Search Documents

By W. R. Hardwick

This Information Circular describes copper mining and concentrating methods, practices, and costs at the Silver Bell Unit of American Smelting and Refining Co., Pima County, Ariz. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The Silver Bell mining district, one of the older districts in Arizona, is in the western part of the Silver Bell Mountains in Pima County, about 40 miles west of Tucson and about 20 miles southwest of Red Rock, a station on the main line railroad of the Southern Pacific Co. The Oxide and the El Tiro open-pit mines of the American Smelting and Refining Co. are in the district (fig. 1. The principal ore deposits are in T. 12S., R.8E., Gila and Salt River base line, at an altitude of about 3,000 feet. The present town of Silver Bell, established in 1952, is reached by a paved highway, the Avra Valley road, that turns west from Highway 84 at Plata siding near Rillito and extends westward 25 miles to the townsite (fig. 2). The present town is about 5 miles southeast of the old town of Silver Bell that flourished from 1900 to 1930.

Jan 1, 1963

By D. Harrington

Approximately 6,000 coal mines are operated in the United States. All of them have in some degree the elements that are likely to contribute to an explosion, hence it is surprising that explosion disasters are not more frequent and that many mines have been operated for years and finally worked out and abandoned without experiencing an explosion. The absence of coal-mine explosions does not always indicate that effective efforts have been made to prevent them but rather that the nine has been fortunate in that the combination of circumstances necessary to cause an explosion has not existed. In view of present knowledge of the methods of preventing explosions, disasters are inexcusable and discredit the mining industry. The methods of preventing mine explosions are known to experienced, well-informed persons engaged in coal mining, yet despite this knowledge far to many coal-mine operators continue to use practices and methods that they should know have resulted in numerous explosions. Moreover, many mine workers persist in following past procedure irrespective of consequences and in breaking safety rules or indulging in practices almost certain eventually to result in disaster. Continued failure to apply known common-sense methods of accident and explosion prevention unquestionably will cell for ultimate enforcement of law.

Jan 1, 1940

This report is a compilation of all information obtained in accordance with the requirements of contracts SO122076 and H0232056. A series of eight coal mines were visited to determine their communications usage and requirements. Presently available equipment was surveyed and evaluated to determine its applicability to the needs of the mines. The equipment studied includes that made by the following companies : Anaconda Telecommunications Division Andrew Antenna Bendix Communications Division Collins Radio Group of Rockwell International Executone Communication and Sound Systems Gau-tronics Mine Safety Appliances Company Motorola Communications and Electronics, Inc National Mine Service Company Plessey Communications Systems Corp Pye Electronics Limited Reach Electronics Set Com Corporation Sonex Incorporated Mine visits and in-depth interviews were made alt the following sites: Robena No. 4, Pennsylvania Greenwich Colliery Mines, Pennsylvania Somerset Coal Mine, Colorado Keystone No. 1, West Virginia Harris Mine No. 1, West Virginia Baldwin Underground No. 1 Mine, Illinois Lovilia No. 4 Coal Mine, Iowa Orient No. 3 Coal Mine, Illinois

Nov 15, 1974

By Robert R. Stein

Using an automated drill test fooure, the U.S. Bureau of Mines measured the sound power levels produced by a small, pneumatic, rotary roof drill. A series of tests was conducted to determine (1) the relative effectiveness of several drill muffling schemes and (2) the relationship between drill sound power and pneumatic power supplied to the drill. The influence of rotation rate (i.e., airflow) and feed thrust on the penetration rate of the drill was also noted.

Jan 1, 1989

By John C. Machisak

THIS INFORMATION CIRCULAR covers the calendar year 1055 and contains statistical data on employment and injuries pertinent to metal and nonmetal mining and to their mills and processing plants that are voluntarily reported annually to the Federal Bureau of Mmes. This report, unlike previous publications, lists not only production and development workers but also office employees associated with mining and milling or processing. The last publication m the series, Information Circular 7798, Injury Experience in the Metal and Nonmetal Industries, 1954, also contains unpublished injury and employment statistics for 1943 through 1953. The Bureau is authorized to request data on injuries and employment from operators in the metal- and nonmetal-mining industries. The information voluntarily submitted by these operators contributes immeasurably to the promotion of safety in the mineral mining industries as it discloses the hazards to which metal and nonmetal workers are continually exposed during mineral extractive operations.

Jan 1, 1959

By W. I. Nelson

This paper which describes the milling practice of the Engels Copper Mining Co., is one of a series on milling methods being prepared for and published by the United States Bureau of Mines. ACKNOWLEDGMENTS Acknowledgment is made of the assistance rendered by J. Casagrande, mill foreman of the Engels concentrator, in collecting much of the data presented in this paper.

Jan 1, 1932

By Lewis A. Smith

This circular presents a summary of the domestic chromium industry, and discusses the salient features of the world situation , reflecting the literature of the subject . The United States Bureau of Mines has in its files additional detailed information on many subjects briefly discussed in this paper and desires to assist the industries and the public by giving further data in response to individual inquiries . It will welcome comment and criticism and any contributions that would assist in making future editions of this circular more accurate . Unlike most common metals , chromium is rarely marketed as a pure metal . The chromium industry deals mainly with chromite , the principal ore of chromium , and with ferrochromium , the basic alloy in which chromium enters the metallurgical industry.

Apr 1, 1932

By A. Brown

This report details work performed and results obtained in a study of the water management aspects of oil shale mining and retorting in the Piceance Creek Basin. Three specific sites were investigated, and optimal water management systems for both conventional and in-situ extraction processes were generated. Water-related legal and environmental constraints on development were identified and the water management schemes were developed in compliance with these regulations. Limitations on shale oil production implied by limited water supplies were evaluated. Potential Basin-wide effects of development were evaluated using a computer model, and mitigation strategies were developed. Recommendations for additional investigation and analyses were presented.

Jan 1, 1977

By R. S. Warfield

The Kasna Creek copper deposit near Lake Kontrashibuna in the Lake Clark region, Alaska, was the object of an investigative project by the Bureau of Mines during the fall of 1948. Recessed because of inclement weather, it was completed in 1949. This project was a part of the Bureau of Mines program in Alaska for the development of critical and strategic minerals. The ore bodies are contact-replacement deposits in limestone. Mineralization is mainly specular and micaceous hematite associated with chalcopyrite, calcite, chlorite, quartz, and amphibole. The deposit, on the right limit of Kasna Creek approximately 2 miles from the shore of Lake Kontrashibuna, is composed of two mineralized zones that range in altitude from 2,350 to 2,650 feet. This report contains a brief history of the prospect, description of the physical setting of the property, its geology, and the factual results of the Work performed by the Bureau of Mines.

Jan 1, 1951

The Thermo-MIE personal DataRAM dust monitor (pDR) is a light-scattering instrument approved for use in gassy underground mines by the U.S. Mine Safety and Health Administration (MSHA). However, the use of light-scattering monitors has been inhibited by concerns about inaccurate readings resulting from changes in dust size distribution and composition, as well as concerns about the impact of moisture in the mine air. Because of this concern, the National Institute for Occupational Safety and Health (NIOSH) evaluated the pDR using available data from laboratory tests and mine surveys. The data show that accuracy can vary widely from test to test and mine to mine. In most cases, the results can be improved by using a companion gravimetric measurement to adjust the pDR data.

Jan 1, 2006

By Frank J. Perzak

This report describes a U.S. Bureau of Mines study on the hazards of large-scale conveyor belt fires in underground coal mines, as a function of both air velocity and distance from belt surface to gallery roof. The fire hazards considered were smoke obscuration, toxic effects of carbon monoxide (CO), and elevated air temperatures downstream of the fire. All of these hazards scale with the ratio of fire intensity to ventilation airflow. These hazards were all found to be greater at the lower belt-to-roof distance, owing to the greater fire intensities that resulted. The hazards of smoke obscuration and elevated CO levels were greater at lower air velocities. Smoke obscuration was found to be the earliest hazard, reaching critical levels before the stage of belt flame spread. Critical levels of CO and downstream air temperatures were not reached until the later stages of flame spread. Fire growth rates during rapid flame spread were much greater than rates measured during the early stages of belt burning. Data were analyzed to determine the early-warning capability of fire sensors. Smoke sensors provided the earliest warning, followed closely by CO sensors. Thermal sensors did not exhibit any early warning capability.

Jan 1, 2010

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,954 samples, representing the products of 93 companies. The samples were collected during December 1955, January and February 1956. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor Gasoline Survey reports published during the post 10 years is given on page 5.

Jan 1, 1956

By John H. Hild

This is a report on work done and results obtained in a minerals exploration program conducted by the Bureau of Mines on the lead-zinc deposits in the Ross Basin-Lake Como district, San Juan County, Colo., in 1948, 1949, and 1950. Four large veins--the Seven Thirty, Red Rogers, Cashier-Shorts top-Canandaigua, and Queen Anne--and several narrow spur veins were explored at relatively shallow depths with core-drill holes. Thirty-nine holes, totaling 10,491.5 feet, were drilled, and the core samples were assayed at the Bureau of Mines station at Salt Lake City, Utah.

Jan 1, 1959

By Jon C. Volkwein

In This Chapter [Instruments for measuring dust How to calculate the amount of dust from a source How to get a valid concentration measurement Sampling to assess control technology effectiveness] When there is more than one source of dust, sampling may be required to find which dust sources are most significant. Then, efforts to reduce dust can be concentrated where they will have the most impact. This chapter explains how to perform dust source sampling. It describes two kinds of instruments that are available and discusses their limitations. It explains how environmental variables such as concentration gradients, dust dilution, and production changes can impact dust measurements. It also suggests practical ways to improve the validity of dust source measurements under adverse conditions, such as high-velocity airflow or the presence of water mist in the air. [Dust source sampling at coal mine longwalls and at tunnels is more complicated. Chapters 3 and 7 have more information on sampling in those circumstances.] TWO KINDS OF INSTRUMENTS FOR MEASURING DUST Gravimetric samplers. The conventional gravimetric sampler is a good device for measuring dust because it is the instrument used for compliance measurements. This dust sampler consists of an air pump, a small cyclone that separates out the respirable size fraction of the dust cloud, and a filter to collect the respirable dust. In coal mines, the Mine Safety and Health Administration (MSHA)-approved gravimetric sampler uses a 10-mm Dorr-Oliver cyclone operating at an airflow of 2.0 L/min [30 CFR78 74 (2002)]. A correction factor of 1.38 is applied to make the results consistent with the U.K. MRE sampler, the instrument on which the 2.0 mg/m3 coal dust standard is based.

Jan 6, 2003

By Leonard Obert

Subsidence to surface occurs in a large proportion of underground mines. Preliminary to any indication of subsidence on the surface, there is usually a breaking up and sloughing of the cover into the mine opening which, in a period of time ranging from minutes to many years, progresses to the surface, This process is referred to as subsurface subsidence. In many mining operations, information regarding the process of subsurface subsidence is important, For example, if there are buildings or other improvements on the surface, or if the direction of the subsurface subsidence might threaten other underground workings--such as shafts--or if the subsidence might be progressing in a direction which would fall outside the anticipated subsidence limits, the problem could assume special significance.

Jan 1, 1961

By C. P. Bowie

For years many oil producers have believed that often low-pressure oil- and gas-bearing strata have been over coked in fields where the rotary system of drilling has been used. Collom3/ gave as a reason for this con¬dition that because the mud fluid was thick, the oil or gas stratum was plastered and sealed as the tools passed through it and no oil showed at the surface. Although this observation was made 15 years ago, it may often still be true notwithstanding modern developments in coring and electrical logging. Operators have believed, also, that mud fluid does not solidify behind the casing. Lewis and McMurray4/ stated: "All the evidence obtainable from practical experience points to the fact that the mud fluid properly mixed and employed does not solidify behind the casing, even in deer wells and after long periods."

Jan 1, 1937

By Scott W. Hazen, Richard F. Link, George S. Koch

The Mi Vida mine , Big Indian district , San Juan County , Utah , is in an ore deposit of uranium and vanadium minerals disseminated in certain sedimentary beds of the Triassic Chinle formation . Statistical analysis of assays of samples taken from the ore body affords an estimate of the grade of the ore body and provides a prediction about the direction of best mineralization beyond the sampled area . The basic data analyzed are assay results for uranium ( Uз Og ) , vanadium (V₂O ) , and lime (CaO ) from 225 channel samples cut at 79 sample points . Through the use of appropriate statistical methods , particularly regression analysis , the grade of ore may be estimated more precisely than by conventional means , and the most favorable direction to extend the mine may be predicted . Frequency distributions of assay residuals for uranium , vanadium , and lime are compared to frequency distributions of assays without regard to trend . Correlations among these variables are obtained and interpreted . The statistical methods employed illustrate certain techniques that may be used to analyze assay data from ore deposits in general .

Jan 1, 1964

This chapter describes the adverse health effects associated with exposure to respirable coal mine dust. Epidemiological studies of underground and surface coal miners in the United States and other countries are discussed. Also discussed are animal studies that add to our understanding of particle deposition and retention in the lungs and associated disease responses. This chapter emphasizes studies that (1) were performed since the passage of the Federal Coal Mine Health and Safety Act of 1969 [P.L. 91- 173], (2) used standardized methods of exposure monitoring and disease classification, and (3) investigated exposure-response relationships between respirable coal mine dust exposure and disease. Several published review articles contain further discussion of health effects studies of coal miners [Attfield and Wagner 1992b; Petsonk and Attfield 1994; Cotes and Steel 1987; Merchant et al. 1986; Morgan and Lapp 1976; Morgan 1975].

Jan 1, 1997

By Leo A. Schrider

This report analyzes the successful low-pressure gas drive in the Keener sand of the Bonds Creek oilfield, Pleasants and Ritchie Counties, W. Va.) and predicts its future performance. Core analysis from two wells and electrical and radioactivity logs were used to evaluate the reservoir characteristics. Production records over a 37-year period indicate that over 240,000 barrels of oil have been produced from the Keener sand by low-pressure gas injection. Decline-curve analysis shows that 165,000 additional barrels should be recovered from 108 acres of productive sand by continuing this secondary-recovery method.

Jan 1, 1966

By C. M. Harrer

This paper describes the location, features, qualities, extent, and potential of iron occurrences and some associative resources - limestone and dolomite, coal, petroleum and natural gas, power, and water - in New Mexico. Reconnaissance investigations were made of 118 iron occurrences to determine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential iron markets are discussed. The most abundant iron minerals are magnetite and hematite, The higher grade deposits are extensive contact-metamorphic and pyrometasomatic replacements in calcareous Paleozoic rocks associated with intrusives. Low-grade deposits of considerable potential are the extensive Cambrian oolitic hematites of sedimentary origin and the Precambrian magnetite-hematite taconite iron formation. Iron occurs also as extensive colluvial and alluvial concentrations. A wide variety of accessory elements are indicated and these pose metallurgical and economic problems.

Jan 1, 1963