Search Documents

When a mine decides to construct surface structures close to, or on undermined ground, it is required in terms of the regulations of the Mine Health and Safety Act to obtain permission from the Department of Minerals and Energy (DME). Apart from the legal requirements, the stability of the structures is crucial as damage to the structures due to surface movements could result in loss in life, equipment and/or production. This paper deals with the rock engineering aspects of a study that was conducted on one of the chrome mines in the Bushveld Complex (BC) involving the construction of plant structures on shallow undermined ground. The paper addresses the legal requirements and guidelines regarding ground stability of surface structures placed on undermined ground and the assessment of the undermined area with regard to the following: ?sources of potentially damaging surface movements ?safe mining spans ?stability of the pillars ?effect of the loading of plant structures on underground stability. Due to the irregular layout and geometry of the pillars in conjunction with a changing surface topography, numerical analysis and not the conventional tributary area theory was used to determine the imposed loads on the pillars. In order to subject the plant structures to minimum movement, the plant should be located in areas where the pillars would remain stable, the elastic deformation of the hanging wall is minimized and hanging wall failure extending to surface is unlikely to occur. The study indicates that although the depth of undermining is shallow (between 27 m and 60 m), potential damaging surface movements are not anticipated due to the stability of the pillars, competent nature of the overlying strata and negligible effect of the plant structure loading on the underground stability.

Jan 1, 2004

By G. Mitchell

Much debate has ensued over the past few years on the speed of transformation in the mining industry. By transformation is meant the degree to which the industry has met the requirements of the Mining Charter. In response to this, the Department of Mineral Resources (DMR) commissioned a research study in 2009 to ascertain the degree of industry compliance. The mining industry in response made a presentation to the Minerals Portfolio Committee in Parliament in 2011, during which it released aggregated figures on industry compliance to the Mining Charter. The conclusions of both of the studies are widely divergent. It is argued in this paper that both processes are flawed. The government-sponsored research is empirically and methodologically weak and the results therefore have to be taken with a great degree of caution. The Chamber of Mines figures, on the other hand, while faithful to the reporting of the Chamber member companies, do not represent the entire span of the industry but only the larger mining companies. It is further argued that in order to ascertain a true reflection of the industry an independent audit be undertaken using recognized social scientific survey methods.

Jan 1, 2013

By G. Newson, N. Runciman

In 1999, INCO Limited Mines Research, in Sudbury, Ontario, Canada, took delivery of a MeycoRobojet Logica Spraymobile, a computerized concrete spraying system. The Spraymobile is a self-contained mobile machine capable of applying spray-on ground support in underground applications. The Logica component of the Robojet is designed to control the operation of the Robojet, as well as scan and map the tunnel geometry prior to the spraying operation. The Robojet can be operated in various modes, from manual to automatic operation. In the automatic mode the computer controls the standoff distance, angle, and motion of the spraying jet. In 2000, INCO Limited, working with Meyco Equipment of Switzerland (a division of MasterBuilders Technologies), detailed a plan to create a tele-operation package for controlling the spraying process from a surface location at INCO's Mines Research Test mine. With the RobojetLogica operating in automatic mode, the operator at the machine becomes a process monitor. Since the Logica system controls the key spraying parameters of nozzle distance and nozzle angle to the sprayed surface, the operator could easily monitor and control the Robojet Logica from aremote location. The benefits of operating underground mobile mining (drills and LHDs)equipment from a surface location has been demonstrated at INCO Limited, however, the abilityto control a ground support operation (shotcrete spraying) from surface has not been attempted until now. This paper will describe the Spraymobile shotcreting system, the development of the tele-operation package for the Robojet Logica, as well as modifications to the original Spraymobile for implementing the tele-remote package on the Robojet Logica at the Mines Research test mine.

Sep 1, 2001

By A. Montini

The problems encountered in the design of control systems for milling cir- cuits when the model of the system and the model parameters are uncertain are discussed. Considering these uncertainty factors has led to the development of a technique that gives a quantitative assessment of real system stability, reveals the trade-offs between performance and stability and helps the designer in deciding what level of model complexity to use in the controller design. Furthermore, it allows for on- or off-line optimization of the milling circuit performance as it provides the base for the design of a controller which is stable over the plant operating range.

Jan 1, 1987

By k. Lebecki, S. Trzcionka

The prototype and test results of the instrument for quick determination of incombustible content in deposited dust as a protection against coal dust explosion propagation are presented. Presently existing methods do not permit to obtain quick information about incombustible content, needed for the proper protection of workings. As the operating principle for the e instrument the dependence of reflection of infrared radiation intensity on incombustible content in the sample is chosen. The construction is based on the modern electronics. The measurement will be done at the sampling site. The range of the instrument is 0-100% of incombustible, direct reading, autonomous supply, weight no more than 0.5 kg, and is intrinsically safe according to EN Standards. During the Conference the instrument will be commercialized.

Jan 1, 2003

By A. Cáceres, L. Navarro, N. Altmann, R. Betinol

Copper concentrate is produced in Chile in the high Andes and transported to the coast for shipping through long distance pipelines. The pipeline and fittings installed have to withstand the high abrasion and corrosion environment of the copper concentrate. To protect the inside tube wall against corrosion, high density polyethylene (HDPE) liner is used. While HDPE liners can protect the steel wall against corrosion, it has also been assumed that the low surface roughness of the HDPE liner also inhibited incrustation caused by calcium carbonate and sulphate deposition. Recent events have indicated otherwise in a couple of concentrate pipelines for which BRASS has provided consultant service. This paper delivers a case study which includes (i) formation of incrustation and adhesion to HDPE liner, (ii) the detection of the incrustation through hydraulic analysis, (iii) the mechanism of removal of incrustation, and (iv) the catastrophic effects of their presence in an emergency situation.

Jan 1, 2007

By J. A. Venter, M. K. G. Vermaak, J. G. Bruwer

Electrostatic separation is employed in the concentration of zircon and rutile. The zircon concentrate undergoes an acid treatment to remove impurities from the surface of both the zircon and rutile. The purpose of the acid treatment is to increase the difference in the resistivities of the two minerals, thus ensuring the best possible electrostatic separation efficiencies. Previous test work suggested that these impurities are not removed, but only modified; the surface modification seemed more prevalent in the case of the rutile. The resistivity of the rutile changes with pH and thus the electrostatic separation of the rutile is influenced. X-ray photoelectron spectroscopy (XPS) indicates that there is an increase in the OH and adsorbed H2O concentrations on the rutile surface. XPS also showed significant differential charging on the rutile surface, which indicates that the species on the rutile surface have different resistivities. The zircon particles from the conducting and non-conducting streams have similar resistivities and no major differences in their surface species. Zircon losses during the final electrostatic separation appear not to be due to surface effects, but due to shielding of particles during the separation.

Jan 1, 2007

By D. Seke

Metal inventories are usually reported in financial statements of mining companies. However, the value of these inventories can be reliable only if the metals in stock are measured within acceptable tolerances. Reliable metal balancing requires accurate mass measurement, sampling, and chemical analysis. Many mining companies are usually unable to validate the accuracy of metals in inventories at the end of their financial year. This is mainly due to poor mass measurement, sampling, and chemical analysis practices. This has an adverse impact on metallurgical accounting and metal valuation. In addition, it puts a lot of stress on external auditors, who have the duty to recommend the approval of the financial statements to the board of directors. Although a full value chain of metal reconciliation includes the accuracy of Mineral Reserve definition and grade control at the mine, this paper discusses the implementation of best practices for mass measurement, sampling, and chemical analysis at processing plants. This is an important aspect of sampling and reconciliation that is required in order to improve the reporting of inventories in the financial statements of public mining companies. Keywords metallurgical accounting, corporate governance, sampling, analysis.

Jan 1, 2014

By Q. G. Reynolds

The dual-electrode DC arc furnace, an alternative design using an anode and cathode electrode instead of a hearth anode, was studied at small scale using computational modelling methods. Particular attention was paid to the effect of two key design variables, the arc length and the electrode separation, on the furnace behaviour. It was found that reducing the arc length to brush arc conditions was a valid means of overcoming several of the limitations of the dual-electrode design, namely high voltages and arc deflection.

Jan 1, 2012

By R L. Bowers, D S. Smit

In light of soaring commodity prices, Nkomati has investigated the potential of processing additional low grade nickel ores to add to their reserves. The Chromititic Peridotite Mineralised Zone (PCMZ) was identified as one ore type with the potential of producing a high grade nickel concentrate. In addition to the nickel, copper, cobalt and PGM?s, the ore also contains a significant amount of chromite which adds substantial value to the project. Pyrrhotite, pentlandite, chalcopyrite and chromite are the dominant minerals within the ore, which on average grades around 0.23% Ni and 12% Cr2O3. The PCMZ ore contains excessive amounts of fibrous silicates which makes it a challenging float, with gangue control as the key element to success. Extensive laboratory testwork, which eventually led to a pilot plant campaign, was undertaken with the aim of developing a process route for treating the PCMZ ore. Several flotation circuit configurations were tested and results from the optimal circuit indicated that a nickel concentrate grading at 8.5% is achievable at a recovery of 78%, with substantial recoveries for the copper, cobalt and PGM co-products. The chromite concentrate, grading at 45%, was extracted from the flotation rougher tailings via a spiral plant. These promising results were incorporated into the plant design and are currently being evaluated in a bankable feasibility study, which will see the current 100ktpm MMZ concentrator being upgraded to a 250ktpm PCMZ concentrator as part of Nkomati?s Phase II expansion.

Jan 1, 2007

By T. Bednarski, L. Thomas, G. Banza, D. Muteba, P. Cole, M. Soderstrom

"In copper solvent extraction, aqueous-in-organic entrainment results in the carry-over of unwanted species into the electrowinning process with negative cost implications. The need to bleed is increased and the purity of the copper cathode is potentially compromised, depending on the impurities being transferred (Cl, NO3, Fe, Mn). In some cases, entrainment results in elevated levels of manganese in the electrolyte which can cause oxidative conditions to develop and degradation of the organic phase. Degraded organic phase detrimentally affects the physical performance of the copper solvent extraction process, contributing to even higher aqueous-in-organic entrainment. Aqueous entrainment may be minimized through good operating practices and maintenance of the organic quality, but the accurate measurement of entrainment remains a challenge. This paper presents coalescing devices designed to provide more exact measurements of aqueous-in-organic entrainment. IntroductionMany copper solvent extraction (SX) plants experience high aqueous-in-organic (A-in-O) entrainments but are unaware of the extent of the problem because entrainment is often not measured. Aqueous entrainment results in the carry-over of unwanted species into the electrowinning (EW) process and the need to bleed to maintain acceptable concentrations in the electrolyte. The costs associated with the bleed are exacerbated in copper plants where aqueous entrainment levels are high. Other than these direct costs, there are operational consequences of the build-up of certain species in the EW circuit that can have deleterious effects on plant performance.Minimizing aqueous entrainment in operating plants requires an understanding of the factors that affect entrainment levels. Both chemical and operational influences are discussed in this paper. The difficulty of obtaining a representative sample makes it challenging to obtain an accurate measure of aqueous entrainment from a continuous process like SX. Coalescing devices used to get a more precise measurement of A-in-O entrainment are useful to complete mass balances around the SX circuits. Alternatively, mass balances can be used to estimate aqueous entrainments and are helpful as a tool to troubleshoot operations with a view to improving plant performance."

Jan 1, 2016

By S. Kahraman

P-wave velocity measurements were carried out on 22 large limestone blocks in a stone processing plant. In the laboratory, P-wave velocity of core samples was measured to obtain intact rock velocity. The square root of the ratio of the velocity of the large stone block to the velocity of the core specimen was called the velocity ratio index (VRI) and a quality classification for large building stones was suggested. In addition, the applicability of the established classification to stone cutting with gang saws was checked. It was concluded that the quality classification and estimation of slab production efficiency of the building stones can easily be made by ultrasonic measurements. However, the study was carried out only in limestone. Further study must be conducted to check the validity of the obtained results for the other rock types.

Jan 1, 2007

By I. J. Barker

This paper argues that the scale up of furnaces and the supply of electricity are going to be two major issues that will affect the ferro-alloy industry in the near future, and that economic factors will drive this development. The most common type of furnace for producing ferroalloys at present is the submerged-arc furnace with three electrodes, fed from a three-phase AC electrical supply. The scale up of this technology has now reached a fundamental constraint, which is caused by the electrical reactance of the secondary circuit. If the economy of any further scale up is to be achieved in the future then a different technology will have to be used. The supply of electrical power in future is likely to become amore complex issue than it is at present. Existing submerged-arc furnaces tend to run at fairly steady loads, but the ability to swing the load under demand-side management may offer advantages, and may allow a furnace to obtain cheaper power from the organizations that supply this power. This will have to be counterbalanced against the nuisance factors incurred by having a varying load in the operation of the furnace. Various options are therefore discussed in this paper. The possibility of scale up of Søderberg electrodes is discussed, as well as the use of DC power and multiple electrodes. Some of the issues with load swinging are also examined. A particular scenario is also briefly presented to show that considerable further scale up of ferro-alloy furnaces is still possible.

Jan 1, 2011

By J. A. Maritz

Since the dawn of mining, pillars have been used as primary support to ensure stable workings. Early designs were based on trial and error, after which more scientific means developed over time. A vast amount of progress has been made, especially in soft-rock room-and-pillar design methodologies, from which hard-rock design theories developed with minor changes to constant parameter values. The commonly used Hedley and Grant method for hard rock and Salamon and Munro methodology for soft rock draw on the tributary area associated with the pillar, the width-toheight ratio of the pillar, and a back-analysed strength reduction factor. In these methods, only the vertical stress, or stress normal to the pillar influences the load applied to the pillar. This investigation considers the possible influence of shear stresses on pillars in a room-and-pillar layout in single reef planes and multi-reef environments, based on elastic numerical modelling methods. The possible shear stress poses a safety and financial risk to the design process, whereby an undersized pillar would lead to unstable working conditions, whereas oversized pillars could lead to an under-utilized ore resource.

Jan 1, 2014

COUNCIL FOR 1990/91 President H.G. Mosenthal President Elect RD. Beck Senior J.P. Hoffman Vice Presidents Junior Or H. Scott-Russell Immediate Past President Or O.K.H. Steffen Honorary Treasurer OrH. Wagner

Jan 1, 1991

By P. J. Kinver

The paper presents details of the costs and outputs being achieved by South African mechanized tunneling and stoping drillings. The information was gathered from various hard-rock mining and tunneling operations ranging from deep-level gold mines to shallow base-metal mines. The survey included older pneumatic rigs and the newer electro-hydraulic rigs, but excluded shaft drilling and the stope drillings that were developed recently for narrow reefs. The information presented is intended as a guide to those having to decide whether to use mechanized drillings and, if so, what type and quantity

Jan 1, 1990

By B. J. Ralph, I. J. Corrans, B. Harris

In the first section, a brief background to the practical and theoretical aspects of bacterial leaching is presented. Descriptions are given of present and potential methods for exploiting bacterial leaching in metal-winning. In the second section, the results of recent research are presented. The aim of this work was to obtain a greater understanding of the mechanism of bacterial leaching of sulphide minerals. Bacteria were observed to catalyse leaching reactions by oxidising ferrous ions to ferric ions, by removing protective films at the mineral surface and by depolarising cathodic areas.

NIM reports Report no. 1845 The composition and mode of occurrence of gold in Witwatersrand ores and leach residues", Report no. 1861 The determination of some impurities in zirconium metal by instrumental neutronactivation analysis. Report no. 12 Exploratory tests on the concentration of tin ore from Kuils River, C.P. (29th Apr., 1966; re-issued Aug. 1976). Report no. 286 A mineralogical and petrographic study of the pre- Transvaal rocks in Borehole K.l, Koster district, western Transvaal. (15th Feb., 1966; re-issued Jun. 1976). Report no. 938 Life test on IRA 400 resin during the recovery of zinc chloride. (27th Mar., 1970; reissued Aug. 1976). Report no. 1010 The leaching, with hydrofluoric acid, of materials containing tantalum and niobium. (8th Jul., 1970; reissued Aug. 1976).

Jan 12, 1976

By P. Geldenhuys, D. J. C. Taylor, D. C. Page

This paper gives a technical review of the history, occurrence, mining, and metallurgy of iron in South Africa. The reserves of iron ore worldwide and in South Africa are reviewed, and potential new developments In the iron-and-steel industry in South Africa are examined. The paper concludes that the exploitation of lower-grade iron deposits will probably supplement the reserves of high-grade hematite ore in the distant future, and that, accepting this scenario. South Africa will be well placed to provide iron ore for its expected internal steel requirements, as well as supplying quality Iron ore for the export market.

Jan 1, 1988

New Journals The following three journals may be of interest to readers: Fuel Processing Technology, Process Economics International, Speculations in Science and Technology, MM reports Report no. 2016 Analysis of the NIMROC reference samples for majorelements. Report no. 2018 Supergene aUeration of sulphide ores. II. The effect on the floatability of chalcopyrite, galena, and sphalerite. Report no. 2013 List of unrestricted NI M publications issued from 1966 to 1979. Report no. 2014 The determination by spark-source mass spectrometry, of chlorine and phosphorus in high-purity tungstic oxide. Report no. 2017 Vanadium-bearing titaniferous iron ores from the Rooiwater, Usushwana, Mambula, Kaffirskraal, and Trompsburg Igneous Complexes. Report no. 2022 The determination of thallium and indium in sulphide concentrates. Report no. 2023 Atomic-absorption spectrophotometry with hydride generation: an improved technique. Proceedings Proceedings of the Eleventh Commonwealth Mining and Metallurgical Congress, Hong Kong, 1978. London, Institution of Mining and Metallurgy, 1979. 800 pp. 35,00 or $U.S.77,00.

Jan 1, 1979