Search Documents

By Edward D. Thimons

The Bureau of Mines developed a stopping design that allows the stopping to be blown down by strong blast forces without incurring any permanent damage. Trials with the new stopping, dubbed the quick-fix blowout stopping, have been conducted in the Bureau's Safety Research Coal Mine at Bruceton, Pa., and in two New Mexico uranium mines. Results have been favorable in all cases. Compared with conventional brattice stoppings or wood bulkheads, the quick-fix blowout stopping is easier and less time consuming to install, is easier to maintain, and in most cases is just as efficient an air barrier. There is same indication that the shape of the stopping makes it more resistant to blast fore s than the fabric stoppings now in use.

Jan 1, 1976

By W. T. Millar

Field reconnaissance and laboratory tests an clay from South Windsor, Hartford County, Conn., indicate that the clay is suitable for lightweight aggregate raw material. Exploration of the deposit supports the conclusion that the reserves of clay are sufficient for economical mining operations to produce lightweight aggregate. Preliminary tests indicated that the clay has a short bloating range. Initial expansion occurred at 2,000° F, and at 2,100° F the clay was slightly overfired and sticky. Rotary kiln tests verified the preliminary data, and these tests showed that the clay would make a good lightweight aggregate if the processing temperature and the kiln feed sizes were closely controlled. Lightweight concrete made from the processed aggregate had properties comparable to those of concrete made from a commercial clay aggregate.

Jan 1, 1964

By R. J. Leary

The natural gas-air burner described in this report was designed and constructed to meet the thermal requirements of a convective process for heating steel scrap. This process involved downward combustion of natural gas with air, blending the combustion products with diluent air, and then passing this tempered stream of gases downward through a porous bed of steel scrap contained in the furnace chamber. The scrap would be heated to a temperature limited by the adiabatic flame temperature of the gas stream in a period that depended on the rate at which heat was supplied per unit of bed cross section. The temperature of the gas stream would be limited to that beyond which an objectionable degree of oxidation would occur; for carbon steel this limit had been found to vary from 1,900° to 2,100° F. with the superficial velocity of the gas stream. The productivity of the process was dependent on the rate of heat input per unit of furnace cross section; for the 3-foot-diameter experimental furnace an input of 680,000 B.t.u. per hour was desired. The burner described was designed to meet these conditions of temperature and heat input. It provided for three streams of entering gases: (1) A primary air-fuel mixture too rich to be combustible, that is, above the upper flammable limit; (2) secondary air for combustion of the primary mixture; and (3) tertiary air, principally for cooling the combustion products to the temperatures desired for process operation. Downward combustion of the primary and secondary streams occurred in a flame stabilized on an annular port, while tertiary air flowed in an annular path surrounding the port and also through an axial channel whose wall formed the inner ring of the annular port. This burner performed beyond the designed heat-input rates while producing stable flames, which were adjusted readily to the temperatures desired. Gas-stream temperatures were easily controlled to within 15° F. of the desired value by simple manual adjustment of the flow valves.

Jan 1, 1959

By W. M. Weigel

"Sand is one of the most useful and, fortunately, one of the most common mineral commodities. By far the largest proportion of the production is used in construction, including all forms of building, concrete and paving, sand for this purpose is produced in every State in appreciable amounts. Excluding send used for railroad ballast, molding sand stands not in tonnage produced, followed by glass sand.Special sands. In addition to the above, many grades of sands, with special characteristics, are used in industrial processes, and may be classed in a group as ""special sends"". This includes filter sand, sand blast sand, engine sand, abrasive send, fire or furnace send, special flooring sand, roofing sand used as a finish for prepared roofings and pottery placing sand sand blast and filter sand have been discussed in previous reports.Very few send companies depend upon the production of any one of these grades, as their source of revenue. They are generally especially prepared from the bank run of sand by different methods of screening or washing, or may, in some instances, be by-products from the production of ether grades. Many companies not now producing them might be able to supply local demands by a slight addition to their plant. In nearly all cases, they command a better price than the usual grades of building sand.Definitions and Properties.Engine sand, or traction sand, as it is sometimes called, is used to prevent the slipping of the driving wheels of locomotives, or other self-propelled vehicles, on wet or slippery rails. Its greatest use is, of course, for railroad locomotives, but street cars use considerable amounts and mine locomotives require its use. As the send must be very dry when used, most consumers have their can drying equipment, so it is often shipped damp, with its natural water content on what resulting from washing by the producer."

Oct 1, 1924

By Herman W. Sheffer

This report describes and discusses present-day leaching technology employed to recover copper from low-grade mine and dump materials derived from the exploitation of copper ore deposits in the Western United States. Illustrations of the integral parts of the leaching, precipitation, and recovery operations at several copper-producing companies are presented. Schematic drawings are included to present typical flowsheets of leaching and precipitation operations. Operational problems common to most copper leaching and precipitation plants are discussed. Areas of present and future research to improve leaching techniques are cited.

Jan 1, 1968

By John P. Gooch

The solubility of 1,1,2,2-tetrabromoethane (TBE) in water was determined from 1.0° to 97.0° C. The solubility (S) of TBE in grams of solute per 100 grams water was correlated with [S = 1,920.55 [exp (40292L7 11, T2 10 T 737.577 + 9.923962 ] where T is in degrees Kelvin. A thermodynamic analysis conducted on a system consisting of a TBE phase and a water phase in equilibrium with a vapor phase led to the calculation of the activity coefficient, vapor-liquid equilibrium distribution coefficient, relative volatility, and heat of mixing for saturated solutions of TBE in water. Data required for these calculations were the solubility of TBE in water and the vapor pressures of TBE and water as a function of temperature.

Jan 1, 1972

By W. Miola, R. V. Ramaoi

"The MSHA prescribed method for the determination of quartz in airborne respirable-dust samples from underground coal mines is the P-7 method, a combination of /ow-temperature, radio-frequency ashing (LTA) and infra7 red analysis (IR). There is no prescribed procedure for quartz analysis in bulk samples of coal and host rock. Dispersive infrared (IR), Fourier-transform infrared (FTIR) and X-ray diffraction (XRD) methods are most commonly used for the analysis of quartz in powders. Several aspects of the experimental procedures, such as the preparation of the analysis sample from bulk samples, ashing techniques, scanning procedures, peak measurement location, calibration techniques, sample amounts, size consist and data interpretation, affect the results from each of the methods differently. Significant differences in analytical results obtained from X-ray diffraction (XRD) and infrared spectroscopy (IR) on the same samples are reported. All studies point to the need for reliable quartz analysis methods.In a recent research program, a procedure for preparing bulk-coal and host-rock samples for quantitative quartz analysis was developed. Further, the results from X-ray diffractometry and infrared spectroscopy for quartz content on identical samples were compared. Calibrations with pure and mixed standards were used to assess the influence of particle-size distribution, matrix and calibration on the analytical results. In this paper, several issues concerning the measurement of quartz in the samples of coal, host-rock and airborne respirable dust from mines are outlined and quantified. IntroductionThe literature on coal-mine airborne-dust control has identified a need for a better understanding of the sources, mechanisms and amounts of quartz in mine airborne respirable dust (Althouse, 1984; Jankowski, Nesbit and Kissel, 1985; Ramani 1988; Qin, 1988; Bhaskar and Xu, 1990; Bhaskar and Li, 1992; Ramani, Qin and Miola, 1991 ). To understand the quartz content in the source materials, bulk samples of coal and host rock must be analyzed. Establishing an analysis procedure for determining the quartz content in bulk-coal and host-rock samples is necessary for identifying the sources of quartz in mines; for establishing the relationships between the quartz contained in the source and in the airborne dust; and for controlling the content of quartz in the mined product and in the airborne respirable dust."

Dec 1, 1996

By Raymond G. Travis

This report describes coal-mining methods, power requirements, coal production and distribution, and coal resources of the Bull Mountain coal field in Musselshell and Yellowstone Counties, south-central Montana Investigations in the field, were conducted by Bureau of Mines engineers The report contains a short summary of the geology and geography of the field and discusses the following information secured during the field study: Method of mining practiced at each mine, including a description of each phase of the mining cycle. Coal produced and its distribution at each mine. Power requirements and the consumption of electricity per ton of coal produced by mines. Number of non employed by mines, and the production per man per shift underground and the over-all production per man employed. Estimates of future production and power requirements for the field as a whole. This information should be of benefit to any company or individual planning the development of now coal mines in the area or the expansion of present operations.

Jan 1, 1950

By J. E. Schiller

The Bureau of Mines is investigating methods to treat waste water that contains cyanide. This report describes a new method that removes heavy metals and all forms of cyanide. In the first step, hydrogen peroxide and sodium thiosulfate are added at pH 7 to 9 in a 1:2 molar ratio to convert free and weakly complexed cyanide to nontoxic thiocyanate. Then steryldimethylbenzylammonium chloride is added to precipitate ferro-cyanide, and finally, ferric sulfate is added as a sweep floc and sequestrant for heavy metals. After the suspended solids settle, the water is polished by filtering. The water initially contained 1 to 5 mg/L Fe, 1 to 5 mg/L Cu, and 10 to 30 mg/L total cyanide; the level of each of these constituents was reduced to less than 0.02 mg/L.

Jan 1, 1983

By Jr. Kauffman

The data contained in this report were obtained incidental to the Bureau of Mine's investigation of the lime-soda sinter process as applied to the recovery of alumina from siliceous bauxite, kaolin, and other high aluminous materials. The Bureau of Mines was charged by Congress to investigate processes for the production of aluminum from domestic low-grade ores. The Eastern Experiment Station at College Park, Md., conducted laboratory and pilot-plant investigations of the recover-y of alumina by the lime-soda sinter process. Reports by the College Park staff covering the recovery of alumina from these sources have been published. The lime-soda sinter process involves the sintering of the finely ground siliceous bauxite or clay with limestone and soda ash in a rotary kiln. During the sintering the alumina supposedly reacts with the soda ash to form soluble sodium aluminate and the silica combines with the lime to form the insoluble orthosilicate. In the early stages of the investigation it was considered desirable to know the temperatures at which the phase changes occurred during the sintering operation. The total time involved in the passage of any given portion of the charge through the kiln was 28 minutes. The exposure time of the charge to temperatures above 600° C. (decomposition temperature of kaolinite) was, roughly, half the total. The exposure to the full temperature of the kiln, 1,100° C was only 3 minutes. (Subsequently, the maximum kiln temperature and retention time were increased.)

Jan 1, 1949

By Herbert R. Babitzke

The purpose of this investigation was to optimize the high-temperature properties of columbium and tantalum. Columbium and tantalum were combined with selected alloying elements to achieve solid solution and dispersion strengthening. Fifty-six alloys were evaluated to determine their formability, hardness, strength at elevated temperatures, and oxidation resistance. The following six alloys showed high-temperature strength: [Cb-15Hf-5W-2Zr-4Al-4Ti-2N Cb-15Hf -5W-5Zr Cb-15.3Ti-4.1Zr-13.7Hf Ta-20Hf-4Al Ta-30Hf-4Al Ta-20Hf-5W-4Al] At 1,200° C, the columbium alloys had strength values of 40,000 psi or greater, and the tantalum alloys had strength values from 50,000 to 58,000 psi. For a 2-hour test period at 1,000° C, weight gains of only 9 and 8 mg/cm2, respectively, were observed on oxidation testing of two alloys, Cb-15Hf-5W-2Zr-4Al-4Ti-2N and Ta-20Hf-5W-4Al.

Jan 1, 1968

By D. A. Reynolds, A. C. Fieldner, S. H. Katz

"03-01-192403-31-2019RI 2591 - Reports of Investigations - Department of the Interior - Bureau of MinesBureau of MinesPittsburgh Experiment Station American Society of Heating and Ventilating EngineersU.S. Public Health ServicesTucson Experiment Station Introduction.""Carbon monoxide self-rescuers,"" or simply ""self-rescuers,"" are pocketsize gas respirators which protect the wearer from air contaminated with poisonous carbon monoxide gas. On March 6, 1924, the Bureau of Mines approved the ""M.S.A. self-rescuer’ manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa., after the M.S.A- self-rescuer bad passed all the tests and requirements of the Bureau's Schedule 14A4.The purpose of the self-rescuer is to help miners to escape from mines in which fires are burning or explosions have occurred, by providing protection from carbon monoxide for at least one half-hour. The self-rescuer can be used similarly by workers above ground who may through accident become surrounded or entrapped by atmospheres containing carbon monoxide.no hazards threaten the miner, who escapes serious injury by fire or violence in a large mine fire namely, ( 1) asphyxiation by poisonous carbon monoxide gas; and (2) suffocation by insufficient oxygen to support life. In order to save himself, the miner must either erect a barrica4e5 against afterdamp and wait restoration of ventilation and rescue or take a long chance at getting out of the mine through entries not permeated by afterdamp.. The self-rescuer removes the hazard of carbon monoxide poisoning for one half-hour or more, and accordingly greatly increases the miner's chance of saving his life.This paper describes the construction and details of the M.S.A. self-rescuer as approved by the Bureau of Mines, and discusses its performance under test condition"

Mar 1, 1924

By Clyde E. Williams

The Northwest experiment station of the Federal Bureau of Mines , at Seattle , Wash . , was established in December , 1916 , and is one of 13 mining experiment stations maintained by Act of Congress , under the direction of the bureau , in the various sections of the country . Under the terms of the organic Act (March 3 , 1915 ) , the province and duty of these experiment stations is to cake investigations and disseminate information with a view to decreasing waste and improving the efficiency in the production , treatment , and utilization of mineral substances . The investigations carried on at the Northwest experiment station attempt to cover the needs of the mineral industry of the States of the Pacific Northwest and of the coastal regions of Alaska . The most in ortant needs of this district are for work on coal washing , electrometallurgy , and ceramics . The electrometallurgical investigations are not necessarily limited to the Problems of the Northwest , but may be of general application . Problems other than those specified above are referred to other stations of the Bureau that specialize on the particular type of investigation required . The Northwest station closely cooperates with the State of Washington through the University of Washington and with the State of Oregon through the Oregon Bureau of Mines and Geology . The University of Washington at Seattle has donated the use of an entire building , which houses the station's administrative offices and chemical laboratory , and parts of two other buildings which are usea in conducting the experimental avestigations . Twenty-five thousand dollars is expended annually by the Federal Government , while the State of Washington each biennium appropriates $ 20,000 , and the State of Oregon from time to time appropriates various amounts for the conduct of work along cooperative lines . Also , the station cooperates with private organizations tht have problems similar to those in which the station is interested . For example , the Washington Electrochemical Co. is cooperating in the electrometallurgical research, and furnishes part of the supplies and technical assistance required .

Mar 1, 1922

By W. H. Oppelt

Converting small-particle lignite to a stable, storable fuel of relatively high heating value was investigated. The fuel was prepared by thermal pretreatment of the lignite in an 8-inch i. d. rotary-drum retort, then the pretreated material was pelletized in an experimental 15-inch-i. d. rotary-drum pelletizer. Pelletizing tests were made with both starch and bituminous binders. During the first phase of the project, the quantity, composition, and heating value of products from the thermal processing of Kincaid lignite from Burke County, N. Dak., in an B-inch i. d. rotary-drum retort were investigated at a series of temperatures from 250° to 950° F. to establish optimum conditions for preparing feed material for pelletizing. To determine the response to thermal treatment of different lignites, 5 other lignites from Divide, McLean, Mercer, and Stark Counties, N. Dak., and 1 lignite from Saskatchewan, Canada, were processed at 700° F.

Jan 1, 1958

By Susan E. Brink

The first step in determining whether Mn can be recovered by in situ leaching is to develop and test a selective lixiviant. Two column leach tests and one core leach test Were conducted by the U.S. Bureau of Mines on Mn oxide ore using aqueous sulfur dioxide (SO2) as the lixiviant. The column tests showed that aqueous S02 could selectively dissolve available Mn oxides from calcite-rich ore in a heap leach system. However, the core test showed that calcite gangue side reactions can have pronounced negative effects on the likelihood of successful in situ leaching of a calcite-rich ore with aqueous S02. Petrographic and geochemical analyses showed that both Mn (IV, III) oxides and calcite were dissolved. The abundance of dissolved Ca caused precipitation of gypsum. Acid consumption by calcite dissolution caused a rise in pH that caused the SO/S species to shift to S032-(sulfIte), which hindered reductive dissolution of Mn oxide. Gypsum precipitation did not affect complete leaching of the rock fragments in the column tests; however, it plugged the natural permeability in the core. Manganese recoveries were high for the column tests and low for the core test.

Jan 1, 2010

By G. Asai

The purpose of this Bureau of Mines investigation was to determine the properties of arc-melted iron-chromium alloys ranging in chromium content from 12 to 50 wt.-pct. Alloys were prepared by consumable-electrode arc melting of electrodes composed of high-purity chromium and high-purity iron. Alloys were fabricated to rod and sheet, and the following data were obtained: Electrical resistivity, hardness, tensile strength, and impact strength at room temperature; and creep-rupture life at 650° C. (1,200° F.). As the chromium content of the annealed alloys varied from 12 to 50 pct., the properties varied as follows: The electrical resistivity increased proportionally from 41 to 53 microhm-cm,; the Rockwell hardness varied from A 38 to A 58; the tensile strength ranged from 52,000 to 96,000 p.s.i.; the impact strength of V-notched charpy specimens varied from 140 to 405 ft.-lb., and the 100-hour creep rupture life at 1,200° F. varied from 5,000 to 16,000 p.s.i.

Jan 1, 1962

By R. August Heindl

[A proposes process for recovering manganese from open-hearth steel-plant slogs is indicated by the flow diagram shown in figure 1. Investigation of the process, the laboratory development of which was reported previously,4/ was expanded to a larger scale. Mixtures of flush slags and limestone were proportioned to have molar [SiO2] ratios of 1.5 to 2.2 and were fired at temperatures up to 2,400° F. In an oxidizing atmosphere. This produced clinker consisting principally me various combinations of the oxides of manganese, iron, aluminum, and magnesium aloe with a dicalcium silicate phase containing the phosphorus. Some tests were made with a continuous sintering machine of the traveling-grate type, but a rotary kiln was the most satisfactory apparatus for this operation. Material was fed at 150 to 200 pounds per hour after first being agglomerated either on the sintering or else binder extruding and drying finely ground mixture of the sing, limestone, binder, and water. Tests with slag; from tree different source indicated overkill manganese recoveries of 65 to 80 percent by ammoniacal-ammonium-carbonate leaching.]

Jan 1, 1955

By H. W. GILLETr, E. L. Mack

The production of small heats of alloy steels on an experimental scale is often desirable in beginning the study of new alloy steels before large amounts of expensive alloys are used in heats of commercial size. Such small heats can sometimes be made up at crucible-steel plants, but few crucible-steel makers care to undertake experimental heats for other firms. Small electric furnaces offer some advantages over crucible furnaces for experimental work. Hansen1 in 1909 described a small 100-kilowatt single-phase, direct- arc furnace with a capacity of 50 to 300 pounds of steel, and such furnaces, of 200 pounds capacity or larger, are being successfully used by various firms for experimental work. They have the advan- tage of using the same metallurgical procedure as is used in prac- tice for larger electric furnaces. The very small sizes have the draw- back of lack of precision in controlling the carbon content of the steel. Small Rennerfelt two-phase, indirect-arc furnaces of 40 to 60 kilo- watts and small Industrial Electric Furnace Co. furnaces, single- phase with one electrode embedded in the hearth, of 25 to 50 kilo- watts, are also in use by a few firms for experimental work or for production on a very small scale. Hoskins carbon-plate resistor crucible furnaces are also sometimes used. Little seems to have been published on the use of these furnaces in making experimental alloy steels. Keeney' has given data on the making of uranium steels in a tilting Siemens furnace of 25 pounds capacity, and has described a small stationary Siemens furnace.

Jan 1, 1922

By Will H. Coghill, Fred D. DeVaney

"INTRODUCTION The Mesabi iron district of Minnesota has a potential production of over 50 million tons of iron ore annually. The large shipments of ore each year are gradually depleting the reserves, and if the present rate of production is to be maintained there must be a growth in the present available ore supply.Growth is a natural course. The growth of a city may be affected by the addition of city blocks or by the improvement of utilities necessary for its betterment, these may go on in the order named or concurrently. The city-block type of growth of the Mesabi has been tremendous, and the ""betterment"" type has followed in due course. Probably the former has reached its limit, and if so, more time will be allotted to the latter. It is not the intent of this paper to present either a eulogy of the wonderful mining methods or a history of the milling, but it is pertinent to say that if the lean-ore area continues to produce, the continuance will be more the result of further improvement of milling methods now well under way than of extension of boundaries by the city block plan of growth.In an examination of the western end of the Mesabi district one finds sludge basins containing millions of tons of millable ore rejected by washing plants which were built for economy in operating cost and with little thought of conservation, and rich tailings piles of jigging plant rejects. In addition, there is an appreciable tonnage of bawl rake pro-ducts so low-grade that it requires mixing with the best ore of the district to make it merchantable.Any of these three products is a source of additional reserves, but gangue must be removed before the products will comply with blast-furnace stipulations. All investigators are agreed that to effect this separation comminution must be fine enough for liberation, but beyond this point opinions diverge; some would seek new processes, while others adhere to methods and machines developed in other mining districts.In the investigation by the Mississippi Valley Experiment Station of the United States Bureau of Mines working in conjunction with the Missouri School of Mines and Metallurgy,Rolla, Mo., the latter course has been followed. Attention was first given to the sludge basins mentioned. From their contents good grades of concentrates were made and the results published 4 later commercial-scale tests were made in a pilot plant of 10 tables, and the laboratory results were confirmed, The tailings from jigging plants are high in iron, and a study of their possible retreatment showed that if they are recrushed, high recoveries of acceptable grade may be expected. The results will be published later."

Apr 1, 1932

By Paul R. Coyle, Anthony T. Iannacchione

A close look at the Loyalhanna Limestone of southwestern Pennsylvania reveals a complex structural environment. Most exposures of the Loyalhanna occur along Chestnut Ridge and LaurelHill within the Allegheny Mountain Section of the Appalachian Plateaus Province. Because the Loyalhanna is rated as a super-pavement aggregate by the Pennsylvania Department of Transportation and because of its proximity to the population centers of southwestern Pennsylvania, the Loyalhanna has been extensively mined along these prominent anticlinal structures. Geologic and engineering analyses were performed using gas well and core logs, outcrop examinations, underground observations, and mine maps. Strata exposures from both outcrops and quarries were used to construct geologic maps, stereo net, and rose diagram projections so that the Loyalhanna’s structural environment could be understood better. Many of these structural conditions cause ground control problems at local quarries. These problems ranged from small-to-moderate sized rock falls associated with roof jointing to pillar failures associated with dipping discontinuities. Stresses ranged from tensional on structural domes where weathering dominates, to high levels of compression within structural saddles. A greater understanding of these characteristics is a prerequisite to develop engineering controls, such as improved mine layouts, pillar sizes, etc., that lessen miner exposure to these hazards.