Search Documents

By Jr. Pickering

Kaolin is mined from extensive sedimentary formations in the eastern Amazon River Basin of Brazil. Production began about 25 years ago from 30 meter thick beds of ultra-fine particle clay of superior viscosity along the Jari River north of the Amazon. Operated by CADAM S.A., capacity now exceeds 750,000 tonnes per year ot high glossing paper coating kaolin product. South of the Amazon on the Capim River are two new operations: Para Pigmentos S.A. and Rio Capim Caulim S.A. The purity , and large coarse plate-shaped particles of these Capim kaolins support production of superior brightness and whiteness paper coating and filling grades. Annual capacities are reported to be 150,000 to 300,000 tonnes each, with expansions planned. Most of Amazon area kaolin production is shipped to western European, Asian, and North American markets.

Jan 1, 1999

By J. H. McNamara

A process has been developed for the successful hydrometallurgical extraction of copper from sulfide ores. The extracted copper in the form of a salt is converted by reduction to copper metal. Purification of the metal is described which includes a description of the casting of ETP quality copper wire bars.

Jan 1, 1978

By P. Bissert, M. Klein, L. Yan, D. Yantek

"Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hrs. One of the main concerns with the use of mobile RAs is the heat and humidity buildup inside an RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in a fully occupied RA must not exceed 95°F. To investigate this issue, the National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4°C (17°F) and the relative humidity (RH) approached 94 %RH. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the average air temperature inside the RA at the end of 96 hours to within 0.6°C (1.0°F) of the average measured air temperature. INTRODUCTION If an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke, or even death. In its 2007 report to Congress, the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) recommended that RAs should be designed to ensure that the internal apparent temperature (a temperature-humidity metric) in an occupied RA does not exceed 35°C (95°F). However, a standard method to determine compliance with this metric does not exist. The heat transfer process within and surrounding an RA is very complex, and is not easily defined analytically or experimentally. To investigate the related issues, OMSHR conducted heat and humidity testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. During the testing, numerous parameters were measured: heat input to the chamber, the air temperature and relative humidity inside the RA, the air temperature in the mine, the mine strata temperatures versus depth, and the airflow inside and outside the chamber. The focus of this paper is on the temperature rise within an RA. TAITherm heat transfer analysis software was used to develop a thermal simulation model of the RA as it was tested in the mine, using the test results as the benchmark. Both sensible and latent heat were used in the test and the model."

Jan 1, 2016

By Simón Díaz-Quezada, HUMBERTO ESTAY

The heap leaching process has been widely used for recovering different metals since its first application at the end of the 1960s. In Chile, copper production via heap leaching has accounted for between 30 and 40% of annual copper production over the past 10 years. This level of production has been achieved through and supported by the use of a mathematical relation, known as the leaching ratio (LR) or irrigation ratio (IR), which relates operational parameters with metal extraction in a heap leaching operation. This ratio has been used to develop leaching column tests, to scale up results from the laboratory to industrial operations, to design new heap leaching plants, and in metallurgical control and production estimation. In spite of the widespread industrial use of this relation, few scientific studies mention it. This is due to its simplicity and basic theoretical foundations. This disparity between industrial practice and scientific research could lead to operational decisions which lack substantial theoretical support, and to scientific studies which have limited industrial impact. Against this background, several questions arise about the use of the LR: What are the constraints on the use of the LR? Are there practical advantages with respect to reported kinetic models? What is the main reason that industry prefers the use of the LR over kinetic models, which enjoy greater theoretical support? In order to guide its future use, this paper describes the leaching ratio and its current uses and limitations, through a literature review and case studies.

May 2, 2020

By Chester A. Rowland

La conminución de Ios minerales es, generalmente, una etapa de preparación de la alimentación para las subsiguientes etapas del proceso. La molienda, fase de conminución de productos finos, requiere una gran inversión de capital y frecuentemente es el área de máxima utilización de potencia y de materiales resistentes al desgaste. La molienda se produce normalmente en tambores rotativos que utilizan un medio de molienda que se pierde en la misma, al elevarse con la rotación del tambor, se rompe el mineral por combinación de los efectos de impacto, atrición y abrasión, hasta producir el producto especificado. El medio de molienda pueda ser: - El propio mineral (molienda autógena - primaria y secundaria). - Medio no metálico, natural o fabricado (pebbles) - Medio metálico (barras o bolas de acero) Este capítulo tratará de molinos de barras y bolas que utilicen medio metálico de molienda.

Jan 1, 1982

By J. A. Halt, E. Larsen

"The Sydvaranger magnetite mine closed in 1996 due to low iron ore prices and was reopened in 2009. The flowsheet has remained more or less as in the old plant, based upon two grinding steps followed by magnetic separation. The magnetite is free of harmful elements and should be attractive on the high quality market. This requires a concentrate containing less than 2% SiO2, which previously was achieved by amine flotation. Amine was preferred because it could be used with sea water. The use of amine is now restricted by the Norwegian Climate and Pollution Agency. Therefore, testwork to replace cationic with anionic flotation was done. Activation of quartz with Ca or Mg ions prior to anionic flotation was shown by research from 1960 to 1980 to be effective under laboratory conditions. The old research results have been followed up in order to make a commercial process for Sydvaranger. Calcium activation works excellently with all Sydvaranger ores, including the ones containing amphibole minerals, but Ca activation requires the high and not environmentally friendly pH of 12.4. Magnesium activation at pH 10.5 is a little more challenging, because the maximum concentration of MgOH+ is about 100 times lower than that of CaOH+. Fortunately, the major impurity in the main Bjornevatn orebody is quartz, which responds well to Mg activation. The process does not appear to depend much upon water quality, as the silicates may already be activated during grinding and magnetic separation in recycled water. The new process is environmentally friendly, as only well-known household reagents are used; oleic acid or tall oil, dextrin, sodium hydroxide and magnesium chloride at pH 10.5.IntroductionThe processing plant of Sydvaranger Gruve AS (SVG) is located in the port town of Kirkenes in the northernmost part of Norway, 10 km by rail from the high-grade deposit of Bjornevatn. This plant has been able to beneficiate magnetite ore to up to 99.5% purity, as described by Sandvik and Malvik (2001). Using the magnetic properties of the ore and making the most out of its enviable liberation characteristics, the original plant consisted of ball mills and 600-mm magnetic separators. The plant was shut down due to market conditions in 1996 but reopened in 2009."

Jan 1, 2015

By A. A. Schweizer

This paper documents the growth and projects the future of Green Diamond Sand Products. Since1954, Green Diamond, located in Riddle, Oregon, has been producing sand from granulated nickel slag for use in various markets. Through the years, the company has seen several changes from its ownership to its product lines. In 1991, Green Diamond was producing abrasive sand at a rate of about 30,000 tons per year. It was at this time that Green Diamond became part of Glenbrook Nickel Company. Over the next eight years, Green Diamond would quadruple its production to over 140,000 tons while moving into three new markets, as well. Green Diamond is now producing sand for use in the abrasive, foundry, construction, and roofing industries. In 1998, Green Diamond again found itself under new, private ownership. With plans on developing agricultural sand and spent abrasives recycling, the future of Green Diamond appears to be one of further expansion coupled with diversification of its product lines.

Jan 1, 2000

By Arash Nikvar‑Hassani, Timothy Batchler, Lianyang Zhang

Recently, a new hybrid geopolymer/biopolymer (GP/BP) cementitious material was developed for improving the performance of pumpable roof supports in underground mines. This study demonstrates the application of the hybrid GP/BP cementitious material and validates its effectiveness in full-scale. In this regard, eight (8) full-size (0.61 m diameter and 1.52 m height) cribs were produced in collaboration with Minova International Ltd and tested at the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) Laboratory. These full-size cribs were produced with different material configurations to evaluate the effect of water to solid (W/S) ratio, Portland cement (PC) content, and BP dosage. The results demonstrated and validated the effectiveness of the hybrid GP/BP cementitious material in increasing the peak and residual bearing capacities of pumpable cribs and eliminating the issue of deterioration when exposed to air compared with the conventional Portland cement/fly ash (PC/FA) cementitious material currently used in practice. On average, the peak uniaxial compressive strength (UCS) and the highest residual UCS after peak of the full-size cribs produced from the hybrid GP/BP cementitious material are 1.90 and 1.33 times of those of the PC/FA-based full-size cribs by one company and 2.32 and 1.66 times of those of the PC/FA based full-size cribs by the other company, respectively.

Feb 6, 2024

By J. L. Workman

The stability of spoil and highwall slopes are important to successful strip mining. This paper discusses soil parameters of importance in stability analysis. The common mechanisms of spoil failure are discussed. Modes of highwall failure are also outlined. The importance of water to stability is presented. Dragline mining methods most suited to creating spoil and highwall profiles that address stability needs are provided. It is concluded that groundwater and surface runoff must be well controlled, and that it will often be necessary to modify spoil and highwall configurations to achieve a stable overall slope angle.

Jan 1, 1996

By F. Rudloff, C. Karageorgos, J. Moyo, I. Boadi, M. Struble, B. Lumsden

Over it’s more than 100-year history, the Kennecott operation has often been at the forefront of innovation; driven by the demands of the lower grade ore-body and the higher costs of operating in the US where wages are generally higher and regulation more restrictive. One way of reducing operating costs in c/lb is to increase the lbs produced at minimal cost. Despite the relatively coarse grind at Kennecott - about 30% >150μm, approximately 20% of the Cu lost to tail is liberated chalcopyrite in the <20μm fraction, and about 30%-40% in the <37μm fraction. In 2020 Kennecott undertook a detailed plant scale test of the magnetic aggregation technology to increase copper recovery by reducing fine copper losses. A paired statistical plant test of magnetic conditioning on one rougher line showed a 1.12% increase in Cu recovery to 97% statistical confidence. The next challenge, unforeseen at the start of the project, was the fabrication and transportation to site of the equipment for the three remaining rougher rows, during the severe supply-chain constraints of the Covid pandemic in 2021. This resulted in delays and unforeseen costs as world-wide transportation became chaotic, particularly transportation via west coast USA. Nevertheless, the project was completed and commissioned, with only minor delays and cost increases, due to a flexible approach to overcoming the hurdles encountered.

Feb 1, 2023

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals dore&apos; from ores, principally silver bearing with associated gold co-products. In late 1995 a new orebody was commissioned, the Stone Cabin orebody, and the site began a phased shift from silver dominance to gold dominance in terms of precious metals revenue. The Knelson Concentrator was selected to remove gold from a portion of the cyclone underflow stream in the grinding circuit. This paper describes the development of the flow sheet, specific mineralogical impacts on Knelson product and downstream materials, and impacts on mine/mill grade reconciliation.

Jan 1, 1997

By Katerina Adam

During wet grinding the electrochemical interactions between grinding media and pyrrhotite not only accelerate the media wear but also adversely affect the flotation response of the sulfide mineral. A possibility of remedying the adverse effect on its floatability by applying electric potentials to grinding media was examined. Flotation tests, Auger electron spectroscopy and x-ray photoelectron spectroscopy were used to study the surface properties of pyrrhotite. Although anodic polarization of the steels increased the metal loss by corrosion, the flotation recovery of pyrrhotite was increased. In the case of cathodic polarization, the flotation recovery improved in a narrow range of overpotentials. At higher cathodic overpotentials, however, the floatability of the mineral was progressively lowered although the corrosive wear of grinding media might be reduced.

Jan 1, 1984

By W. Miles

Introduction From a historical perspective, bentonite is the common rock term for various uses and applications. Its name originates from water-based muds near Fort Benton used for lubrication of wagon wheels during the 19th century migration to western territories (which are presently part of the United States) when the pioneers ran out of axle grease. From a clay mineralogy perspective, bentonite is composed primarily of montmorillonite, an expandable magnesium aluminum silicate clay mineral. When magnesium occupies an octahedral structural site that usually contains an aluminum atom, a negative charge is created. In order to neutralize negative charges, cations are drawn to the interlayer surfaces between clay mineral sheet structures. Modern applications for bentonite depend on the sodium or calcium cation populations and other characteristics of the clay mineral. When sodium is the dominant cation, the material is also called sodium bentonite, also known as swelling bentonite, western bentonite or Wyoming bentonite. When calcium or magnesium is the dominant cation, the material is called calcium bentonite, also known as nonswelling bentonite or southern bentonite. Swelling bentonite is recognized for its rapid hydration of interlayer sodium and subsequent dramatic expansion up to more than 20 times its original volume. Low shear can then disperse the hydrated sodium bentonite to form suspensions that increase viscosity and suspend solids. However, when shear is subsequently eliminated a sodium bentonite slurry gels. Characteristically, nonswelling calcium bentonite has relatively poor hydration properties and thus low expansion of the clay mineral. When subjected to low shear, calcium bentonite exhibits very little viscosity and poor suspension. Additionally, when shear is subsequently eliminated no more than minimal gelling takes place. The domestic and export markets related to both swelling and nonswelling bentonite are discussed below.

Jan 1, 2007

By B. Goertz

Since the turn of the century the mining industry in the United States has had a number of serious mine explosions, fires and ground fall disasters that have led to a major re-evaluation of mine communication and rescue practices. One of the hindrances of current underground communication technologies is the potential of lost or cut connections when a serious accident, such as an explosion, fire, inundation or major ground fall, takes place. The Mine Improvement and New Emergency Response Act of 2006 (MINER Act)1 mandated that each underground coal mine in the U.S. must provide for two-way wireless, post-accident communications between underground and surface personnel as well as electronic tracking of underground workers One area that has gained renewed attention in the mining sector is Through-The-Earth (TTE) communication. TTE technology has a major advantage in that transceiver devices can be carried by miners and set up quickly during an emergency, since they require no wire connection to the surface. TTE technology uses ultra-low frequency (1 to 4 kHz) electromagnetic waves, requiring relatively large wire loop antennas and highly sensitive receivers. The signal bandwidth is narrow and the permissible antenna currents in coal mines are restricted, which has led to limited usability of TTE technology in the past, as evidenced in research studies conducted by the U.S. Bureau of Mines in the 1970s. Yenchek (2012)2 pointed out that recent advances in receiver and signal processing technology have enabled voice and text communication capabilities and much improved sensitivity that offers new possibilities for TTE communication in mining applications. One company that has been developing such technology is Vital Alert Communication Inc. Vital Alert has been providing TTE communications since 2003 with a growing focus on emergency response and portable systems. The company?s Canary® Go System is one such product that looks to provide reliable communication capabilities in a portable, user friendly unit that can be utilized both for normal operation and mine rescue scenarios. Researchers at the Colorado School of Mines (CSM) have tested the Canary Go TTE communications system in the CSM Edgar Experimental Mine to determine signal propagation distances, signal quality and aspects of practical application.

Feb 23, 2014

By Daniel J. Brunner

The U. S. Department of Energy (D.O.E.) requires that the prospective nuclear waste repository in Basalt at Hanford, Washington, comply with State of California mine and tunnel safety orders. These regulations require that all main fans be installed in such a manner as to permit prompt reversal of airflow. This paper evaluates the requirement of air reversal and the appropriateness of imposing such regulations on the proposed nuclear waste repository in Basalt.

Jan 1, 1988

By M. Z. Mubarok, Z. T. Ichlas, A. T. Sugiarto, K. Sukamto

The use of ozone as an oxidant for the direct leaching of zinc sulfide (sphalerite) concentrate in sulfuric acid medium under atmospheric pressure was explored. The influence of acid concentration, feed gas injection rate, particle size distribution, stirring speed, temperature and slurry density on zinc extraction efficiency was examined. The experimental results showed that the leaching efficiency depends on all of these operating parameters except for stirring speed. It was found that essentially complete dissolution of zinc from the concentrate with the present method can be achieved in only about seven hours under the conditions of sulfuric acid concentration of 2 mol/L, particle size smaller than 74 µm, slurry density of 50 g/L, stirring speed of 420 rpm and feed gas injection rate of 1 L/min at ambient temperature. The experimental results suggest that the dissolution reactions produce independent elemental sulfur that is readily floated and can be easily separated rather than forming a layer on the surface of the reacted particle, as usually observed in a system with ferric-sulfate as oxidizing agent. It was therefore determined that the dissolved ozone play a key role in improving the rate of zinc dissolution from the concentrate. Analysis of the leaching kinetics indicate that the leaching rate follows the shrinking particle model, and the overall dissolution rate of zinc is controlled by a surface reaction.

By W. K. Choi

Using electrochemical techniques it was demonstrated that bioleaching of gold from refractory pyritic ores is a complex phenomenon. Many intermediate electrochemical reactions were found to be involved in the oxidation of pyrite, using cyclic voltammetry and carbon paste-pyrite containing electrode. Furthermore, the oxidation process was controlled by solid-state diffusion as suggested by chronoamperometric and chronopotentiometric measurements. Using the Sand&apos;s approach, the activation energy of solid-state diffusion was found to be = 22.4 kJ. After bioleaching, 96% gold was extracted from the leach resi¬due with a thiourea solution in 1 hour. A generalized model for the mechanism of pyrite oxidation has been presented.

Jan 1, 1990

By Drew Hobert, John Nielson, Erich Dohm

Metallurgical coal is an essential component for the blast furnace-basic oxygen furnace (BF-BOF) steelmaking process, which accounts for roughly 70% of total global steel production. To meet the growing demand for metallurgical coal, Arch Resources identified the potential to recover low- ash coal from ultra-fines discarded prior to the deslime flotation circuit across their portfolio of operations. Historically, many flotation circuits were designed to discard this ultra-fine coal due to high clay content and technological barriers to cost-effectively upgrade and dewater the coal to a saleable product. Recent advancements in high-intensity flotation technology, including the Eriez StackCell, have enabled coal producers to recover ultra-fine coal while minimizing capital and operating costs. In July 2023, Arch Resources commissioned the first full-scale ultra-fines recovery circuit utilizing StackCell high-intensity flotation technology at the Leer Mining Complex. This paper reviews the approach utilized to develop the flotation process design, learnings from the commissioning and ramp-up period, and performance data through the first year of operation.

Feb 1, 2025

By William Gleason

"The mining industry tends to focus on very large numbers, whether it’s talking in terms of size of deposits, tons of material mined, the equipment used or the dollars spent. The numbers associated with mining projects are often in the hundreds of millions, but sometimes it’s the little things that can have the biggest impact.Take, for example, the Rosemont Copper Project in Arizona. Owned by HudBay Minerals, the Rosemont Copper project, when in production, is expected to be one of the largest copper mines in the United States, accounting for about 10 percent of total copper production with annual production expected to be 110 Mt/a (243 million lbs/year). However, the project is currently mired in a years-long permitting process. At the 2017 SME Arizona Conference in Tucson, AZ, Kathy Arnold, director of environmental and regulatory affairs for Hudbay Minerals, spoke about the project and the efforts to get it into production.She opened her presentation with the unfortunate news that her 2017 presentation would not be that much different than the 2016, 2015 or 2014 presentations she gave to the same conference. That’s because, as of Dec. 4, 2017, the project had been in the permitting process for 3,797 days, more than 10 years. The process began when Rosemont submitted its initial mine plan in 2006 and a revised one in 2017. The official start to Rosemont Copper’s National Environmental Policy Act (NEPA) started in 2008.In June 2017, the project received its Final Record of Decision from the U.S. Forest Service, moving it a step closer to production. Yet it still faces stiff opposition from opponents while it works to secure the Clean Water Act Permit from the U.S. Army Corps of Engineers and to complete its final mine plan of operations.In her presentation, Arnold said the long process taught her many lessons, including approaching things with a different mindset. More than 130 pages worth of public comments have been collected over the years. The concerns expressed range from lighting issues to pavement to preserving land for a jaguar that was spotted on the property and named El Jefe.“A lot of things that people worry about seem to be small things, but we had to have a different mindset and be open-minded to the concerns,” Arnold said. “That is the commitment we made.”"

Jan 1, 2018

By G. Heinrichs

This paper is intended to provide information for one to be able to determine the slurry system head curve for pump applications. The slurry characteristics are the basis for what the size, material of construction, and critical carrying velocity of the pipe will be. The system head curve is adjusted by use of the pipe friction coefficient factor and slurry derate factors. An example using multi-staging of slurry pump curves is presented to compare the wear life relationship of pump parts for a tailing pipeline system head curve.

Jan 1, 1996