Search Documents

By M. B. Royer

Sulfur is present in many ores and other raw materials that are used in the production of metals and alloys of industrial importance. Its presence, especially in ferrous-metal products, generally is undesirable because of its detrimental effect during processing and upon various physical properties of the finished metal. Therefore, various methods are resorted to for elimination of the element to some specified maximum final content. Such removal or elimination of sulfur is designated as desulfurization.

Jan 1, 1948

By R. B. Tippin

The heavy liquid separation (HLS) process was investigated by the Bureau of Mines to develop a means of concentrating minerals from natural ores, Various spodumene ores were tested in a 0.4-inch diameter cyclone using pure tetrabromoethane (TBE) as the heavy liquid. Studies were initiated to examine the influence of (1) pulp density (2) feed grade, (3) cyclone pressure, (4) cyclone apex opening size) (5) cyclone vortex finder opening sand (6) mineral particle size on the separation efficiency. Each of these factors was found to affect the heavy liquid separation in some degree; the mineral particle size exhibited the greatest effect and the ore feed grade the least. Conditions necessary to yield an 85 percent spodumene concentrate with an 85 percent recovery were determined to be: 70 psig pressure, 10 percent solids, 0.08-inch apex opening, 0.11-inch vortex finder opening and a minimum amount of minus 200-mesh fines in the feed. Operation of multiple cyclones in series resulted in spodumene concentrates assaying over 90 percent and indicated mineral recoveries exceed-in 90 percent.

Jan 1, 1967

By Blade O. C.

This report is one of a series made by the Bureau of Mines under a cooperative agreement with the Coordinating Fuel and Equipment Research Committee of the Coordinating Research Council, Inc., on the characteristics of commercial aviation gasolines. The series of surveys is a continuation of like work conducted from 1940 to 1946 by the National Bureau of Standards under a similar cooperative agreement. A list of reports of previous surveys is given at the end of this paper.

Jan 1, 1950

By Clayton R. Morlock

Airblasts have been monitored at four coal strip mines and at a limestone quarry. Thirty-seven production blasts have been monitored with three seismographs, resulting in one hundred and eleven complete air pressure records. Instrumentation selection use is described. Data analysis includes an assessment of the predictability of peak overpressures by means of the cube root scaled distance law. It is found that predictability for the cases studied here is not good. An extensive discussion of possible explanations is included. A detailed analysis of the frequency content of the observed airblasts, of considerable importance in evaluating potential annoyance problems, has been made for all records. A computer program has been written to simulate airblasts induced by multiple-hole blasts. A series of small experimental blasts have been detonated and monitored in order to allow an assessment of the program. It is clear that airblasts, especially when induced by very small charges and monitored at very close distances, are highly sensitive to detonation times. Retrofitting of airblast records occasionally was possible, but considerably improved field work is required to validate or refute the computer model.

Jan 1, 1983

By R. Lusignea

A device has been developed for nondestructive testing the holding power of split tube friction rock supports. It operates by measuring the amount of decrease in internal volume when the support is forced into the drilled hole. The pullout force or slip load is a function of this decrease in volume. The device gives readouts of the average internal diameter and predicted pullout force or the support. Laboratory and field tests showed excellent repeatability and good correlation between predicted and actual pullout force. The device is hand-operated, lightweight (7.5 lb) and can be used on any friction support.

Jan 1, 1983

By C. M. McCulloch

The natural vertical fracture system in bituminous coalbeds is called cleat. Cleat orientation commonly controls the direction of mining with major development paralleling the face cleat. Previous researchers have categorized the origin of cleat as endogenetic, relating the origin of cleat to compaction and coalification, and exogenetic, relating the origin of cleat to tectonic forces. In the coalbeds studied for this report it was found that tectonic forces were the controlling factor of cleat formation. Face cleats were formed as extension fractures during structural deformation, and butt cleats, as release fractures during erosion and uplift. The face cleat of the Pittsburgh coalbed rotates from N 80° W in north-western West Virginia to N 57° W in southwestern Pennsylvania; the face cleat maintains a perpendicular orientation to the shifting axial trend of local structures. Cleat orientation in other bituminous coalbeds in Virginia, Utah, Oklahoma, and Central Pennsylvania showed a similar relationship to local structure. Directional permeability of coal is directly related to cleat. Holes drilled perpendicular to the face cleat yield from 2.5 to 10 times the amount of gas released as compared with holes drilled perpendicular to the butt cleat.

Jan 1, 1974

By R. W. Huber, R. C. Wiley, V. C. Petersen

"Three arc- melted ingots, two of a t itanium-7 percent manganese all oy and the third of unalloyed titanium, were forged and rolled into 3/ 4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties.These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots.INTRODUCTIONArc -melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Perk, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.Considerable data have been published recently on constitution diagrams and properties of titanium-manganese alloys in genera1. 3/ 4/5/6/ However, little if any correlation between processing schedules and end results has been published, particularly with respect to the present commercial production of the proprietary titanium manganese alloys . Several factors in the production of titanium and titanium alloys have a pronounced influence on the physical and mechanical properties of the finished product: (1) The degree and nature of impurities in the base materials, ( 2) the amount of impurities introduced during the melting cycle and their distribution, (3) the homogeneity of the alloy, (4) forging, (5) rolling, and ( 6) final heat-treating cycles. All of these item£ are important from a metallurgical standpoint in producing the desired end properties in the metal."

Mar 1, 1955

By I. F. Avery

The productive capacity of natural-gasoline and cycling plants in the United States on January 1, 1958, was 48.8 million gallons per day, according to the Bureau of Mines biennial survey. This represented an increase of 2.4 million gallons per day during the 2-year period since the last survey. In the previous 2-year period, capacity had increased 7.5 million gallons per day. The major increase in operating capacity occurred in Texas and New Mexico. In New Mexico, capacity increased 43 percent. The total number of plants decreased from 600 on January 1, 1956, to 584 on January 1, 1958. The number of operating plants decreased from 571 to 558. Five new plants were completed in Colorado, increasing the number of operating plants from 7 to 12.

Jan 1, 1958

During the initial portion of the contract several alternative designs were considered, as set out step by step in the monthly reports. The conclusions reached during this period were - to use on INTERDATA Model 70 as the system minicomputer - to drop the idea of multiplexing and digitizing the inclinometer outputs downhole due to the greater complexity and cost that that alternative would imply - to use a multitasking software monitor to enable synchronization of the several tasks that the system would have to perform simultaneously - to use a common controller for all I/0 devices except those which were available off the shelf from Interdata - to use a sheave counter to meter off equal increments of probe travel, but to supplement this information with the use of an encoder on the winch drum in order to be able to measure total probe travel unambiguously. - to place all I10 device interfaces in a bin connected to the common controller. During this period considerable attention was dedicated to the design of the mechanical components contemplated it the original contract. Of these, only those required for vertical probe was complete at the time that it was decided to forego the mechanical subsystem and concentrate on developing the necessary electronics and software to interface with the probes being developed by the Bureau of Mines.

Jan 1, 2012

By Alfred L. Ransome

GOLD output in Alaska in 1950, following a 2-year decline, increased to the highest point since 1942. Tills unexpected gain in production of the Territory's greatest value commodity was largely responsible for the increase in the over-all value of mineral output in the Territory to $17,852,000 from $15,549,000 in 1949. Although coal continued to rank second to gold in value of output, production was slightly less than the record production of 1949. The mining of platinum continued to be an important factor in the mineral industry, with production of crude platinum metals exceeding that of 1949. The output of lead was three times the 1949 production, and silver gained 46 percent over the previous year's total. Copper and zinc production-entirely as byproducts from other ores-showed an increase, but remained minor. Production of tin was relatively small, but substantially above the total for 1949.

Jan 1, 1953

By Robert W. McKibbin

The Bureau of Mines conducted laboratory tests to determine the slurry transport and deposition properties of coal waste. A 188.5-ft pipe test loop was constructed with instruments to measure density, flow, and power and discharge, suction, and differential pressures. A 20-ton ample of Western coal waste was crushed and screened to 100 pct minus 1/2 in. Eight loop tests using this graded waste were run at slurry densities ranging from 1.15 (25 wt-pct solids) to 1.46 (60 wt-pct sol-ids) 0 The resultant friction-'pressure gradients ranged from 0,06 to 0.24 ft of water per foot of 4-in standard steel pipe. Particle-size degradation was significant.. In a typical loop test lasting 25 min, the minus 200-mesh fraction increased from 19 pct to 34 pct. Deposition tests showed that without the use of a flocculant, the slurries would not dewater when left to stand for 1 week. With flocculant, additional water was releas2d; however, the settled slurries remained thixotropic. Further testing is necessary to determine their suitability for use as backfill material in active mines.

Jan 1, 1983

By H. H. Fields

The Bureau of Mines conducted research to determine the effectiveness of long holes drilled in solid virgin coal in degasifying an area of the Pittsburgh coalbed showing that horizontal holes drilled into a virgin coalbed from the bottom of any shaft will effectively remove methane gas in commercial quantities from the Pittsburgh coalbed. The in situ pressure at a depth of 214 feet into the coalbed and the average gas and water flows from the five degasification holes were 3 lb/in2 gage and 860,000 ft3/d and 1.7 gal/min, respectively. On June 19, 1975, after 593 days of degasification, a compressor was installed and pipeline quality gas was introduced into a commercial pipeline. As of June 1, 1976, after 1,022 days of degasification, over 753 million cubic feet of gas had been drained and 117 million cubic feet of gas had been purchased by the gas company for use in the local community of Wadestown, W. Va. The gas drained to date is six times the gas estimated to be in the area subtended by the holes. Methane emissions at the working face of 1 West mains, Federal No.2 mine has been reduced by 50 pct, proving the value of methane drainage by horizontal degasification holes drilled from shaft bottoms ahead of mining.

Jan 1, 1976

By Jane Applegate

This report documents efforts to design, develop and test a training approach which would assist front-end loader operators in the acquisition of skills and awareness to reduce the probability of their involvement in accidents in the mining environment. The goal of this project was to prepare and use (on a trial basis) a training method and materials which would be generally applicable to any loader and surface mining operation while at the same time, be adjustable by mine personnel to meet the specific needs of each mining operation. This effort resulted in the Front-End Loader Training System, a structured, performance-based training approach with diverse instructional aids and classroom and on-machine training experiences. Validation of the System at a large western mine demonstrated the utility and flexibility of the training approach and materials.

Jan 1, 1983

By L. B. Pankratz

Thermodynamic data on the elements, oxides, sulfides, halides, and selected hydrides, carbides, nitrides, carbonates, sulfates, silicates, and miscellaneous compounds were reviewed, evaluated, and compiled at the Bureau of Mines. Values for CP°, S°, H° -H°298, ?Hf°, and ?Gf° are given in tabular form. A brief thermodynamic background and a number of examples and applications are presented.

Jan 1, 1984

By Raja V. Ramani

The recognition that surface mining need not be viewed as a permanent dedication of the land but rather as a temporary non-renewable use in a series of land uses has caused greater emphasis on the re-use of surface-mined lands. In an effort to develop a procedure for evaluating postmining land use potentials, specific mines in various regions of the U.S. have been studied to determine the extent of current mined-land planning and to discover characteristics that are regional in nature. As part of this investigation, the Indian Head Mine, which is located in Mercer County, North Dakota, has been studied. The Indian Head Mine is presently operated by The North American Coal Corporation -Western Division and has been in operation since 1917 under various ownership. The status of current reclamation and postmining land use planning was reviewed. In addition, the relationship between mine planning and public planning in an area impacted by energy development was investigated. Finally, key factors affecting site potential realization for western surface mines have been identified.

Jan 1, 1983

By E. Robert Ruhlman

["Phosphate rock" is a broad term applied to natural deposits of minerals valued chiefly for their phosphorus content. More specifically, phosphate rock may be defined as a natural rock containing one or more phosphate minerals, usually calcium phosphate, of sufficient purity and in sufficient quantity to permit its use directly, or after beneficiation, in the manufacture of phosphorus-bearing products. The grade or quality of phosphate rock is expressed either in terms of its phosphorus oxide (P20S) content or the equivalent in tricalcium phosphate (Ca3(P04)2). The trade name for tricalcium phosphate is bone phosphate of lime (B. P. L.).]

Jan 1, 1958

By J. S. Stachulak, G. H. Schnakenberg

The objective of the Diesel Emissions Evaluation Program (DEEP)-sponsored project at Inco's Stobie mine was to conduct a long term field evaluation of diesel particulate filter (DPF) systems available to the underground mining industry. Some of the major issues studied were criteria for selecting the filter media, means of DPF regeneration, efficiency of DPF systems and the occurrence of unwanted secondary emissions, and reliability and durability of DPF systems. Nine state-of-the-art diesel particulate matter (DPM) filtration systems have been retrofitted to heavy-duty and light-duty vehicles and have been subjected to extensive long-term in-mine evaluation. Periodic efficiency tests were conducted at various stages of the study (2001, 2002 and 2004) to establish in-use efficiencies and durability of the tested DPF systems. The results were used to assess the effects of the filter systems on the concentrations of particulate matter, nitric oxide, nitrogen dioxide and carbon monoxide in the vehicle exhaust. The variety of filtration systems and regeneration concepts used in this study offered the opportunity to investigate their advantages and disadvantages. This paper also offers a review of selected experiences with the installation and operation of the DPF systems on underground mining vehicles at the Inco Stobie Mine.

By Walter W. Kaufman

This User's Manual, extracted from information contained in the Final Report for the above referenced project, outlines test procedures to measure the braking capabilities of underground non-coal rubber-tired mining equipment. Methods to interpret test results, recommendations for safe braking capabilities, and basic techniques to improve braking systems and road surfaces are also discussed. Possible applications for runaway vehicle protective devices other than braking systems are reviewed. Also included is a listing of mining equipment and brake component manufacturers who supply the majority of equipment to the United States non-coal mining industry. In conjunction with this list of manufacturers, a general tabulation of brake related specifications appears for vehicles observed during stopping tests conducted underground.

Jan 1, 1977

By J. Girard-Dwyer, T. Camm

Direct costs such as medical, legal, administrative, and worker’s compensation costs, property damage, lost earnings, and lost benefits are typically used to compute the economic impacts of occupational injuries. However, there are also a number of less obvious, indirect costs that substantially contribute to the overall loss costs. In fact, for every $1 of direct costs an estimated $3 to $5 of indirect costs are also incurred. This paper presents a systems approach that incorporates engineering, economics, psychology, and sociology in order to evaluate the total value of investments in safety. By studying the interrelated system comprised of the injured worker, their family and coworkers, as well as the organizational structure that was the setting for the incident, a methodology can be developed that will more accurately capture the true costs of mine injuries.

By J. H. East

"INTRODUCTION Diesel locomotives have been used successfully in underground mines of Europe for 18 years, and much has been written on the technical details of the design of these machines and the safeguards provided by the manufacturers. The actual conditions under which' the Diesel locomotives are used have not been publicized as well and consequently are not well-known. In 1945 the writer observed numerous Diesel locomotives working underground in coal and metal mines of several European countries and was favorably impressed with the practical approach to the safe use of this- type of equipment.Recent statistics showing the number of Diesel locomotives in use are not available now because of the World War, but the extent to which this type of mine locomotive was used immediately before the war is indicated by table 1, which classifies the number of locomotives used in several countries according to the type of power, such as compressed air, Diesel, and electric.Mining conditions observed by the writer in the European countries are very different from those in most coal-mining districts of the United States. The surface plants are larger and are permanently constructed of brick or concrete; numerous coal beds are worked through one shaft; the crosscut rock tunnels or levels, driven to intersect the coal beds, are lined with brick or concrete blocks where needed instead of timber; the coal beds dip more steeply and are not as thick as in most fields of the United States."

Sep 1, 1946