained its structural integrity during the test. The temperature of the unexposed steel surface reached 5000 C, but combustible materials located 1 ft from the surface did not ignite. A 3/4-in-thick coating of construction plaster was applied to the fire side of the previously tested uncoated steel stopping. The quantity of heat energy transmitted across this coated metal stopping was reduced approximately 50%. All stoppings prevented the passage of flame and smoke.

Jan 1, 1988

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) In-shaft equipment design and specification criteria are considered as they influence guideline preparation. (b) A comprehensive review of hoist electric drives and controls as applied to mine hoists is set forth with special reference to duty cycle calculations and their effect on electrical component selection.

Jan 1, 1988

By Marshal Scherba

Coal seams approximately 7 feet, 9 feet and 20 feet thick at depths of 250, 600 and 1,000 feet respectively were detected using high resolution seismic reflection techniques. Investigation of seismic profiles indicates that good data are required to delineate faulting with only 20 feet of throw but that faulting with 50 feet of vertical displacement can be detected with poor data. Data acquired from dynamite charges fired in water saturated media were clearly superior to that acquired using charges dry tamped in 10 and 20 foot holes.

Jan 1, 1977

By J. R. Allsup

Air pollutants in exhaust gas produced from LP-gas (propane) were studied using both laboratory engines and vehicles. The objective of the study was to evaluate engine parameters relating to the advantageous use of propane as a low-pollution fuel. Some comparisons are made between gasoline, natural gas, and propane. Results show that engines can operate over a wider range of A/F with minimum carbon monoxide and hydrocarbon emission when using propane than when using gasoline. Mixture enrichment using propane is unnecessary during cold starts, thereby eliminating the emission penalty during warmup. Carbon monoxide and hydrocarbon emission using propane are unaffected by ambient temperature. The photochemical reactivity of hydrocarbon emission is considerably lower with propane than with gasoline.

Jan 1, 1972

By Charles E. Whieldon

Because of the importance of recovering more oil from known petroleum reserves, increased emphasis has been placed on the application of secondary-recovery methods. It is hoped that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases. Previously published reports3 4 5/ have described the results of water-flooding in Roane, Pleasants, and Wetzel Counties, W. Va. (fig. 1). This report describes the South Penn Oil Co. Yawkey waterflood property, Berea sand, Griffithsville oilfield, Duval District, Lincoln County, W. Va. (fig. 2).

Jan 1, 1961

By D. D. Southworth

In 1981, 1982, and 1983, the Bureau of Mines examined the potential for lode deposits of platinum-group metals (PGM) in the Goodnews Bay ultramafic complex, Alaska. The complex consists of the Red Mountain, Suzie Mountain, and Smalls River ultramafic bodies and displays concentric zoning of rock types similar to complexes in southeast Alaska, British Columbia, and the Ural Mountains in the U.S.S.R. Results of the study indicate that platinum is preferentially associated with chromite and magnetite in the dunite core of the complex, and palladium is preferentidlly associated with sulfide minerals in the outer clinopyroxene-rich zones. the most promising targets for PGM lode deposits are the chromite-rich dunite at the heads of Fox Gulch and Squirrel Creek and iron-nickel and iron copper sulfide-bearing magnetite clinopyroxenite and hornblende-rich rocks outward of the dunite core, also in the Fox Gulch-Squirrel Creek area. Significant placer reserves are present in the unmined, deeply buried placer ground in the lower Salmon River Valley, and also in tailings from previous dredging.

Jan 1, 2011

By B. F. Naylor, C. H. Shomate, F. S. Boericke

"Ilmenite is the most important titanium-bearing constituent of titaniferous iron ores. Such ores, of which the United States has abundant reserves, are of interest because they constitute an important potential source of both iron and titanium that may be tapped in times of stress, and which eventually may be utilized in the normal course of events.As the iron and titanium constituents of titaniferous iron ores are not completely separable from each other by ore-dressing methods, any process for metal recovery will, of necessity, involve reduction of the iron in ilmenite. Consequently, knowledge of the thermodynamic properties of ilmenite should supplement information already available concerning those ores. With this in view, the Pacific Experiment Station of the Bureau of Mines undertook to evaluate thermodynamic properties; the data obtained are the subject of this report.Three types of experimental work were involved. First, low-temperature specific heats of ilmenite were measured in the temperature range 500 to 29S° K. These data serve to evaluate the entropy, a quantity necessary for a reliable evaluation and correlation of other thermodynamic properties. Second, high-temperature heat-content measurements were made in the temperature range 298° to 1,743° K. The data serve to bridge the gap between room temperature and elevated reduction-process temperatures. Finally, hydrogen-reduction equilibria were measured in the temperature range 1,220° to1,375° K. These data-give a direct measure of the free energy of reduction of ilmonite at these temperatures and, in conjunction with results of the other two types of measurements, serve to obtain the heat of formation of ilmenite, a quantity not readily determinable by direct calorimetric means.The data are correlated to form a composite, self-consistent portrayal of the thermodynamic properties of ilmenite, which may be used in evaluating the efficacy of any reducing agent of known thermodynamic properties. Selective-reduction of iron in ilmenite by hydrogen, carbon monoxide, and carbon are considered in this report."

May 1, 1946

By Dana T. Updyke

An evaluation was made of one of several improved underground communication systems sponsored by the U.S. Bureau of Mines. The system evaluated was installed in a typical metal/non-metal room and pillar mine and utilized UHF repeaters connected to a unique distributed antenna and passive reflector system which provided mine-wide communications. A microprocessor controlled data collection system was assembled and installed for the evaluation. Data consisting principally or times and durations of messages and identities of the originating transceivers was collected between February and August of 1982 (6 mos.). Analysis of the data shows that the principal benefits are reduction in time required for unscheduled maintenance and repair, enhancement of safety, and better coordination of production activities. A cost benefit analysis shows a net benefit over cost, although it is also concluded that the capacity of the system is greater than can be justified by current activity in the mine.

Jan 1, 1983