Search Documents

By Fengyu Ren, Kunpeng Yu, Gideon Chitomb, Qiangqiang Gao, Liqiang Ma, Jiangtao Zhai, Ichhuy Ngo

The penetration of rock fragments of overlying strata causes advanced ore dilution during drawing. The results of numerical and physical experiments showed that the proposed numerical simulation was applicable and the microscopic parameters of the model were reliable. The penetration under the variables of particle diameter ratio, density ratio, overlying strata thickness, and particle morphology was clarified. The penetration was quantitatively characterized by the discharge amount and the dilution rate. The experimental results showed that the diameter ratio and density ratio had a significant influence on the penetration. On the irregular shape of particles, the penetration is weakened. The overlying strata thickness had little effect on the penetration. This study could provide a theoretical basis for the full section uniform drawing, avoiding advanced ore dilution and further optimization of recovery rate.

Nov 13, 2023

By Francisco J. Escandon V.

Numerous lead-zinc-barite-fluorite ore deposits, with simple mineralogy and roughly concordant with bedding, are found widely distributed all over the world, having been denominated and well described as "stratiform deposits" or "strata-bound ore bodies", not having any genetic relationship. During several years, its origin has been discussed, without getting to general agreement regarding the main mining districts of this type. Through studies made of large stratiform deposits in the United States, Europe and Russia, it has been found that there are, within this classification, syngenctic diagenetic and epigenetic ore bodies. During the Symposium about the genesis of the stratiform lead-zinc-fluorite-barite deposits, carried out in New York in 1966, Frank G. Snyder (1), presented an excellent analysis of the theories of the origin of these deposits and of the evaluation of the criteria regarding classification. As per his definitions (Table 1), "a deposit is syngenetic if formed by processes similar to and simultaneously with the enclosing rock, epigenetic if introduced into a pre-existing rock and a diagenetic origin implies deposition of metals with the host sediments but with recrystallization, rearrengement and limited migration".

Jan 1, 1974

By Xiaodong Yu, Jinxia Zhang, Fusheng Niu, Hongmei Zhang

The three-dimensional (3D) fractal dimension is an important parameter to analyze the 3D structure and flocculation effect of the hematite flocs. In this work, the 3D fractal dimension of hematite flocs was predicted by establishing the particle swarm optimization (PSO) algorithm optimized with the back propagation (BP) neural network (PSO-BP). The proposed model considers four factors, namely, the flocculant quantity, flocculation time, stirring speed, and temperature, as the input parameters. We normalize the input data during the preprocessing stage. The BP neural network was optimized by using the PSO algorithm for realizing the 3D fractal dimension. The prediction accuracy and effectiveness of the model were evaluated. The experimental results showed that the predictions performed by the proposed PSO-BP neural network were better than that of BP neural network. In addition, the root mean square error (RMSE), mean squared relative error (MSRE), mean absolute error (MAE), and mean absolute relative error (MARE) of the proposed model are lower, compared with the errors of the BP network. Similarly, the measurement coefficient R2 of the proposed model is higher, compared with the BP network. The maximum absolute error of the model is 0.0772, the maximum relative error is 0.02405, and the regression coefficient r is 0.98592. These results showed that the proposed model has a good performance and high prediction accuracy. When verifying the practicability and the effectiveness of the proposed PSO-BP model, the prediction results of 10 groups of hematite flocculation experimental data under different conditions showed that the prediction value of the proposed PSO-BP model was closer to the ground truth as compared to the BP model. Therefore, the proposed model is suitable for predicting the 3D fractal dimension of hematite flocculation.

Oct 3, 2022

By Ali Hafiz, Rich McCafferty, Chris Blanchard, Kaz Tabrizi, Kevin Ruston, Joseph Rigney, Mike Keville, James Dorta

Many existing tunnels have deteriorated as they age, requiring a massive amount of investment for their rehabilitation. The tunnel of interest in this paper is being rehabilitated by adding precast concrete arch panels under the existing concrete ceiling, and measuring the gap between them was the objective of this research. For this purpose, a mobile 3D laser/thermal scanner was used for scanning the tunnel, especially for the purpose of measuring its profile. To calculate the gap, the distance between the tunnel profile and the theoretical profile of the concrete arches was measured. Additionally, an in-house program was developed using MATLAB to automate the data processing to determine the above-referenced gaps. Results were provided in the form of heat maps showing the measured gap.

Jun 23, 2024

PolyMet Mining is developing the NorthMet property near Duluth, MN. Laboratory investigations have led to the development of the Platsol process to dissolve in one step the base metals (copper and nickel) as well as the gold and platinum group metals (PGM). To complete the prefeasibility study, a fully integrated, 10-day pilot plant trial was undertaken. The trial consisted of high-temperature (>220ºC or >428ºF) pressure oxidation in the presence of 5 to 10 g/L chloride (the Platsol process). This was followed by solid/liquid separation, gold plus PGM recovery from solution, conventional copper solvent extractions/electrowinning (SX/EW) and recycling of the copper raffinate to the autoclave. The concentrate tested during the trial period was a NorthMet bulk flotation concentrate. It assayed 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t (0.041 oz/st) Au, 2.2 g/t (0.064 oz/st) Pt and 9.9 g/t (0.289 oz/st) Pd Laboratory results were confirmed and, with minor adjustments of the laboratory Platsol conditions, the following leach extractions were obtained during the pilot plant trial: 99.6% Cu, 98.9% Ni, 96% Co, 94.6% Pd, 96 % Pt and 89.4 % Au.

Jan 1, 2003

By Yaxiong Wang, Yong Li, Yuedong Wu, Haigang Dong, Jiachun Zhao

A roasting-leaching process has been developed for concentrating platinum group metals (PGM) from a PGM-containing ferroalloy. The optimized roasting conditions used a NaOH-to-ferroalloy mass ratio of 1.2 at 600 °C for 2 h. The roasted product mainly comprised Na4SiO4, NaFeO2 and Fe2O3. The iron oxide and sodium silicate associated with the roasted product were leached in water and dilute sulfuric acid solution, while the PGM was concentrated in the acid-leached residue. A PGM concentration of 23.4% was obtained with assaying, and the concentration factor of PGM from the ferroalloy to PGM concentration was greater than 9.

Jun 14, 2021

By B. W. Cavender

Innovative mining and metallurgical operating techniques or processes can be identified and developed by systematically analyzing change as it occurs within the mine, plant, technology, or industry. Sources of change to be monitored for innovative opportunities include unexpected successes or failures, incongruities between perceived and actual events, process needs, changes in perceptions, and the development of new knowledge. Innovation can be effectively organized, practiced, and managed. The perception of change as an opportunity rather than a threat is mandatory, as is the systematic measurement of innovative performance. Innovation is enhanced by specifically-designed policies regarding organizational structure and staffing, daily management practices, and compensation and incentives.

Jan 1, 1994

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents the preliminary test results obtained using a 0.38-kg/s (3,000-lb/hr) beta prototype MagMill. In processing Upper Freeport coal, the beta prototype recovered 82 % of the weight of the feed and 91 % of the heat content while reducing the potential emissions of sulfur by 61%. Pyritic sulfur in the MagMill product was reduced by 78% compared with that in the feed. For all runs, the mill product particle size was controlled to between 70% and 80% -741m (200 mesh). Recoveries of mercury, arsenic and selenium ranged from 35% to 45% of the amounts found in the feed. Power draw was reduced by 26%, and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2002

By E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Leadership is a critical component to an organization’s safety culture and influences the ways that health and safety is enacted on site. Therefore, it is not surprising that improving leadership will also improve safety. Worker perceptions of management practices are shaped through unique leader-employee interactions over time. However, few details are known about the communicative support (i.e., emotional, informational, and tangible) offered by supervisors and its impact on miners’ perceptions and performance. Using pre and post-interview data with 20 supervisors and 48 workers during six-week interventions, researchers identified positive and negative instances of supervisor support and its implications on worker performance. This paper highlights the common support tactics offered by supervisors and desired by workers to help practitioners identify ways to improve their safety culture and subsequently, the proactivity and compliance of their workforce. INTRODUCTION Supervisory leadership is a critical component to the effective implementation of an organization’s health and safety management system (HSMS). Specifically, supervisors serve as representatives of an organization and their actions are indicative of the organization’s safety culture (Eisenberger et al. 1986). Senior management has been shown to serve as a frame of reference for guiding safe behaviors in the workplace (Mearns et al. 1998) and, more recently, research has related supervisory enforcement to workers’ safety compliance (Petitta et al., 2017). Therefore, it is not surprising that by improving leadership, perceptions of management and subsequent safety outcomes are likely to improve as well (Zohar, 2002). Perceptions of management are shaped through unique leader-employee interactions over a period of time (Hofmann and Morgeson, 2004, 1999). How these unique interactions impact worker performance, however, remains unexamined. As a result, understanding how supervisor-employee relationships operate in high-risk environments is unclear (Mirza and Isha, 2017; Denis et al., 2010). A starting point to better recognize the idiosyncrasies of these relationships is by way of examining the communicative support offered by front-line management and received by industry workers. To this end, this paper uses pre- and post-interview data to study the communicative aspects of supervisor-employee interactions at mine sites. The analysis uses a social support framework to identify positive and negative instances of supportive communication. From interview data with 20 managers and 48 mineworkers, data emerged that shows how supervisors’ unique types of support contribute to workers’ perceptions, motivation, and follow-through of safe work behavior.

Jan 1, 2019

By E. G. Cauda

Diesel engines are a major source of underground miners? exposure to nitrogen dioxide. In an effort to reduce the exposure of underground miners to regulated and unregulated diesel emissions, primarily particulate matter, mining companies in the U.S. are retrofitting existing and introducing new engines with various exhaust aftertreatment technologies. Different aftertreatment devices, or changing the operating temperature of a selected device, can have unexpected effects on the concentration of nitrogen dioxide emitted by a diesel-powered piece of equipment. This paper provides an overview of the effects different exhaust aftertreatment technologies available to the mining industry have on no2 emissions.

Jan 1, 2010

By Robin J. Hickson

El Abra is one of the world’s premier copper de-posits. The project is located in northern Chile, 140 km (87 miles) inland from the Pacific coast. It has the same geologic age and structural setting as the world-class Chuquicamata copper mine located 42 km (26 miles) to the south. The current development plan for El Abra extracts798 Mt (879 million st) of high-quality oxide ore. This will require building a solvent extraction/electrowinning(SX/EW) facility that can produce 225 kt/a (248,000stpy) of cathode copper. This will make El Abra the largest SX/EW copper operation in the world, and the world’s seventh-largest copper producer.

Jan 1, 1996

By Robert L. Sundeen, Richard V. Wenberg

Overshot loaders are loading machines which fill a front-mounted bucket by crowding and bucket lifting, passing the loaded bucket over the machine and throw¬ing the load into a haulage unit to the rear. The load is retained in the bucket as the load mass is accelerated in its path over the machine. At the point of discharge, the bucket is stopped suddenly and the load leaves the bucket, following the throw trajectory past the rear of the loader. Fig. 1 shows a typical overshot loader of this type. Overshot loaders were developed for loading in nar¬row drift headings and drawpoints, where it is impossible to place or pass a haulage unit alongside the loader. Haulage access is to the rear of all overshot loaders. The first overshot loader was developed in the early 1930s. The early machines were rail-mounted, air¬powered, and had small loading capacities. To this day, the same basic design configuration exists, and all suc¬cessful overshot loaders still use compressed air. Bucket sizes range from 0.14 to 0.59 m3 (5 to 21 cu ft). The most commonly used machines are rail-mounted, al¬though crawler versions are popular for special applica¬tions, particularly shaft sinking. Rubber-tired machines have found some application where a greater travel distance is required between the loading and discharge points. CONDITIONS INFLUENCING APPLICATION Roadway Type Rail-mounted loaders are used where soft bottom requires rail support or where the long haul is ac¬complished with rail. This situation usually occurs in civil tunnels or in mine drifts that will continue to utilize rail-bound main haulage after development work is completed. Crawler and rubber-tire mounted loaders are used where the roadway surface is rough and lateral travel beyond the range of rail-bound machines is required. Work Area Dimensions The largest rail-bound loaders can clean roadways as wide as 4 m (13 ft) from a single track. Wider headings require multiple trackage. Headroom require¬ments are dependent upon the path described by the bucket as it passes over the machine. The largest over¬shot loader requires approximately 3.4 m (11 ft) of headroom. It follows that the largest heading that can be driven by overshot loaders from a single set of rails is approximately 4 m (13 ft) wide and a minimum of 3.5 m (11.5 ft) high above the rail. The smallest rail-bound loaders can work efficiently in headings as small as 1.8 m (6 ft) wide by 1.8 m (6 ft) high above the rail.

Jan 1, 1982

By C. V. Deutsch, T. Acorn

Understanding and managing risk is of increasing concern for the mining industry. Although methods exist to model geologic uncertainty based on stochastic modeling techniques and multiple realizations, there are few approaches to manage this geologic uncertainty in pit optimization. Block values can be penalized if the block uncertainty is high, but the goal here is to consider the reserve risk within the pit. This paper presents an approach for pit optimization that considers all realizations simultaneously with a heuristic pit optimizer. The heuristic algorithm maximizes value and also penalizes reserve risk. The inclusion of multiple realizations provides access to the risk or uncertainty in the total pit value. Considering this information permits an active risk management approach that can manage the uncertainty in the reserves within the entire pit.

Jan 1, 2018

By D. A. Dahlstrom

With today's high energy costs per million BTU's, far greater emphasis is placed on increasing thermodynamic efficiency in the use of energy. America has long since discarded its previous golden age of "low cost energy" in the past ten years. Energy costs are now a very significant percentage of operating expense in industrial operations. Public utilities have felt the same influences of increasing costs in energy for the generation of electricity. Not only has the input energy expense increased seriously, but as pointed out by Blackmore in a paper, fuel costs were 53.4% of the total operating costs for American Electric Power Company.

Jan 1, 1983

By R. J. Pindred

Discussion by R.J. Pindred In his paper, Davis presents an overview of risk. He also introduces the Capital Asset Processing Model (CAPM) as a foundation for selecting the appropriate discount rate for a mining project. While applying portfolio theory is more defensible than the ad hoc adjustment of discount rates, the CAPM is not a panacea. CAPM shortcomings [The CAPM, as Davis stated, is expressed in the equation: ri=rf+pi4) where ri is the project discount rate rf is the risk free interest rate (3i is the project beta, and 0 is the market risk premium (rm - rf)] Application of the CAPM is more difficult than Davis indicates. Valuation is prospective, while the CAPM parameters are historical. Beta is determined from a regression analysis of historical data, while the beta needed for valuation is the expected beta. Betas are known to be unstable and the regressions that generate them often have low explanatory power. The difficulty of estimating a "project" beta must also be considered. Thus, the beta that is used in the CAPM will be based on the analyst's judgment. Like Cavender's discount rate, this judgment can lead to different project NPVs. Subjectivity in valuation cannot be avoided by a mechanical application of the CAPM. The risk-free rate, which Davis identifies as a short-term real rate of 4%, is also subject to scrutiny. A mining project is not a short-term investment and no single risk-free rate is appropriate for all of the cash flows. The hypothetical mine discussed in Cavender's paper is a six-year project. One might argue for the application of a risk-free rate from the Treasury yield curve at the duration of the project (in a bond-duration sense). This, too, is inappropriate. The risk-free rate should be matched to the timing of the cash flow. These rates can be determined by calculating the implied forward rates from the yield curve using a procedure known as "bootstrapping." It is likely that each of the project's cash flows would be discounted at a different rate. Commodity prices Davis criticizes the "ad hoc adjustment to the discount rate." Yet, in his discussion of the value of stochastic simulation, he suggests that the gold price be modeled as a "random walk, with or without a trend." This is essentially an arbitrary modeling of price risk. Consider that a liquid market in gold futures exists. The futures' price curve, which is closely related to the market's estimate of future spot gold prices, should be used to provide inputs to the model. This is especially true of a relatively short six-year project. Alternatively, as Davis correctly points out, a risk-averse investor can sell the commodity short to hedge price risk. Is it any more correct, in the portfolio sense, to account for price risk at all ?? References Cavender, B., 1992, "Determination of the optimum lifetime of a mining project using discounted cash flow and option pricing techniques," Mining Engineering, Vol. 44, No. 10, pp.1262-1268 Fabozzi, F.J., 1993, Bond Markets, Analysis and Strategies, Second Edition, Prentice Hall, Inc. Higgins, R.C., 1992, Analysis for Financial Management, Third Edition, Richard D. Irwin, Inc. Solnik, B., 1991, International Investments, Second Edition, Addison Wesley Reply by G.A. Davis Pindred discusses two issues related to my paper, the shortcomings of the Capital Asset Pricing Model (CAPM) and which commodity price values to use in the valuation exercise. Even though these topics are not directly related to the use or misuse of Monte Carlo simulation, they are important points to take into consideration in valuation exercises. Since I do not appear to have addressed these issues satisfactorily in my original paper, I will comment on each here. Pindred agrees with me that applying portfolio theory, and specifically the CAPM, to the selection of project discount rates is more defensible than ad hoc methods. But he then points out that the application of the CAPM to project valuation is more difficult that I indicate. It is true that the CAPM is a difficult tool for project valuation in general,. But the application of the CAPM to mining projects is one of the easiest I can think of. The biggest problem with using the CAPM for project valuation is coming up with an expected project beta. I suggest a project beta for gold projects of 0.45. The "true" value might be 0.35, 0.55 or whatever. Pindred correctly notes that the selection of the appropriate project beta is based

Jan 1, 1996

By Harry Perry

U. S. consumption of sulfur and sulfur products is expected to increase at a rate of 8 percent per year between now and 1980, largely as a result of their use in fertilizer markets. World consumption is also increasing rapidly, but at a-lower rate, about 6-percent per year. In 1965, sulfur recovered in the United States from purification of natural gas; nearly doubled from the 1956-1960 average; production from pyrites declined; and production of elemental sulfur increased 15 percent. Concern about air pollution resulting from sulfur oxides produced from the combustion of fossil fuel has lead to intensive research on methods of removal before combustion, during combustion (in-process methods), and from the resulting flue gases. If all the sulfur in fossill fuels were recovered, more sulfur products would be produced than were consumed in the United States in 1965. Removal of sulfur from coal before combustion could result in a product sufficiently-high in sulfur to be a suitable raw material for sulfuric acid manufacture. In-process methods produce solid sulfates, some of which may have commercial value. Flue gas removal' methods for sulfur oxidest generally result in the production of a byproduct either of sulfuric acid or sulfur. The projected sale of these materials significantly lowers the anticipated cost of sulfur dioxides pollution abatement. Alternate methods for sulfur dioxide reduction are discussed. The various proposed processes are described and costs are given for the various methods for which estimates have been made.

Jan 1, 1967

The ability to increase and maintain dragline productivity is a key mine driver for the Coal Creek Mine. The Coal Creek Mine is owned by Arch Coal Inc subsidiary Thunder Basin Coal Company; located near Gillette, WY. Coal Creek Mine overburden stripping is primarily accomplished by a BE-1570W walking dragline in combination with cast blasting and dozer assist for bench preparation. The two main variables impacting dragline performance are maintenance reliability and operator skill levels. The mine?s most recent process improvement efforts have focused on its most valuable asset - the operator. Various techniques have been used to reduce variability in the dragline operator?s digging performance. Utilization and communication of operator performance data, statistics, and video reviews have been of great value towards achieving this goal. Operators are given a chance to critique operational tendencies from a third-person point of view, and are also presented statistical feedback to support observations. From these sessions, operators gain knowledge as to what portions of the dig cycle can be improved in order to reduce cycle time and increase productivity. BACKGROUND The BE-1570W walking dragline was commissioned at Coal Creek in November 2006 after relocating from Arch of Wyoming located in southeast Wyoming. The first two years of operation the machine was performing simple side cast stripping due to the low ratio. Coal Creek Mine is a multiple seam operation with overburden thickness ranging from 24 to 140 feet. Early in 2009 the ratio increased to the point where transitioning to cast blast/extended bench stripping was necessary. The current mining conditions consist of a mixture of both stripping styles where the ratio allows. The dragline crews running the machine consist of a mixture of experience levels ranging from 30+ years to only a few years. It has been in this digging environment and slightly inexperienced personnel that the focus has been set for improvement in dragline performance.

Jan 1, 2011

By H. Sevim

The utilization of high sulfur Illinois coal by utility plants has been decreasing since the enactment of 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal saleable by offering the choice of taking the combustion by-products from the utility plants and placing them in the abandoned sections of their mines. To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of by-product disposed can be minimized. In this paper, a few such systems are presented. The favorable operating range of each system is determined in terms of distance and tonnage. A case study is given whereby cost analysis is conducted for an underground coal mine receiving by-products from two Illinois utility plants.

Jan 1, 1997

By Donald Towse

Geothermal heat might become an important fuel for several reasons: (1) To substitute for other scarce and critical fuels. (2) Because it may be less costly to the user than alternate fuels. (3) Because its production may be more profitable than production of other fuels. (4) Or for a number of other more or less non-economic reasons such as convenience or because of less environmental impact. In competition with conventional and other non-conventional fuels, geothermal heat must score well on one or more of those points. This study first considers projections of energy needs in several United States economic sectors and the technical possibility of geothermal heat substituting for other fuels in those sectors. Then, reported and projected costs of energy from geothermal heat are compared with costs of other fuels to show the relative costs of fuels in several economic sectors. Relative costs are reported from a sample of real and hypothetical geothermal projects. The actual cost of energy will vary with each application and the particular circumstances of each geographic location.

Jan 1, 1975

By B. J. Scheiner

The Bureau of Mines, Department of Interior, has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. Lt was found that at a given polymer concentration, there was an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987