Search Documents

By E. F. Schnitzer

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion. In several cases, breaches occurred between the gravel pit and the river. Initial evaluation of several sites that experienced these breaches showed that impacts to the river system were complex and varied significantly from site to site. The impacts to the adjacent river system may be viewed as positive and negative. Several flood-plain-mining sites in Oregon located in areas of historic river flow reverted to active riverbeds. In many cases, state and federal fisheries biologists and university researchers saw the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries —Mined Land Reclamation Program (DOGAMI-MLR) is studying the effects to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound flood-plain decisions regarding mining.

Jan 1, 1999

By John Gamble

This paper summarizes the weight of epidemiological evidence to evaluate the hypothesis that asbestos exposure is causally associated with increased risk of gastrointestinal (GI) cancers as suggested by Selikoff in an early study of insulation workers. This review looks at populations that develop GI cancers, namely stomach, colorectal, colon and rectal. Guidelines for assessing causality are strength of association, biological gradient and consistency of the associations. Exposure?response (E?R) was evaluated using three methods to estimate exposure. Rate Ratios (RRs) for lung cancer and percent of mesothelioma are used as surrogate measures of asbestos exposure for all the cohorts of exposed workers. Quantitative or semi-quantitative estimates of cumulative exposure to asbestos were also used to assess E?R trends and were compared to E?R trends for lung cancer and mesothelioma in individual studies. Surrogate measures are important since there are few individual studies that have assessed E?R. None of the various methods to estimate asbestos exposure yielded consistent E?R trends and the strength of the associations were consistently weak or non-existent for the four types of GI cancers. The epidemiological evidence detracts from the hypothesis that occupational asbestos exposure increases the risk of stomach, colorectal, colon, and rectal cancer. Findings are briefly summarized below. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestos; Colon cancer; Colorectal cancer; Gastrointestinal cancers; Ingestion; Lung cancer; Mesothelioma; Rectal cancer; Review; Stomach cancer

Jan 1, 2007

By Graham Davis

The future of the world's minerals industries is often painted as bleak. Peter Drucker has repeatedly proposed that the demand for minerals has become "uncoupled" from world economic growth.' This implies that, while mineral demand was in the past linked to the growing demand for and consumption of goods and services, further world development will not require substantial mineral inputs. Lester Thurow noted that for these reasons the US minerals industry is diminishing in scale and economic importance.2 There is some documented evidence of such uncoupling, and the demand for minerals may indeed diminish in the future. But such announcements are, to this point, no more than speculation. For instance, is it not just as likely that renewed environmental concerns will cause increased demand for the relatively innocuous environmental properties of metals, replacing plastics? And even if the prophesied demand decreases do occur, a sufficient fall in metal prices due to technological advances could increase the quantity of minerals demanded above current levels, in spite of leftward shifting demand curves. Thus, worldwide mineral production activity may increase or decrease in the future and no one can say whether more or fewer of the earth's citizens will become involved in the extraction and processing of minerals.

Jan 1, 1994

By Peter Campi, Harry R. Asche, Ian P. Callow, Edmund G. Taylor, P. Scott Smith

The US$1,850 million EastLink project is a 39km tollway and includes twin 3-lane,1.5km long, undrained driven tunnels. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and so to help preserve the unique flora and fauna in the area. This paper describes several of the key issues in the tunnel design and construction, including: the integration of the temporary support design with the Contractor’s tunnel excavation and support procedures, including sharing of responsibility between the Designer and Contractor for support type selection and the production of a project specific rock mass classification system to enable more objective determination of ground conditions. detailed hydrogeological assessments during the design and construction phases to allow confirmation of design loads for the tunnel lining design and the various suite of waterproofing tools in order to meet the project inflow requirements. development of a pre-cast invert solution to the main tunnel secondary lining to enable faster lining construction and to minimize risks to the tunnel membrane associated with fixing reinforcement and construction traffic.

Jan 1, 2007

By R. Hipsley, D. Arbonies, P. J. Dobak, M. Visher

The Storm deposit is a high grade breccia hosted “Carlin-type” gold deposit located at the north end of the Carlin Trend. Storm consists of 3 smaller deposits: 1) 49er Zone, 2) End Zone, 3) Discovery Zone. Structural intersections and favorable stratigraphy at the Paleozoic Popovich/Rodeo Creek formation and Bootstrap limestone formation contact are the primary known controls to gold mineralization at Storm. High grade silica-sulfide breccia occurs in the footwall of the north-south trending, dike filled, Dee fault. This mineralization cross-cuts silicified heterolithic breccia zones localized above the Bootstrap limestone where northwest, dike filled, reverse faults cut this structural-stratigraphic horizon. 40Ar/39Ar dates of 37.57+ 0.34 Ma (basalt dike) and 162 Ma (lamprophyre dike) have been obtained from dikes in the Dee pit which are locally mineralized by the same event as Storm. This paper will focus on the descriptive aspects of the Storm deposits.

Jan 1, 2001

By P. Fauvel, V. Nasri

In January 2001, French and Italian governments signed an agreement for the construction of a new Lyon-Turin railway line. This project includes a tunnel of 53.1 km length and a maximum of 2500 m overburden to be designed for a reference speed of220 km/h. The tunnel crosses major part of the West Alpine geological formations, which are very complex and contrasted in terms of the nature of rocks and the mechanical and hydrogeological conditions. In addition to the twin single-track tubes, numerous intermediary shafts, security station and intervention sites and cross passages should be built to respond to the security, operational and construction requirements. This paper describes the results of the preliminary engineering design and multiple challenges of this very long and deep railway tunnel.

Jan 1, 2005

By D. Rahal

All ores have an economic optimum particle size (Wills and Napier-Munn, 2006). This optimum value is often a compromise between the need to achieve adequate liberation for the efficient separation and recovery of valuable minerals and the energy consumed by the crushing and grinding process. It has been recognized for nearly three decades that grinding is the most expensive and least efficient stage in mineral processing (El-shall and Somasundaran, 1984). At that time it was estimated that grinding consumed between 25 and 70% of the total power required in mineral processing. This recognition drove the development of new stirred mill fine grinding technology in the 1990s (Jankovic et.al, 2003; Enderle et. al., 1997; Massey, 2008). These milling technologies have a reduced energy consumption compared to traditional fine grinding using ball mills. In the ?coarser? fine grinding applications this improvement is approximately 30%. The benefits increase to above 50% in ultrafine grinding applications (Lichter and Davey, 2006). Despite these gains, the US Department of Energy reported that an additional energy savings of up to 37% is possible in the minerals industry. They identified continuing research and development and implementing best practices in both grinding and materials handling as the primary avenues for the additional reduction (BCS, 2007).

Jan 1, 2011

By William R. Yernberg

The combined 76th Annual Minnesota Section of SME meeting and 64th Annual University of Minnesota Mining Symposium were held April 8and 9, 2003, in Duluth, MN. This year’s theme was “Stakeholders, Partners in Change.” The meeting included four keynote speakers, technical presentations and a tradeshow. Engineers, executives, mining managers and suppliers from throughout the United States and eastern Canada attended the meeting. Reflecting the theme of the meeting, all agreed that the mine owners, the government, the community and the employees are all “stakeholders.” They must be “partners in change” for the iron ore mining industry to survive in the region. Compared with past meetings, where improved technology was the primary focus, this year the focus was on the dramatic restructuring of the entire industry. As noted by several of the speakers, “This time, the change is not in technology.”

Jan 1, 2003

By Madan M. Singh

Increasingly, geotechnical data are being collected for various types of coal development projects. In many cases, a specific design concern is addressed. However, many data collection programs are not intended to immediately support mine design activities or to resolve a specific concern. The following discussion describes some current geotechnical approaches in mine planning, development of reserves, and peripheral activities. Types of Data Collection Programs Geotechnical data collection is increasingly becoming a part of standard coal exploration programs, performed along with stratigraphic evaluations and coal quality tests. The aims of such programs vary. The purpose of the exploration may be to fill out the portfolio on a block of reserves that is to be sold, leased, or held for potential future development. In such a case, a generic suite of geotechnical data are collected. The resulting engineering reports may touch on the more well known mining problems of the area, but detail may be lacking. The geotechnical data are mostly intended to enhance the saleability of the package. Mine design alternatives are generally not addressed.

Jan 1, 1985

By F. F. von Glehn

There is no doubt that simulated ventilation networks must be adequately verified before they can be extrapolated and used for predictive purposes. There are two general approaches as to how the verification can be established and these are summarised as follows; The first approach is to measure all individual branches with trailing hoses or barometers to get individual pressure drop and flow per branch and then calculate individual resistance factors for input into the software. The simulator is run, checking that the output makes general sense (check some sensitivities if possible). The network is now considered as verified. The pressure drop to be measured is relatively small and thus it is inherent that the measured set of individual K factors will be imprecise no matter how much care is taken in the measurements and the resultant simulations will inherit the same problem. In the second approach, the network is assembled using estimated (Atkinson) K factors (based on physical features of airway, past experience and catalogued typical K factors). Only the main primary flow rates are measured and hence the relative distribution of the primary ventilation in the main airways is determined (probably about 10 off primary air flow measurements). Main critical pressure differentials at main and booster fans and across critical doors are measured (probably about 6 off primary pressure differential measurements need to be made). The simulator is run and the computer model is used to iterate and select an updated suite of K factors so that the flow balances and pressure differentials are correctly simulated (typically only 2 or 3 iterations are all that is needed). The network is now considered as verified. The pressure differences to be measured will be substantial in absolute terms and can be measured with high precision. Also, because only primary flows are measured, these will generally be measured at higher air speed points and hence improved relative accuracy. This leads to more accurate simulation results. This paper examines the advantages and disadvantages of the two approaches. 1 Background

Jan 1, 2009

By Luke Erickson

San Francisco Public Utilities Commission is planning to replace 5 miles of pipeline under San Francisco Bay. The tunnel will be constructed using an Earth Pressure Balance (EPB) TBM and will be the first TBM-driven tunnel under the Bay. The alignment passes under environmentally sensitive habitats, through interbedded layers of sands and clays, and through a buried bedrock ridge. This paper discusses the geotechnical characterization and anticipated tunneling conditions and presents the analysis of various construction methods that resulted in the selection of an EPB TBM. Considerations related to tunneling with an EPB TBM are described in detail, including ground conditioners, TBM cutterhead wear, muck control, and squeezing ground.

Jan 1, 2008

By Martin Stone

Industrialized countries, particularly the United States and the United Kingdom, remain at the forefront of international efforts to control the potential disruption from computer malfunctions caused by the date change from1999 to 2000 — widely known as the millennium bug or Y2K. Disruption is least likely in the developed world, including the United States, Canada, western Europe, Japan and Australasia. However, the picture is potentially different in developing countries where many mining companies operate. The less developed the country, the greater the chance of some form of Y2K-linked disruption.

Jan 1, 1999

By Tom Martin

Mega projects present unique challenges with regard to estimating costs. With such projects, which may span decades, these challenges often begin as soon as a project is conceived. The importance of having a sound, resource based estimate avail-able early in the process cannot be overstated because it provides the basis for ongoing project decisions. For the final phase of providing an updated cost estimate, often while bidding by contractors is underway, the Engineer?s Estimate (EE) must incorporate present market conditions; account for possible volatile material price swings; be based on actual labor and fringe costs; rely on meaningful productivity rates; and accommodate any recent technology advances while identifying and allowing for risk factors. This paper explains the benefits associated with consultants adopting a contractor?s estimating approach when preparing the Engineer?s Estimate on mega projects like the various tunneling projects in New York City.

By S. K. Pan, R. Venugopal, L. A. Kumaraswamidhas, Rakesh Prasad, Chandan Pandey

Cold compressive strength (CCS) and apparent porosity (AP) of pellets are essential properties regarding the burden of blast furnaces. The optimal required values for industries are 2.5 KN CCS and 21% AP. Blaine fineness and firing temperature are the decisive parameters analyzed here. During firing, microstructure phases such as silicate, hematite, and pore are formed. The phase’s grain density during induration influences the pellet’s CCS and AP. The influence of the factors over the response is evaluated by I-optimal (response surface methodology) design. Blaine fineness, firing temperature, pore phase grain density (PPGD), silicate phase grain density (SPGD), and hematite phase grain density (HPGD) affect the CCS and AP of pellets. The RSM-I-optimal predicted responses with a coefficient of determination (R2) of 0.89 for CCS and 0.91 for AP of iron ore pellets. Optimal conditions were Blaine no. = 1668 cm2/g, 1250 °C firing temperature, PPGD value 90 no/mm2, SPGD value 250 no/ mm2, and HPGD value 490 no/mm2, with 4.5 KN CCS 27%. The induration processes were investigated through statistical design of experiments for process optimization. Statistical analysis indicated the direct and interactive influence over CCS and AP. In this study, RSM-I-optimal modeling is used for iron ore pellets processing. The I-optimal prediction could be applied to make the process economical because information is obtained through fewer experiments.

Aug 18, 2020

By Derek J. Penrice

The Caltrain Downtown Extension (DTX) project will extend commuter and future statewide high-speed rail service into the Transbay Transit Center, which will be located in the business district in downtown San Francisco. The DTX project includes 1.5 miles of underground construction, comprising complex sections of mined and cut-and-cover tunnel. As part of the DTX preliminary engineering process, development of appropriate contracting practices, including contract packaging, procurement methods and contract terms for the underground construction, has been initiated. This paper provides a summary of the evaluations undertaken, preliminary conclusions reached, and proposed next steps to promote industry interest and maximize bid competition.

Train services through the Channel Tunnel linking Britain and France where scheduled to be fully restored in February 2009 following several months of repairs after a major fire in the tunnel on Sept. 11, 2008. A lorry caught fire on a shuttle train carrying heavy goods vehicles bound for France through the 50-km- (31-mile-) long northern tunnel. The fire, that spread to other vehicles, raged for about 16 hours. The extreme temperatures of up to 1,000º C (1,832° F) caused extensive damage to about 600 m (2,000 ft) of the 7.6-m- (25-ft-) diameter tunnel?s concrete lining, approximately 11 km (7 miles) in from the French entrance. The Channel Tunnel operator, Eurotunnel, awarded the repair con-tract, estimated to be between ?50 to 60 million, to a consortium of Freyssinet, Eurovia Travaux Ferroviaires (ETF) and Vinci Energies. Freyssinet was appointed to look after the civil engineering works, while ETF would be responsible for track and overhead wire restoration and Vinci Energies responsible for other equipment. The technique of hydrodemolition, which uses high-pressure water jets to remove concrete from various structures, was specified as the method to remove the fire damaged concrete. Freyssinet subcontracted the concrete removal to the specialist hydrodemolition and industrial cleaning contractor Philip Lasserat.

Jan 1, 2009

By Thomas V. Falkie

In bygone days, the mineral engineer spent most of his/her time on the technical aspects of designing, building, and managing mineral operations. In the last few decades, mostly since the 1960s, increasing amounts of engineering man power and time are spent dealing with federal, state, and local government agencies, laws, and regulations. It is not possible to plan, design, build, or operate mines, mills, smelters, or even office buildings without detailed consideration of government regulations and permitting requirements dealing with environment, worker health and safety, etc. The four chapters of this section provide an overview of the social, legal, political, environmental, and health and safety aspects of mineral enterprise. The section sets the stage for the working engineer/geologist in industry, government, consulting, or academe and points the direction for more detailed study in each of these areas.

Jan 1, 2008

By Gregory T. Ziegler

A complex soil profile and high water table, together with a below-grade active subway tunnel, an above-ground elevated railway line, and the heavily travelled Northern Boulevard all passing above the tunnel alignment, combined to make mining of New York?s Northern Boulevard Crossing what is widely considered to be the most challenging portion of the multi-billion-dollar East Side Access project. The Northern Boulevard Crossing is a vital link in this project which, when completed, will connect the Long Island Railroad to Grand Central Terminal in Manhattan. How the sequential excavation method (SEM) tunneling was successfully accomplished, despite the obstacles, was a textbook exercise in practical innovation coupled with close cooperation between the owner, the construction manager, Hatch Mott MacDonald, the designer, Parsons Brinckerhoff, the contractor, Schiavone-Kiewit, and spe-cialty geotechnical contractor, Moretrench.

Sep 1, 2013

By Robert C. Bates

Published information discussing uranium mine radon daughter controls and related costs was examined and used to develop an estimated (projected) cost per ton for any level of control. Results show a clear power function increase of cost for conventional dilution ventilation as the annual exposure limit is lowered. Projections can be made using any assumed changes in consumer price index (CPI) and radon daughter working level months exposure limit. Bounds on the estimated costs are provided, and applicability of the final equation is discussed.

Jan 1, 1983

By Robert C. Horton

The Getchell Mine is located on the east flank of the Osgood Mountain Range in the Potosi Mining District, Humboldt County, NV. Mining in the area first began in 1883 for copper, lead and silver in skarn-related deposits. Tungsten was discovered in the skarns in 1916 and was mined sporadically until 1957. The first major discovery was made in 1933 when two Winnemucca prospectors, Edward Knight and Emmett Chase, found gold at the present site of the Getchell gold mine. In 1934, after a small amount of preliminary prospecting, the claims were purchased by Noble H. Getchell of Midas, NV. The Getchell Mine Inc. was organized and exploration and development work began on a broad scale. Major funding was provided by George Wingfield and investors he assembled. Laxalt described Wingfield’s immediate history prior to his financing of Getchell as follows.

Jan 1, 1999