Search Documents

By G. Mei

"This study explores froth flotation and selective flocculation methods to recycle waste phosphors containing several rare earth elements, namely, yttrium (Y), europium (Eu), cerium (Ce) and terbium (Tb). The effects of the presence or absence of collector and of flocculant and their dosages, as well as the pH, were investigated. Reverse flotation resulted in concentrates with grade of 27.03 percent and recovery rate of 71.36 percent, while flocculation resulted in concentrates with grade of 31.43 percent and recovery rate of 91.28 percent. The flotation and flocculation behaviors were further analyzed by X-ray diffraction analysis, zeta potential measurements, particle size distribution and other methods. The successful separation of rare earth minerals by flotation was attributed to the selective adsorption of the collector onto quartz, making it particularly recoverable by reverse flotation so as to be separated from the valuable materials. The analysis of the particle aggregation process indicated that its better flocculation performance was due to the selective adsorption of flocculants onto the unwanted materials, enlarging the flocculant sizes by forming aggregations and facilitating the separation of rare earth minerals from waste materials based on different settling rates. IntroductionBecause waste phosphors pose the problems of heavy environmental burden and high risk to human health (Hu and Cheng, 2012) as a result of containing heavy metals such as mercury and manganese (He et al., 2006; Lucas and Emery, 2006), they have received added attention as urban mining resources for extracting rare earth elements (REEs) like yttrium (Y), europium (Eu), cerium (Ce) and terbium (Tb).At present, chemical processes such as acid leaching, alkali fusion, roasting and extraction are the primary methods for recovering REEs from waste phosphors (De Michelis et al., 2011; Li et al., 2012; Li, 2010). With these strategies, phosphors can be effectively decomposed and their REEs extracted. After the removal of impurities, the REEs can be efficiently precipitated by adding an H2C2O4 solution (Porob et al., 2012). Although relatively high recovery rates are achieved, those processes entail high energy consumption and can cause severe environmental pollution."

Jan 1, 2017

By W. Roggenthen, Z. J. Hladysz, G. D. Callahan, W. G. Pariseau, W. Weinig, C. Randolph-Loar, R. Popielak

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, SD, under the sponsorship of the U.S. National Science Foundation (NSF) in cooperation with the Department of Energy (DOE). This national facility will host a variety of multidisciplinary science and engineering experiments, including physics experiments that require shielding from cosmogenic radiation. Current plans include construction of large rooms (up to 55 m in width) at depths of 1.48 km (4,850 ft) and 2.25 km (7,400 ft) below the surface. Preparation of the preliminary design required the development of a geotechnical characterization program, including preliminary drilling and coring, core logging, drill hole mapping with a televiewer, drift mapping of the geology and rock structure, in situ stress measurements, and laboratory testing of the mechanical properties of the rocks and discontinuities. Overall rock quality is very good to excellent. Site investigations included geotechnical assessments for the construction of caverns and laboratory modules. The results are favorable and reaffirm selection of the Homestake site for establishment of a Deep Underground Engineering and Science Laboratory.

Jan 1, 2011

By Min Chen, Qinghua Liang, Weishan Yan, Yuan Feng, Shigang Wang

Various coal mine robots (CMRs) and unmanned aerial vehicles (UAVs) are implemented to explore unknown mines for improving the safety and efficiency of mining. It is challenging for CMRs and UAVs to achieve accurate positioning due to the absence of GPS, poor lighting conditions, and similar geometric features in complex mine scenes. LiDAR-based localization and mapping methods are admittedly more accurate than others, while long-time running in large-scale scenarios will also introduce non-negligible cumulative errors. This study presents a semantic-aided LiDAR simultaneous localization and mapping (SLAM) with loop closure, which leverages the uniqueness of mine intersection structure to establish stable semantic loop closure. Specifically, we propose a semantic intersection descriptor of translation and rotation invariance, which encodes 3D point clouds of the same intersection from different positions and viewpoints into a unified image. By using the semantic descriptor, we can construct a constant loop constraint when the same intersection is revisited from different directions to reduce cumulative drift. We provide experimental validation using large datasets collected in two large underground mines, namely, a simulated Edgar mine deployed in ROS Gazebo and a public underground mine dataset provided by ETH. Experimental results show that the proposed method has higher localization accuracy and outperforms the existing LiDAR-based SLAM strategies.

Aug 10, 2023

By Andrew W. Jenike

The first significant studies of problems related to the handling and storage of bulk solids were reported at the end of the nineteenth century. Early work originated from the necessity to store large quantities of grain and was concerned mainly with pressures affecting the structural design of silos and bins. The Janssen formula (about 1898) and the work of Ketchum [1] form the highlights of that period. In more recent years, progress in mechanization, increasing plant capacities, and rising costs of labor have focused the attention of engineers on the problem of gravity flow of bulk solids. A great deal of work has been done with models, and flow patterns obtained in small scale bins have been described in several publications, for example [2, 3]. An attempt to develop a theory of flow of bulk solids was reported in 1954 [4, 5, 61 and presented to the in a paper [7] in the same year. AIME recommended the continuation of this work and, as a result, Engineering Foundation granted a sum of money to set up a Bulk Solids Flow Laboratory. Two and a half years ago the project gained the support of the University of Utah and a laboratory was set up on the campus of the University. This project is now in progress, it has received the support of the American Iron and Steel Institute and of Kaiser Engineers, Division of Henry J. Kaiser Company. The results obtained to date are summarized in this report.

Jan 1, 1959

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

2.1 INTRODUCTION When total extraction of an opening of sufficient size is reached in a horizontal coal seam, the roof strata in the overburden deform continuously to reach a new equilibrium condition. The severity of deformation decreases upward toward the surface. As the downward saggings of the strata propagate and reach the surface, there will be a depression zone on the surface directly above, but extending beyond the edges of the underground opening. This is the surface subsidence basin or surface subsidence trough. The surface subsidence basin is circular in plan view, if the coal seam is horizontal and the mined-out opening is square in shape. But it is rectangular with rounded corners or elliptical if the coal seam is horizontal and the mined-out opening is a long- and thin rectangle or a short-rectangular, respectively (Fig. 2.1). Most underground openings (e.g., longwall panel) assume rectangular shape when total extraction has been completed. Theoretically the edges of the subsidence basin are the points of zero subsidence. But it is difficult to exactly locate the points of zero subsidence. Therefore in practice the points with vertical subsidence of 0.4 in. (10 mm) are used. The final subsidence basin is that which exists long after the mining has been completed, because its magnitude and shape are quite different from the dynamic subsidence basin formed while the face is moving. 2.2 CHARACTERISTICS AND TYPES OF DEFORMATION IN THE FINAL SUBSIDENCE BASIN For a horizontal coal seam, every point in the subsidence basin moves toward the center of the basin. Subsidence is maximum at the center of the basin. Any cross-section that passes through the point of maximum subsidence and either parallel to AB or CD line (Fig. 2.1) is a major cross-section along which principal directions of surface movements occur. However among those infinite numbers of major cross-sections, two specific ones are of special significance, not only because the magnitudes of surface movements are the largest, but also because they are the most easily identifiable directions, i.e., one that is parallel to the faceline at the center of the basin (CD in Fig. 2.1) and' the other is that perpendicular to the faceline but parallel to the diction of face advance (AB in Fig. 2.1). Nearly all the subsidence data obtained in the US have been derived from these two cross-sections, although some cross- sections parallel to CD but near the edges of the panel have also been included. In addition to moving horizontally toward the center of the basin, every point in the basin also subsides vertically. The magnitude of subsidence increases toward the center of the basin. Therefore surface subsidence is a three-dimensional problem and should be treated so in all cases. On all the major cross-sections, only principal subsidence and principal displacement occur. Since subsidence and displacement vary continuously in every major cross-section, three additional deformation components are de- rived, i.e., slope, curvature, and strain. On all other non-major cross-sections on the other hand the five components are accompanied by two additional components, i.e., twisting and shear strain. The seven components of the surface movement are defined as follows (Fig. 2.2): 1. Subsidence, S. On any cross-section, the vertical component of the surface movement vector is called surface subsidence. It generally points downward. But sometimes it points upward in areas ahead of the faceline or beyond the edges of the opening. In such cases it is a surface heave which is usually less than 6 in. 2. Displacement, U. On any cross-section, the horizontal component of the surface movement vector is called surface horizontal displacement. It generally points toward the center of the subsidence basin. But in steep terrain, it moves along the downdip direction 3. Slope, i. On any cross-section, the difference in surface subsidence between the two end points of a line section divided by the horizontal distance between the two points is called the surface slope of the section. 4. Curvature, K. On any cross-section, the difference in surface slope between two adjacent line sections divided by the average length of the two line sections is called the surface curvature of those two line sections. There are two types of curvature: con- vex or positive curvature and concave or negative curvature. 5. Horizontal strain, e. On any cross-section, the difference in horizontal displacement between any two points divided by the distance between the two points is called horizontal strain. If the distance between the two points is lengthening, it is tensile strain with positive sign. Conversely, if it is shortening, it is compressive strain with negative sign 6. Twisting, T. On the surface of the subsidence basin, the difference in slope between two parallel line sections divided by the distance between the two line sections is called twisting. 7. Shear strain, y. Shear strain is the changes in internal angles of a square on the surface of the subsidence basin or on any major cross-section. It is the summation of the differences in incremental (or decremental) lengths between the two opposite sides divided by the original distance between the two opposite sides. More precisely, the surface deformation indices (i.e., slope, strain, curvature, twisting and shear) are defined by derivatives of surface movement components. For simplicity, the x- and y-axes of the cartesian coordinate system are set to be parallel and perpendicular to the cross-section of interest, respectively. In such a coordinate system, slope and curvature along x direction are the first and the second derivatives of the vertical components (S) of surface movement with respect to x, respectively, or i, = ds/dx and kx = d2s/dx2. Horizontal strain along x direction is the first derivative of the component along x direction of the horizontal displacement,

Jan 1, 1992

By Rahul Singh, Sunil Kumar, Erich Dohm, Maoming Fan

The rapid increase of P2O5 use for food, biofuels, and LiFePO4 batteries etc. accelerates the depletion rate of phosphate reserves. In the phosphate industry, a significant amount of ultrafine phosphate has been discarded as slime tailing due to processing difficulties. The major problems associated with ultrafine particle flotation are low probability of bubble-particle collision and adhesion, and high probability of unwanted gangue particles entrainment. This paper investigates the enhanced ultrafine phosphate particle flotation probability by Eriez’ CavTube generated fine/ ultrafine bubbles and the improved flotation selectivity by wash water etc. Ultrafine phosphates with various gangue minerals of quartz/muscovite, calcite/dolomite, and iron/ silica were studied. Microscopic observations show that the entrained ultrafine gangue minerals can be minimized by using wash water in column flotation. A three-factor threelevel central composite experimental design was conducted for ultrafine phosphate flotation. For comparison, both benchtop mechanical cell and laboratory column flotation tests were performed at their optimal respective flotation conditions. Using Eriez CavTube column flotation technology for Industries Chimiques du Senegal (ICS) ultrafine slime tailings, a concentrate grade of 36.0% P2O5, was achieved at 89.4% P2O5 recovery. Improved flotation performance was achieved using column flotation as compared to benchtop mechanical cell flotation. The benefits of Eriez’ column flotation technology realized from this study include the high P2O5 grade and recovery.

Feb 1, 2024

By C. R. Stephan

The Mine Safety and Health Administration's (MSHA) Ventilation Division continues to evaluate proposed explosion-resistant seal designs. There are currently eleven specific designs for explosion-resistant seals that are suitable for construction in underground coal mines. Seal construction in operating mines must be equivalent to those constructed in the Experimental Mine during the explosion testing program. Accidental failures of seals have occurred due to explosion pressures below 138 Kpa (20 psi). The possibility exists that the failed seals were not properly constructed. Also, conditions in the vicinity of the seals may change. Water may accumulate against the seals, heave or sag may cause detrimental effects on the seals, and sloughage of the ribs may negate hitching. If seals are not properly installed or maintained, they could fail when subjected to explosion pressures. If seals fail for any reason, the possibility exists for explosion propagation throughout large areas of the mine. There could be catastrophic consequences to an event of this nature. This report will present a limited discussion on the construction of each of these seals and will address related issues.

Jan 1, 2001

By Will B. Jamison

The most serious safety problems encountered in U. S. underground coal mines today are related to the roof bolting operation. Also, roof bolting is usually the operation which limits coal production of the section. The purpose of my paper is to review some of the research, developments, and new ideas related to roof bolting. Many of these ideas have originated at. coal mines or with manufacturers. Most of the research on fundamental improvements has been funded by, and is a part of, the excellent and broad plans of the Bureau of Mines.

Jan 1, 1977

By Rafael C. Castro, John Overton, Gregg Sherry, David A. Sutter

This paper presents an innovative ground support solution developed to construct a tunnel cross-passage for the MUNI Metro Turnback (MMT) Project. A “soft center” jet grouting approach was designed to provide solid ground support while maintaining a soft center to allow for hand-mining of a 2.44 m (8 ft.) wide, 3.66 m (12 ft.) tall and 4.6 m (15 ft.) long cross-passage through soft Bay Mud. Prohibitive costs and schedule impacts associated with mining under compressed air (at the time being used for main tunnel construction) were the catalysts to search for alternative methods for cross-passage construction. Limited surface disruption, relatively low costs, ease of subsequent excavation, nominal schedule impacts and proven local success of jet grouting were key factors in selecting and designing this method of ground support.

Jan 1, 1997

By Yousef Ghorbani, Abolfazl Danesh, Fatemeh Kazemi, Ataallah Bahrami, Morteza Abdollahi

The abstract highlights the impact of flocculants used in the middle thickener of a copper-molybdenum plant on both process water quality and molybdenite floatability. The study investigates the effect of a starch-based flocculant (wheat starch) on the efficiency of the middle thickener and molybdenite flotation. The findings indicate that the presence of starch influences the settling behavior of particles with different shapes, and the dosage of starch affects both molybdenum recovery and the presence of copper minerals in the molybdenum concentrate.

Mar 7, 2022

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, BRADLEY BENNETT, Patrick Zhang

This study level process design represents an economically viable method for extracting thorium dioxide and other rare earth elements from monazite ore. This paper incorporates results from the 2019 capstone project from the honors Design Internship in Green Engineering in Chemical and Biomolecular Engineering. In this activity, senior students in Chemical Engineering at the University of Tennessee (UT) focused on the development and study of a process for the recovery of thorium dioxide and P2O5 from monazite. While not mandated, the process offers rare earth oxides as attractive byproducts. The project focused on recovery of byproducts rather than the creation or addition to waste streams. Additionally, (1) the process economics relied heavily on recovery of rare earth byproducts, (2) thoriumhandling portions of the process could be effectively segregated from rare earth and phosphate handling portions of the process, and (3) thorium and uranium content of waste streams should be carefully managed and eliminated where possible.

May 29, 2020

By S. Philipp

This paper describes several variants of placement and design, from a technical and economic point of view, of shafts, ore bunkers and drifts near shafts of a Russian potash mine. Advantages and disadvantages of the position of different workings are shown as well as an analysis of stratigraphic and geological layers and their use for excavating pit bottoms, haulage drifts and bunker installations. The potash mine consists of two hoisting shafts and one service shaft. The hoisting capacity of one of these skip shafts is planned to be approx. 7 Million tons of crude potash salt per year. Both shafts together will have a hoisting volume of about 14 Million tons. When the mine will increase their highest level of production, it will be one of the biggest potash mines in the world. The skips, the hoist drives and the bunker near the shaft will belong to the largest ones worldwide, too. This paper specifies the features of such a double skip shaft pit in detail and demonstrates problems, which depend on the fact that the pit bottom is in a depth of nearly 1200 m.

Feb 23, 2014

By Stephen H. Stow

The relationships between the amount of light reflected off 21 samples of Florida phosphate and the chemical, composition of the samples were examined. It was found that the reflectivity of a rock is directly related to its chemical composition and that darker phosphates (less light reflectance) have relatively high amounts of iron, organic C and sulfate while lighter-colored rocks were rich in phosphorus, fluorine and aluminum. The use of reflectivity measurements could have economic applications in the phosphate rock industry: color specifications for rock shipments could he met, beneficiations by optical sorting could be performed and semi-quantitative analyses could be made rapidly and inexpensively.

Jan 1, 1971

By James E. Lawver

During 1981 the Florida phosphate industry produced more than 43 million metric tons of phosphate rock - about one-third of the entire world production and also generated nearly an equal amount of waste clay and waste clay-sized product that requires dewatering and disposal. The material balance of solids and water for a typical Florida phosphate mining operation is shown in Figure 1. Historically, the industry has impounded clay waste (about 60% below ground and 40% above ground) in earthen dams, often as large as 800 acres and occasionally greater than 60 ft. high. The dams have served the triple purpose of: 1. Dewatering initial 3% solid waste clay for process water re-use. 2. A reservoir system to minimize water discharge from the mining area and to capture and store rainwater thus minimizing deep well pumping requirements. 3. The ultimate densification and storage of waste clay.

Jan 1, 1983

By Guodong Li, Chenlin Wang, Zibiao Yu, Bo Xu

Abandoned coal mines have many underground space resources, such as roadways, shafts, and gobs. Among them, abandoned roadways are the best gas storage space for underground compressed air energy storage (CAES). However, CAES caverns have high air pressure and strict sealing requirements. Therefore, the stability and sealing of abandoned roadways under high internal pressure must be analyzed. Afterward, the suitability of abandoned roadways used for CAES caverns should be evaluated. In this study, the numerical simulation software FLAC3D was used to calculate the stress, deformation, plastic zone volume, and pore pressure of surrounding rock in an abandoned roadway under 10 MPa internal pressure. The influence of buried depth, surrounding rock grade, and in situ stress state on roadway stability and the effect of surrounding rock permeability on roadway sealing were analyzed. Results showed that the stress, displacement, and plastic zone volume of surrounding rock were affected by high internal pressure when the buried depth was less than 300 m, but high internal pressure had little effect on them when the buried depth was more than 300 m. The suitable range of buried depth was more than 300 m. The optimal choice of surrounding rock grade was I and II, followed by grades III, IV, and V. The optimal choice of in situ stress state was σH > σh > σv, followed by σH > σv > σh and σv > σH > σh. The sensitivity of the stability evaluation parameters was ranked in descending order as follows: buried depth, surrounding rock grade, and in situ stress state. When the surrounding rock permeability was less than 1 × 10− 14m2, the 24-h air leakage rate of the roadway was less than 1%. The suitable range of surrounding rock permeability was less than 1 × 10− 14m2.

May 23, 2023

By Z. Hyder

Simulation and modeling is powerful tool to analyze real time data and can be used to analyze different scenarios using appropriate software that may reduce need of infield data collection process and can predict reasonably accurate results. In this paper the real time data of a mine is used to simulate and model the stresses on the pillars and evaluate the pillar strength and safety factor. The material properties assigned to the model are obtained by testing the representative samples taken from the selected locations of the mine. The mine under investigation has 50 ft wide pillars and 50 ft wide rooms under an average overburden of 650 feet. The effect of reduced pillar dimensions and increased roof span on overall stability of mine and extraction ratio is analyzed using LaModel [1] software. The predicted results of the reducing pillar size are analyzed to compares the current mining practices with the optimized room and pillar size to get better extraction ratio without comprising the safety.

Jan 1, 2011

By MOHAMMAD R. H. GORAKHKI, Christopher A. Bareither, MANUEL APARICIO, Joseph Scalia IV

The focus of this study was on the evaluation of hydrologic and environmental behavior observed in GeoWaste and waste rock test piles. GeoWaste is a mixture of fast-filtered tailings and waste rock prepared as a tailings-dominated mixture. The two test piles included potentially acid-generating (PAG) waste rock and were operated for 26 months to evaluate whether GeoWaste can suppresses sulfide oxidation and production of metal-rich acid mine drainage relative to PAG waste rock. The test piles were constructed in the shape of truncated 5-m-tall pyramids with 25-m base sides and flat 5-m × 5-m top surfaces. Water content, temperature, electrical conductivity, and oxygen concentration were monitored in four layers and at five locations within each layer in both test piles. In addition, 5-m × 5-m lysimeters were installed at the base of each pile to collect leachate. Approximately 2660 mm of water was added to the surfaces of the test piles via precipitation and irrigation (irrigation ≈ 1050 mm applied at an approximately constant rate for 70 days). The measured saturation, oxygen concentration, electrical conductivity, and temperature in the GeoWaste and waste rock piles suggest more sulfide oxidation occurred in the waste rock pile compared to the GeoWaste pile. Observations from the pile experiments suggest that co-managing mine waste in the form of GeoWaste reduced acid generation compared to waste rock alone due to the lower permeability and unsaturated state of the GeoWaste pile that reduced downward migration of moisture and inhibited drainage.

Mar 31, 2021

By Peter Shuttleworth, Chris Fesq, Eddie Woods

Precast concrete segmental linings for tunnels have traditionally been designed with conventional steel bar reinforcement. In many cases, this has been satisfactory in service, but in others, major problems have occurred with the durability of the linings. Commonly this has resulted from corrosion of the reinforcement, mainly from chloridesin ground water, causing spalling of the concrete and leading to very expensive and disruptive repair programs. This paper discusses the relative merits of designing tunnel linings with steel fiber reinforcement to provide long-term durability, improved impact resistance and toughness for greater load capacity across joints, enhanced robustness during transportation and erection, plus improved fire resistance with the addition of polypropylene fibers. Guidance is also given in the selection of the correct fiber type, mix design and testing methods to establish the optimum dosage required and production techniques to ensure even distribution and compaction.

Jan 1, 2005

By N. Careddu

In recent years, slabs with a rough surface have captured a large share of the ornamental stone market. However, the main technologies used for this type of treatment are based on mechanical shock (bush-hammering) or thermal treatment (flaming or flame-finishing). These traditional technologies are widely used, but have many limitations that decrease their usefulness. The purpose of this study was to develop a technology that enhances the natural colors of the rock and produces a rough surface without compromising its mechanical characteristics, in contrast to traditional technologies. This report shows the technical, economic and aesthetic results obtained with a new water-jet treatment and compares it with competing technologies.

Jul 1, 2010

In 2011, the value of mineral production increased in the United States for the second consecutive year (Table 1). Production increased modestly for most mineral commodities mined in the United States, and price increases, especially for precious metals, resulted in increases in the value of production. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Minerals? contribution to the GDP increased for the second consecutive year. Trends in other sectors of the domestic economy were similar to those in mineral production and consumption rates. U.S. apparent mineral consumption (industrial) of 11 mineral commodities decreased substantially from 2005 to 2010 (aluminum, cadmium, cement, copper, iron, lead, salt, soda ash, steel, tin and zinc). Data for 2011 were not calculated, but the data show a sustained decrease (especially for the metals) preceding the recession through 2010, so consumption seems to be behaving differently than production and GDP. After continued decline following the 2008?2009 recession, the construction industry began to show signs of improvement during 2011, with increased production and consumption of cement, construction sand and gravel, and gypsum ? mineral commodities that are used almost exclusively in construction. Crushed stone production, however, continued to decline.

Jan 1, 2012