Search Documents

By Herman W. Hill

This report summarizes research into the root causes of failures in mine power systems which impact safety and reliability. Abnormally low fault currents, due to arcing faults, self-excited systems, and fallen trolley wires are examined and quantified. The reliability of components which are critical for safety is studied, as well as reliability of components which are crucial to the mining pro cess. Failure rates are found through in-situ tests, accelerated life tests, studies of mine maintenance, and fault-tree analysis. Reliability data is used to predict fatalities and lost-time accidents through computer-aided fault-tree analysis. Analytical support tasks reported include the deriving of trailing-cable ampacities under cyclic loading, and the measurement of connected ground beds.

Jan 1, 1981

By Frank A. Peters

The Bayer process treating Jamaican bauxite was evaluated from an economic standpoint, using standard estimating methods and published data, to present a reference point for cost estimates for nonbauxite alumina processes. The estimated operating cost for a plant producing 1,000 tons of alumina a day is $47.96 per ton of alumina when charging $8 per ton for bauxite and $2.30 per hour for direct labor. The estimated fixed capital cost is $46 million.

Jan 1, 1966

By Wallace E. Anable

This investigation by the Bureau of Mines was conducted chiefly on Cuban serpentine nickeliferous ores to determine whether these materials would be amenable to direct carbothermic reduction in an electric furnace to produce a low-carbon ferro-nickel. The project was carried out as one of several under a Memorandum of Agreement between the Bureau of Mines and the General Services Administration (Contract GS-OO-B (D)-152l). Two ore samples were received for this investigation. One was a mixture of nickeliferous serpentine from the North Ocujal, South Ocujal, and San Juan claims of the Nicaro Nickel Co. The other sample was a mixture of material from the Ramona and the Lorna Mulo claims of the Cuban Nickel Co. Most of the ore from the Ocujal-San Juan deposits and about 40 percent of the sample from the Ramona-Lorna Mulo deposits were calcined before smelting. The remainder of the sample from the Ramona-Loma Mulo deposits was smelted after drying to about 8 percent moisture. An arc-resistance, selective-reduction smelting technique was employed in these tests. Either bagasse alone or a mixture of bagasse and coke was used for reductants. No flux was used in the furnace charges.

Jan 1, 1957

By Lester G. Morrell

While developments in Australia dominated the minerals industry of the South Pacific area, New Caledonia's nickel, manganese ore from New Hebrides, gold from Fiji and New Guinea, and phosphate rock from several small islands were significant in world supplies of those materials. The total value of mineral commodities produced in this area in 1965 has been estimated at about $763 million an increase of nearly 16 percent over the value reported in 1964. Increases were recorded in mineral production value with respect to that of 1964 for all of the countries except Papua-New Guinea where lower gold output resulted in a drop of about $300,000 and in the several phosphate-producing islands that collectively recorded a value decline of around $1.3 million. Exploration and development activities continued at an intensified level, not only in Australia and New Zealand but also in the British Solomons, Bougainville, and Fiji. Substantial additions to world supplies of iron ore and bauxite are assured and recent discoveries of natural gas, manganese ore, and nickel combine to give Australia a brilliant mineral outlook. Important discoveries of copper on Bougainville Island and on Vanua Levu, the north island of the Fiji group, and a gold mine on Misma Island were being developed during the year, with plans for early production underway. In New Zealand progress has been made on the New Zealand Steel Company project, and preliminary appraisal of a new titano-magnetite beach sand resource on the South Island has aroused considerable industrial interest. Extensive geophysical investigations were carried out in the British Solomon Islands and on Fiji's goldfields. The expansion program that will double output of products by New Caledonia's Société Le Nickel continued through 1965, and several foreign private companies have expressed a desire to initiate additional industries based on nickel prospects in New Caledonia.

Jan 1, 1967

By Robert K. Koch

The Bureau of Mines investigated separating HF from HF-SiF4-H2O mixtures by passing the mixed gases through a sodium fluoride slurry in an airlift scrubber and forming a mixed precipitate of NaHF2 and Na2SiF6. The oven-dried precipitate was thermally dissociated in two stages. The first stage was carried out at 400° C and dissociated NaHF2 to NaF and HF. Condensation and analysis of the evolved HF proved it to be 97 to 99 weight-percent HF containing 0.79 to 0.99 weight-percent H2O and 10 to 93 ppm silicon. The second stage was carried out at 700° C and dissociated Na2SiF6 to NaF (for recycle) and SiF4. The quantity of HF recovered from gaseous HF-H2O-air mixtures decreased with increasing relative H2O concentrations. Air was beneficial when scrubbing extremely dilute wet HF gases. At HF partial pressures of 0.24 and 0.013 mm Hg in the scrubber entrance gases, HF partial pressures of 6.2 x 10-4 and 9 x 10-6 mm Hg were obtained, respectively, in the scrubber exit gases. Scrubber efficiencies were 99.7 and 99.3 percent.

Jan 1, 1966

By E. G. Davis

Large-scale ultrafine grinding tests of a coarse kaolin were made using the Bureau of Mines developed attrition grinding process in continuous open-and closed-circuit systems. A 20-inch diameter attrition grinder, designed and constructed at the Tuscaloosa Laboratory, was used. Studies included single- and multiple-stage open-circuit grinding, and also continuous grinding tests in closed-circuit with a 6-inch-diameter solid bowl centrifuge. Clay feed, containing 9.0 percent minus-2-micrometer esd, was used at fates up to 840 pounds per hour. Multistage grinding tests gave better results than single-stage treatment when equivalent clay feed rates were used. Closed-circuit grinding tests yielded ground products containing slightly more minus-2-micrometer-esd clay than the open-circuit grinding when using the same clay feed. Energy consumption was lower in closed-circuit grinding than in batch or open-circuit grinding. A modified two-stage closed-circuit grinding system gave the best grade of product and amount of minus -2-micrometer-esd clay produced per pound of clay feed. The ground product from this test contained 88.5 percent minus-2-micrometer-esd material and electrical energy consumption was 327 kilowatt-hours per ton of minus-2-micrometer-esd material produced.

Jan 1, 1973

By Tilman M. M.

The effects of substituting cobalt for nickel on the acid corrosion resistance of two types of austenitic stainless steel were determined. Cobalt substitutions to a maximum 2.2 weight-percent were made in types 302 and 309 stainless steels. Total immersion corrosion tests were made in 10 volume-percent hydrochloric acid, and boiling-acid tests were conducted in 65 weight-percent nitric acid and in undiluted glacial acetic acid. For modified type 309 in acetic acid, corrosion rates decreased for additions greater than 0.57 weight-percent cobalt. Corrosion rates increased as cobalt was increased up to about 1 weight percent for modified type 302 in nitric and hydrochloric acids and for modified type 309 in nitric acid, but these rates decreased with a further increase in cobalt content. A gradual increase in corrosion rates with increasing cobalt content was shown for type 302 in acetic acid and for type 309 in hydrochloric acid. Cobalt substitutions in larger amounts (above a ratio of 8 Ni to 1 Co) may increase the corrosion resistance of the austenitic stainless steels.

Jan 1, 1965

By B. W. Jong

The Bureau of Mines studied reinforcement of sulfur concretes using glass, polyester, and aramid fibers. The objective of this research was to determine the feasibility of fiber-reinforcing the sulfur concrete to enhance the flexural properties. Optimum fiber sulfur concrete compositions were formulated with a cement-to-fiber ratio of 9.0:1 for glass-fiber and polyester-fiber sulfur concretes and 12.1:1 for aramid-fiber sulfur concretes. Test samples were prepared using techniques developed by the Bureau of Mines. Flexural strength values of up to 50 pct of compressive strength values were achieved with fiber additions. With non-fiber-reinforced sulfur concrete, the values ranged up to 20 pct. The impact strength and fracture toughness of sulfur concretes were increased sig-nificantly by reinforcement with glass or with aramid fiber and were adversely affected by use of polyester fiber. Strain tolerance was doubled and failure mode was shifted from catastrophic to noncatastrophic type by adding glass fiber. The glass-fiber and aramid-fiber sulfur concretes are resistant to acid corrosion and have proved durable in freeze-thaw cycles. This laboratory and field evaluation has shown that fiber reinforcement of sulfur concrete is feasible and that it enhances the flexural properties.

Jan 1, 1985

By Frank G. Horino

A rock mechanics program (composed of laboratory and field tests) was initiated by the Bureau of Mines in an effort to determine the causes of pillar instability at the Fletcher mine, near Bunker, Mo. Compressive strength, Young's modulus, shear strength, and the angle and coefficient of internal friction were determined on drill cores obtained from 16 different locations in the mine. Results of the laboratory tests showed that highly mineralized zones and brecciated zones in pillars could significantly affect pillar strengths and stability in locations where extraction ratios exceeded the normal design ratio of approximately 78%. High-angle fractures that were present in Some locations also may have contributed to pillar deterioration. In the field tests, in situ stress determinations were made in one pillar to establish the pillar-loading conditions and to evaluate the stability of the pillar. Continued monitoring of stresses in the pillar showed a gradual decrease in compressive stress, indicating that the pillar was probably in the postfailure state. A second stress determination was made in a vertical hole in the underlying igneous rock that was exposed on one section of the mine. Horizontal stresses were compressive and larger than would be expected from gravity loading.

Jan 1, 1978

By P. J. McDonough

The Bureau of Mines designed and tested a hardware-software system for measuring on-line corrosion rates of materials in a rod mill in operation. Currents ranging from 10-6 to 10-3 A and potentials in I-mV increments were converted to a digital signal. The digitized data were frequency-modulated and transmitted from a rotating ball mill to an FM receiver, where they were decoded by computer and then processed in real time using assembly language software. This design approach would allow accurate measurement and control of systems where signals of small amplitude and large ranges are present.

Jan 1, 1988

By G. D. Coe

Float-and-sink tests indicate what results are obtainable by gravity separation and rare therefore an invaluable adjunct to most coal-cleaning processes. However, it is difficult to make a direct interpretation of float-and-sink data on coal, and several systems for interpreting them have been proposed. Of these, that developed and used extensively by Bird3/, Yancey4/, and Gandrud5/ is considered by the author to be the most satisfactory. It makes use of four interrelated curves (hereafter referred to as be "washability curves"). These curves were explained by Bird in a paper6/ published in 1923, but his explanation has been regarded by some as not sufficiently

Jan 1, 1938

By M. G. Zabetakis

Benzene and toluene are the first two members of an important homologous series whose general formula is CnH2n-6. The members of this series differ in composition from benzene by some integral multiple of CH2; they can all be prepared in the laboratory by the Wurtz-Fittig, Friedel-Crafts and Grignard syntheses. Because 'of the industrial importance of these-hydrocarbons, the limits of flammability of eight members of the series have been determined at 100° C.-(A temperature of 1000 C. was chosen because the determination of the upper limit of flammability of p-cymene requires an apparatus temperature. of at least 90° C. As elevated temperature data are available for other combustibles at 100° C. but not at 90° C., all data were taken at 100° C. in order to obtain comparable results.) Minimum ignition temperatures of these combustibles have been determined at laboratory-pressures.

Jan 1, 1951

By Robert J. Hundhausen

During the early part of World War II , it appeared likely that supplies of chromite for United States industry might become critically short . As a part of the ensuing search for new sources of domestic chromite supply , the chromite - bearing black sands along the coast of southern Oregon were hurriedly investigated by State and federal agencies and by private interests , These investigations led to a decision to begin exploitation of the deposits immediately . A government stock- piling program was put into effect , a concentrator was financed by the Defense Plant Corporation , two privately controlled companies were encouraged to start mining operations , and the Bureau of Mines and the Geological Survey were authorized to search. for additional reserves of minable ore .

Feb 1, 1947

By Frank L. Hess

In the first cart of that little space of time that we have designated as the nineteenth century, chemistry had reached a wonderful stride. Viewed from the present heights attained by the efforts of innumerable chemists with perfected apparatus, mire reagents, air under pressure, water, gas, and electricity conducted to the desk, and. numberless other helps, it seems marvelous that chemists of that day obtained such results. In 1820, about half of the elements had. been discovered; of these discoveries, Swedes had made 15 or more, about once-third of the elements then known and nearly half of those discovered after 1700.

Jan 1, 1939

By L. P. Purtell

The performance of ten anemometers of several types has been measured at low air speeds. Multiple calibration runs provided sufficient data for measuring random error about the mean calibration curve in addition to the difference between indicated and true speeds. Measurements were also performed of the minimum operating speeds of the anemometers.

Jan 1, 1979

By A. M. Evans

"INTRODUCTION Exploration of the Iron Mountain and Bader iron-ore deposits in Llano County and the Gamble deposit in Mason County, Texas, was begun by the Bureau of Mines in January and completed in May 1944. The deposits had been examined by A. B. Needham, district engineer of the Bureau, in November 1942. Detailed geophysical studies by the gravity method as well as with a dip needle were made by the Bureau of Economic Geology 3/ of the University of Texas and the Federal Geological Survey. 4/ACKNOWLEDGMENTSIn the program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy., It is the policy of the Bureau to publish the facts developed by each exploration project as soon as practicable after its completion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Apr 1, 1947

By Roy E. Peterson

The Bureau of Mines has been developing and evaluating methods for beneficiating the large deposits of nonmagnetic (oxidized) taconite located on the western Mesabi Range. In this segment of the research, a sample representing about 0.5 billion tons of nonmagnetic taconite from near Grand Rapids, Minn., was beneficiated using a reduction roasting, magnetic separation, flotation process. The sample contained 32.1 pct iron and 49.1 pct silica. Tests were conducted both on a bench scale and with a 1,000-lb/h pilot plant. In the bench-scale research a con-centrate containing 69.0 pct iron and 4.5 pct silica was produced with an iron recovery of 82.1 pct. In the pilot plant, reduction roasting was conducted in a 35-ft kiln using lignite as the reductant and major source of fuel. Dust from the kiln exhaust was pelletized and recycled to the kiln. The roasted taconite was beneficiated by magnetic sep-aration and flotation to produce a product containing 67.9 pct iron, 5.5 pct silica, and 69.7 pct of the iron in the kiln feed. The cyclone separation in the grinding circuit was sharpened by demagnetizing the cyclone feed in a 400-Hz, 1,000-Oe magnetic field.

Jan 1, 1983

By James Westfield

A brief résumé follows of recent activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority (under Executive Order 9728) was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1958

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 3/16-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

By R. A. Bloomfield

This report summarizes Bureau of Mines contract research on the disposal of retorted oil shale. A data base has been developed describing the physical-chemical properties, geotechnical engineering properties, and natural cementation characteristics of spent shale. Results of field compaction tests and seepage pond tests are presented, along with results of a partially saturated finite element seepage model used to predict infiltration and seepage rates. Preliminary engineering analyses are presented for underground disposal systems, which include material transport methods, and for a surface disposal system, which includes stability analyses.

Jan 1, 1981