Search Documents

By John R. Benham

The Windigo Theilson RARE II area has a low mineral potential. There are no mines or claims in the area. The only observed results of mining activities were five prospect pits near Tolo Mountain. Samples from these pits contained no significant assays. The study area contains more than 190 million cu yds (145 million m3) of cinders in 17 cones. Development of these cinders is unlikely because their locations are remote, and other sources supply area needs. The Geological Survey has classified the area as prospectively valuable for geothermal resources. However, there has been no geothermal exploration activity.

Jan 1, 1982

By A. J. Farstad

The principle objective of the research effort described herein was to identify as rapidly as possible a practical trapped miner location system. Much effort has been expended in the past on the development of a highly sophisticated seismic location system [1] for trapped miners. Field tests of this system have shown that the location accuracy is limited by a combination of seismic velocity anomalies, timing errors, and in general by the relatively weak nature of the signals received at the surface. It was first felt that similar propagation anomalies would be experienced by electromagnetic systems, but to a greater extent than the seismic. However, preliminary tests performed by Westinghouse on the Operations and Maintenance Program, Contract No. H0210063 in 1971 and 1972, indicated that an electromagnetic solution to the location problem may be more feasible than a seismic solution. Thus a more concentrated effort was launched in 1972 and 1973 to more completely determine the feasibility of electromagnetic location systems for trapped miners. Two different approaches to the location problem were undertaken on this program: (1) A pulsed electromagnetic system was developed by the Special Systems Division of Westinghouse in Baltimore, and (2) a Continuous Wave (CW) System was developed by Westinghouse Georesearch Laboratory (WGL) in Boulder, Colorado. Part I of this report will deal only with the development and results of CW Location System developed by WGL. The CW Location System was field tested at three eastern coal mines and at one western hardrock mine. The maximum overburden depth penetrated during these tests was 990 feet at the Robena No. 4 mine near Waynesburg, Pennsylvania. The earth conductivity at this mine was measured to be 1. 1X102 mhos/m, which combined with the deep overburden make this mine representative of expected worst case conditions for a coal mine EM location exercise.

Jan 1, 1973

By Charles Anema

The Mancarried and Helicopter Receivers were developed under the contract for trapped miner location. This program was a five phase program with 15 mancarried and 5 helicopter production receivers delivered under Phase IV and equipment documentation required under Phase V.

Jan 1, 1976

By Marvin S. Seppanen

Computer programers are often required to make modifications to unfamiliar Fortran routines. This Bureau of Mines report describes a computer program designed to aid the programer in such a situation by reorganizing: Fortran routines. This reorganization includes a sequential renumbering of the routine's statement numbers, a sequential renumbering, and relocation of format statements, an alphanumeric reordering of dimensioned and typed variables, a uniform pattern of text spacing, and a sequential numbering of the records in the final Fortran routine. The computer program has been extensively tested by the author and has proved to be a valuable tool for reorganizing Fortran routines developed under contract and later utilized by the Bureau, and for preparing routines for publication.

Jan 1, 1975

By Forrest T. Moyer

The National Safety Competition was inaugurated in 1925 by the Bureau of Mines, U.S. Department of the Interior, in cooperation with the Explosives Engineer. In the first nationwide contest, 210 mines and quarries were enrolled. In 1962, the thirty-eighth anniversary of the competition, 910 mines and quarries were enrolled. These participating plants were worked a total of 133,292,989 man-hours. Of the enrolled plants, 415 achieved injury-free operations for the year, the largest number of perfect safety records in the history of the contest.

Jan 1, 1964

By E. M. Frost

"A new apparatus has been devised for quickly and precisely analyzing natural gas for its helium content. The following outstanding advantages make it far superior to any equipment now available for the purpose.3/4/5/6/1. It enables more rapid determinations to be made.2. It has far greater sensitivity than previous apparatus. 3. It is portable.Fifty or more samples may be analyzed in an 8-hour day with the new apparatus and procedure. A maximum of about 10 samples per day could be analyzed with previous apparatus. In the apparatus described, the volume of pure helium obtained from a sample is determined by measuring the pressures created by that pure helium when it is expanded into a constant calibrated volume. In older methods the pure helium separated from a sample is pumped into a burette and measured at atmospheric pressure. The new apparatus and Procedure used with it reduce the average time for an analysis from about 40 minutes to less than 10 minutes,Samples containing a few thousandths of a percent helium may be analyzed as readily as samples containing 1 percent or more, This was not possible with former apparatus. Duplicate samples containing a few thousandths of a percent helium have been analyzed, results checking to one ten-thousandth of a percent. Attempts to measure a corresponding volume of helium in a burette at atmospheric pressure become futile. The ability to determine very small quantities of helium has become of great importance recently in gas- and oil-field engineering studies such Os the utilization of helium as a tracer gas in following the movement of gases through underground structures.A complete apparatus was recently carried more than a thousand miles in a passenger automobile. It arrived without breakage, was .set up and ready to make an analysis in a few hours. .Former apparatus was not portable. The portability of the present apparatus permits taking the apparatus to the field for more efficient prosecution of field engineering problems. The only services required in the field are electricity, tap water, and a source of liquid air or liquid nitrogen.The principle involved is based upon the fact that large volumes of all the constituents usually found in natural gas, except helium, are adsorbed quantitatively on cocoanut charcoal that has been cooled to the temperatures of liquid air. A volume of sample is measured and transferred to a tube of cocoanut charcoal maintained at the temperature of liquid air. After adsorption of all the constituents other than helium, the charcoal tube is connected to a sensitive pressure-measuring device, and the Percentage helium originally in the sample is calculated from two pressure readings and the volume of the original sample."

Jun 1, 1946

By L. C. IlsLey

A list of permissible mine equipment approved by the Bureau of Mines before January 1, 1940, was published in Bureau of Mines Information Circu- lar 71103. Information Circular 71584, published as a supplement thereto, listed equipment approved during the calendar year 1940. The present list contains the information given in those two circulars, as well as approvals issued during the calendar year 1941. It embraces electrically operated air compressors, coal drills, conveyors and loading machines, electrical equipment for mine fans, mining machines and trucks, mine pumps, rock- dust distributors, room hoists, storage-battery gathering and haulage locomotives, storage-battery power trucks and shuttle cars, mine telephones, junction and distribution boxes, electric cap lamps, flame safety lamps, electric hand and trip lamps, electric flood lamps, flashlights, methane detectors, and single- and multiple-shot blasting units. The equipment listed is not approved by the Bureau of Mines until found by inspection and test to comply with minimum standards of safety as outlined in "schedules" prepared upon the basis of many years of ex- perience in dealing with safety problems confronting the coal-mining in- dustry. The use of such equipment in mines that are known to be gassy,. as well as in those that may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept informed as to the many types of machines, devices, and lamps that are available for reducing explosion and other hazards incidental to coal mining.

Apr 1, 1942

By W. T. Wertman

LABORATORY research has been started at the Bureau of Mines Morgantown Petroleum Research Laboratory, Morgantown, Va., to investigate the possibilities thermal-recovery methods for producing crude oils of high API gravity found in oil reservoirs of the eastern United States. This bibliography on thermal methods of oil recovery was compiled as a part of the work. Crude oil discoveries to December 31, 1958, in the United States were estimated to exceed 270 billion barrels. Cumulative production of crude oil through 19.55 was about 60 billion barrels, and the American Petroleum Institute estimates that an additional 30.5 billion barrels are economically recoverable by present methods. On this basis, about two-thirds of the oil that has already been found can be classified as economically unrecoverable for lack of a satisfactory method. The rap icily rising costs of proving new deposit; of domestic petroleum, the lack of new discoveries of large oilfields in the united States, and I he growing demand for crude oil have caused an acceleration of research to develop new or improved methods fur producing "unrecoverable" oil in known reservoirs.

Jan 1, 1960

By Martin J. Gavin

"Before discussing oil shales it may be well to consider briefly the conditions surrounding the petroleum industry in the United States, because these largely explain why so much interest is being manifested in oil shales. The United States is not only the greatest producer of petroleum in the world, its output amounting to about 65 per cent of the world's total production; but is also the world's greatest consumer, using more petroleum than it produces within its own borders. For the past four or five years it has been necessary to import oil at a continually increasing rate to make up the deficit between domestic production and domestic consumption. Experts who have made a close study of the future supply and demand for, crude petroleum are satisfied that under present production practice and with the development of possible undeveloped productive areas, the gap between domestic consumption and production will steadily .increase.As possible solutions for the impending domestic shortage of oil, various expedients are receiving attention. These may be grouped under three heads, as follows:(1) Temporary measures, such as curtailment of consumption, development of more efficient methods of production, and more efficient utilization of supplies of petroleum still available. It is unlikely that there will be any great curtailment in consumption of petroleum in the United States; rather, consumption will continue to increase unless a real shortage of oil actually forces curtailment of consumption. The other two possibilities mentioned deserve, and are resolving, serious thought. Much experimental work along these lines, some of which has already yielded excellent results, is being done. Obviously, however, any of these remedies are temporary ones only, so far as regards domestic production of petroleum."

Oct 1, 1920

By H. B. Jensen

STUDY of the thermal-solution process was begun by treating crushed oil shale in a small autoclave at temperatures of 700° to 950° F. The effect of temperature, reaction time, type of solvent, and richness of shale upon the amount of organic matter that was removed from the oil shale was thus determined. Following this orientation work a semicontinuous, bench-scale apparatus was built so that heated solvent could be pumped through a bed of shale under elevated pressure, thus removing the converted organic matter from the spent shale. After some operating experience had been gained, a continuous unit was constructed. This permitted treating a slurry of shale oil and pulverized oil shale at about 300 p. s. i. and temperatures of 750° to 850° F. for various retention times. Considerable cracking and polymerization of the shale oil were found to take place during the process. In an attempt to prevent this, a study was made of extraction of the shale in batch-type autoclaves under high partial pressures of hydrogen at total gas pressures of as much as 4,300 p. s. i. at 850° F. The thermal-solution process was found to convert over 90 percent of the organic matter in oil shale to oil and gas. The highest yields of gas and oil obtained without hydrogen pressure were equivalent to 119 weight-percent of those obtained from the same shale by Fischer assay. With a high partial pressure of hydrogen, yields equivalent to 126 weight-percent of Fischer assay were obtained. However, the oil produced by thermal solution has a higher boiling range than that obtained by other retorting methods, particularly so if the thermal-solution process is used without a high partial pressure of hydrogen. Nondistillable oil (all benzene-soluble material that would not distill under 2 mm. Hg absolute pressure without cracking) equivalent to over 100 percent of the organic matter in the shale was obtained without hydrogen pressure in the system. When the process was carried out under hydrogen pressure, the yield of nondistillable oil amounted to 60 to 70 weight-percent of the organic matter. Part of this heavy material is formed partly by polymerization and condensation of the shale-oil solvent used. These reactions, as well as cracking of the solvent to form gas and a carbonaceous deposit on the shale, are unfavorable features of the process.

Jan 1, 1953

During the second quarter of 1983, the economic recovery showed further strength abetted by the performances of consumer spending, residential investment, and the slowing down of inventory reductions. Real gross national product (GNP) increased from the first to second quarter at an annual rate of 9.2 percent, compared with 2.6 percent from the fourth quarter of 1982 to the first quarter of 1983 and an overall 1.9- percent decrease in 1982. Total industrial production increased 1.8 percent in July, and productivity as measured by output per man-hour increased 1.3 percent between 1982 and the first quarter of 1983 (table 1). Especially noteworthy .was the performance of real consumer durable goods expenditures, which increased at an annual rate of 32.0 percent from the first to the second quarter (about half of the increase consisted of automobile sales) and real consumer spending, which increased between these periods at an annual rate of 9.7 percent. Residential investment increased at an annual rate of 76.1 percent between the first and the second quarters,1/ and private housing starts by about 38,000 units in both March and May.

Jan 1, 1983

By Harvey Patashnick

Current state-of-the-art microweighing technology represented by the Tapered Element Oscillating Microbalance (TEOM) is utilized as the basis for a new generation of Personal Dust Exposure Monitors (PDEM's). Two design configurations are presented. The first is an end-of-shift analysis system which uses small TEOM-PDEM cannisters that replace the filter cartridges in the current PDEM system. All other components carried by the miner (cyclone preseparator and pump) are the same. After the shift the TEOM cannister is plugged into an interface box which enables a minicomputer to automatically identify the unit, determine the dust mass increase during the shift, compute the shift average dust mass concentration, and print out and/or store the data. The second design is a real-time TEOM-PDEM system which is capable of operation over a 10-hour shift and on demand display real-time dust concentration level, time weighted average, and shift average concentration. As a result of the design study, a prototype end-of-shift analysis system was fabricated and delivered to the Bureau of Mines. A description of this system which consists of six TEOM cannisters, interface electronics and minicomputer is given. The system represents a significant advance in the dust monitoring program in terms or accuracy and automation.

Jan 1, 1983

By Jeffrey P. Schubert

The study site in northeastern Illinois underwent surface mining for coal in 1943 and was reclaimed by the state of Illinois in 1972-1973. Additional soil amendments and seed were applied to the spoil surface in 1975-1980. Previous studies in 1975-1978 had shown that the surface spoil materials and five final-cut lakes at the site were quite acidic and the lakes contained high concentrations of sulfate and dissolved metals. Surface runoff water from monitoring plots in 1976 were only moderately acidic and the mean concentrations of most dissolved metals and sulfate in the runoff waters were less than 25% of the concentrations found in Lake B. By 1980, vegetation had become well established over most of the mined area. However, the five final-cut lakes (Lakes A-E) remained acidic. The purpose of the study reported here was to determine the physical and geochemical subsurface conditions of the spoil materials, the hydrologic flow system within the spoils, and the magnitude of acidic spoil leachate migration into the lakes and into the wetland prairie north of the mine site. Lakes A, B, C, and E were still very acidic in 1980-1981 (pH range: 2.9-3.4; aridity range: 110-860 mg/L as CaCO3). Lake B had the worst water quality, with mean concentrations of dissolved aluminum, iron, manganese, and sulfate of 75, 25, 37, and 3340 mg/L, respectively. Shallow groundwaters in spoil materials around Lake B had a lower pH and about two to four times greater concentrations of aridity, aluminum, manganese, zinc, and other metals and nearly 20 times greater dissolved iron than the water in Lake B. The shallow groundwaters in undisturbed soils and bedrock 10-30 m north of the mine site spoils generally were alkaline, but did contain occasional moderately high sulfate and metal concentrations. Pumping tests and recovery tests conducted in piezometers showed hydraulic conductivities of spoil materials ranging from less than 10- to 10-5 m/s; hydraulic conductivities of natural soils and bedrock were measured between 10-10 to 10-7 m/s. Water levels in spoil materials increased rapidly in response to rainstorm events and the recession curves were relatively quick to decline, lasting only two or three days. Quick infiltration of rainfall into the spoil surface and percolation down to the water table caused a rise in groundwater levels and movement of spoil groundwater into the lakes. This groundwater component in the lake water budgets could account for most of the water quality problems occurring in the acid lakes.

Jan 1, 1984

By C. C. Stevenson, Thomas Varley, E. P. Barrett, ROBERT H. BRADFORD

The art of treating ores by the chloride volatilization process is still in the experimental stage. The process has not been sufficiently developed along metallurgical lines to warrant a definite statement as to the exact place it will occupy in the industry. The basic theory of the process has received the attention of prominent metallurgists for 20 years, and considerable research and experimental work have been carried on. Much of the experimental work done has never been published; if the accumulated results were made known, they would greatly aid,. the further development of the process. This bulletin aim~ to bring the salient features of the process to the attention of metallurgists for the purpose of furnishing information to and receiving comments from interested parties with the ultimate hope that the process will be a commercial success. If commercially utilized, the process will fill a long-felt want in metallurgy, especially in the treatment of oxidized and semioxidized or" carbonate" ores of copper, lead, and silver. Such ores are difficult to treat by gravity concentration or by flotation: in the former their tendency to slime upon crushing and their being of lower specific gravity than the sulphide minerals cause serious losses; in the latter much has been done in sulphidizing oxidized ores and subsequently recovering the artificial sulphides by flotation. Difficulties in proper sulphidizing and the low recoveries obtained have not balanced the cost of the treatment in many plants and in very few has it proved successful. Evidently there is a big void to fill in the treatment of these ores. No radical changes in present methods are forecast, but it is obvious that chloride volatilization can have a distinct place as a method of treatment for ores that are not readily amenable to present methods. In many plants it might replace concentration methods, especially where part of the mineral content in the ores exists in forms other than sulphides.

Jan 1, 1923

By Richard H. Bares

The general or macroclimate of the study sites in western North Dakota is characterized by rapid and sometimes extreme daily and day-to-day temperature fluctuations, rainfall patterns which are erratic in spatial and temporal distribution and intensity, generally low relative humidity, plentiful sunshine, nearly continuous air movement, and a relatively short frost-free period. Of particular relevance to plant growth and productivity is the mosaic of microclimates: these microclimates are affected by landform (convex and concave surfaces); exposure; slope angle, length and aspect; soil color, texture and surface cover (litter), and vegetation cover. The most critical plant growth governing factor in this region is available water. It is determined principally by water input (precipitation) and water loss (evapotranspiration) which is increased by high temperatures, wind, and poor litter and vegetation cover. While spring and fall precipitation is generally gentle and soil-soaking summer rains frequently come in the form of intensive, soil-washing, localized convective thunderstorms of short duration. Due to the convective nature of these storms, summer rainfall is particularly affected by regional topography; southwest slopes and crests often receive more rainfall since these storms usually move in a northeasterly direction. The water loss due to runoff and consequent soil erosion arc major problems resulting from such "cloudbursts". Previous fall precipitation (September - October) when added to current seasonal precipitation (March - August) was found to be significantly correlated (r-.93) with plant production. Winter precipitation (snowfall) is relatively light as the prevailing weather is dominated by dry polar air masses from the north. The nearly continuous wind is responsible for removing snow from open exposures and depositing it in depressions and windbreaks. Although the winter precipitation is not a large component of the total annual precipitation, conservation of that which does occur would contribute to plant production during the following growing season. Generally clear skies over the region facilitate receipt of abundant sunshine at the earth's surface. While good for early season soil warming and plant photosynthesis, this abundant sunshine coupled with long days and nearly continuous wind is responsible for evapotranspiration exceeding precipitation by an average of six inches between June' and September. On a local (micro) scale, the water deficit is most severe on the southern exposures which receive the most direct (most effective) solar radiation and therefore are warmer than other exposures. On a broader scale, it was found that ambient temperature extremes were slightly but significantly greater in the town of Beulah in the Knife River Valley than at the upland test sites, This may have been due to the difference in topography and/or the "urban heat island" effect. It is known that air temperatures in large cities may be 2° to 4°C higher than that of the surrounding countryside. It is also well known that basins, depressions or valleys are sinks for cold air masses and are often subject to frosts not occurring on adjacent upland sites.

Jan 1, 1982

By M. L. Whisman

The Bureau of Mines developed and tested in the laboratory several innovative techniques for reclaiming used lubricating oil. These processes included percolation through both chemically treated clay and ion-exchange resins, distillation through batch and continuous wiped-wall vacuum apparatus, treatment with solvent extraction systems, and chemical removal of impurities with chelating agents. In each treatment, the criteria of evaluation was oil recovery and reduction of acidic and metallic components. Both vacuum distillation and solvent treatment ranked high in their abilities to remove acidic and metallic components of the used oil with good oil recoveries. A combination of the two techniques gave the best overall results in terms of quality evaluations made by established bench tests. The methods were not ranked according to economic practicablity.

Jan 1, 1974

By William W. Aljoe

This report summarizes the Bureau of Mines noise-control research program from 1972 to 1982. Each segment of the mining industry--under- ground coal, underground hardrock, surface mining, and processing plants--has different noise-control problems because of vast differences in working procedures, equipment, and workplace design. The Bureau has identified the most serious noise problems in each segment and has developed strategies for attacking these problems. This publication points out the need for noise control in the mining industry, discusses Federal regulations governing worker exposure to noise, and describes the Bureau's overall approach to mining noise- control research. It traces the history of noise overexposure in each segment of the mining industry and discusses the major noise sources. It provides detailed information on noise-control research efforts in the Bureau's major areas of emphasis, including the results of these efforts. Finally, the report discusses the Bureau's future role in research on mining noise control, emphasizing the need to expend more effort on long term in-house investigations into the noise problems that have been identified in past programs as the most serious ones.

Jan 1, 1985

By K. C. Dean

Changes in the types of materials used for the construction of recent automobile models have occasioned a review of the continued applicability of current recycling techniques. Plastics are being used increasingly in late model cars. To evaluate the changes occurring, a 1972 Mercury Montego, furnished by the Ford Motor Co., was completely dismantled and analyzed, and the composition was compared with that of a composite automobile from 15 vehicles ranging in date of manufacture from 1954 to 1965 and designated as a circa 1960 model. The composite vehicle contained about 26 pounds of plastics, while the 1972 model contained over four times that quantity. The increasing use of plastics in automobiles suggests that research to improve the economic potentiality of plastics recycling is warranted.

Jan 1, 1974

By C. J. Wilhelm

The Bureau of Mines, under its cooperative agreement with the Kansas State Board of Health, has been conducting a study of the various methods of oil-field brine disposal in the oil fields of Kansas. A previous report5/dealt with this problem in the Ritz-Canton field, McPherson County, Kans. A preliminary survey of the Arkansas River drainage area in western Kansas was made during November and December 1934 and January 1935, and a second survey was made approximately one year later during the months of December 1935 and January and March 1936. In addition to the data on the production of oil and 'brine in the various fields and the methods used for handling the brine, the surface drainage and character of the surface soil in the various oil-producing areas were studied.

Jan 1, 1936

By Fred D. Wright

The objectives of this research were: 1. to determine the stability relationships of coal mine roof rocks which are cut by fractures or intersecting joints with and without roof bolts, under various sets of conditions including horizontal formation pressures, inclination and coefficient of friction of joints, bolt loads, roof spans and rock properties; and 2. to develop criteria for the design of roof bolt sys terns for such roofs. The problem was studied by mathematical finite element models and by laboratory models. From the results of the mathematical and laboratory models, equations were derived to express the relationships listed above for cracked, single-layered roof beams and design tables for such beams are included. The analysis was then extended to include multi-layered cracked beams reinforced by roof bolts and a method for analyzing and designing bolting patterns for such roof rocks is presented.

Jan 1, 1974