Search Documents

Careful monitoring of the position of the cave front is essential for well-managed block cave mining. Seismic monitoring systems yield 3-D information about the location of fracturing ahead of the cave. However, because the a seismic gap between cave surface and seismogenic zone is of unknown extent, the cluster of micro-seismicity can only yield an upper bound for the cave height. The large velocity contrast between the fractured rock in the aseismic gap and the broken loose material within the cave can be used by an inversion procedure to find a few simple geometric parameters (such as height of the top of the cave) if a simple 3-D shape?for example a paraboloid?is assumed for the cave. Ray-tracing must be used as the large velocity contrasts cause seismic waves to bend around the cave, but the inversion takes the form of a minimization problem in only a few dimensions and so the computational time is feasible. This technique has been successfully tested on realistic synthetic data.

Jan 1, 2007

By A. C. Mulholland

The electrical control of three-electrode submerged-arc furnaces suffers from a number of complexities, mostly due to the nature of the furnace electrical circuit providing power to the furnace where the three electrodes are interconnected within the furnace through the molten metal bath. This gives rise to what is known as the interaction effect 2, where variations in one electrode?s current can cause comparable changes to the currents in the other electrodes, particularly in larger furnaces with low power factor. Resistance-based control of the electrode penetration has largely alleviated these problems, since the resistance encountered by each electrode is predominantly dictated by the length and conductivity of the current path from the electrode?s tip to the molten metal bath, which acts as the three-phase circuit?s floating neutral point. Hence resistance changes due to tip position or conductivity changes beneath one electrode do not affect the resistances beneath the others, effectively decoupling the control of the individual electrodes1. Although resistance-based control is therefore generally accepted as superior to current-based control for the regulation of submerged-arc furnace electrode penetration, a few furnace operators still prefer to use current control under specific furnace conditions. This paper presents the results of analysing the performance of both current and resistance-based control in typical scenarios encountered on industrial furnaces, taking into account a number of factors including electrode penetration, power distribution, efficiency and asymmetry of the electrode currents. In order to accomplish this, three typically encountered scenarios were simulated. The results obtained show that resistance control provides more benefit in all cases, however, the uneven electrode current distribution generated by resistance control when electrodes are on top stops may cause some concern if baking of the electrodes is required in this scenario.

Jan 1, 2009

By A. K. Verma

Several longwall faces in India have collapsed due to adverse geological conditions and/or inadequate capacity of powered supports. Thus it is imperative to access the capacity of a powered support and its interaction at longwall faces of varying geomining conditions in advance with lots of confidence. To achieve this, an index has been developed to ascertain the front leg pressure (FLP) of chock-shield support and roof-to-floor convergence (RFC) at longwall faces. The index called ?Longwall Face Stability Index? (LFSI) has been developed using statistics and Finite Element Modelling (FEM). The front leg pressure (FLP) and roof-to-floor convergence (RFC) predicted from the LFSI are validated with the field monitored data from two longwall panels. In this study, an attempt is also made to incorporate various geomining conditions into the finite element models typical of longwall mining practice. The index has taken into account the wide variations of geomining parameters like thickness, young?s modulus and friction angle of main roof (small, large), coal type (soft, hard), powered support capacity, and depth of coal seam. Thus, LFSI can be thought of as an index representing combined effect of roof type, geomining conditions and powered support capacity.

Jan 1, 2008

By Lene Hansen

Sulphuric acid plants now and then see unexpected increases in SO2 emissions. Our experience is that it is not always easy for the acid plants to pin point the exact reason for the SO2 increase. Sometimes a catalyst bed is sacrificed even though reliable emperature readings and gas analyses could have verified satisfactory activity, hence the leaking heat exchanger is never discovered and after the shutdown the SO2 emissions are still too high. This paper will look into some basic catalyst management tools: Good record keeping is a necessity for collection of representative catalyst samples, reliable operating data is an inevitable starting point for all analysis and trending of operating data is a must for plant optimisation and troubleshooting. In addition these catalyst management tools will give a continuous updated knowledge of the catalyst status in each bed providing the basis for a more effective replacement strategy. The most typical reasons for increasing SO2 emissions will be presented together with easy guidelines for cross-checking of operating data, temperature optimisation and good record keeping.

Jan 1, 2009

By Lene Hansen

Sulphuric acid plants now and then see unexpected increases in SO2 emissions. Our experience is that it is not always easy for the acid plants to pin point the exact reason for the SO2 increase. Sometimes a catalyst bed is sacrificed even though reliable emperature readings and gas analyses could have verified satisfactory activity, hence the leaking heat exchanger is never discovered and after the shutdown the SO2 emissions are still too high. This paper will look into some basic catalyst management tools: Good record keeping is a necessity for collection of representative catalyst samples, reliable operating data is an inevitable starting point for all analysis and trending of operating data is a must for plant optimisation and troubleshooting. In addition these catalyst management tools will give a continuous updated knowledge of the catalyst status in each bed providing the basis for a more effective replacement strategy. The most typical reasons for increasing SO2 emissions will be presented together with easy guidelines for cross-checking of operating data, temperature optimisation and good record keeping.

Jan 1, 2009

Deciding on plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g/t of fresh feed has been assumed a reasonable starting point with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2012

This paper presents recent advancements in the MillMapper software technology, developed and used for thickness gauging of liners of cylindrical grinding mills used for mineral comminution. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces with millimetre accuracy. The paper is structured as follows. First, a review of the technology and its numerous advantages over existing techniques and the value it adds to operations are presented. These are followed by discussion of recently-implemented innovations, including improved visualisation and inspection tools, automatic ball charge volume measurement and automatic mill liner volume/weight measurement. Results from its application at several sites in Australia are presented throughout.

Jan 1, 2007

COUNCIL AND STANDING COMMITTEES - 1973-1974 Office Bearers: P. W. J. van Rensburg (President), Professor R. P. Plewman and Dr R. E. Robinson (Vice Presidents), J. K. E. Douglas (Honorary Treasurer), and Dr J. P. Hugo (Immediate Past President). Elected Members of Council: Dr M. G. Atmore, G. H. Grange, Dr P. R. Jochens, J. G. Kirchner, Dr D. I. Legge, W. W. Malan, Dr M. D. G. Salamon, L. W. P. van den Bosch, D. A. Viljoen, P. A. von Wielligh. Branch Chairmen: B. T. Hosking (Witbank-Middelburg Branch), E. T. Wilson (Orange Free State Branch). Past Presidents Serving on Council: R. J. Adamson, M. Barcza, H. Britten, H. E. Cross, Professor J. de V. Lambrechts, R. C. J. Goode, Professor D. D. Howat, D. M. Jamieson, D. G. Maxwell, Dr J. T. McIntyre, V. C. Robinson. Ten Council meetings were held during the year, with an average attendance of 19, and the standing committees held 30 meetings. COMMITTEE CHAIRMEN Membership, Dr R. E. Robinson ; Metallurgical Colloquia, Dr R. E. Robinson ; Mining Colloquia, L. W. P. van den Bosch; Awards, P. W. J. van Rensburg; Excursions, P. A. von Wielligh; Dinner, G. H. Grange ; Constitution, Rules and Policy, Dr J. P. Hugo; Adjudicating, P. W. J. van Rensburg; Mines and Works, W. W. Malan; Education, Dr J. P. Hugo. REPRESENTATIVES ON OTHER BODIES Associated Scientific and Technical Societies: Members : V. C. Robinson and D. G. Maxwell Alternates : P. W. J. van Rensburg and Dr J. P. Hugo. Federation of Societies of Professional Engineers Members : J. K. E. Douglas and P. W. J. van Rensburg Alternates : Dr J. P. Hugo and G. H. Grange. South African Council for Professional Engineers Members : R. C. J. Goode and J. K. E. Douglas Alternates: G. H. Grange and Dr R. E. Robinson. Engineers' Liaison Committee (Pretoria): Member: Professor J. de V. Lambrechts Alternate : Dr J. P. Hugo. MEMBERSHIP Seventeen Fellows and Members, twenty-three Graduates, ten Associate Members, twenty-two Associates, thirty-four Students, and seven Company Affiliates were elected during the year. Eleven Fellows and four Members were admitted to retired membership. Five Fellows were elected to Honorary Life Membership. Four Members, two Graduates, and one Student were transferred to Fellows ; eleven Graduates and Students were transferred to Members ; eight Students to Graduates; and four Students to Associates. A statement of membership as at June 30th 1974 and the end of the previous year is given in the following tabulation 30th - 30th June, - June, 1973 - 1974 Honorary Life Fellows 4 - 9 Honorary Fellows 9 - 8 Life Fellows 177 - 170 Fellows 536 - 544 Members 487 - 512 Associate Members - - 10 Graduates 128 - 130 Associates 186 - 194 Students 183 - 173 Company Affiliates 64 - 70 1 774 - 1 820 OBITUARIES Your Council records with deep regret the death during the year of the following members : Dr P. N. Lategan and Dr O. A. Jackson, Honorary Life Fellows and Past Presidents; C. Airth, T. L. Blunt, J. B. Dennison, A. E. Frazer, C. L. Lamb, V. O. Reid, K. Richardson and D. G. Roberts, Life Fellows ; H. F. Allan, J. T. Beaumont, M. Eisenstein, J. C. Hall, C. F. Louw, H. H. McGregor, R. Murchison, and J. E. Williamson, Fellows; and R. B. Miles, Associate. FINANCE The annual accounts, which follow this report, reflect a healthy position and show that measures taken by Council over the last few years to boost income have been successful. A higher income was needed not only to meet rising costs but also so that the services provided by the Institute for its members could be expanded. This year's income of R55 025 showed a further increase compared with last year's figure of R48 307. Income from subscriptions was higher mainly owing to an increased number of Company Affiliates, and this is indicative of the support given by mining and metallurgical companies to the good work being done by the Institute. Further sales of publications of the symposia held over the last few years again made a useful contribution to income of R4560. The first Winter School held in 1973 yielded a surplus of R7495 after the expenses had been deducted from the income received from registration fees. The cost of administering the Institute increased by R2212 compared with the previous year. Included in this was a donation of R1000 to the A.S. & T.S. Trust Fund. The cost of publishing and printing the Journal increased by R2034, but advertising and extraneous sales of the Journal were higher, with the result that the net cost of the

Jan 10, 1974

Council and Standing Committees, 1978-1979 President: Dr M. G. Atmore. Vice-Presidents: D. A. Viljoen and Dr P. R. Jochens. Honorary Treasurer: J. K. E. Douglas. Immediate Past President: P. A. von Wielligh. Members of Council: J. D. Austin, A. N. Brown, H. E. James, Prof. R. P. King, Dr D. G. Krige, Prof. F. Q. P. Leiding, D. G. Malan, C. S. McPhail, J. C. Mostert, G. Y. Nisbet, H. G. M. Rose, W. T. Ruhmer, G. C. Thompson, R. A. von Maltitz. Chairman, Witbank-Middelburg Branch: T. S. Wilmot. Chairman, Orange Free State-Klerksdorp Branch: H. M. W. Eschenburg. Past Presidents Serving on Council: R. J. Adamson, H. Britten, J. K. E. Douglas, Prof. D. D. Howat, Dr J. P. Hugo, D. G. Maxwell, Prof. R. P. Plewman, Dr R. E. Robinson, Dr M. D. G. Salamon, P. W. J. van Rensburg. Standing Committee Chairmen: Membership, Dr P. R. Jochens ; Technical Programme - Metallurgy, Prof. R. P. King ; Technical Programme - Mining, H. G. M. Rose; Vacation School - Metallurgy, J. C. Mostert; Vacation School - Mining, D. G. Malan/J. D. Austin; Awards, P. A. von Wielligh; Excursions, D. A. Viljoen; Adjudication, P. A. von Wielligh; Constitution, Rules and Policy, P. A. von Wielligh; Monograph Series, Dr R. E. Robinson; Professional and Technician Train¬ing Committee, Dr M. D. G. Salamon; Career Guidance, D. G. Malan; Phoenix National Committee, Dr R. E. Robinson; 1982 World Congress, Dr M. G. Atmore; Witbank Coal Colloquium, Dr P. R. Jochens; Mines and Works, P. A. von Wielligh.

Jan 1, 1979

By J. Bal, V. D. Dao, W. Li

"SynopsisThis study proposes a methodology for evaluating the risk of coal bumps in multiple-seam longwall mining. Both the stress field and the total energy release (TER) during retreat were evaluated in the specified case involving multiple-seam mining using the LaModel program. The results of numerical simulations indicated that both the peak vertical stresses on the panel edges and the peak TERs in the outby longwalls increased significantly as the horizontal offsets were reduced from 60 m to zero. With the comprehensive consideration of the stress field and TERs, a conservative offset of 60 m was ultimately adopted when developing the gateroads of the lower panel in the field. The field measurements indicated that coal bumps were avoided completely by employing the proposed design, and the maximum roof-to-floor and rib-to-rib convergences of the tailgate during retreat were only 360 mm and 576 mm, respectively.IntroductionCoal bumps – sudden, violent bursts of coal – pose a serious threat to the safe excavation of coal. Their occurrence depends on the properties of the surrounding rocks, stress field, and dynamic disturbance. The complexity of the mechanism of coal bumps is further enhanced in multiple-seam mining due to seam interaction. Multiple-seam mining is most frequently found in the coalfields in eastern China, such as Xuzhou, Xinwen, Zaozhuang, and Huainan. In the past, due to issues of availability, economics, and ignorance of the potential risk in multipleseam mining, coal seams in such conditions were mined without proper planning to account for seam interaction. Fortunately, studies published over the past three decades have raised awareness of the problems associated with multiple-seam mining, and indicated that the ground control issues induced by multiple-seam mining can be avoided and/or minimized with proper planning.A number of technical studies pertaining to the design of multiple-seam mines have been published. These studies can be divided into two groups based on their methodologies of design: empirical (Chekan and Listak, 1993; Haycocks and Zhou, 1990, Matetic et al.; 1987a, 1987b) and numerical approaches (Li et al., 2000; Maleki, 2007; Mark, 2007; Peng, 2007; Zipf, 2005). The majority of the extant studies on the interaction mechanisms in multiple-seam mining have focused on the load transfer during operation, resulting in the proposal of the pressure bulb theory (Forrest et al., 1987; Haycocks and Karmis, 1983; Peng, 2008; Peng and Chandra, 1980) and pressure arch theory (Holland, 1973; Oram and Ponder, 1997) to guide multiple-seam mine design. However, neither, of these theories can be used to evaluate the potential for coal bumps."

Jan 1, 2015

By D. F. Malan, P. M. Couto

We propose a layout design for the UG2 Reef where weak geological alteration layers are present. The collapse of the Everest platinum mine in South Africa indicated that these layers substantially weaken the pillars. The popular Hedley and Grant pillar strength formula cannot be used where these alteration layers are present. Underground investigations at Everest mine and numerical modelling of the layout were conducted using the TEXAN code and a limit equilibrium model. Simulations of a collapsed area and an intact area allowed for a preliminary calibration of the model. This was subsequently used to explore modified layouts for these ground conditions. An alternative is to compartmentalize the blocks of ore using barrier pillars. The numerical modelling predicted that the barrier pillars appear to remain stable even in the case of large-scale collapses, provided their width exceeds 25 m. Main access routes into the mine can be protected by a double row of pillars at least 15 m wide to provide a safe travelling way. As a cautionary note, these conclusions are based on the model calibration and this needs to be refined in future. Calibration of the limit equilibrium model remains a challenge owing to the large number of parameters involved.

May 3, 2023

By G. Coetzer

"Prior to operating a non-recovery coke pilot plant oven, it was essential to ascertain coal cake stability during the loading of a 1 m3 (1 m × 1 m × 1 m) coal cake into the cold pilot-plant oven by a pusher mechanism. Previously established laboratory-scale compaction parameters, to obtain coal cakes with sufficient stability, were employed during the loading tests of the coal cakes. Two different coals were evaluated, namely Waterberg semi-soft coking coal (sscc) and Oaky North hard coking coal.It was demonstrated that lower applied compaction forces (14%) can be utilized during 1 m3 compaction, in comparison to laboratory-scale tests, to obtain similar wet cake densities, owing to differences in the effect of frictional forces. Wet cake densities for Waterberg sscc improved slightly (3%) to 1.13 t/m3 when utilizing 79 t/m2 applied force for a 1 m3 coal cake, in comparison to laboratory-scale tests. Similar results were obtained for Oaky North hard coking coal, with a 6% density increase to 1.27 t/m3 at a similar applied force. Porosities decreased by 13% and 32% for Waterberg sscc and Oaky North coal, respectively, when 1 m3 compaction was compared to laboratory-scale tests. An opportunity exists to further decrease the porosities of Waterberg sscc during compaction, whereas acceptable compaction parameters were achieved for Oaky North hard coking coal. Most major vertical cracks and the partial collapse of coal cakes were mitigated, and high-stability coal cakes were obtained that could be successfully loaded into the pilot-plant coke oven by a pusher mechanism.Factors contributing to the instability of the coal cake during loading into the oven, such as vertical cracks, are (i) the cubic geometry (1 m3) of the coal cake, (ii) friction exerted by the oven floor, and (iii) mechanical problems, such as a misalignment between the pusher machine feeder plate and the oven floor. IntroductionOperation of the stamp-charging horizontal 1 t electrically heated coke pilot-plant oven at Exxaro Resources requires coal cake stability during the loading of a 1 m3 compacted coal cake into the oven. In this case, a pusher plate is utilized to push the coal cake into the oven over the oven floor. This is in contrast to a ‘spoon’ or bottom plate feeding mechanism as found in industrial horizontal coke ovens. The pusher plate loading mechanism dictates that the coal cake should possess high stability and inherent strength owing to frictional forces exerted by the oven floor. In order to obtain a coal cake of acceptable stability for the 1 t coke oven, various compaction parameters need to be verified and established."

Apr 1, 2019

By V. Sheikhzadeh, M. R. Sheikhzadeh, A. Haratian, M. Zare

High Pressure Grinding Roll (HPGR) as an efficient grinding technology plays a major role in mineral processing plants. Investigating the effects of this technology on different parts of mineral processing circuits reveals this technology’s capability. In this paper, HPGR grinding effects on an iron ore beneficiation circuit, in comparison with conventional crushing systems were studied. A representative feed sample was taken from an iron ore beneficiation plant, then crushed to minus 6 mm in a laboratory by two methods: HPGR and cone crusher, and finally a concentrate plant circuit was simulated. Plant simulation was performed by doing laboratory tests consisting of grinding, magnetic separation, flotation and filtration on HPGR and cone crusher products, respectively. According to comminution tests results, in particle sizes smaller than 6 mm, a cone crusher product is coarser than an HPGR product. Also, the Bond ball mill work index of the HPGR product was 10% less than the crusher product. Therefore, based on the Bond formula in applying HPGR, ball mill power consumption decreased by 12%. After ball milling to minus 100 microns, magnetic separation tests results showed that the recovery of the cone crusher circuit output was 90.8% and the product Fe grade was 66.4%. For the HPGR circuit these figures were 87.6% and 67.3%, respectively. Therefore, by using an HPGR, a higher Fe grade of the final concentrate was achieved. A flotation test was then performed on the magnetic separation concentrate, where the results showed that the crusher circuit recovery and the sulfur grade of the product were 96.5% and 0.192%, respectively; whereas the HPGR circuit recovery was 97.2% with a sulfur content of 0.185%. Findings revealed that flotation performance in the HPGR circuit was more efficient than the crusher circuit. Vacuum filtration tests on concentrate produced through the HPGR circuit resulted in a moisture content of 12% that was 2% higher than the crusher circuit’s concentrate in the same condition. Keywords: High pressure grinding roll, power consumption, magnetic separation, flotation, filtration

Jan 1, 2020

By G. T. van Rooyen

The susceptibility of a low-alloy steel that has been hardened and tempered-826 M40 (EN26)-to embrittlement by strain aging during service was simulated by artificial aging of specimens at 100°C. It was found that the brittle transition temperature of both monotonic and cyclically strained material was increased by only about 25°C as a result of strain aging. It is concluded that the susceptibility of low-alloy steels in the hardened, tempered condition is less than that of low-carbon steel, and that such steels qualify for exemption of the periodic 'annealing' required by the Mines and Works Act.

Jan 1, 1986

By R. R. M. Cousens, W. S. Garrett

SYNOPSIS The paper gives a background to the water hazards of the so-called West Wits Line and refers to some geological aspects of the Wonderfontein Valley in which the West Driefontein mine property lies. It describes the precautions taken against flooding during shaft sinking, development and stoping; these include cover hole drilling with cementation, provision for water storage in worked-out areas, installation of water tight bulkhead doors and pumping capacity well in excess of the mine's normal requirements. The plan of campaign adopted after the inrush took place is explained and the reorganization and expansion of pumping arrangements are discussed. When it became clear that the only means of saving the mine was to construct plugs to isolate the inrush while still maintaining all emergency pumping measures, the work was put in hand with the utmost dispatch. In considering the design of the plugs a number of major factors had to be taken into account. The most vital was the need for speed which was complicated by difficulty of access to the plug sites because of the huge volumes of water flowing in the drives. How this and other factors affecting plug design and construction, leakage problems, sequence of operations and final closure of the valves, were overcome is detailed in the paper. INTRODUCTION The inrush of water into the West Driefontein mine, the biggest gold producer in the world, which began on 26th October, 1968 and continued unabated for 23 days before the flood was stemmed, was unprecedented in the history of mining. Also unprecedented were the tremendous efforts and organization which made it possible to bring the situation under control and so save the mine from being lost for a matter of years. BACKGROUND Before going into details of how the situation was brought under control it is appropriate to consider the background to the event. The water problem on the so-called West Wits Line has been recognized for many years. As far back as 1912 the Pullinger Shaft, situated in the centre of what is now the Venterspost mine property, had to be abandoned because there were no means then available of coping with the large quantity of water encountered. To appreciate what vast quantities of water were involved, it helps to refer to some geological aspects of the Wonderfontein valley in which the West Driefontein property lies. The narrow tabular Witwatersrand gold-bearing beds, which dip at about 25 degrees towards the south, are overlain by a surface layer of dolomite which reaches a maximum thickness of some 4,000 ft at West Driefontein. A number of vertical syenitic dykes intersect the valley more or less at right angles to its course (Fig. 1). These dykes are about 150 ft thick on average and are spaced at about eight-mile intervals in the West Driefontein area. They penetrate both the dolomite and the Witwatersrand beds and as they are impervious to water they divide the valley into a series of large underground water compartments.

Jan 5, 1969

By Y. Zhou, G. Chisakuta, P. Bwando, G. Mitshabu

A newly started copper hydrometallurgical plant was confronted with a manganese oxidation issue in electrowinning. This oxidation, in the absence of the amount of iron required to stabilise the electrolyte oxidation-reduction potential, is known to produce oxidants (MnO2, MnO4) that can cause accelerated degradation of the organic phase components in solvent extraction and corrosion of lead anodes in electrowinning. The overpotential required to build up the protection layer on new anodes causes an increased electrolyte potential that creates oxidized species in the electrowinning tankhouse, and these species come back to solventextraction plant with the recycled spent electrolyte. This paper discusses the impacts of manganese oxidants on the health of a plant organic phase. It also outlines the actions taken using iron scraps and sulfur dioxide to mitigate the problem that happened due to the lack of ferrous iron sulfate available on site, as recommended for better control.

Jan 1, 2023

By N. Moemise, M. B. Shongwe, P. A. Olubambi, M. M. Ramakokovhu

"Near-infrared (NIR) spectroscopy sorting technology is incorporated in an automated optical mineral sorter that can discriminate between materials using the differences in characteristics when exposed to near-infrared radiation. During September 2014 to April 2015, a pilot plant that utilized NIR technology to discriminate between kimberlite and waste materials was commissioned to determine the viability of including this technology in the diamond winning process flow sheet at Cullinan Diamond Mine. The plant was used to minimize the waste content in the size fraction -70+35 mm that reports to the crushing section and then to the dense media separation process. This paper describes the initial test work, conducted at Mintek, that led to the decision to conduct a pilot-scale study. The mineralogical characterization of the feed and product streams to establish the sorting criteria and the operational data obtained during the pilot plant campaign are described. The results indicated a good possibility of discriminating between the kimberlite and waste material using NIR technology. However, the consistency of discrimination was not good enough to avoid the risk of potential diamond loss. Furthermore, a lower than expected availability of the machine reduced the throughput capabilities. IntroductionUsing near-infrared spectroscopy (NIRS) technology for ore sorting is a new concept for the mineral processing and mining industry. NIRS has been used for decades in the laboratory for the identification of pure minerals, and has its roots in the recycling, food, and pharmaceutical industries (Salter and Wyatt, 1991; Robben et al., 2009). Ore sorting in itself is not a new concept; it was introduced during the Stone Age with handsorting being the first method to separate valuable materials from gangue (Wills and Napier-Munn, 2006; Sassos, 1985). However, over the years the scale of mining has increased and hand-sorting has become challenging to implement (Joensson, 2014).Sensor-based sorting is an advanced technology that can help overcome problems such as ore dilution experienced in mineral processing operations. The benefits are lower energy and water costs, reduced ore dilution, lower environmental impact, and improved profit margin (Mathew, 1974; Jonsson, 2014; Salter and Wyatt, 2009; Death et al., 2009). In sensor-based sorting, materials are mechanically sorted based on certain physical properties that are detected by a sensor (Dalm, 2013). Research has found that with NIR scanners it is possible to obtain a ‘fingerprint’ of a sample that is directly related to its mineralogical composition. According to Woutruba et al. (2009), molecules absorb NIR radiation by means of electronic and vibrational transitions. Nowadays, there are many sensors available in the market that utilize different material properties; the choice of a sensor is dependent on the mineralogy of the ore."

Jan 1, 2016

By G. M. Evans, S. Mitra, G. J. Jameson, M. M. Hoque, E. Doroodchi, R. Moreno-Atanasio

In this study, the detachment behaviour of 314 μm diameter silica particles from a single 3 mm diameter bubble rotating in a confined cavity connected to a cross-flowing water channel was investigated. The liquid cross-flow generated a rotating flow inside the confined cavity, which was quantified using 2D particle image velocimetry (PIV) measurements. The fluctuating (x-y) velocity components inside the cavity for each cross-flow velocity, U, were then used to estimate the corresponding time/volume average turbulence intensity values, Ti. Turbulence intensity ranged from 9.3-16.2%. In the absence of a bubble, the rotating vortex within the cavity created a pressure field which decreased towards the centre of the vortex; wherein the lowest pressure zone was located at the centre of the cavity. The vorticity into the cavity was found to increase with increasing the turbulence intensity. A bubble, both without and with particles attached, was introduced into the cavity under different flow conditions and its motion was tracked using the shadowgraphy technique. Experimentally, it was found that the bubble-particle aggregate was trapped at the centre of the cavity (low-pressure region) following a spiral trajectory. An interface resolved 3D computational fluid dynamics (CFD) model was developed to predict the particle detachment conditions within the confined cavity. CFDpredicted vorticity in the absence of a bubble agreed well with experimental observation. The CFD analysis indicated that the vorticity inside the cavity was not significantly changed when a single bubble was introduced. On this basis, the computed vorticity was utilised in describing the force balance applied to the attached particle. Computationally, it was found that the critical turbulence intensity, beyond which the particle was detached from the bubble, was 14%. This value was consistent with the experimental observation of detachment at Ti at 15.7%, and above, but not at lower values. Keywords: Bubble, particle, turbulence intensity, vorticity, particle detachment, CFD, PIV

Jan 1, 2020

Notices STRASZACKERREPORT The Institute has received, for its information, a copy of the following letter, which was addressed to The Federation of Societies of Professional Engineers: REPORT: COMMISSION OF ENQUIRY INTO THE METHODS OF TRAINING FOR UNIVERSITY DEGREES IN ENGINEERING (STRASZACKER REPORT) Geagte Heer, VERSLAG: KOMMISSIE VAN ONDERSOEK NA DIE METODE VAN OPLEIDING VIR UNIVERSITEITSGRADE IN INGENIEURSWESE (STRASZACKERVERSLAG) Second International Symposium on Jet Cutting Technology This symposium, sponsored and organised by BHRA Fluid Engineering, of Cranfield, England, is to be held at St John's College, Cambridge, from 2nd to 4th April, 1974. Competition for student members of the South African Institute of Mining and Metallurgy Each year the Institute offers a prize (or prizes should the entries warrant it) of up to R100 for the best paper or dissertation on a topic appropriate to the interests of the Institute. Techomin 74 - World Mining Fair The above World Mining Fair, under the sponsorship of the International Committee for the Organization of World Mining Congresses and the Peruvian Government, is to be held in Lima, Peru, from 3rd to 12th November, 1974, to coincide with the 1974 World Mining Congress, which is to be held in Lima. NIM Reports Report No. 1435 The determination of chromium, manganese, iron, cobalt, and nickel by atomicabsorption spectrophotometry using the nitrous oxide-acetylene flame. Report No. 1463 Liq'uidus temperatures and activities of manganese (11) oxide in slags associated with the production of high-carbon ferromanganese alloys. Report No. 1467 The spectral analysis of solutions. 1. The analysis of rare-earth minerals. Report No. 1479 Infrared studies of the adsorption of oleate species on mineral surfaces,with special reference to fluorite. Report No. 1483 The South African manpower requirements in extractive metallurgy. Report No. 1484 Cost estimates for the production of copper wirebars from sulphidic ores. Report No. 1486 Review of the jluoro-chemical industry of the World. Report No. 1490 The adsorption of krypton, nitrogen, and water vapour on sodium oleate. Report No. 1491 Technology and economics of the Olaus kiln under South African conditions. De Beers Report The dry grinding of tungsten carbide/ steel combinations with diamond wheels. Metallurgical Directory The Israel Export Institute has just published the first edition of the Israel Metal Industry Directory, which gives pertinent information relating to the 750 Israeli manufacturers of metal products-addresses, annual turnover, and products- and to consulting engineers and export companies specializing in metal products. Visiting Nuclear Scientist The National Institute for Metallurgy has announced that Professor Vincent P. Guinn, of the University of California, is to spend his sabbatical leave (April to June) working with the Activation Analysis Research Group of the National Institute for Metallurgy.

By T. B. Beeton

In view of the limited reserves of good-quality coking coals in South Africa, Iscor has been involved in direct reduction since the middle sixties. Since the early seventies, its interest in direct reduction was stimulated further by a swing towards' continuous casting, which, in turn, contributed to a shortage of the scrap supply for electric-arc-furnace (EAP) steelmaking. Rock engineering The First International Conference-Rock Enginet:ring and Excavation in an Urban Environmentorganized by The Institution of Mining and Metallurgy and the Hong Kong Section of the Institution, in association with the Hong Kong Institution of Engineers, will be held in Hong Kong from 23rd to 28th February, 1986. SPOTLIGHT on Gold Fields National Engineering Awards For the Gold Fields Foundation National Engineering Awards, each university affiliated to the South African Federation of University Engineering Students (S.A.F.U.E.S.) selected a candidate who, in their opinion, presented the most outstanding design project in their final year during 1984.

Jan 1, 1985