Search Documents

By Steve Chorley

Open-type, or main beam, tunnel boring machines (TBMs) can achieve impressive rates of production. This type of TBM typically outperforms other types of TBMs currently in use around the world. In good ground conditions, main beam machines have achieved production rates of more than 1 km/month (0.6 miles/month). However, installing effective ground support in poorer rock conditions on main beam machines can be a major cause of concern. The design of main beam machines is such that installation of ground support equipment, particularly at the front of the machine in what is commonly known as the L1 support zone, has traditionally been limited to rock drills and basic working platforms. Personnel working in the L1 zone have, until recently, been protected by roof supports and extended fingers, often with restricted access to working areas.

Jan 1, 2011

By Ray L. Tobie, Douglas E. Julin

GENERAL DESCRIPTION Block caving is a distinct caving method applied mostly to large, massive, ore bodies because of its in¬herent low cost and high production capabilities. Areas of sufficient size are removed by undercutting so that the mass above will cave naturally. Drawing of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling. When properly applied, block caving results in a lower mining cost per ton than any other under¬ground method. There are three distinct forms: (1) dividing the horizontal area into rectangular or preferably square or nearly square blocks, drawing evenly over the entire area to maintain an approximately horizontal plane of con¬tact between broken ore and caved capping; (2) divid¬ing the horizontal area into panels across the ore body, retreating by undercutting manageable areas from one end of the panel to the other and maintaining an in¬clined plane of contact between the broken ore and caved capping (thus the name panel caving); and (3) no division of horizontal area of the ore body into defi¬nite blocks or panels (this is termed mass caving). Undercutting may be from wall to wall, retreating from one end of the ore body to the other, maintaining an inclined plane of contact between the broken ore and caved capping. The total active caved area is deter¬mined by the size of block that will not produce undue stress on workings below the undercutting level and by total production requirements. This type of operation is also referred to as panel caving at some properties. SUITABLE ORE BODIES Block caving in its various forms is applicable to deposits of various shapes and ores of various strengths. Its success is governed by rigid requirements and limi¬tations. In unsuitable deposits or where improperly em¬ployed, the loss of ore may exceed that of any other mining method. Good planning, systematic work pro¬cedures, careful supervision, and good judgment con¬tribute to its success. Ore Characteristics Included as a necessary characteristic in an ore body suited to a successful block-caving operation is a proper fracture pattern. Ore hardness should be another gov¬erning factor, and the toughness or softness of the ore should be considered. There must be sufficient horizon¬tal area available for expansion of the undercut, if neces¬sary, to start the caving process. Large, massive, ore bodies usually meet these conditions. Veinlike deposits must be wide and dip rather steeply to conform to the block-caving limitations. The capping must be of such a nature as to cave when the underlying ore is being removed since the weight of the overburden aids in crushing the ore. The most favorable capping character¬istic is that it breaks into coarse pieces and resists attrition as the block is drawn. Soft capping, by breaking into fine pieces and sifting into the ore or channeling through the ore to the drawpoints, can seriously dilute the ore and hinder the extraction of clean ore from the blocks. Types of Ore In block caving, a fairly uniform distribution of val¬ues in the ore is necessary. Grade values may range from low grade to high grade, but most often the sys¬tem is applied to low-grade ores. Wide veins, thick beds, or massive deposits of homogeneous ore overlain by ground which will cave constitute suitable ore bodies. The ore must be such that it can be supported while blocks are being developed and undercut but breaks up readily when caved. Some applications include porphyry copper, disseminated molybdenite, hematite in the Lake Superior iron district, limonite deposits in northern Spain, the diamond mines of South Africa, asbestos and nickel in Canada, and massive magnetite in Pennsylvania. Size and Shape Outline of the ore body should be fairly regular, and the sides of the ore body should dip steeply. It may not be economical to mine small portions of ore extending into the walls of the deposit, and low-grade inclusions in the ore cannot be left unmined. Some dilution of the ore, as mining progresses, by low-grade or barren cap¬ping is inevitable and, unavoidably, some clean ore is left between drawpoints. Determining Cavability The use of rock mechanics is sometimes advantageous in helping to determine the cavability of an ore deposit. The US Bureau of Mines has information and testing ability which can assist in determining the cavability of ore types. Several competent consulting orga¬nizations knowledgeable in rock mechanics can also as¬sist in evaluating the cavability of an ore body. Some recent work has been done to better define the cavability index of various ore bodies; an example of how this was determined is discussed by McMahon and Kendrick (1969). The intensity of the fracture pattern is a critical parameter to be analyzed. The question to be answered is, "How intense must the fracture pattern be?" Table 1 is a tabulation of the size of rock fragments that appear at the drawpoint of various block-cave mines around the world. These are indicative of the fracture-pattern spac¬ing and, as can be seen, they vary substantially from the almost sandy material at the Mather mine to fairly sizable blocks at the Grace mine. Several sets of fractures are essential to promote good caving. Ideally, two vertical sets at nearly right angles to each other and a third set nearly horizontal are required to insure a good caving ore body. Since initial caving of an ore mass is almost always by the action of gravity acting on these planes of weakness, it is doubtful

Jan 1, 1982

Recent advances in GPS, machine guidance technology and telemetry allow an unprecedented level of control of surface mining operations. GPS technology can now locate the bucket of a shovel or the blade of a dozer within 50mm (2 inches).Some of the outcomes possible are: precise selective mining – even when the ore is visually indistinguishable from waste: tracking grade and tonnage of every ore parcel through the mine: real time productivity monitoring: detailed post accident safety analysis: tracking the movements of every piece of equipment. This paper will consider the contribution that GPS based machine control systems can make to ensuring that surface mining projects deliver the outcomes promised in the feasibility studies. Case studies of installations are presented.

Jan 1, 2004

By A. J. Richins, M. G. Nelson, R. Dunne

From the inception of flotation in the late 1800s, coarse particle recovery has been a challenge to practitioners. By the early 1900s, flotation processes included oil flotation, skin flotation, agglomeration flotation, and froth flotation, and for each there was a proliferation of flotation equipment. Ensuring good coarse particle recovery included desliming of the feed and proper conditioning were required. Froth flotation was at first used mainly to treat finer materials from grinding circuits. The maximum size for coarse particles was from 3.18 to 4.78 mm. In froth flotation, large particles with high specific gravity tend not to be recovered. Coal and minerals of low specific gravity and flaky minerals such as graphite, mica, and talc can be floated in larger sizes. In the early 1960s, the phosphate industry began using column cells to recover coarse particle by froth flotation, but early columns suffered from poor bubble generation and sanding at the flat base of the column. Recently, improved coarse particle recovery has been the object of new cell designs—the Eriez HydroFloat™, the Jord NovaCell™, the FLS coarseAir™ cell, and the Cidra P29 integrated system. The paper will follow the development of coarse particle flotation with a focus on the development, laboratory assessment, and operation of the new flotation equipment and technology designed to recover coarse particles.

Feb 22, 2026

By M. D. Lackey

The "Art" of Big Hole Drilling has been in a continual state of evolution at the Nevada Test Site since the start of underground testing in 1961. Emplacement holes for nuclear devices are still being drilled by the rotary drilling process, but almost all the hardware and systems have undergone many changes during the intervening years. The current design of bits, cutters, and other big hole drilling hardware results from contributions of manufacturers and Test Site personnel. The dual string, air lift, reverse circulation system was developed at the Test Site. Necessity was really the Mother of this invention, but this circulation system is worthy of consideration under almost any condition. Drill rigs for Big Hole drilling are usually adaptations of large Oil Well drill rigs with minor modifications required to handle the big bits and drilling assemblies. Steel remains the favorite shaft lining material, but a lot of thought is being given to concrete linings, especially precast concrete.

Jan 1, 1983

By D. A. Lindsey

Gravel lithology affects the quality of aggregate because different rock types in gravel have different physical and chemical properties. The lithologic composition of alluvial gravel reflects the composition of its source terrane and the variable effects of weathering and transport on each rock type. This report discusses lithologic controls on aggregate quality in the mountain-front environment of the Colorado Front Range. Lithologic controls on aggregate quality of gravels were evaluated using pebble count data. Gravel lithology along the Front Range shows both temporal and regional variation. The principal variable in gravel lithology is quartz plus quartzite, of which quartzite is commonly more abundant. Large quantities of metaquartzite derived from the mountain front southwest of Boulder, Colo., were dispersed northeastward during deposition of the oldest Front Range gravels. Average quartz plus quartzite is greatest in the oldest gravels. Aggregate quality is probably enhanced by large quantities of quartzite. Abundant volcanic rocks in gravel may enhance aggregate quantity, but such occurrences are local in extent. Abundant sedimentary rocks in gravel, mainly sandstone near the mountain front, may decrease aggregate quality.

Jan 1, 2002

By J. R. Heberger, B. H. Ngo

The Safety Pays in Mining v2.0 web application, developed by the National Institute for Occupational Safety and Health (NIOSH) Mining Program, helps mines determine the potential costs associated with mining injuries. This web app categorizes injury cost by part of body injured, by the cause of the injury, or by the nature of the injury. When the user selects one of over 150 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, Safety Pays in Mining v2.0 will estimate the total costs of the selected injuries and the estimated impact of total injury costs on mining company profits and will provide some examples of services and personal protective equipment on which companies could spend the savings that result from the prevention of injuries. This paper reviews the Safety Pays in Mining version 2.0 web application by discussing the development and updates to the app, how it is used to show the true costs of mining injuries, and how mines can benefit from using this app.

Feb 1, 2024

By E. McCarthy

"INTRODUCTION Talc is a hydrous magnesium silicate with the approximate elemental composition 4MgO.3SiO2.H2O. It is one of the layered phyllosilicates (like kaolin and mica) but it differs from these in that it is relatively hydrophobic. This is due to its unique crystalline structure whereby a brucite inner layer is sandwiched between silica layers and the adjacent silica layers have no interlayer bonding other than van der Waals forces. This allows talc to be sheared easily along this basal plane, and the surface is covalent not ionic. Talc occurs both as a relatively pure material (>90% talc content) and in conjunction with many other minerals in proportions all the way from 1% to 90%. At lower concentrations, it is often considered a nuisance mineral when it occurs with base metals like copper, molybdenum or nickel or with precious metals like platinum or palladium. It floats readily with these materials and often is suppressed using guar gum or carboxy methyl cellulose which will absorb along the basal surface and make it hydrophilic. Alternately if the reduced ore is hydrophobic, like MoS2, then a partial oxidation of the sulfide will convert the surface to a hydrophilic oxide and the talc can be floated away in a separate step. Talc in grades from 20 to 90% has been commercially exploited in a wide range of pigment (paint and paper), material (ceramic, construction and cosmetic), reinforcing (polymers and composites) and functional (pitch adsorbent, lubricating agent) applications. Initially these tended to be local or regional markets, but eventually with certain higher purity grades, cosmetic, polymer and ceramic applications became valuable enough to be national and trans ocean markets. TALC FLOATATION PLANTS This drove the need for higher purity grades of talc and initially this need was met primarily by ore sorting. This works well for certain deposits with well crystallized talc lenses, but for ores, such as those from widely available ultramafic deposits, where the liberation size is closer to 100 microns, sorting is not effective. That drove the need for floatation and the first investigations were published by Clemmer and Cooke of the US Bureau of Mines in 19362. The first commercial floatation plant was installed in Johnson, VT by the Eastern Magnesia Talc Co in 1937. The circuit is shown in the schematic (Figure 1). The ore was an ultramafic, serpentine derived talc; mineralogy was about 55% talc, 40% ferroan magnesite and 5% oxides, sulfides and other silicates. The oxides include hematite and chromite, sulfides pyrite and gerstorffite and silicates chlorite, serpentine and mica. After crushing, the ore was dry ball milled and then air classified to remove minus 325 mesh fines. The coarse fraction was further classified to cut at about 100 mesh and the fines from this were the feed to floatation. The -325 mesh (about 15% of the ore) was sold as a paint grade and the plus 100 mesh (about 25% of the ore) was screened to make an asphalt backsurfacing grade."

Jan 1, 2018

By William F. Daly, William H. Hansmire

Installation of initial tunnel support is often the most uncertain element of work in the design of, and a contractor bidding on, construction of a rock tunnel. The risks the construction contractor and owner assume are delineated to a great extent in the technical specifications portion of the contract documents. It is intended that this paper identify current practices for specifying initial tunnel support and the impacts each case has on the assignment of risks associated with providing the initial tunnel support. Examples of recently completed tunnel designs are given.

Jan 1, 1985

By Larry F. Drolet

Charleston, SC is anything but boring. The city was founded in 1670 and has played a significant role throughout the history of the United States. Located along the coast of the Atlantic Ocean in the southeastern United States, Charleston was a vital city in America?s early existence. Charleston?s coastal location has helped the city become the fourth largest cargo port in the United States and earn the 2011 designation as the number one travel destination in the United States by the Conde Nast Traveler Magazine. Part of Charleston?s charm and beauty can be attributed to its historic structures and churches that line nearly every sidewalk, roadways that were laid out based on the width of horse carriages, great weather, southern hospitality and coastal living. Now imagine the challenges of installing new, or re-placing aging infrastructure, in this setting. Every shovel full of dirt, every stick of pipe and every roadway sub-surface has its own historic story to tell. For engineering minded individuals, Charleston?s infrastructure has almost as fascinating a history as its more visible surface structures. Charleston was among one of the first American cities to construct separate sanitary and storm water drainage infrastructure. This concept has roots dating back to the city?s founding and is a credit to the foresight of its founding fathers who understood the basic health differences between sanitary and storm water.

Jan 1, 2013

By L. R. Moore

Arsenic is among the list of major contaminants in mining aqueous waste streams. Though the elemental form is toxic, the aqueous oxyanions are more so. The most common forms of arsenic released during mining processes are arsenate and arsenite. The common treatment technologies to date can be summed up in these major categories: oxidation, coagulation, absorption, and media filtration. These methods can often involve many expensive processing steps that may also be limited by variables, such as total dissolved solids, other cations and anions, and the oxidation state of the arsenic. An innovative technology, falling in the absorption category, was developed that can successfully reduce such aqueous forms to a level below the EPA recommendations. This new technology offers a unique and viable solution which is transparent to the above mentioned limitations.

Jan 1, 2012

By R. Fuenzalida

Since 2007, a number of Multivariable Predictive Control (MPC) Applications have been implemented on SAG mills, among others, within the Kairos Mining Concentrator Automation Program using ?Profit Controller?? and other tools comprising the ?Profit Suite??. Along this journey, several interesting and challenging issues related to SAG mill operation and control have been faced, which are relevant to be shared with the Mineral Processing community. These advanced control applications have an operational objective whose goal is to increase marginal profit on the concentrator, together with increasing mill stability. In regard to this objective, the issues to be presented and described are in direct relationship with ?Profit Controller? features and the SAG role; they are also stated and linked to get the most of the mill. Some conclusions and findings are also presented, leading to recommended practices on how to use the controller. These findings have also lead us to decide further actions to be taken on new applications to deploy and also on devising and implementing some complementary components to increase robustness of the overall automation solution, as well as reducing the need for operator intervention.

Jan 1, 2012

By A. M. El Shafey, Ahmed W. Hussein, Ibrahim M. Gaafar, Mona M. Fawzy, Mohamed Diab, Mohamed S. Abu El Ghar

The Quaternary stream sediments of the Diit area, southern Red Sea coast, Egypt, were mineralogically studied for their content of economic heavy minerals. The study area covered approximately 450 km2 and included three main parts: Wadi and Delta Diit, as well as Diit lens. The mineralogical investigation revealed that these sediments contain considerable amounts of placer ilmenite, magnetite, zircon, sphene, apatite, garnet, and rutile. Also present, in minor or trace amounts, are uranothorite, monazite, xenotime, fergusonite, khatyrkite, and gold. The magnetic fractionation tests, supplemented with the XRD and SEM mineral analyses, indicated the presence of Fe-oxide minerals as wuestite, hematite, and maghemite accompanied with magnetite as products for hand magnet separation. Ilmenite separation was carried out using a high intensity magnetic separator at a current of 1 A, while the paramagnetic minerals (e.g., garnet, pyroxene, amphibole, epidote, monazite, xenotime, and fergusonite) were separated as magnetic fraction at a current of 3 A. The non-magnetic minerals (e.g., zircon, apatite and rutile, uranophane, uranothorite, gold, and khatyrkite) were obtained at 3 A current. On a mineralogical and geochemical basis, the present work suggests that Diit stream sediments should be considered as a potential source for Ti, Fe, Zr, Zn, and Cu after the physical upgrading processes for concentrating the minerals carrying the aforementioned economic elements.

Jan 21, 2022

By Stephen M. Smading

Unique onsite assembly of a 12.43 m Main Beam TBM and back-up system was completed on September 18, 2008 in the remote mountains of the Sichuan province of China. The equipment was assembled onsite, without previously having been assembled and tested in a factory, utilizing a method called Onsite First Time Assembly (OFTA). The Jinping-II hydroelectric project features four parallel headrace tunnels approximately 18 km long, two of which will be excavated by TBMs and two by drill and blast. A nearby fifth tunnel is being excavated by a 7.2 m TBM to draw down ground water in advance of excavating the headrace tunnels. This paper addresses the following topics: ¦Project description including geology and terrain; ¦The decision process leading to onsite first time assembly, the assembly process and logistics, and lessons learned; ¦Design features of the TBM and back-up system; and ¦Operational history from startup to the writing of the paper.

By J. S. Spivey

We in the coal industry, especially in the State of Illinois, put tremendous emphasis, including time, money and effort, into on-the-job training. The results of such training and safety have been tremendous. For example, in 1981 Illinois was the first major coal producing state in the history of coal mining to have zero mine-related fatalities. And in 1985, I am very proud to say, we had the second best record in the history of coal mining, with only two fatalities. Obviously, one fatality is one too many. Our goal is, has been and will continue to be to strive for excellence. It is sad, however, that in 1981 while were were celebrating zero fatalities in the workplace, there were 21 fatalities that occurred off the job. Thus, it has become a classic American story. Success with safety has been found in the workplace, but training and preparation to prevent accidents away from the job site have almost been ignored. Accidents are the leading causes of death in the United States for all persons age 1 thru 38, and are the fourth leading cause of death for people of all ages. Every single day, on the average, more than 290 Americans are killed in accidents - a rate of one every five minutes. The leading cause of fatal accidents in the U.S. is motor vehicles. And the number two cause is home accidents. A staggering statistic is that people are being killed off the job at a rate of about 9 to 1 over those on the job.

Jan 1, 1986

By Michael J. Robison, Wojciech F. Klecan, Robert L. Horner

Since 1928, nearly 64 km (40 mi) of tunnel have been excavated within the relatively soft Cooper Group, more commonly known as the “Cooper Marl,” for water supply and transporting wastewater in the Charleston area. The majority of these tunnels are unlined and still in operation, while others collapsed shortly after excavating. Tunnel behavior and support requirements vary considerably in this material due to differences in geotechnical properties. The 4.8 km (3 mi) long, 2.4 m (8 ft) diameter Bushy Park Water Tunnel, completed in 1997 for Charleston’s Commissioners of Public Works(CPW), required no ground support. By comparison, the 1.6 km (1 mi) long, 2.4 m (8 ft)diameter Harbor Wastewater Replacement Tunnel now under construction needs continuous support close to the advancing face, despite being located in the same geological formation. Case histories and general guidelines for designing tunnels in the Cooper Marl are presented.

Jan 1, 2001

By Christopher J. Bise

INTRODUCTION The control of nuisance water in a mine is extremely important; left uncontrolled, nuisance water can have a severe effect on haulage, ventilation, production, and the health and safety of miners. To control water in mines, a four-step process is followed: (1) prevention, (2) collection, (3) transportation, and (4) treatment. This chapter will be devoted to the collection and transportation of mine water because prevention is usually dictated by pre-mining conditions and initial planning, while treatment is variable and highly site specific. A mine drainage system is nothing more than a collection of gathering points (sumps), machines that impart energy to the fluid (pumps), transportation ducts (pipes), and control devices (fittings, valves, etc.). A pump does not pull the fluid up the suction pipe; atmospheric or external pressure pushes the liquid up the suction pipe to the pump. All references in this chapter will be to centrifugal pumps, due to their popularity for mine drainage. PUMP CHARACTERISTIC CURVES The performance of a pump is plotted on a graph as an indication of its characteristic. To develop the data points, a test facility similar to that shown in Fig. 1 is established. The calibrated Venturi meter is used to measure quantity, the Bourdon gage measures pressure, and the wattmeter measures power input. Various discharge pressures are obtained by throttling with a gate valve in the discharge pipe. Quantity and power are measured at each of these pressure levels, giving the necessary data for plotting the characteristic curves. Fig. 2 shows a typical characteristic curve for a centrifugal pump. Notice that pressure is measured as so many feet of vertical water column above the outlet level, or head. Knowing the quantity (in gallons per minute), head (in feet), and power input (brake horsepower), the pump's efficiency can be plotted based upon the following relationship:

Jan 1, 1986

By Tim O’Neil

Upbeat, surprisingly so, might describe the mood at the2002 SME Annual Meeting and Exhibit in Phoenix, AZ. More than 4,000 mineral professionals gathered for three days of education, networking and product perusal. The Annual Meeting featured the theme, “Minerals for the Future@ SME” at the Feb. 25-27 gathering. Meeting attendance reached 4,039along with 479 exhibit booths show-casing 325 companies. Exhibitors found a good mix of industry types:37% from mining, 19% from processing, 20% from manufacturing and 28% from environment, education and government.

Jan 1, 2002

By William G. Pariseau

Solvay Chemicals Company mines trona in south-central Wyoming and has done so for many years. The mine is one of several in a mid-continent sedimentary basin that hosts the largest trona resource in the world. Trona is an evaporite, a sesquicarbonate that occurs in several seams of varying thicknesses and depths. Trona is processed into soda ash which has a number of industrial uses in the manufacture of glass, detergent, paper and chemicals. Figure 1 shows the location of the Solvay Mine. A ventilation shaft was recently excavated at Solvay Chemical Company’s mine in the trona patch. In fact, a 22 ft (6.7 m) diameter shaft (inside diameter) was bored upwards from the 1500 ft (457 m) level to the surface. The first bored section was 26 ft (7.9 m) in diameter that allowed for a 2 ft (0.6 m) thick concrete liner. This section began at a depth of approximately 1500 ft (457 m). A second bored section was 24 ft, (7.3 m) in diameter that allowed for a 1 ft (0.3 m) thick concrete liner. This section began at a depth of approximately 750 ft (229 m). This shaft is the #5 Shaft. Figure 2 shows the cutter head used to excavate the shaft.

Feb 1, 2025

By Steve Kral

The mining industry in Colorado faces the same problems the industry faces throughout the United States and the world — record low commodity prices and increasing regulatory and environmental restrictions that seemed designed to curtail mining activities. Despite those obstacles, the mining industry in Colorado still contributes about $8 billion annually to the state’s economy in the form of base and precious metals, industrial minerals, coal and associated service businesses and jobs. So the 300 attendees at the102nd National Western Mining Conference felt reason-ably positive about the industry in their state. The meeting is the Colorado Mining Association’s annual conference and was held at the Broadmoor Hotel in Colorado Springs in November. The theme was “Mining in the New Millennium — Achievement + Innovation = Survival.” Experts from Colorado’s mining industry and abroad discussed the challenges faced by the mining industry as it enters the new millennium. They offered insights into how the industry will operate during the early years of the 21st century and how it will survive low prices and increased regulatory restrictions.

Jan 1, 2000