Search Documents

By Jan Wolf

The iron ore industry presently utilizes two types of de-posits. The first are the high grade deposits generally located in remote areas and, secondly, the low grade de-posits which are normally found nearer to the steel-making centers. The high grade deposits produce a direct shipping ore which has an iron content which may be close to the maxi-mum 70% of Fe. These deposits have reserves which are ex-pressed in billions of tons. The ore needs little or no up-grading and where this is performed is restricted to ore washing. With the large demand for iron ore pellets, plus a national drive to perform as much of the upgrading as possible in the native country, there is a trend to erecting pellet plants at the mine location~ Large iron ore suppliers such as Australia, Brazil, Venezuela and Liberia already have pellet plants in operation, and there are new plants projected or expansion projects under study. The low grade ores are mined at locations closer to steel mills such as in Minnesota, Michigan and Canada. These low grade ores require methods of beneficiation to obtain a commercially accept-able product with the modern beneficiation techniques it is no~, possible to produce iron ore pellets of 68% Fe and 4.5% silica from ores containing as low as 26% Fe. Figure 1 gives a general picture of the types of iron ores and their beneficiation. The final product of the high grade ore is a coarse concentrate, sinter product or pellets. The final product of the low grade ores is pellets and, in some cases, coarse concentrates.

Jan 1, 1971

A knowledge of airway friction factor (K-factor) is necessary to designing mine ventilation systems for least cost and optimum effectiveness. The friction factor used must be accurate and reliable to estimate correctly roadway resistances and pressure sources for required flows. Though the resistance to flow offered by mine airways has been an object of study over the last half century, no accurate relation has yet been established from which the prediction of the resistance of a projected airway can be made. In Kentucky, only limited and incomplete data on local K-factors are available. Therefore, there is a need for field investigations to determine these values in-situ for existing mining conditions. The author describes a study concerning K-factor that was carried out in ten coal mines, located in eastern and western Kentucky. The results of these investigations are presented in both tabular and graphical form.

Jan 1, 1991

By S. G. Malghan, J. P. Van Dillen

Introduction Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined. HGMS of Uranium Ores The mechanism by which uranium minerals are attracted to a magnetic field is either due to its magnetic susceptibility or its association with other minerals that are magnetic. Data on magnetic susceptibility of uranium minerals are scarce. The only reported data are for uraninite at 2360 X 10-6 cm3/mole. Povarennykh (Andres, 1976) concluded that the magnetic properties of minerals depend on: • Structure of the outer electron shell in a mineral with electropositive atoms; • Valence of the atoms; • State of the chemical bonds; • Type of coordination; and • Proportion of magnetic atoms (Fe, Mn, Cr, and Ni) in the composition of the mineral. However, information on the magnetic susceptibilities of the constituent atoms of a mineral alone does not suffice for evaluating the mineral compound as a whole. Most often, uranium minerals can be beneficiated by HGMS if they are associated with other minerals that are magnetic. This appears to be a more predominant mechanism by which the uranium minerals are beneficiated. Experimental A Sala-HGMS (Malghan and Subramanian, 1981), model 10-15-20, separator was used in the experiments. The matrix material-ferromagnetic stainless steel in the form of expanded metal or steel wool-was packed into a 38-mm (1.5-in.) diameter by 360-mm (14-in.) long canister. The matrix material occupied only a 150-mm (6-in.) length. The experimental set-up and slurry flow direction are described elsewhere (lannicelli, 1976). The response of uranium ores in the HGMS was studied by feeding well-dispersed slurry at 10% solids and examining the influence of process variables on selectivity and overall uranium recovery. The chemical and mineralogical characteristics of the ores under study are presented in Table 1.

Jan 12, 1983

By Y. Breau, F. Robichaud

The Expert System implemented at the East-Malartic mill controls a copper flotation circuit while taking into account the profitability of the operation. Treating a copper gold ore, the flow sheet integrates a flotation step followed by cyanide leach circuit. The Expert System calculates the actual net smelter revenue of the flotation circuit, accounts for the operating cost of the cyanidation circuit and defines optimal metallurgical operating targets to optimize the overall economics. To be realistic, probability factors and circuit diagnostic analysis are integrated in the operating target selection. The Expert System has proved to be successful, robust and flexible. It resulted in a copper concentrate grade increase of 1% while maintaining recovery. The use of the expert system also gives plant personnel good training procedures and promotes interaction with mill operator.

Jan 1, 2002

By T. Tamagawa

A gaseous chlorination process for hydrometallurgical treatment of a chalcopyrite concentrate was investigated. The overall process is visualized to consist of low temperature chlorination-selective oxidation, followed by aqueous chloride leaching and SX-EW for producing electrolytic copper, elemental sulfur and ferric oxide. In this article, the chlorination phase of the processes is described. Initially, the chlorination behavior of chalcopyrite-concentrate micro-pellets was investigated using a small batch-type fluidized bed reactor. The optimum conditions thereby established was used in continuous chlorination tests. The chlorinated products thus prepared were used in the selective oxidation phase of the investigation.

Jan 1, 1999

By H. K. Lin

The effect of metallic iron fines on froth flotation of a sulfide ore was examined by comparing the flotation results with and without iron fines present in the flotation feed. Mild steel and ceramic laboratory ball mills were used to grind 600 g sulfide ore charges. The mild steel ball mill generated approximately 4.6 g of iron fines (0.8% of the ore charge mass) when grinding to a product size of 80% passing 200 mesh (75 mm). When a low dosage of a weak xanthate collector was used in flotation, the impact of the iron fines on sulfide flotation was marked. Higher dosages of stronger xanthate collectors rendered the impact of the iron fines much less significant. Consumption of the collectors by the powdery iron fines is believed to cause the differences observed in the flotation results. A galvanic effect on flotation was not evident in this study. The impact of the iron fines on silicates depression was also examined.

Jan 1, 2008

By Gordon B. French, Donald E. Garrett

INTRODUCTION Crude oil reserves in the United States are still very large, even though for many years they have not been sufficient to supply our entire domestic requirements. They are continuously being depleted as oil is pumped from the ground, but new discoveries and improved secondary and tertiary recovery methods are helping to reduce the rate of depletion. It is thus a slowly diminishing resource, but even as it is being consumed, immense reserves of oil are left behind as the so called "un-recoverable" portion of petroleum formations. Most oil fields can only obtain a 15 to 40% recovery of the original reservoir, and it is widely quoted that there are still about 300 billion barrels of this un-recoverable oil still in place (Mauch, 1980, etc.). With the present comparatively high oil prices, and the possibility of even higher future prices and short supply, this oil becomes an interesting potential reserve. Mining the petroleum formation would be one means of recovering at least a portion of this oil. The concept of oil mining is neither new nor limited to conventional oil fields, since the procedure could be equally employed with the otherwise difficult to produce heavy oil deposits, and the solid or semi-solid tar sands and diatomaceous hydrocarbon formations. Estimates place the U.S. tar sand resource at about 30 billion barrels, and heavy oil at 5-10 billion barrels (Unitar, 1982). Figure 1 graphically summarizes the heavy oil reserves based upon formation depth and characteristics, while Figure 2 shows their location. It is apparent that the preponderance of reserves are in California and Texas, but that they also occur in many other states. The major companies engaged in oil recovery from the heavy

Jan 1, 1983

By E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. This is especially true in surface and underground coal and stone mining where large, noisy equipment predominate. Workers in coal preparation and stone processing plants have also been found to be subject to high sound levels that could potentially cause NIHL over prolonged periods of exposure. National Institute for Occupational Safety and Health (NIOSH) researchers have been conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by river dredging. Little is known about the noise environment and worker exposures in these environments, where processing and mining equipment similar to coal and stone are employed. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to identify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges, in several surface mine sand and gravel operations and in the processing facilities. The locations where workers are likely to be overexposed and were found to be most susceptible to noise overexposures are reported. Results indicate that there are areas on the dredges (crane, suction pumps, and diesel engines) where sound levels greater than 90 dB(A) are present. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration (MSHA) Permissible Exposure Level (PEL) of 90 dB(A) TWA8, laborers, mechanics, oilers, helpers, pickers, and greasers are the workers likely to be exposed to hazardous sound levels and thus develop NIHL over time. Knowledge of the equipment noise, area sound levels, and worker dose levels is information that management and employees can use to reduce exposures. Exposures can be reduced in certain areas through administrative controls and through engineering controls applied to the noisiest equipment.

Jan 1, 2008

By R. H. King

Suboleski and King (1990) analyzed the reasons for the dramatic increase in underground coal mine productivity during the last 10 years. This paper examines whether this increase can be extended. The paper forecasts whether the mix of technological, procedural and other factors that produced the increase will change in the future. The forecast is based on the base case and spreadsheet production model described in the previous paper.

Jan 1, 1991

By Harvey W. Parker

Our industry has developed to the skilled, experienced and productive industry that we now enjoy as a result of the visions of great engineers throughout history, but, in particular for their visions in the last 1 centuries. Unfortunately for our forefathers, the technology lagged so far behind that these exceptional visions could not be realized for decades, sometimes for a century. All that has changed in recent time and many bold and visionary projects can now be constructed and operated because of dramatic advances in technology. Before, say, 1950, tunnel technology developed very slowly. However, technology is now developing at such a fast rate that planners and decision makers are challenged to stay ahead. Moreover, new technology will develop during the lifetime of any project that can dramatically improve under-ground space projects. One of the best examples of this technological advancement is that of closed-face TBMs which now make tunneling feasible in previously impossible ground conditions. Since it usually takes a decade or more to plan, overcome environmental and political issues, construct, and put into service major projects, planners and designers are challenged by the changes in technology that occurs during the long time span of planning and construction. This is particularly true of large infrastructure projects such as transportation, water and wastewater systems and other major underground schemes. Also, since the serviceable life of many of these tunnels is often over one century, planners must consider not only lessons learned from the past but also what new concepts and innovations may develop over an extremely long time. These and other issues create a great challenge to planners and illustrate the great importance of careful but creative vision and flexibility during planning of long-term tunnel and underground space projects.

Jan 1, 2008

By W. G. Pariseau

Introduction Caverns of 50 m in linear dimension at depths below 2300 m with a life of more than 25 years are proposed for the next generation of water-filled neutrino detectors. Little precedent exists for excavations in such an extreme environment, although some guidance is available from mining experience at great depths, for example, in South Africa, in Canada and at the former Homestake Mine in the U.S.A. Unlike mining for ore, there are choices available in the construction of such caverns that may mean the difference between success and failure. These choices should be informed by rock engineering principles. Recently proposed guidelines for orientation of brick-shaped caverns where the long dimension is a small multiple of the short dimension indicate that the most favorable orientation is with the long and short dimensions parallel to major and minor preexcavation principal stresses (Pariseau, 2005). Numerical analyses at reduced strength indicate some yielding at cavern walls should be expected but that an equilibrium state is quite possible and is aided by arching the back into a spherical dome when the cavern is an empty cylinder (Tesarik and others, 2002). The same indications of stability occur with brick-shaped caverns. However, the most dangerous situation occurs during the excavation sequence to final cavern dimensions. There are any number of excavation sequences that lead to the same final cavern shape, so there is an opportunity to partially optimize the sequence with construction guidelines that minimize peak stress concentrations during construction. This contribution discusses three practical excavation sequences that lead to the same brick-shaped cavern in the strong, massive Yates formation at the Homestake Mine where considerable rock mechanics data has accumulated through the years(e.g., Pariseau, 1985, Pariseau and others, 1995) and where actual mining on the 8000 Level indicates a strong possibility of successful investment in the next generation of large, deep neutrino detectors. The main results are: (1) a favorable brick-shape is one with dimensions in the same proportion as the preexcavation principal stresses (compressionpositive), and (2) favorable orientation of the most extreme but temporary shape of excavation is also best for the construction sequence. Analysis results from a mix of Homestake Mine data and possible excavation geometry illustrate the advantages of these guidelines.

Jan 1, 2006

By Arnold Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970?s. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator?s area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator?s hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009

By M. J. Farrell

Mining is a significant emitter of greenhouse gases and is the focus of increasing attention from green groups and regulators. Miners need to know their own carbon emissions and how they compare with the rest of the industry. Miners and mining companies need to know where they fit in the emissions curve. Who is in the bottom quartile? This article is based on research report data from minecost.com and Metalytics Pty Ltd which detail the specific carbon dioxide emissions for 208mines producing 90% or more of western world copper, zinc, lead and nickel in 2007. The copper and nickel mines also include Norilsk in Russia, KGHM in Poland and Kazakhmys in Kazakhstan. This is the first time that such information has become available.

Jan 1, 2009

By M. E. Smith

Waste rock dumps, tailings impoundments and spent leach heaps are common features at mine sites. Many of these waste disposal facilities contain sulfide-rich minerals, which generate acid mine drainage (AMD) when they oxidize. Control of AMD can be achieved by removing one or more of the three essential components in the acid-generating process (sulfides, air, or water). One AMD prevention measure is to cap the waste with an engineered cover system to minimize the infiltration of water and diffusion of air into the system. Possible cover designs include: ? Earthen ?store-and-release? covers (also known as evapotranspiration (ET) or water balance covers), including capillary barriers. These covers require climate conditions where there is both modest to little rainfall and significantly greater evapotranspiration than precipitation, both annually and seasonally. ? Low-permeability compacted clay liners (CCLs) employing fine-grained soils typically compacted at wet of optimum water content. ? Geosynthetic composite covers, comprised of a geomembrane liner placed over and in direct contact with either a CCL or a geosynthetic clay liner (GCL). These systems have been commonly used for base liners for leach pads as well as covers and base liners at municipal solid waste (MSW) landfills in the US for more than 20 years. Comparisons of these different cover systems, both in terms of performance and cost, are presented later in this paper. First, however, a review of the typical mine closure approaches, and the possible rationale behind them, is warranted.

Feb 27, 2013

By Martin Langenderfer, Catherine Johnson, Alexander Douglas

Mine haul roads degrade rapidly due to extreme loads on sub-optimal construction materials. Unmanned aerial vehicles (UAV) are suited to quantify large-area road-network conditions, such as surface roughness, defects, and grade to optimize remediation of poor conditions and reduce overall costs. Mine haul roads present unique challenges, such as material type and edge characteristics, to automatic road detection that often fail, requiring manual road input. This research proposes a new method for analysis using the road center determined by principal curve analysis of a haul truck’s Global Navigation Satellite System (GNSS) traces; analysis grids were created from this center line. A dense point cloud from UAV photogrammetry was generated, and multiple linear regression analysis was conducted on each individual grid. The root mean square error in each grid indicates the surface roughness, and the change of slope between grids indicates the road grade inconsistencies. This method was applied to 26 road sections, and the results were validated by images taken from the truck operator’s vantage point. Critical defects were identified including excessive pothole formation, corrugation, depressions retaining water, and narrowing of travel lane. The results demonstrate this is a valid method of road identification and quantification of road defects at a mine site.

Dec 19, 2023

By R. L. Grayson, J. R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. Thus far environmental groups remain unconvinced, and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This paper presents a fresh and cogent perspective on coal’s role in sustaining society by anchoring the message in a transparent material flow analysis that links coal’s impacts across a broad range of social and environmental aspects.

Jan 1, 2006

By E. Piesch, M. Urban, G. M. Hassib

INTRODUCTION In radon dosimetry diffusion chambers with passive [a]-detectors are now in current use to investigate the long-term accumulated indoor exposure of radon and daughters. For the diffusion chamber developed at Karlsruhe the electrochemical etching technique (ECE) was applied to reveal [a]-particles in polycarbonate plastic detectors. Compared to conventional etching, the main advantages of the ECE are the large track diameter, simple track counting in a single field of about 1 cm2, stability of the latent tracks to humidity and temperature and ability for a long-term accumulation up to 1 year. The electrochemical etching system was designed to etch in one run about 101 foils by using a 200 W high voltage generator. The commercial available radon dosimeter system is applied for a country wide program of measuring radon in dwellings. Because of an increasing interest of radon monitoring in mines, environmental monitoring and personnel dosimetry the properties of several track etch detectors have been studied. In the comparative study, Makrofol E, LR 115 and CR 39 were used in the diffusion chamber to investigate the etching techniques, the relative efficiency, the measurable [a]-energy range, and the counting statistic for the measurement of radon concentration. THE KARLSRUHE DIFFUSION CHAMBER The design of the Karlsruhe diffusion chamber is presented in Fig. 1. The upper part of the chamber is closed by a fibreglass filter to separate radon from aerosols, heavy dust particles and radon decay products. Inside the diffusion chamber [a]-particles from radon and daughters are detected by two passive radon detectors, one on the bottom of the chamber and the other in front of the filter. With the fibreglass filter applied the diffusion time is about 1 minute for radon. Therefore, also short-term variations in the radon concentration are recorded by the track detector. Mainly because of the short halflife of thoron (56 s) only about 7 % of the thoron concentration is expected in the diffusion chamber. Radon monitoring provides the estimation of the long-term accumulated mean value of the radon concentration with a lowest detectable concentration of 0.1 pCi/1 after 3 months accumulation by using polycarbonate track etch detectors, an electrochemical etching technique and track counting in a single field of 1 cm2. The diffusion chamber was optimized for the polycarbonate track detector with respect to chamber geometry and detector position [1]. Table 1 presents data for 3 different diffusion chamber designs. The radon sensitivity of the diffusion chamber depends on the [a]-energy discrimination and the angular response of the [a]-track detector. The difference between foil No 2 and foil No 1 can be explained by an additional plate-out effect of radon daughters on foil No 3. The high sensitivity of foil No 3 compared to that of foil No 2 is caused by an increase of the effective volume and the effective area for [a]-particle from radon and from plated-out decay products, respectively. Additional experiments have been performed in order to investigate the electrostatic properties of the plastic material and the properties of the diffusion filter [1]. The properties of bare a-detectors were compared with those inside the diffusion chamber. In contrast to laboratory results, dust particles deposited on the detector surface or in the environment of the detector obviously affect the reproducibility of the bare detector significantly. After 4 months exposure in dwellings the scatter of 10 dosimeters exposed in the same room exceeds a factor of 3 compared to 15 % for the diffusion chamber. COMPARATIVE STUDY OF TRACK ETCH DETECTORS Detector types and evaluation technique In the comparative study the properties of the following plastic track etch detectors have been applied: - LR 115 from Kodak Pathé, France, is a red dyed cellulose nitrate layer of 13 µm thickness on a 100 µm thick polyester support. The holes appears as bright spots in a dark red background. In an optical microscope counting of through etched [a]-tracks which must penetrate the detector layer - CR 39 from Pershore, England, is an ally1 diglycol carbonate plastic of about 300 m thickness. The normal etched [a]-tracks are counted by an optical microscope and the ECE [a]-tracks by a microfiche reader.

Jan 1, 1981

By Richard A. Thomas, III JAMES H. ROWLAND, Liming Yuan

This paper presents the results of large-scale fire experiments on evaluating the performances of carbon monoxide (CO) and smoke sensors at low ventilation velocities. Experiments using three different combustibles — conveyor belt, coal and diesel fuel — were conducted in the experimental mine at the U.S. National Institute for Occupational Safety and Health (NIOSH) Bruceton Research Facility. A total of eight sensor stations were located downstream of the fire with each station containing sensors for CO, smoke, carbon dioxide (CO2 ), oxygen (O2 ), humidity, barometric pressure and temperature, as well as two airflow sensors. The airflow velocity ranged from 0.22 to 0.26 m/s (44 to 51 fpm) in the tests. The response times were recorded for the CO and smoke sensors at each sensor station when smoke and gaseous products of combustion from each burning combustible reached the station. The response times of the CO sensors were used to determine the appropriate sensor spacing in the belt entry with a low air velocity. The performance of the smoke sensor was found to be affected by the high humidity in the experiments. The results on proper selection of sensors and the determination of sensor spacing at a low ventilation velocity can be helpful for ensuring sufficient early fire warning for underground workers, thereby improving the health and safety of miners.

By Goran Mathisson

In several investigations the correlation has been studied between the fuel consumption and the reducibility of the charged material in the zone of indirect reduction in the blast furnace (1, 2, 3, 4, 5). It has been found that increased reducibility allows greater gas utilization which accordingly lowers the fuel consumption. In direct reduction units this relation has not yet been fully established partly owing to the lack of accurate test methods and experience with different materials as regards reducibility. However, since the production rate in a direct reduction unit is closely related to the time required to reach high degrees of reduction, the reducibility must be regarded as one of the most important properties of the material.

Jan 1, 1979

By L. Tercero Espinoza, F. Marscheider-Weidemann, C. Gandenberger

"A reliable supply of non-energy raw materials is a precondition for the functioning of the European economy. In line with its importance, the issue of raw materials supply has become more prominent in the past years, especially owing to turbulent raw material markets. However, these turbulences are not due to depletion of the geological resources but to a missmatch of (expected) supply and (expected) demand, with several interacting factors influencing the markets both from the supply as well as from the demand side. A recent evaluation, published in June 2010 within the framework of the EU Raw Materials Initiative, sought to bring together these two sides of raw material markets and asked the question "which raw materials are critical for the EU?" Herein we present the methodology used by the Ad-hoc Working Group on Defining Critical Raw Materials and the results obtained, complemented by results from the study "Raw Materials for Emerging Technologies"."

Jan 1, 2011