Search Documents

By J-N. Oyourou, R. McCrindle, C. J. S. Fourie

"Many mines in South Africa were inappropriately closed and left unattended during the last century. These old mines are potential sources of environmental pollution and may pose a health risk to local populations, since the surrounds contain elevated levels of toxic elements. Soil from the old Edendale lead mine property in Mamelodi Extension 11, east of Pretoria, which was suspected to be contaminated with lead, was analysed. The mine, which primarily extracted galena, was decommissioned in 1938. During this study, the old mine property and surrounds were screened for zinc and lead using a field-portable X-ray fluorescence (pXRF) spectrometer. The metal concentrations, which ranged from 18 to 7 300 mg/kg for zinc and from 50 to 21 000 mg/kg, for lead, were plotted together with the GPS coordinates to produce a concentration distribution map for lead and zinc. This map revealed three anomalies of unacceptably high concentrations, possibly corresponding to areas where ore had been piled or dumped to waste from the old mine. Thirty-six of the soil samples that were analysed by pXRF on site were selected and analysed in the laboratory using inductively coupled plasmaoptical emission spectrometry (ICP-OES) for verification purposes. The zinc and lead concentrations obtained from the two analytical methods were compared using linear regression analysis. Excellent correlation was obtained between the results from the two methods (r2 = 0.99 for zinc and r2 = 0.95 for lead). IntroductionEarly economic development in South Africa was based mainly on mining. However, these activities left a legacy of approximately 6 000 improperly closed mines scattered throughout the country (SAI, 2009; van Schie, 2012). Due to their proximity to settlements, these abandoned mines may pose a potential health risk to humans and an environmental hazard. Mining activities generate large amounts of waste, mostly in the form of overburden and process tailings, which often contain high concentrations of toxic elements. Bioavailable toxic elements can contaminate crops growing in the polluted area (Kala, 2010; Marwa, Meharg, and Rice, 2012) or eventually migrate and detrimentally affect the groundwater (Rösner and van Schalkwyk, 2000). Moreover, sulfides accumulated in mine waste generate acid minewater (Rösner and van Schalkwyk 2000). Unfortunately, owners of mines, closed before the promulgation of the Minerals Act more than twenty years ago (Act 50 of 1991), avoided the compulsory rehabilitation of the environment enforced by this legislation. Toxic elements, such as lead, which were confined within ores, may become exposed through mining and are therefore more easily mobilized within the environment. Elements essential to human and plant metabolism, such as zinc, when exposed by mining activities, may become hazardous due to elevated concentrations (Aslibekan and Moles, 2003; Wuana and Okiemen, 2011). Humans exposed to potentially toxic metals may experience harmful effects as discussed elsewhere (Nriagu and Pacynar, 1988; Wayne and Ming-Ho, 2005)."

Jan 1, 2019

By M. G. Maruma, L. A. Mampuru

"Mill liner wear is a major cost item in the mining industry and there is continuous research to prolong the life of the liners. Over the years it has become apparent that even though high-chromium white cast irons are highly efficient as abrasion-resistant materials, a combination of wear resistance and fracture strength remains difficult to achieve. Increasing the hardness of the high-chrome white cast iron (HCWCI), which improves the resistance to abrasion wear, is often accompanied by a deterioration in fracture strength. Operational conditions inside the mill require that the liner should be made of highly wear-resistant material with some fracture strength. Vanadium additions ranging from 0.2 to 3 wt% were made to HCWCI in an attempt to refine the microstructure. It was found that an increase in vanadium content promotes grain refinement. A content of 1.5-3 wt% gave the best results as measured by the maximum breaking strength.IntroductionOver the years it has become apparent that even though high-chromium white cast irons are highly efficient abrasion-resistant material, a combination of excellent wear resistance and fracture strength remains difficult to achieve. The exceptional wear resistance of highchromium white cast iron (HCWCI) is attributed to hard chromium carbides embedded in an austenitic/martensitic/pearlitic matrix. When the chromium contents exceed 12 wt%, interconnected MC3-type carbides of conventional cast irons are replaced by rodshaped and isolated M7C3 carbides (Powell, 1980), leading to an improvement in the impact toughness, ductility and fatigue resistance. However, the main M7C3 carbides in HCWCI are hard and brittle and can provide an easy path for crack propagation. This limits the applications of HCWCI, particularly in severe impact conditions. Most operations involving HCWCI are in crushing and grinding and the life of a part/liner is limited by its wear resistance. However, improving the wear resistance of HWCI comes at the cost of a significant reduction in fracture strength. Concerns about premature failure of HCWCI mill liners in the mining industries prompted a study to improve the wear resistance and mechanical properties of HCWCI."

Jan 1, 2016

By S. M. H. Ahmadi, K. Barani, F. Moradpouri, R. Ghaedrahmati

As exploration is time-consuming, costly, and risky, determination of the erosion surface of a metalliferous deposit before geophysical surveying and exploration drilling might be very helpful. Geochemical haloes can be used to determine whether the erosion surface is supra-ore or sub-ore and thus reduce the risk of exploration operations. The aim of this investigation is to determine the erosion surface of the North ROK porphyry deposit (NRPD) in northwestern British Columbia in Canada using linear productivity (LP), which is the content of an element defining the halo multiplied by the width of the halo. A total of 2045 soil samples from the B horizon were analysed using ICP-MS for 36 elements, including Cu, Mo, Pb, Zn, Au, As, Ag, Ni, Co, Fe, and Mn. The data-set was snalysed to obtain the statistical parameters and the elements Cu, Mo, Pb, and Zn were chosen to calculate the linear productivity and the total linear productivity. These four elements were modelled using probability plots to identify and separate subpopulations in terms of anomalous haloes and background, including the threshold values of each subpopulation. The results of the probability plot modelling and thresholds values were then used to map the distribution of each element in a GIS to calculate the linear productivity. The total linear productivity indicated that the erosion surface is supra-ore. Finally, a 3D orebody model of the Cu, Mo, Pb, and Zn distributions was constructed using borehole data and used to validate the results.

Feb 6, 2023

By R. P. King

Held on the 22nd March 1972 at Kelvin House. Four papers were presented at this colloquium, which was attended by approximately 120 people. The first paper, 'Flotation Research Work at the N.I.M. research group, University of Natal on the modelling of a Flotation Process' was presented by Dr R. P. King, the leader of the N.I.M. Research Group in the Department of Chemical Engineering at the University of Natal. A discussion panel, under the chairmanship of Dr R. E. Robinson with Mr M. Dawson (PMC), Mr E. Roux (FOSKOR), and Dr B. K. Loveday (NIM), discussed the potential application of the theoretical work on flotation modelling to industrial processes, and alternative approaches to providing a way of control of flotation plants. The second paper, 'Fundamental Studies of the Flotation Process the Work of the National Institute) for Metallurgy', was presented by Dr N. P. Finkelstein. The discussion panel for this paper was under the chairmanship of Professor D. D. Howat,and had as its members Mr H. P. Carlisle (JCI), Professor D. le Roux (University of Pretoria), and Mr E. Rudolph (Anglo American Research Laboratories). A lively discussion on this paper ensued, with several contributions from the floor. After lunch, Mr S. K. de Kok, Assistant Consulting Metallurgist, Anglo Vaal, presented a paper on 'The Flotation of Copper and Zinc Sulphide from Prieska Ore'. The paper was discussed by a panel comprising Dr V. C. Lovell (NIM), Mr A. Gilbert (General Mining), and Dr D. Legge (Anglo Vaal), under the chairmanship of Dr L. Bushell. This discussion, in which many members of the audience participated, revolved around the difficulties associated with the production of copper and zinc concentrates and the lack of fundamental information on the behaviour of copper and zinc sulphides in flotation. The final presentati0n was a paper, 'The Recovery by Flotation of Cassiterite contained in Gravity Concentration Plant Tailings', presented by Mr E. B. Viljoen (Metallurgy Department, Goldfields South Africa Limited). The discussion, led by a panel consisting of Mr O. Tant (Goldfields Laboratories), Mr J. Levin (NIM), and Mr R. I. Shanks (NIM), under the chairmanship of Mr H. Cross (Goldfields South Africa Limited) referred particularly to the use of new reagents for the flotation of tin, with particular emphasis on the fundamental relationship between reagent composition and its ability to float this type of mineral.

Jan 4, 1972

By D. F. Malan, L. Scheepers

Seismic risk in the deep gold mines of South Africa has been studied for many decades. A clear understanding of the effect of geotechnical conditions on the seismic hazard nevertheless remains elusive. Certain reef types seem to be associated with a higher risk of rockbursts. The stability and deformation behaviour of excavations on the different reef horizons are affected by the rock types and the varying strength properties. The seismic response to mining is therefore also expected to differ according to the geotechnical conditions. As a case study of this behaviour, the seismicity at Mponeng mine was investigated. On the VCR (Ventersdorp Contact Reef) horizon, two areas can be delineated. On the eastern side of the mine, the footwall is shale, and on the western side it is a strong brittle quartzite. More large-magnitude events occur in the area with the shale footwall than the area with the quartzite footwall. Moment tensor analyses indicated that the majority of the large-magnitude events are not related to geological structures, but are face-related, implying that shear failure of intact rock is occurring ahead of the mining front. Preliminary modelling indicated that the closure volume for the shale footwall may be higher than that for the quartzite footwall, providing a possible explanation for the observed difference in seismic response.

Mar 2, 2022

10th COMMONWEALTH MINING AND METALLURGICAL CONGRESS-CANADA, 1974 The Commonwealth Council of Mining and Metallurgical Institutions has received and accepted an invitation from The Canadian Institute of Mining and Metallurgy for the 10th Commonwealth Mining and Metallurgical Congress to be convened in Canada in April, 1974, immediately following the Annual General Meeting of The Canadian Institute of Mining and Metallurgy. It is proposed that the Congress centre will be Montreal and that, after technical sessions, tours of operations will be arranged. Further information will be issued in due course by The Canadian Institute of Mining and Metallurgy and enquiries should be addressed to the Executive Director of the Institute, 906-1117 Ste. Catherine Street West, Montreal 110, P. Quebec. NOTICE TO ALL STUDENT MEMBERS OF THE SOUTH AFRICAN INSTITUTE OF MINING AND METALLURGY The Institute offers each year for competition among Student Members of the Institute a prize, or prizes, should entries so warrant it, of up to the value of R100 to be awarded to the Student Member or Members who submit the best paper or dissertation on a topic appropriate to the interests of the Institute. In the case of Student Members who are in full time study at a university the dissertation or thesis which they may have to write in part fulfilment of their university curriculum may be accepted provided it is presented in a manner and on a topic suitable for publication in the Journal. The closing date for the receipt of papers shall be 31st December each year.

By G. A. Georgalli

A control philosophy to be applied by Lonmin to maintain constant electrode immersion in their no. 1 circular smelting furnace is put forward. This control philosophy is facilitated though a combination of thermodynamic models used to predict the slag composition and empirical correlations to estimate the furnace geometric factor as well as the slag conductivity. The model can determine the operating resistance set point required in order to maintain a desired electrode immersion as a function of the feeds to the furnace, slag level and temperature. If modifying the resistance set point cannot maintain the desired immersion without moving out of the furnace P-V-I operating envelope, the model can be used to determine the amount of slag modifiers (silica or lime) required to shift the slag chemistry back into a region where the immersion can be controlled though resistance set point manipulation.

Jan 1, 2008

COUNCIL FOR 1988/89 President C.E. Fivaz President-elect Dr O.K.H. Steffen Senior H.G. Mosenthal Vice Presidents Junior R.D. Beck Immediate Past President B.C. Alberts Honorary Treasurer Dr H. Wagner

Jan 1, 1989

By G. Mucsi, F. Kristály, R. Szabó

Kaolin is one of the most important ingredients in porcelain manufacturing. Its main phase is clay mineral containing aluminum hydrosilicate, namely kaolinite. Beside kaolinite it also contains quartz, illite and feldspars, which impair its applicability. Kaolin is a non-reactive material, but metakaolin can be produced by heat treatment (calcination) of kaolin, which is also used by the cement and concrete industry due to its latent hydraulic (pozzolanic) properties. Beside thermal activation, reactive materials can also be produced by mechanochemical activation in general. This paper deals with the mechanochemical activation of kaolin. The raw material was classified into various size fractions, then ground in a batch stirred media mill under varying circumstances (residence time, circumferential velocity). After grinding, the structural changes of the products were investigated by X-ray diffractometry (XRD) and Fourier Transform Infrared Spectroscopy (FTIR). In addition, the particle size distribution of the ground material was determined by laser scattering. As a result of the grinding experiments and analytical measurements of the products, it can be clearly seen that reactivity of kaolin can be improved significantly by mechanical activation in a stirred media mill, but due to its high energy density the circumstances were optimised carefully to avoid aggregation. Keywords: Kaolin, grinding, stirred media mill, mechanical activation, material structure

Jan 1, 2020

By H. Vuthaluru, O. Kavianipour, C. -Z. Li, N. Suresh, D. Sahu

The paper describes a CFD model developed for 76mm Dense Medium Cyclone (DMC) using Ansys Fluent Software to gain insights into the separation of particles according to their size and density. The simulation used in this paper includes the Reynolds stress model to predict the turbulence inside the cyclone body. An Eulerian-Eulerian multiphase CFD model was applied to model a number of physical aspects such as the separation of coal particles and the segregation of magnetite media solids. The experimental results generated in a laboratory scale DMC were used for the validation purpose and the predicted results of CFD have been validated for the flow splits of water, magnetite and coal. The simulation results obtained from the Eulerian-Eulerian multiphase model revealed that the prediction agreed with experimental results, and matched reasonably well in terms of the mass flow rates of water, magnetite and coal. Furthermore, the partition curve of the DMC when mapped for the separation of - 3.0+0.50 mm size also showed to be in agreement with the experimentally obtained curves. The gravity of cut (SG50), also predicted by the Eulerian-Eulerain multiphase CFD model, was found to be in the vicinity of observed experimental value of SG50. Keywords: Dense medium cyclone, Eulerian-Eulerain multi-phase modelling, computational fluid dynamics, cut gravity (SG50)

Jan 1, 2020

By B. McFadzean, M. Becker, S Geldenhuys, A. Molifie

Mineral hydration is known to result in low flotation recoveries and grades within primary platinum group element ores worldwide. This is because the phyllosilicate minerals derived from hydration reactions of silicate minerals (i) form electrostatic coatings on valuable minerals that in turn hinder collector adsorption, (ii) alter the viscosity of the slurry leading to poor gas dispersion and (iii) decrease the concentrate grade due to naturally-floating gangue. Sodium silicate was investigated because its dispersant, rheology modifying, and depressant properties could prove promising in combating the problems associated with these ore types. Quantitative evaluation by scanning electron microscopy analysis revealed large quantities of serpentine and talc present within the ore sample used in this study, which led to a poor flotation response as indicated by batch flotation tests. Using sodium silicate improved the recoveries and grades at high dosages (>1000 g/t). The zeta potential experiments indicate that improved recoveries are, in part, as a result of the reversal of serpentine surface charge, creating electrostatic repulsion between serpentine and valuable minerals which prevents the coating of valuable minerals by serpentine slimes. Ore dilution and rheology tests indicated that decreased viscosity at high dosages also improved recoveries. Talc micro-flotation tests revealed that the depression of talc occurred at higher sodium silicate dosages, which improved concentrate grade. The processing of nearsurface altered ores is becoming an increasing problem worldwide and the use of sodium silicate proved valuable in mitigating the problems associated with the altered ore investigated in this study. Keywords: Alteration, phyllosilicate slimes, colloidal chemistry

Jan 1, 2020

By C. B. Carelse, M. Manuel, D. Chetty

Automated mineralogical analysis of platinum group minerals (PGM), using the mineral liberation analyser, provides information used to understand flotation efficiency, primarily from a PGM liberation and association standpoint. To date, however, there is no consistent understanding regarding PGM speciation and its impact on floatability. Previous studies of PGM from UG2 ores concluded that a larger dataset is needed from which the various parameters can be modelled. Parameters on telluride, arsenide, sulfurarsenide and alloy species need to be integrated to fully understand the impact of PGM speciation on flotation, and for this, ores other than PGE-sulfide-rich UG2 must be assessed. Flotation rougher rate tests were performed on feed samples from two Platreef ores to determine the flotation response of individual liberated PGM species. This was achieved through automated mineralogical analysis of feed, rougher concentrates and tails. Based on 1529 liberated PGM grains assessed over the circuit for two Platreef ores, preliminary results show that PGM speciation, species grain size and competition from gangue appear to influence floatability in an ‘optimised’ laboratory environment. Keywords: PGM, PGM species, flotation, liberation

Jan 1, 2020

By J. P. De Carvalho, R. Dimitrakopoulos

This paper presents an actor-critic reinforcement learning (RL) method to allocate trucks and shovels in open-pit mines, while defining short-term production scheduling of an industrial mining complex, given new information collected during operations. This new data obtained from sensors update the uncertainty of the orebody models. The RL agents interact with the mining complex environment; exploring the solution space, learning actions to improve metal production and equipment utilisation. A case study is presented at a copper mining complex, highlighting the method’s ability to adapt and make informed decisions while collecting new information.

Sep 1, 2021

By A. P. Cook

Gas samples were taken from a wide range of target areas on dumps arising from coal mining activities. Some of the dumps had largely burned out, some were still burning, some were in the process of rehabilitation, and on others rehabilitation was essentially complete. It was found that rehabilitation was very effective in reducing emissions to tolerable levels. Even incomplete rehabilitation reduced the CO2 emissions to less than about 1 kg/m2/a, whereas some unrehabilitated areas showed emissions of over 100 kg/m2/a. Some areas where there was active combustion taking place were also sampled, and they showed as much as 7 000 kg/m2/a, but the areas concerned were very small and their total contribution accordingly low. Analyses were also made for SOx, NOx, NH3, and CH4, but these were generally (and unexpectedly) at very low levels. The mines sampled represented 53 per cent of all surface coal mining activity. Accordingly the estimated total emissions were scaled up, to arrive at estimates of 1950 000 ± 350 000 t/a C02, 2040 ± 580 t/a SOx, 306 ± 85t/a NOx, and 31 ± 9 t/a NH3 for all surface mines. Methane was detected only from burning coal, and due to the difficulty in sampling, no reliable estimate could be made of these methane emissions.

Jan 1, 2012

The visit which took place on the 18th February, 1972 was a departure in that the places visited had no direct connection with the work in which members of the Institute are normally engaged. It was refreshing and stimulating to see important and involved operations normally outside ones own trend of life and to have experts to speak about technical, financial and matters of general interest concerning their work, not forgetting their troubles and problems and how they overcame them. Carlton Centre The members of the Institute were received by Mr D. Appleton, Public Relations Officer of the Carlton Centre Limited, who introduced Mr L. R. M. Fee of W. Rhodes Harrison, Architect in charge of the project; Mr W. C. E. Skilton of Murray and Roberts, the Engineer in charge of the construction of the complex and Mr A. Home the Senior Operating Engineer of Carlton Centre Limited. Each of these gentlemen addressed the members giving short rundowns on the project with special reference to their particular sphere of the undertaking. A variety of particularly interesting statistics relating to the planning construction and the ultimate operation and maintenance of the complex was given. Mining engineers present had an opportunity to compare the problems encountered by them associated with depth to problems encountered by the civil engineer in the construction of a building rising to such an enormous height. To some of the members a sense of similarity of the labour problems encountered must have been recognised. After tea the visitors were divided into groups, each under the guidance of an official, and then visited the highest floor accessible and thereafter the 19th floor where the internal arrangements for airconditioning, lighting, plumbing, power supply and communication arrangements were explained. Thereafter a visit to one of the seven basements which houses all machinery required to serve this enormous complex enabled the visitors to see the standby power arrangements as well as the refrigeration plant. The visit finished in time to proceed to the Crest Hotel in Hillbrow for lunch. To our hosts for the visit to the Carlton Complex a special vote of thanks is recorded. Strydom Tower In the afternoon the party proceeded to the Strydom Tower where Mr Knight from the Public Works Department who was the Engineer in charge of the construction of the tower gave details on the construction and the extraordinary methods which had to be adopted to achieve the desired objectives and to overcome known as well as unforeseen difficulties. The comparatively short time taken to complete the project and the good safety record appeared to impress the visitors. The final phase of the visit was taken care of by Mr Bothma of Telecommunications Department of the Post Office, who gave an extremely interesting explanation of the telecommunication organization of the Post Office with particular reference to the part the Hillbrow Tower plays in the South African telecommunication system. Both gentlemen answered many questions willingly and interestingly. Following the explanatory talks the visitors were shown the technical equipment housed in the two top levels of the tower. Short explanatory talks gave members an insight into the workings of one of the most important aspects of modern life. Even to the amateur photographer opportunities existed to view and photograph the city from the highest available observation point. We are indebted to Mr Gouws, the Regional Director of the Post Office for granting permission to visit sections of the tower normally not accessible to the general public and to our hosts for the manner in which we were received and entertained on the explanation of the many interesting features of this important installation. In conclusion, the programme for the day can be classified as interesting, of exceptional educational value, and an opportunity to see something of the engineering skills put into two vast and ambitious undertakings and the results achieved.

By J. E. Dickinson, J. L. Sutherland, J. Zhou, M. J. Cole, K. P. Galvin

Interest in early gangue rejection has grown substantially in the minerals industry to reduce energy and water consumption arising from excessive comminution. Recent developments in coarse-particle flotation have proven successful by promoting a quiescent hydrodynamic environment to limit particlebubble detachment and by helping to convey more buoyant particles to the overflow. Current approaches also benefit from upstream classification to remove the finer particles ahead of the coarse-particle flotation. In this study, coarse-particle flotation was investigated experimentally using a novel hybrid gravity-flotation system called CoarseAIR™ that exploits the hydrodynamic advantages of the Reflux® Classifier. The system consists of a lower fluidised bed housing, with a system of inclined channels above. The inclined channels enhance the segregation and hence rejection of intermediate through to relatively coarse particles containing little or no surface liberation. This approach overcomes the need for pre-classification, while offering strong transport of coarse particles made buoyant through their attachment to air bubbles. The paper explores the strong relationship between the solids transport to the overflow and the input gas flux, showing firstly the potential for significant mass rejection at the relatively low gas fluxes, and robust performance in terms of recovery across the full range of gas fluxes. Keywords: Flotation, inclined channels, coarse particle flotation, Reflux Classifier

Jan 1, 2020

By M. Tang, X. Tong

"SynopsisSlime coating is one of the most common ways for serpentines to contaminate metallic mineral concentrates during traditional flotation of coarse sulphide particles. This could pose quite a complicated and challenging problem in the case of some types of low-grade and finely disseminated Cu-Ni ores bearing high serpentine contents. This is the case for the copper and nickel sulphides from the Yunnan Mine, China. Previous batch flotation tests of this ore resulted in satisfactory recoveries of 86.92% Cu, 54.92% Ni, and 74.73% Pt+Pd, and concentrate grades of 4.02% Cu, 3.24% Ni, and 76.61 g/t Pt+Pd. However, the MgO content in these concentrates was more than 19%. In the current study, microflotation tests and settling rate tests were introduced to investigate the effects of a combination of strong collectors (a 2:1 weight ratio of butyl xanthate and butyl ammonium dithophosphate) on entrainment of serpentines in metallic mineral concentrate, as well as visual observations of the concentrates in suspension using still photography. All test results indicated the presence of serpentines entrapped in the hydrophobic flocs that resulted from these collectors, even with the use of effective gangue depressants. These strong collectors are used to flocculate the ultra-fine sulphides by forming loose and ‘fluffy’ hydrophobic flocs. However, these hydrophobic flocs may also be able to load or entrap some serpentine slimes into the concentrate, and this entrained serpentine could be harder to remove by using depressants or intensified conditioning than serpentine slime coating on the particle surfaces.IntroductionSerpentine minerals, which have the generalized composition (Mg,Fe)3Si2O5(OH)4, can be easy to crush and grind due to their convoluted and bent layered structures. These serpentines can hinder the enrichment of some metallic minerals and dilute their concentrates by entrainment during flotation. The resulting high pulp viscosities, slime coatings, and high content of dissolved ions adversely affect the flotation recoveries of copper and nickel sulphides, and high levels of MgO entrained in the concentrates lead to heavy penalties from smelters. Since the quality of nickel flotation concentrate depends heavily on its MgO content (generally less than 6–7% for No.1 or 2 grade nickel concentrate according to the standard requirement from National Nonferrous Industry), reducing the entrainment of serpentine during flotation is becoming more and more pressing. Previous research has focused on the collectors and depressants that are commonly used in copper-nickel flotation, as well as their interaction mechanisms."

Jan 1, 2015

By S. G. Mgenge, J. D. Steenkamp

Tronox Namakwa Sands operates two ilmenite smelters for the production of high-titania slag and low-manganese pig iron. Slag or metal is tapped from one of two product-specific, bi-level tap-holes. In this paper the refractory design specific to the tap-hole refractory layout is described, as well as practices for slag and metal tapping and refractory maintenance. Further developments planned are briefly described.

Jan 1, 2014

COUNCIL FOR 1989/90 President Dr O.K.H. Steffen President-elect Mr H.G. Mosenthal Senior R.D. Beck Vice Presidents Junior ].P. Hoffman Immediate Past President C.E. Fivaz Honorary Treasurer Dr H. Wagner

Jan 1, 1990

By E. Moosavi, K. Tolouei

In mine production scheduling problems are well-known, where most are categorised into deterministic and non-deterministic NP-hard problems because of their complexity. Many researchers have attempted to solve the problem by applying various optimisation techniques. While using traditional methods they observed extreme difficulty in solving highly complex problems. In the 1990s, many researchers addressed long-term production scheduling (LTPS) by using simulated annealing, the genetic algorithm, the tabu search algorithm, and the ant colony algorithm. These algorithms are known as the meta-heuristic algorithms, and have proved to be the most efficient algorithms for solving LTPS thus far. The firefly algorithm is one of the best methods for visualising problems related to LTPS, and provides the best possible optimisation. It is one of the simplest methods, and easy to apply to any NP-hard problem. The experimental, and comparison with other recently published algorithms shows that the proposed algorithm is feasible, and is an effective approach for long-term production scheduling problems. The results indicated that a better solution is obtained by the proposed method, compared to other methods in terms of cumulative net present value, and average ore grade. Additionally, the CPU time via the proposed model is roughly 2.52% higher than the other method.

Sep 1, 2021