Search Documents

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay

"The Analysis of Retreat Mining Pillar Stability (ARMPS) program was developed by the National Institute for Occupational Safety and Health (NIOSH) to help the U.S. coal mining industry to design safe retreat room and pillar panels. ARMPS calculates the magnitude of the in-situ and mining-induced loads by using geometrical computations and empirical rules. In particular, the program uses the “abutment angle” concept in calculating the magnitude of the abutment load on pillars adjacent to a gob.In this paper, stress measurements from U.S. and Australian mines with different overburden geologies with varying hard rock percentages were back analyzed. The results of the analyses indicated that for depths less than 650 ft, the ARMPS empirical derivation of a 21° abutment angle was supported by the case histories; however, at depths greater than 650 ft, the abutment angle was found to be significantly less than 21°. In this paper, a new equation employing the panel width to overburden depth ratio is constructed for the calculation of accurate abutment angles for deeper mining cases.The new abutment angle equation was tested using both ARMPS2010 and LaModel for the entire case history database of ARMPS2010. The new abutment angle equation to estimate the magnitude of the mining-induced loads used together with the LaModel program was found to give good classification accuracies compared to ARMPS2010 for deep cover cases.INTRODUCTIONIn the early 1990s, the Analysis of Longwall Pillar Stability (ALPS) was introduced by Mark (1990) as a chain pillar design software and was generally accepted and used by the U.S. coal mining industry. Following the success of ALPS, the National Institute for Occupational Safety and Health (NIOSH) developed the Analysis of Retreat Mining Pillar Stability (ARMPS) program for designing retreat mining pillars using a similar approach as ALPS (Mark and Chase, 1997). The Australian mining industry also recognized the success of ALPS, and Colwell, Frith, and Mark (1999) calibrated the program to Australian conditions. The ALPS and ARMPS programs draw their strengths from the large databases that are used to calibrate them (Mark, 2009). However, following the Crandall Canyon Mine collapse in 2007, NIOSH had to reconsider the pillar design criteria used in deep-cover retreat mining (Mark, 2010). The ARMPS overburden load prediction algorithm was improved to more accurately predict the loading of narrow panels with high overburden depths by implementing the pressure arch concept, and this new version is called ARMPS2010."

Jan 1, 2019

By C. J. Hall

I would like to congratulate Professor Gershon on an idea that is obviously valuable and is certainly new to me. It has, however, to be further developed, in that one can get fallacious results by limiting oneself to positional weights. In the example problem, the positional weight of one block was 8.6 (the 8.0 value in the paper was incorrect) for 36 units in the cone, for a mean block value of 0.239. The positional weight of the second block was 4.4 for 15 units, for a mean block value of 0.293. Surely one would expect the second block to be rated higher. Additionally, the time value of money adjustment cannot be determined by depth, because the time that a block is mined is determined by the mining sequence, not depth. Figure 1 shows a slightly altered version of Professor Gershon's pit. The overall value of the pit is the same, as are the total values under each of his blocks. The values in the right-hand cone have been reversed top to bottom, and the values in the rest of the pit adjusted to keep the central cone total unchanged. All values have been multiplied by 10. Figure 2 shows the sequence of mining, at three blocks per year, for Professor Gershon's pit, and Fig. 3, the sequence for a pit under the other block. Table 1 shows the value and discounted value (15%) of Professor Gershon's pit, and Table 2 shows similar values for the second pit. It is apparent that the second pit schedule is more valuable than the first.

Jan 1, 1988

By Robert C. Pease

Siskon Gold has started gold production at the San Juan deposit in northern California. The mine is located about 27 km (17 miles) north of Nevada City, CA (Fig. 1). It is scheduled to be-come the largest underground gold mine in California. It is situated in the western foothills of the Sierra Nevada Mountains in the Mother Lode gold belt. The property consists of 8 km2 (2,000 acres) of patented land. It is situated in a topographically high area known as San Juan Ridge, which is 213 m (700 ft) above and between the Middle Yuba and South Yuba rivers. The elevation is between 790 and 914 m (2,600 and 3,000ft) above sea level. Annual precipitation averages 1,346mm (53 in.). Most of that falls between November and April.

Jan 1, 1996

By Dirk van Zvl

The design of cover systems for reclamation schemes in tailings requires estimation or determination of tailings materials properties such as compressibility, shear strength and consolidation characteristics. It is very difficult and expensive to obtain truly undisturbed tailings samples for laboratory testing. In situ testing methods have been developed for economically obtaining large amounts of information. Two of these methods are described, the piezocone and the flat plate dilatometer. Both of these methods provide a rapid means of detailed material identification in a nearly continuous fashion for the entire depth investigated. The equipment is described and typical data from a uranium tailings impoundment is presented. The results are compared and the advantages and disadvantages of these methods are discussed.

Jan 1, 1984

By S. Solar, G. Tiess, K. Nielsen, H. Wagner

The paper summarises the results of a recent study of minerals planning policies of the Member States of the EU. The study has shown that contrary to the public opinion the production of industrial minerals and construction minerals is significant the former accounting for about 20 percent of global production, the latter amounting to about 3 billion tonnes per annum. In contrast the importance of metal ores has diminished although metal production in some European countries can still be significant. The study revealed that very few Member States have clearly defined mineral policies. Common to most mineral policies is the emphasis on reducing minerals consumption and recycling whereas the important aspect protecting access to minerals resources is not adequately addressed by most policies. Access to mineral deposits is regulated in most Member States by land use legislation and administration. Information on mineral deposits in land use planning data bases tends to be scarce. This together with the absence of formal mineral policies places minerals at a disadvantage in land use decision making. The emergence in the recent past of environmental legislation and in particular environmental impact assessments has had a crucial effect on the duration of the authorization process for new mineral projects. Examples are given how minerals planning is handled in some of the Member States.

Jan 1, 2005

By S. Addie

In the early 1990’s the British Columbia (Canada) mineral industry frequently discussed the need to participate in, and compromise with, public environmental interests in order to ascertain long-term stability. However, as the decade progressed the mineral industry withdrew from almost all meaningful public participation. As government protected areas policy in the past year has illuminated, there is a continued need for long-term land access stability. This paper historically analyses the public engagement policies of the British Columbian mineral industry while it participated in long-term consensus-based multi-stakeholder land-use planning processes. From this analysis the paper recommends that the mineral industry reengage the public and institute a new working relationship with environmental advocacy groups so as to ensure British Columbia becomes the most sustainable mineral producing jurisdiction in the world.

Jan 1, 2011

By J. Weinstein

New erosion, corrosion resistant metal, ceramic, and polymer composite technologies are being developed and marketed by Alanx Products L.P. for use in hydrocyclones, pumps, valves, and other applications in mining and minerals processing. This paper will present an overview of the ceramic/metal composite material system and properties developed, which include excellent erosion/ corrosion resistance. Wear data will be shown from a variety of laboratory tests in dry and wet conditions, in aqueous neutral and corrosive environments. Comparisons will be made with a variety of competitive materials currently used in the industries sited. Data will also be presented on field tests with pumps and hydrocyclones in hard rock mining and other abrasive/corrosive environments. Field data from North and South America, as well as Australian mining applications will be highlighted.

Jan 1, 1992

By C. Don Sullivan

Paraphrasing the poetic repetition of Gertrude Stein - "Research is research, is research, is research --- ad infinitum." But research takes many forms and involves many facets. Perhaps the most simple of definitions is that attributed to the late "Boss" Kettering of General Motors who in advising a young trainee said, "Research is an intelligent effort to satisfy the curiosity of the human mind." Reclamation research is complex and requires a diversity of scientific knowledge. The overall aim of land reclamation research is directed to finding practical ways to develop efficient methods to restore mined lands to productive use, compatible with use of adjacent lands, as soon after mining as possible; and, finding practical ways to reduce or prevent damage to surrounding resource areas, which may be affected by the mining process. Research in the field of mined land reclamation is not entirely new, although in some respects we are exploring new areas each day.

Jan 1, 1967

By W. McMahon

Following the Sago Mine accident, the Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 1-ft resolution map of the mine to produce a 3-dimensional (3-D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3-D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals, and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling, and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jan 1, 2009

By James Paone

Drillability of rocks by mechanical means is closely related to the physical properties of the respective rocks, Various approaches by previous investigators on rock drillability are presented, as well as recent techniques studied by the Bureau of Mines. The studies show drillability concepts based on (1) theoretical drilling equations derived from laboratory drilling experiments extended to field drilling results and on (2) a statistical method where multiple regression analysis is used to develop a prediction equation for drillability.

Jan 1, 1966

By T. Lilley

The use of membranes in wastewater systems has increased rapidly in recent years. Microporous or semi-permeable barriers augment conventional chemical or biological processes to meet stringent treatment targets. These developments enable elegant solutions to wastewater discharge challenges and extend the scope of water recycle redressing the overall water balance and operational economics Wastewater treatment processes are discussed by reference to the spectrum of waterborne contaminants and the respective membrane separation capabilities. The role chemical pre-treatment to enable physical separation of metals with micro-filtration (MF) is described and how integration of MF with reverse osmosis (RO) is used to control a broader range of dissolved contaminants Membrane configurations are considered apropos function, operational economics and sustainability. These features are exemplified with case studies. Firstly, MF alone following chemical precipitation for the removal of heavy metals, then MF onto two stages RO of different configurations for TDS reduction and waste volume minimisation and finally an open channel RO alone for the reduction of inorganic COD from a leach stream.

Feb 27, 2013

By R. Bauer

Adaptations and redesign of the existing already very successful and proven road milling machine concept and technical innovations such as an optimized, specifically for mining application developed cutting drum, cutting housing design and cutting tools, high manoeuvrability achieved via a tight turning radius, a three disk clutch system and a cutting drum drive that allows for the acceptance of higher loads, a complete reinforcement of the chassis to withstand higher vibrations and torque, the installation of increased engine power via a modern drive unit, a specifically for mining/construction applications developed operator’s platform and finally a redesigned air intake system and the adaptation of the levelling system resulted in far more cost effective and advantageous capabilities of Wirtgen Surface Miner in soft to medium hard mining and construction applications. As the achieved results show for the first time in modern surface mining history mechanized cutting is capable to compete successfully against traditional drill, blast/ripping and other conventional mining methods.

Jan 1, 2007

By Y. Guan

The dissolution behavior of silver in ammoniacal solutions with cupric ammine as an oxidant has been investigated using a rotating disc electrode. The rates of dissolution of silver were determined by an electrochemical means as well as a direct measurement of silver ions reported in the bulk solution as a function of time. The variables investigated included stirring speed, temperature, concentration of lixiviants, and pH of the solutions. The rate of dissolution under the conditions studied' was found to be controlled by an electrochemical reaction at the liquid/ solid interface with an apparent activation energy of 48.07 kJ /mole. The rate was found to be a half order with respect to the, concentration of cupric tetra-ammine, Cu(NH3)l+.; The results were explained in terms of a mixed' potential theory.

Jan 1, 1994

By A. L. Mular

Steady-state material balances calculated from data measured at various locations around process units are useful for many purposes, such as metallurgical accounting, on-line control, and the development of mathematical models. Often it is possible to calculate material balances by several independent procedures when excess measurement information, i.e., redundant data, is available. Clearly, if the data were collected without measurement errors, a theoretical condition never found in practice, all material balances calculated from redundant data would be in agreement. The real situation is that error exists in practical measurements, so that the results of material balances determined from available optional procedures differ. Consequently, best fit computational procedures to improve the material balances by taking measurement errors into account have been formulated. Such procedures can be used also to judge whether measurements are grossly in error due to either faulty observations or defective data sensing devices. A variety of mathematical techniques are available which serve to adjust raw data. The adjusted data permit mass balancing that does not depend on the computational method. To illustrate the need for an adjustment procedure, Table 1 shows a raw data set acquired around the Brenda Mines Ltd. No. 4 grinding circuit shown schematically in Fig. 1. At least seven optional ways to calculate a circulating load ratio may be employed. These are shown in Table 2 where, depending upon the calculation [ ]

Jan 1, 1979

By M. E. Gershon

I would like to congratulate Professor Gershon on an idea that is obviously valuable and is certainly new to me. It has, however, to be further developed, in that one can get fallacious results by limiting oneself to positional weights. In the example problem, the positional weight of one block was 8.6 (the 8.0 value in the paper was incorrect) for 36 units in the cone, for a mean block value of 0.239. The positional weight of the second block was 4.4 for 15 units, for a mean block value of 0.293. Surely one would expect the second block to be rated higher. Additionally, the time value of money adjustment cannot be determined by depth, because the time that a block is mined is determined by the mining sequence, not depth. Figure 1 shows a slightly altered version of Professor Gershon’s pit. The overall value of the pit is the same, as are the total values under each of his blocks. The values in the right-hand cone have been reversed top to bottom, and the values in the rest of the pit adjusted to keep the central cone total unchanged. All values have been multiplied by 10. Figure 2 shows the sequence of mining, at three blocks per year, for Professor Gershon’s pit, and Fig. 3, the sequence for a pit under the other block. Table 1 shows the value and discounted value (157. ) of Professor Gershon’s pit, and Table 2 shows similar values for the second pit. It is apparent that the second pit schedule is more valuable than the first.

Jan 12, 1987

By S. Acar

The results obtained for the selective flocculation or flotation of natural ores do not usually agree with the corresponding properties of the constituent minerals when present alone. This is mainly due to the presence of dissolved mineral species which can interact in many ways with other components in the system and alter their behavior. In this paper, the effect of dissolved species on the flocculation and electrokinetic properties of sulfide minerals is disscussed. Dissolved Fe, Cu and Ni species are found to affect the properties of chalcopyrite, pentlandite, millerite, pyrrhotite and covellite in certain pH range. These effects are interpreted in terms of species adsorption leading to activation or depression of reagents, surface precipitation and complexation of species, etc.

Jan 1, 1985

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and thus deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the go band to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Feb 27, 2013

Cripple Creek and Victor Gold Mine is an epithermal gold deposit located in the Rocky Mountains of Colorado. Surface operations are continuing along with an expansion for an onsite mill to take place in the next couple of years. The surface pit is currently progressing downward from an oxidized zone into a transitional, more sulfide/ telluride-rich zone. Gold mineralization includes native gold, electrum, and tellurides. Cyanide heap leaching is the recovery process for the oxidized ore with the sulfide/telluride-rich ore to be processed at the new onsite mill. Ore characterization prior to mining is vital when there are two possible recovery processes. This characterization is dependent on geometallurgy. To identify the causes of the variability, multiple parameters are analyzed and assayed. These parameters are measured by a variety of analytical testwork. The analytical testwork provides measurements for the desired parameters. Geometallurgical models are developed for the parameters per recovery process, so estimations can be inserted into the resource model to optimize operations and recoveries.

Feb 27, 2013

By S. Bhattacharaya, S. Aich, B. K. Nandi

"At present scenario, there has been an increasing demand in the usage of blend coal in power sector; regardless of how, specific knowledge on burning and ignition characteristics and their interactive effects is stingy. In this work a detailed investigation was therefore taken up to study in detail the combustion characteristics of selected coal samples and their blends. Certain parameters were believed to have significant effects on combustion characteristics of individual coal and their blend. Major parameters identified for this purpose included proximate analysis, combustion conditions, heating rate, reaction regions, blending ratios, ignition condition, reactivity (or reaction rate) and burnout temperatures. With the help of these parameters, thermal features and reaction kinetics of the individual and blended samples were investigated through a qualitative and quantitative thermo-gravimetric analysis of two different individual coals and their blend carried out in an oxygen atmosphere from ambient to 800 0C at a constant heating rate of 10 K/min. A significant difference in terms of rate of mass loss with temperature correlated from Arrhenius expression along with coal-coal blend interactions and deviation from their expected behaviour, have been observed between the kinetics of individual and blend samples, the latter showing better ignition performance and comprehensive combustion phase. It was also found that particles having the lowest percentages of volatile matter and ash could possibly be blended with particles having high ash and volatile matter to meet the required burning condition which can be effective in terms of cost savings, improved fuel economy, reduced undesirable exhaust emissions and improved safety of coal burning equipment. Experimental results further indicated that individual samples and coal blend samples have different combustion features in terms of residue left, peak temperatures and activation energies. Thermodynamic activation parameters such as activation energy, pre-exponential factor and order of reaction were computed from the thermal data using the modified form of non-isothermal methods. INTRODUCTION Coal has been the most significant source of energy for India and would remain so at least for the next few decades. About 60-65% of the electricity produced in India is from coal fired power plants. Indian coal is of drift origin and of high ash content. Ash content of the coal burnt in power plants in India is in the range of 30-45%, most of it being Run-of-Mine coal. Most of the power plants in India source their coal from number of mines, most common being multiple sourcing. Usually coal from each source [1] is burnt separately. For various reasons mostly associated with logistics, burning of blended coal is rarely practiced. Blending of coal is practised mainly for improving the quality of available coal and meets the shortage of coal supply. Blending technique is generally practised in power industries to reduce the cost of power generation along with mitigating combustion performance or slagging problem ensuring consistency in as fired coal quality and also for environmental compliance. Blending good quality imported coal can improve coal quality and helps in preserving indigenous coal resources for longer period [2]. Use of blended coal shall reduce load on all boiler components (Mill, CHP, Boiler, AHP) & reduce O&M cost and increase the availability. The main purpose of blending is to get a blended as fired coal having ash, volatile matter and gross calorific value close to design coal and the two coals are to be blended in such ratio proportions that resultant coal blend have desired ash, volatile matter and gross calorific value [3]. For a coal to be blended certain parameters have to be considered to get compatibility with respect to combustibility ( Burn ability) of coal, grindability ( HGI), ash fusion behavior, swelling characteristics of coal, need to be checked"

Jan 1, 2017

By Satya Harpalani

The four most important parameters controlling the flow of gas in coal are the gas content, permeability, diffusion coefficient and cleat characteristics. Estimates of these and, more importantly, a knowledge about the variation in their values over time are required for simulation of long-term gas production. This paper describes experimental techniques to determine each of these, along with their time dependency, under simulated in situ conditions. It is shown that the permeability, diffusion coefficient and the cleat aperture values are not constant as usually assumed to be. There is a significant variation in their values as a result of changes in the microstructure of coal associated with release and flow of gas.

Jan 1, 1995