Search Documents

By F. E. Heuze

This article deals with the effects of high-explosive and nuclear explosions in rock masses. We first highlight the strong influence of geological discontinuities, such as joints and faults, on ground motion characteristics. Then, we briefly introduce the Discrete Element Method, as a new technique for numerical simulations. II is shown to be far superior to continuum-based approaches, when dealing with the dynamics of discontinuous media such as jointed rocks. Finally, we simulate the ground effects from a generic contained nuclear explosion, which bears some similarity to the SHOAL event in granite. This calculation is intended to emphasize the influence of the near-source geology on the distribution of energy, and on the motion at various azimuths in the medium.

Jan 1, 1991

By W. R. Reed, G. W. Luxbacher

As directed by the MINER act of 2006, the NIOSH Office of Mine Health & Safety Research (OMSHR) has annually awarded contracts to enhance mine safety and health. OMSHR has a history of research that focuses on both respirable coal mine dust and respirable crystalline silica (or quartz) dust, and contracts have been awarded since 2010 in support of our intramural research efforts. In 2018, a National Academies of Science consensus study report recommended expansion of respirable dust research. As a result, beginning in 2018 through 2021, eighteen contracts were awarded focusing on this area. These contracts can be grouped in three topic areas: characterization of coal/dust, development of real time monitors, and improvement of respirable dust controls. This paper summarizes the outcomes of completed contracts and the progress of current contracts.

Mar 2, 2022

By Ray Hutton, Darrell Liebno, Taro Nonaka

Background Population growth and increasingly stringent regulatory controls on water quality across North America have resulted in municipal governments investing heavily in infrastructure to control what are known as Combined Sewer Overflows (CSOs).These are events which occur when combined sewers exceed their conveyance capacity during periods of heavy rainfall or snowmelt. The city of Atlanta, Georgia is one such municipality; with a population of over450,000 within city limits and a sewer system servicing 1.2 million including adjacent jurisdictions, the City of Atlanta has a Combined Sewer System (CSS) encompassing approximately 15% of its total 3,540 km (2,200 miles) of sewers. Atlanta’s CSO discharges to local watercourses began to draw fire from environmental groups in the1980s. As a result, in the early 1990s, the City constructed a series of CSO control facilities which provided screening and chlorination at seven CSO discharge points across the CSS watershed. Unfortunately, these facilities were not capable of handling all of the overflows generated due to heavy storm events; frequently, untreated water was bypassed around the treatment facilities. The federal Environmental Protection Agency (EPA) deemed that water quality standards were being violated by these discharges, and a suit was brought against the City to force a higher standard of compliance. As a result, the City entered into a federal Consent Decree which would bring CSOs into compliance with federal standards by 2007. A critical component of this plan was the design and construction of the West Area CSO Tunnels and Pumping Station. In February 2003 the City’s Department of Watershed Management retained the services of Jordan Jones & Goulding/Hatch Mott MacDonald/Delon Hampton Associates (JDH Joint Venture) to design and provide construction management ser-vices for the project, which was designed to capture combined sewage from three of the City’s existing CSO facilities on the northern end of the CSS watershed. The design consisted of two connected tunnels which would convey the wastewater originating from the North Avenue, Clear Creek, and Tanyard Creek CSO facilities to a submersible wet well pumping station located at the R.M. Clayton Water Reclamation Center (WRC). Since the majority of the effluent stream consisted of storm water, the City elected to design and construct a separate treatment plant. This plant was designed under a separate contract, and is currently under construction.

Jan 1, 2007

By J. M. Elder, W. S. Kow

Challenges to new heavy mineral deposit developments are presented. These include land use issues, particle fineness, declining grades, and particle coating, amongst others. Industry responses to these are presented as possible solutions.

Jan 1, 2005

By Warren H. Weisz

A cement, in the broad sense, is any substance which will cause various materials to adhere to each other. Clay was probably the first material to be used by man as a cement or binding agent. Water occurs in or is mixed with the clay to make it plastic, so that it can be formed in place. The sun and air remove the water from the clay and on drying strength is developed. The clays unless fired are not too resistant to water, therefore, their use is best when restricted to dry areas. Gypsum used as a cementitious material is not the subject of this paper, but its use dates back thousands of years. Gypsum mortars were used by the Egyptians in building such massive masonry structures as the pyramids. The Egyptian mortar consisted of a mixture of sand with burned gypsum (of an impure type of 81.5 per cent calcium sulphate and 9.5 per cent calcium carbonate) for the cementitious material. The burning of this type of cementitious material took place at relatively low temperature. These burning reactions will be covered later when the dehydration of gypsum is discussed. The setting of the partially dehydrated gypsum is considered to be crystallization from a supersaturated solution which deposits crystals of dihydrate (gypsum). In low water-content mixes, the interlocking of the needle-like crystals helps to produce higher strengths. Slaked lime made from limestone burned at higher temperatures (1648 F is generally considered as the calcining temperature, although under certain conditions incipient calcination will take place at 1250 F) is another early-period cementitious material. During slaking with water, a colloidal or amorphous hydrated lime is formed. When it is allowed to dry, it hardens and develops low strengths. On exposure to the carbon dioxide of air in the presence of some moisture, carbon dioxide is adsorbed and part of the calcium hydroxide is converted to calcium carbonate. Structures in which a lime mortar is used continue to grow in strength as this reaction proflesses. Hydrated lime has the disadvantage of not setting under water.

Jan 1, 1960

By Faruk Oksuz, Dave Schiemann, Matt Trotter, Mike Padilla, Carmen Scalise, Miquel Sanchez

"The McCook Main Tunnel system consists of a 10-m (33-ft) finished diameter, 490-m (1,600-ft) long, hard rock tunnel constructed from a 27.5-m (90- ft) diameter and 92-m (300-ft) deep main gate and tunnel construction access shaft. The gate shaft houses six, high-head 4.4 m by 9 m (14.5 ft by 29.5 ft) wheel gates to be installed in the bifurcated and steellined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir.The construction of the tunnel system has been divided into two contracts. The gate and construction access shaft was completed in August 2011. The tunnel excavation and concrete and steel lining was completed in September 2014. The remaining and undergoing construction include the tunnel connections to the reservoir and the Mainstream Tunnel and installation of gates and hydraulic cylinders. This article focuses on the live connection of the McCook Main Tunnel to the Mainstream Tunnel that was initiated in November 2014 and will continue through the seasonal drier weather conditions in Chicago approximately from October through April. Chicago TARP systemThe MWRD has been addressing combined sewer overflows (CSO) and flooding in Chicagoland since the late 1960s and formally adopted the tunnel and reservoir plan in 1972 to protect the region’s most precious drinking water supply, Lake Michigan. Phase I of TARP, which included construction of 175 km (109 miles) of deep storage and conveyance tunnels with diameters up to 10 m (33 ft), was completed in 2006. In addition to protection of Lake Michigan from CSO discharges, Phase I resulted in substantial improvements in surface water quality as well as the quality of life for lake and riverfront communities in Chicago. Water quality improvements and flooding mitigation will be further enhanced as Phase II reservoirs are placed in service, including the three large reservoir systems, McCook, Thornton and Majewski (Fig. 1).The McCook Reservoir is the largest reservoir in the TARP system. Once completed, this $700-million reservoir facility will receive 38 billion L (10 billion gal) of CSO and flood water via the McCook Main Tunnel, which connects the TARP Mainstream Tunnel to the McCook Reservoir, and from distribution and Des Plaines inflow tunnels which will bring flow from the Des Plaines Tunnel of TARP."

Sep 1, 2016

By G. B. Glass

In 1996, 92.5% or 233 Mt (257.4 million st) of coal produced in Wyoming came from the Wyodak coal zone in the eastern Powder River Coal Field. While the mined portions of the zone consist of one to three beds of coal with an aggregate thickness between 15 and 33.5 m (50 and 110 ft), the thickest expression is 61 m (200 ft). The delivered coal from this zone averages 0.33% sulfur, 5.12% ash, and 19.98 MJ/kg (8,590 Btu/lb). This coal zone occurs at or near the top of the Paleocene Fort Union Formation, which is overlain by the Eocene Wasatch Formation. There is also production from two coal beds in the lower portion of the Wasatch at the southern end of the basin. Production of coalbed methane derived from the Wyodak coal zone is currently an estimated 10.2 billion cu ft a year. This production is occurring just west and downdip from the coal mines and is increasing each year.

Jan 1, 1998

By Yongsik Jeong, Kwangmin Kim

Most tailings storage facility (TSF) failures occur in active, upstream-type TSFs, often due to extreme and unexpected weather conditions—specifically, heavy rainfall and strong winds. This case study of a TSF in southern Arizona examines the use of the optimum safe beach distance (Doptimal, the optimum distance between the crest and decant pond) as a tool for monitoring geotechnical stability and reducing catastrophic failures. A digital model of the TSF was used to determine the critical beach distance (Dcritical) under normal weather conditions, and Doptimal was then determined by adding incremental distances to account for the effects of heavy rainfall (Drainfall) and strong winds (Dwind). To overcome accessibility issues, a drone was used to map the TSF geometry and create a digital model. This model served as the basis for conducting a coupled stress-seepage, finite-element (FEM) analysis with a safety factor of 2.0 to assess geotechnical stability (Dcritical). The safe beach distance increments were determined using the PMP (probable maximum precipitation) and possible maximum wind speed. Based on this analysis, the optimal safe beach distance at the study site was identified as 202.2 m. Since the current beach distance (371 m) exceeds this value, the TSF was considered to be stable and satisfied the design safety factor of 2.0. However, this distance should be reassessed periodically to account for changes in the TSF geometry and other conditions. Furthermore, it applies only TSFs that are well-managed and feature a smooth, non-undulating beach surface with a consistent slope.

Cement in 1975 indeed did operate in an unfriendly environment. World recession, escalating costs, fuel crises, reduced product demand . . . . all led to market conditions detrimental to industry profit margins and investment re turns. During the year plant utilizations fell, break-even points were raised, and competitive moves introduced to move built up inventory levels. A number of cement plants were temporarily taken out of production to help alleviate specific situations. Meanwhile, under resultant financial pressure, several companies omitted dividend payments, changed their top executives, and reorganized and reduced staff overheads. It was a difficult year for cement, yet a much more ominous note was sounded in permanent plant closings. Four more cement operations were shut down in 1975; to date in 1976 we know for sure of three additional plant closings, while rumour has it that at least one more may not be in production by year-end. The somber feature is found within the descriptions of the closed facilities, and in the stated reasons for their being taken out of cement manufacture.

Jan 1, 1976

By Omid Asghari, Amin Mousavi, Arshad Ranjbar

Geometallurgical modeling of the production benches is an attempt to estimate the geometallurgical variables of the different ore domains, which leads to a better understanding of the ore and its properties. Having geometallurgical variables results in a more accurate prediction of ore characteristics, an improved drilling and blasting operation, and better efficiency of the processing plant. In this research, the geometallurgical variables required for the geometallurgical modeling of the extraction benches are discussed. Then, the relations between Bond work index (BWi), as one of the most important geometallurgical variables and the primary grindability index, and rock geomechanical properties are investigated based on the previously published studies. The BWi is the main parameter for measuring the resistance to the grinding of ore minerals. It represents the energy required for processing (e.g., crushing, grinding) ore rocks in the beneficiation plant. As a real case study, BWi of a production bench in Sungun Copper Mine, located in East Azarbaijan province, Iran, was estimated. The rock’s geomechanical properties were measured using laboratory tests, including uniaxial compressive strength, Brazilian tensile strength, point load strength, and hardness. Then, BWi was estimated using the proposed formulas in the literature and the results of the rock’s geomechanical properties. The selected bench consists of three ore zones and two dyke domains. The laboratory tests revealed that the first ore zone has a slightly higher compressive strength than the other two zones, while the compressive strength of the waste rocks is larger than the ore domains. Using the proposed equations in the literature, the predicted values of the BWi for the samples in ore zones are in the range of 6.36 – 14.44 (kWh/t), and therefore this wide range must be considered when the short-term production schedule is planned. In addition, variations are observed in the samples within a specific zone and between the ore zones, demonstrating heterogeneity in the selected bench. Finally, wide-open results obtained by different equations show a necessity to perform a geometallurgical program specifically for the Sungun mine.

Oct 28, 2021

By J. Trow

Dowsing is really IESG which inductively locates electric gradients (dv/dx) on the flanks of SP anomalies. "Sensors" are in one?s head. The "meter" consists of one?s body, limbs, and two $.69 welding rods. The method was calibrated near Mamainse Point, Ontario, where IESG-negative chalcopyrite-bornite-chalcocite-native copper ores reveal mineral zoning related to the IESG-positive Keweenaw fault, down which oxidizing solutions moved. In Michigan, the IESG-positive Keweenaw fault suggests that oxygen-bearing solutions from the Jacobsville Sandstone moved downward to oxidize hydrothermal sulfur to produce native copper, and to supply sufficient water to satisfy Walter White.

Jan 1, 1992

By Christos Roumpos, Philip‑Mark Spanidis, Francis Pavloudakis

Coal mining operations are large-scale, long-term frameworks of high complexity. Mining organizations accumulate, develop, and leverage knowledge from diverse scientific and technological fields as a result of these operations. Both practical experience and existing literature indicate that knowledge management (KM) methods within the mining industry primarily target solving immediate technical challenges and operational requirements. However, they are not commonly regarded as strategic tools to enhance the performance and competitiveness of mining companies. Empirical evidence from the Greek mining industry suggests that the management of available knowledge is intricate, less effective, and dysfunctional. This paper presents a methodology based on the principles of quantitative research (QNR), collaboratively conducted with a group of mining experts, to assess the KM landscape in the Greek mining industry. The methodology involves a structured data collection framework using questionnaires, subsequent statistical analysis, a discussion on critical methodological aspects, and an interpretation of results focusing on key aspects useful for planners and designers of KM systems in the mining industry. Finally, the paper concludes by summarizing the methodology’s outcomes and proposing further perspectives for research.

Mar 16, 2024

By H. Demirel

This paper deals with concentration of hematitic-limonitic iron ores. The ore sample obtained from Karakuz (Turkey) contain:. about 40-46 I Fe. First, a low intensity magnetic separation process was employed to separate the strongly magnetic particles cf "-10+2 mm" and "-2+0.075 mm" size fractions and magnetic concentrates with 59.1 % Fe aid % 58.0 Fe were obtained respectively. The non-magnetics of both fractions were then fed to a nigh intensity permanent magnetic separator. The Fe contents of "-10+2 nun" and "2+0.075 mm" size fractions were increased from 28.2 to 51.13 and from 35.4 7. to 43.25 respectively after single pass. Easing on these results, it was concluded that the high intensity permanent magnetic separator could he used as a pre-concentrator f.7.1- hematitic-limonitic Karakuz iron ore.

Jan 1, 1991

By R. Larry Grayson, Ahmet Unal

Use of radio frequency identification (RFID) technology to solve informational needs in isolated and restricted underground mining environments will be reviewed, giving specifications of some past and currently available systems. The advantages and disadvantages of using various frequencies, system configurations, and specific components, including their construction standards and capability, will be discussed. The remaining challenges to more widespread use of RFID systems for personnel and vehicle tracking will be identified, and recommendations concerning operating environment capabilities will be detailed. Finally, the ultimate requirements for maintaining system integrity during and following a coal mine emergency will be discussed.

Feb 24, 1997

By Amy McBrayer, Andrea Brickey

Area mining is a surface mining method that allows for efficient mining and contemporaneous reclamation of tabular or bedded deposits, e.g., coal. Mine planning methods for area mines differ from those of open pit metal mines. Area mines in the Powder River Basin (PRB) use various processes for mine planning at both the strategic and tactical stages. With the ever changing commodity markets, it is becoming increasingly important for mine operators to be able to react quickly to the changing business environment. Tools that allow for the development and rapid comparison of production schedule scenarios are key to ensuring agile mine operations. A survey of mine engineers responsible for mine design and production scheduling at coal operations provides clarity on the current mine design and production scheduling processes in the PRB, as well as a discussion on potential solutions to upcoming challenges. In this article, we describe various mine planning processes used by the coal producers in the Powder River Basin. The survey identifies a clear gap in the ability to create comprehensive schedules associated with limited tools and lack of engineering labor needed to frequently conduct the mine design and scheduling process.

Jul 8, 2023

By C. A. Young

In-situ Fourier transform infrared/internal reflection spectroscopy (FT ?IR/IRS) has been extended to study oleate adsorption at a calcite surface. The birefringent and transmission limitations of calcite were overcome by using an appropriately designed optical setup and a near-infrared (NIR) spectrometer. An adsorption isotherm was determined at pH 9.2 and room temperature. Comparison with the fluorite/oleate adsorption isotherm determined by the same technique indicates that oleate abstraction by calcite can be as much as one order of magnitude larger than that by fluorite. Nevertheless, the hydrophobicity of the fluorite/oleate surface is greater for equivalent adsorption densities as indicated by contact angle measurements and flotation results. The monolayer region has been confirmed to be chemisorbed oleate at both calcite and fluorite surfaces. Furthermore, multichannel laser Raman spectroscopy (MLRS) showed that chemisorbed oleate at the fluorite surface undergoes a double-bond reaction with oxygen to form an epoxide/polyether complex. Such a reaction, however, could not be detected at the calcite surface. These phenomena are discussed in terms of the intrinsic surface properties of the mineral systems as well as the adsorption density and the cross-linking/polymerization reaction of the adsorbed oleate film.

Jan 1, 1993

By T. J. Batchler, K. M. Mohamed, D. F. Gearhart, R. K. Zipf

Seals are explosion-resistant structures built in underground coal mines to isolate abandoned mining areas from the active workings. An equivalent single degree of freedom (SDOF) method such as the single-degree-of-freedom blast effects design spreadsheet (SBEDS) developed by the U.S. Army Corps of Engineers can be used to design seals to resist mine explosions. The critical input for the SDOF code is the seal resistance function. The objective for this study is to develop engineering data for design of plain concrete (PC) and reinforced concrete (RC) seals using finite element (FE) models. The FE models can then be used to generate resistance functions for different PC and RC seal designs, which can be used in the SDOF codes. The U.S. National Institute for Occupational Safety and Health (NIOSH) researchers designed and built a test fixture for use in conjunction with NIOSH’s Mine Roof Simulator to apply a four-point bending load on the face of the tested seal. Eight large-scale experiments for each PC and RC seal were conducted. The experimental design considered the effects of the foundation strength, hitching and roof-to-floor convergence. Calibrated FE models for PC and RC seals were developed using ANSYS Ver. 13. With a very limited number of engineering-based assumptions and a single set of data—including Young’s modulus, compressive strength, stress-strain relationships, etc.—the PC and RC seal models successfully calculated the recorded resistance functions and failure patterns for a wide range of boundary conditions. Plug and RC seals were assumed for a 1.83-m- (6-ft-) high entry to demonstrate the application of the calibrated finite element models for calculating the resistance functions of these seals. The resistance function of a particular plug seal case was found to be a bilinear relationship. The resistance function of a particular RC seal without shear reinforcement was found to be a nonlinear relationship.

Jan 1, 2013

By Jennifer L. Bell, PATRICK L. YORIO, Emily J. Haas, Susan M. Moore, Lee A. Greenawald

Although researchers have struggled to replicate Heinrich’s safety triangle findings (Heinrich 1931) for various reasons (e.g., no access to his original database and it is unclear if the database was of a single establishment/operation or for an entire industry), the occupational safety community has continued to adopt and expand the applications of this theory (e.g., McSween 2003). Within the mining industry, the potential exists for operations and companies to use concepts from the safety triangle as a way to inform or challenge the practices employed within their health and safety management systems (HSMS) to prevent incidents (Backlund 2016). This paper considers data obtained from the Mine Safety and Health Administration’s databases and demonstrates the validity of applying the safety triangle theory at the mine level. The results support the use of this theory and demonstrate that lower severity incidents can predict fatalities in a subsequent year where significant nuances and caveats to applying the theory are identified and discussed.

Jul 25, 2020

By MATTHEW HART, THOMAS BAMFORD, Kamran Esmaeili, MICHAL KOWALCZYK, FILIP MEDINAC

Improved haul-road conditions can have a positive impact on mine operations, resulting in heightened safety, productivity gains, longer tire life and lower maintenance costs. For these reasons, a monitoring program is required to ensure the operational efficiency of the haul roads. Currently, at Bald Mountain Mine, monthly site severity studies, ad hoc inspections by frontline supervisors or operator feedback reporting are used to assess road conditions. These methods are subjective and provide low temporal resolution data. This case study presents novel unmanned aerial vehicle (UAV) technologies, applied on a critical section of haul road at Bald Mountain, to showcase the potential for monitoring haul roads. The results show that orthophotos and digital elevation models can be used to assess the road smoothness condition and to check the road design compliance. Moreover, the aerial mapping allows detection of surface water, rock spillage and potholes on the road that can be quickly repaired/removed by the dedicated road maintenance team.

By W. P. Arnott

This paper presents real time photoacoustic measurements of diesel-soot black-carbon (BC or EC) and Dusttrak nephelometer total carbon (TC) concentrations in a Nevada gold mine. Comparisons with time-integrated filter-based measurements of EC and TC accomplished using the NIOSH 5040 method were found to be 50% smaller than the integrated real time measurements. This work was initiated primarily as a demonstration project for the usefulness of photoacoustic instruments in measuring BC in the mine environment. Real time black carbon measurements are very useful for determining miner exposure, for providing feedback in mine ventilation systems, and for quantifying machine specific emission rates to understand the operating conditions for specific machines that produce greatest black carbon concentrations. This paper reports real time measurements of DPM from a loaded and empty hauler as it is operated in a drift with a 12% grade. The photoacoustic instruments were demonstrated to be satisfactory for BC measurements in the mine environment.

Jan 1, 2009