Search Documents

By V. Eu. Anufriev

Despite of significant cost advantages and the positive expierence roof bolting is limited up to 15-20% of all workings at the Cuzbass mines. The low level of application of the technology is the result of specific mining and geological conditions and defects of organization and technical support. When analysing mining and geological conditions of development working maintenance and geomechanical aspects the necessity of changing of technological schemes of preparation and extraction of mine sections is obvious. The prospects of large-scaled transferring from frame support to roof bolting are connected with introduction the technology of support with the help of non- expanding bolt classes including bolts with mineral filler fixation. The design of bolters with mineral filler fixation is given here. The results of testing of bolt load characteristics in artificial holes and in situ are proved the technology efficient. For increasing of drilling works efficiency it is necessary to master the production of oilless compressor and heading machines with the manipulator. For bolt dimension forecast it is recommended to use the relations of measured parameters of "dome" to roof shifts. Effective monitoring of rock pressure in the junctions is connected with the use of support of conventional bolts together with bolts of deep installation with simultaneous supporting of face ends with special mechanical sets, which compensate face length change.

Jan 1, 1996

By Anthony Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990?s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine?s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

Jan 1, 2007

By Robert G. Harris

During the last five years there have been significant improvements in face support monitoring techniques particularly in respect of face pressure. The measurement of support loading pressures was originally conceived as a maintenance aid for the hydraulic systems but recent work has also included geological loading displays of the complete face as well as individual supports. This paper briefly examines the means of obtaining this information, together with some examples of actual face data. Also included is a summary of the benefits of such monitoring and an outline of future development work.

Jan 1, 1993

By Tim Ross

Several shear failures were observed in Shaft #1 at the Mountain Coal Company, LLC, West Elk Mine, after mining longwall Panel 23, 1,100 ft to the east of Shaft #1. It was speculated that this shear damage could be related to differential ground movement caused by in situ stress relief from the ?stress shadow? of the caved zone above longwall Panel 23. A numerical study was conducted to assess the possibility of the shaft shear damage being caused by in situ stress relief and the potential for additional damage to Shaft #1 and two other nearby shafts, due to mining nearby longwall Panel 24. Three-dimensional (3D) models were built in FLAC3D to simulate past and future mining near shafts, the estimated local anisotropic and directional horizontal stresses, and the overlying variable surface topography. The numerical analyses indicated that stress relief due to mining Panel 23 caused the shear damage to Shaft #1and that additional damage to Shaft #1 and the other two shafts, would likely result from mining longwall Panel 24. Additional shear damage was documented in Shaft #1 when longwall Panel 24 was mined, confirming the results of the numerical analyses.

Jan 1, 2006

By Stephen C. Tadolini

PC-Strand tendons, commonly referred to as cable bolts, have become a major rock reinforcement device for underground mining and civil applications. The most common configuration is a 1+6 strand, which designates a center king-wire, with six outer wires wound around it to form a 0.6-in (15-mm) diameter cable. The capacity of this tendon approaches 30 tons, but the performance is largely dependent on the anchorage medium and the ability of the system to transfer stresses back into the rock mass while reinforcing and suspending the immediate roof. Recent developments to improve the transfer mechanisms of the PCstrand via the anchorage medium by impregnating the individual wires with uniquely designed deformations have resulted in improved anchorage and subsequent cable bolt performance. This paper describes a series of laboratory tests used to develop the initial indentation patterns and numerical modeling simulations that were undertaken to refine and optimize the final designs. The new, indented PC-Strands, offered in both bright and properly galvanized, have been tested in the field and are being used effectively in two new cable bolt products. The results of the laboratory, computer modeling, field testing and in-situ installations provide a glance at the next generation of cable bolts. This suite of testing shows how they will improve the safety and serviceability of openings under adverse ground conditions.

Jan 1, 2012

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By H. C. Li

Mechanical models are established in accordance with the degree of mining on both sides of the coal pillar, and formulae were derived which calculated the superposition stress distribution and the width of the plastic region. The stability of the coal pillar was analysed and a reasonable size of coal pillar determined, in accordance with the elastic region rate. Further practical examples for the stability of the coal pillar are calculated and simulated.

Jan 1, 1992

By Yingxin Zhou

Virtually every coal seam in Appalachia will at some time be subject to multi-seam interaction (Wu et al, 1987). Many such problems result from seams which lie in close proximity or have split and lie within thirty feet vertically of one another. Existing techniques for multi- seam design have concentrated on conditions where the entire inner burden is not the failing member and are unsuitable for ultra-close multi-seam design. Structural integrity of the inner burden must be maintained if two superimposed seams are to be mined separately and under- standing possible failure mechanisms of the inner burden is an essential first step in the design process.

Jan 1, 1989

By Holger Witthaus

Beside the traditional geomechanical evaluation methods the geotechnical parameters are recognized as important facts of the planning work for multiple seam mining. Standards for applied monitoring and investigation methods for geotechnical determination of drill cores, laboratory rock-tests and observation of roadheadings are the basics for rock mechanics classification and support design. The geomechanical classification is in this context an essential element. The planning procedure, as it is becoming more and more detailed, beginning with the panel layout up to the technical instructions of roadway development and design of roadheading machinery, nowadays uses a lot of geotechnical information that also are expanding to include quantitative determination of more parameters. The current monitoring system includes the description of separation planes using drill cores and roadheading observation as well as laboratory tests of rock-strength and geophysical borehole examinations. This information is analyzed within the geomechanical standard-classification. The re-engineering process of comparison the predicted support success to the actual monitoring results provides the opportunity for continuous optimization of the planning work und support design. This way of empirical analysis is used for basic planning work in Germany for decades. But using the technical standard of information technology and a centralized database now it is possible to reach quick-win effects in implementing research results on the one hand and actual experiences on the other hand.

Jan 1, 2006

By Swapan Bhattacharya

United States federal and state regulatory authorities require underground mine operators to adopt adequate measures to minimize material damage to the surface caused by nine subsidence. This paper presents an approach to define and determine the extent of material damage due to subsidence from underground coal mining. The basic steps involved in the development of adequate criteria have been enumerated together with the approaches and methodologies used.

Jan 1, 1984

By Peter Zhang

Pumpable cribs are being increasingly used in longwall tailgate entries and bleeders for roof support under abutment pressure. Their high peak capacity and confinement-controlled yield characteristics from reinforced-bags make them relatively safe and reliable standing supports for highly productive longwall panels. The pumpability of crib material over a long distance from the surface greatly reduces material handling and makes the underground installation more efficient and flexible. However, the performance of pumpable cribs is dependent upon crib properties, crib pattern, quality of installation, and geological and mining conditions. For proper crib selection and safe support design, it is critical to understand the basic technical requirements and performance of pumpable cribs in longwall tailgate entries and bleeders. Based on more than 10 years of experience using pumpable cribs for longwall standing support, the requirements and performance of pumpable cribs in longwall tailgate entries and bleeders under different mining conditions are presented. Experience shows that the load-displacement curve from full-scale lab testing is a good indicator of pumpable crib suitability for certain applications. Crib peak capacity, stiffness, and residual characteristics define its applicability to certain gate entries and bleeders under different cover depth. Crib pattern and spacing can be determined by abutment pressure level, roof, floor, and rib conditions, local roof stability, and ventilation requirements. To achieve proper in-situ performance, quality control of crib installation is also important.

Jan 1, 2012

By Pengfei Wang, Guorui Feng

"The angle of break is the acute angle created by the coal seam bedding plane and caving line formed by roof strata movement after extraction of a longwall panel. It has a significant influence on stress redistribution both in the gob and abutment. Throughout numerical simulation investigations up to now, little attention has been paid to it, or an angle of break of 90° was used, which, however, is not realistic. This paper presents a detailed numerical modelling incorporating the angle of break against Zhenchengdi Coal Mine. The angle of break was obtained through cross-measure boreholes. Hoek-Brown constitutive model was used to simulate the rock masses. Double-yield constitutive model, which was best fitted by Salamon’s model, was used to simulate the gob. The results show that a “/ \ shape” shear failure zone develops around the gob. The shear failure in the floor along the panel edge is due to opposite shear of rock mass on two sides of the caving line, and the number of yielded zones within the gob floor close to the gob edge is smaller. According to the research, the entry was determined to be driven under the gob edge employing split-level longwall panel layout (SLPL). The other numerical simulation for SLPL shows that stress around the god-side entry is much smaller than pre-mining stress, and the area of intact rock mass at the elevating section is larger than conventional layout. Numerical modelling was then validated by field observation.INTRODUCTIONTo solve low recovery and ground control problems in longwall mining with top coal caving (LTCC) due to large gate pillar or chain pillar, gob-side entry approach is becoming increasingly popular (Nazimko, 1994; Li et al., 2016; Zhao, Wang, and Su, 2017). Gob-side entry is actually a combination of the gateroad, pillar, and gob, which is a typical panel layout with slender pillar or artificial pillar or wall. The abutment load has a profound impact on stability of the gate pillar, as well as the gob-side entry. Better estimates of abutment loading profiles will result in improved evaluations of design of pillar and gob-side entry (Larson and Lavoie, 2016)."

Jan 1, 2018

By N. I. Aziz

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack orientation.

Jan 1, 1992

By Axel Preusse

For the last 150 years, subsidence damage to the surface has been an unavoidable phenomenon associated with underground coal mining. In particular, the mechanization of mining methods in multiple seam mining and the concentration of mining activities in densely populated European metropolitan areas (e.g., Ruhr, Upper Silesian industrial region) have led to mining having a very strong influence on the earth?s surface. In both these regions, surface subsidence of more than 20m has been reported up to now in comparison to the original state. Underground coal mining in these regions strongly impairs all kinds of surface use, such as urban and industrial development, infrastructure (roads, waterways, and railways) and pipelines?without restricting the functionality of those objects to a greater extent. Demanding and, in some cases, globally unique engineering solutions have been developed and implemented for this purpose. The previously mentioned mining and industrial regions are still very strongly characterized by the (increasingly declining) coal industry and will remain dependent to a large extent and for an indefinite period on artificial drainage measures because subsidence that has already occurred is irreversible. This paper will primarily discuss the prediction of subsidence that is caused by intensive multiple seam mining and its influence on surface objects (e.g., underground pipelines). However, an approach for predicting ground uplifts due to rising mine water as a consequence of mine closures will also be described.

Jan 1, 2012

By Francis Kendorski

The mining engineering design professional has limited practical and reliable tools for planning successful room-and-pillar stone mines using readily-available and collectible information. Three techniques are in common use today: the hard rock CANMET method of Hedley and Grant, the hard rock method of Stacey and Page, and the oil shale method of Hardy and Agapito. Other methods have been proposed, such as the USBM method of Obert and Duvall, the CSIR/Penn State method of Bieniawski, and the soft rock confined core method of Abel, Wilson, and Ashwin. However, the latter have practical shortcomings when applied to room-and-pillar stone mines such as developed for construction aggregate production. Ideally, the use of multiple techniques resulting in the same acceptable and reliable answer is the goal. Recently, in several underground stone mines areas of undersized pillars were examined. These undersized pillars apparently resulted from non-adherence to a mine plan. These undersized pillars now exhibit strong evidence of incipient failure such as slabbing, opening of through-going fractures, and hour-glassing. This situation allows examination of pillar designs at a ?safety factor? of essentially one. This rare opportunity allowed the examination of the suitability and adjustment of the first three design methods discussed, resulting in greater overall confidence in the methodologies.

Jan 1, 2007

By Xiangxi Wu

Longwall and continuous mining are prevalent methods employed by Chinese underground coal operations. The main ground control challenges include roof skin deformation, roof collapse, and outbursts of coal, gas, and water. Microseismic monitoring provides valuable information on rockmass behavior and fracture propagation caused by stress redistribution, active geological structures, or gas build up within the coal strata and the surrounding rockmass. Collecting and assessing seismic data has proven to be an instructive tool for engineers to better assess ground conditions and mitigate seismic hazards associated with mining. The development of intrinsically safe and explosion proof certified seismic monitoring equipment has revolutionized China?s underground coal mines. The use of this technology allows for the optimization of gas drainage at an increased rate of two at a 50% higher purity without any increase in drilling costs. Microseismic monitoring can also be used in identifying seismically active faults and shear zones. This information can be used to assess and revise mining strategies to improve safety and ground stability.

Jan 1, 2012

By C. Dinis da Cama

In order to reduce the complexity of mechanisms influencing rock- fragmentation by blasting a simulation approach is proposed, using the capabilities of micro-computer interactive graphics. Situations involving cratering and bench blasting are simulated, and both jointed and intact rocks can be subjected to explosive action, taking into consideration its breakage mechanisms. Size analysis curves relating rock distribution before and after the blasts are determined and compared with field data.

Jan 1, 1984

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ? Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions ? became the post-event conditions.Search for evidence that either denies or supports the various ? hypotheses.Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009

By Michael Kelly

Inertial navigation technology has, for the first time, allowed the position of a longwall shearer to be mapped in three dimensions. Following the success of the technology in highwall mining and successful trials on a longwall face, the Australian Coal Association Research Program (ACARP) commissioned a three year "Landmark" project that aimed to advance longwall automation to the level of "on-face observation" by the end of 2004. This project has been completed with the following successful technical outcomes: Automatic face alignment was achieved, using an inertial navigation-based sensor on the shearer, to accurately measure face geometry and feedback signals used to move OEM (Original Equipment Manufacturer) roof supports. Operational on-line measurement of creep with creep information incorporated into face alignment corrections. Inertial Navigation System (INS)-based enhanced horizon control was bench-tested. Operational broadband communications system to shearer using wireless Ethernet on a commercial-product basis. Acquisition of located coal-face features for use in thermal infrared-based horizon control. Automated Longwall Information System (LIS) developed which integrates information from multiple systems and sensors and provides high quality visualisation and control interfaces. Automatic roadway and face convergence monitoring tools successfully tested. Condition monitoring tools developed and demonstrated for improved face reliability. This paper summarises the outcomes of the project and describes the work being undertaken for the 2 year Landmark Extension project approved in April 2005. Consistent with the conference theme, the paper focuses on the ground control aspects of the project.

Jan 1, 2005

By J. D. Cole

In order to reduce the number of longwall face moves and to increase the rate of gateroad construction, super longwall panels, 1000 feet wide and 12000 to 14000 feet long, are planned for Wolf Creek Collieries No. 4 mine. The development of the longwall panels at the mine has evolved from 5-entry, to 4-entry, to 3-entry systems. A three-entry system including pillar size and entry supporting method for the super longwall panels was designed for long-term stability. The design procedures included field observation and studies, laboratory properties tests, in-situ stress measurement, and computer analysis. Three pillar design methods consisting of PILLAR, ALPS, and the Wilson Method, and one entry supporting method, ROOFBOLT, were adopted in this study. The procedures, methods, and results are discussed in detail.

Jan 1, 1990