Search Documents

By Jesse L. Craft

Field investigation of surface subsidence events associated with both active and abandoned underground coal mines in the United States has established criteria that enable the prediction and classification of mine-related subsidence. The key was establishing the role of geology in all types of subsidence and the recognition of beam subsidence in specific geologic settings. The classification is based on overburden thickness, variations in stratigraphy, topography and mine plan. Types of subsidence are Pit, Room, Sag, and Beam. Pit subsidence is associated with three geologic settings: shale overburden, seasonally wet unconsolidated overburden, and perched water table in unconsolidated overburden. Room subsidence occurs where the roof across the width of the room fails to the surface and a shallow depression develops. Sag subsidence develops where the pillars are failing in conjunction with roof failure. Overburden thickness is generally greater than 150 feet. Beam subsidence can occur in all terrains. It is associated with retreat mining and room and pillar mining where pillar crushing or pillar compression has taken place and barriers are left inplace. They occur as beam arch or one-sided beam subsidence. Beam arch failure occurs where mining has taken place on both sides of a coal barrier. One-sided beam failure is associated with retreat mining moving from a barrier towards the entry in hilly topography. This type of subsidence occurs where a hard, thick, rock unit is acting as a bridge supporting the overburden and outcrops on the hill side.

Jan 1, 1992

By B. Singh

The use of wire ropes has already been tried in a few countries for roof support In mines. But the use of scrap wire ropes, as a method of support on extensive scale has not been reported from anywhere except India. Extensive trials using freshly discarded wire ropes for roof support were undertaken both in the laboratory and field. In laboratory, model beams supported with different reinforcing techniques were tested to evaluate their comparative load bearing capacity vis-a-vis reinforcing factor. Among all the tests, the model supported with wire rope system at 60° angle in combination with two supplementary vertical bolts offered the best result 1.e. about 95% reinforcement. It also accepted post fracture loading of the beam. In statical analysis too, the best result could be obtained with the rope installed across the gallery at 60° angle. All these findings are in conformity with the field observations obtained during roof stitching practices in coal mines. Of late, roof stitching, an effective and economical method of roof support developed at CMRS, India in 1972, found wide application in over 200 coal mines. In this method, a freshly discarded wire rope is grouted across a gallery in two inclined drill holes supplemented with two middle vertical roof bolts at every 1.0 to 1.2 m interval along the gallery. It is tensioned against the roof using wooden sleepers and thus, the whole system functions like a roof truss.

Jan 1, 1990

By Stephen C. Tadolini, Minova USA Inc., Peter S. Mills, David R. Burkhard

"Fiber-reinforced spayed concrete has been used for several years in civil and tunneling operations. Research conducted to reduce cure times and increase compressive and flexural strengths resulted in the development of Tekcrete Fast®, a cementitious product capable of obtaining 41 MPa (6,000 psi) compressive strength and 8 MPa (1,200 psi) flexural strength in only 3 hours and reaching 7 day strengths of 62 MPa and 11.7 MPa (9,000 and 1,700 psi), respectively. A single bag product that uses conventional shotcrete and gunite application systems make it a natural crossover product for mining applications. The discovery of incredible adhesion properties and high resistance to chloride permeability helps ensure long-term stability and increases the ease of application. Project results from Disaster City® in Texas and the application for rehabilitating a coal mine belt entry are presented. The case study illustrates the effectiveness of the product in stabilizing a coal mine beltway and adjacent cross-cuts that were subjected to progressive sloughage due to humidity and cyclical loading. INTRODUCTION Original research produced a shotcrete formulation that extends beyond stabilization and can be used to restore the structural integrity of damaged infrastructure. The primary challenge was to develop a shotcrete or gunite that had structural strength within a few minutes to prevent parasitic loading, allowing ingress into damaged structures minutes after applying the mix formulation. This also applies to mining conditions where rapid support of progressive failures can minimize failure. An additional benefit was discovering that the product had extremely high adhesion properties in addition to high flexural strengths. The approach to product design was the development of “single bag” dry mixes that are entirely self-contained, can be rapidly transported anywhere in the field or underground, and can be deployed using simple equipment. Dry mix eliminates issues relevant to high shear water mixing because water is added in the form of a mist at the point of delivery; thus a low water-to-cement ratio can be achieved. However, since there is no onsite powder mixing, the product must have a high degree of inherent homogeneity. Minova offers a commercial version of this material, Tekcrete Fast®, a product that has been successfully deployed in the mining industry and is currently being used in civil, construction, and tunneling operations. The material can rapidly stabilize lose ground in metal, nonmetal, and coal mines. This paper described the technology development, product testing results, and applications and describes a case study to stabilize a coal mine beltway."

Jan 1, 2017

By Michael J. Castner

"INTRODUCTIONMultiple-seam mining is an ever growing concern for engineers and mine management in every portion of the mining industry and is especially true for coal mining operations. The goal of this report is to identify the location and severity of multiple-seam interactions, provide AMSS calculations performed on the worst of these locations, and follow up with a visual examination of the underground physical effects on the roof and ribs in the locations identified for analysis. Multiple-seam mining is increasingly being studied because:1. Multiple-seam mining can create a multitude of problems such as roof falls, pillar crushing, pillar failing, rib spalling, floor heave, and inundation of water, gas, or oxygen-deficient air that can disrupt mining operations and threaten the safety of the miners.2. Multiple-seam mining is becoming more prevalent due to the depletion of virgin coal reserves.Currently, coal mining in the United States has progressed to the point that a growing number of mining companies are operating in coal seams located above, below, and/or adjacent to previously mined out coal seams. As a result, the state and federal governments are enacting higher safety standards on mining operations. For example, in years past, pillars may have been properly designed to handle single seam interactions for a particular mine or mines; however, today, where mining is now being considered above or below a previously mined area, these loading conditions may not be adequate to handle the removal of additional seams above or below the previously mined reserve. Studies from 1981 estimated that two-thirds of the mineable coal reserves in the United States would be impacted by multiple-seam implications. Today, over three decades later, it is obvious that most of the remaining mineable coal reserve will be influenced by previously extracted seams. Thus, thefocus on multiple-seam mining interactions on current and future mining operations. In 2012, underground mining in the United States produced 342,287 thousand short tons of coal. Northern Appalachia accounted for over 30% (103,301 thousand short tons) of this total (U.S. Energy Information Administration, 2013). Rosebud Mining Company and Western Allegheny Energy (RMC and WAE) have a combined total of 23 actively producing underground mining operations and at least four new mines under or ready for development. All of these mines are located in coal seams (Upper and Lower Freeport; Upper, Middle, and Lower Kittanning) of northern Appalachia (Pennsylvania and Ohio). Currently, more than half of the RMC and WAE mines are dealing with multiple-seam interactions. Seven mines are undermining previously mined out coal seams, and five mines are overmining previously mined out coal seams. Also, between these companies, five mines have inner-seam sloping possibilities (2 completed, 3 planned), most of which will result in mining over or under previously mined areas."

Jan 1, 2015

By Sean C. Farrell

In underground mining and tunneling, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Australian companies WDS Limited and Cram Fluid Power, the engineering department of J.H. Fletcher & Company was tasked to design and manufacture roof bolting modules to be mounted off both sides of a roadheader, providing in-cycle bolting. The objective was to produce a boom and bolt module that would allow an operator to bolt from a remote location, eliminating the need for miner to work in unsupported ground. The bolt module needed to operate in front of the cutting boom, but retract to a parked position out of the way during the cutting cycle. Due to Australian electrical approval requirements, it was desirable to design the module with minimal use of electrical controls. The need for multiple, complex, drill steel and bolt handling steps led to the need for a custom hydraulics package to automate several of the movements. The result of the design is dual drill and bolt modules mounted to a multistage boom with over 24 feet (7.31 m) of extension. Each unit rotates and tilts to meet the bolt pattern requirements in conjunction with the stow and load requirements. The bolt module builds on previous designs incorporating a modular assembly with each sub-component designed to be replaceable and adjustable independently from other machine components. Each major component is painted a different color to help the operator make the connection visually from the module to the operator?s control valves. Hydraulic package valves were designed to automatically control several of the sub-components during the drill cycle, reducing the number of steps a drill operator would, otherwise, have to do manually. This design removes the operator from working in unsupported roof and away from other inherent hazards, putting them at a safe distance on the operator?s platform. The cutting and bolting equipment has been combined into one machine, which is advantageous in single entry drifts because there is no need to place change equipment. The hydraulic package valves eliminate the need for any electronics, thus avoiding any electrical regulations with respect to the controls. The addition of these modules to the roadheading machine increases miner safety and streamlines production while meeting the ground control support requirements.

Jan 1, 2014

By Ken W. Mills

The ground movements associated with underground coal mining and, in particular, longwall mining, are recognised to include horizontal subsidence movements, but the mechanics of the processes that cause these horizontal movements are not well understood. Over the last two decades, three-dimensional subsidence monitoring has become routine in Australia and has provided a wealth of measurements of horizontal movements caused by mining subsidence. These measurements and other sub-surface observations allow the processes that cause mining-induced horizontal movements to be inferred and, subsequently, verified. In this paper, the mechanics of the processes that cause horizontal movements, particularly those in sloping topography, are described and discussed on the basis of field observations. There are several processes recognised to generate horizontal subsidence movements. In flat terrain, systematic horizontal movements cause the surface to move initially toward the newly created goaf and, subsequently, in the direction of mining. Tectonic energy stored as horizontal stress is released by mining, and, when the horizontal stresses are high, the magnitude of this horizontal stress relief movement is large enough to be perceptible for some kilometres from the panel. In sloping terrain, there is an additional component of horizontal movement that occurs in a down slope direction. This movement, sometimes referred to as valley closure movement, has a magnitude that is typically much greater than systematic or stress relief movements.

Jan 1, 2014

By Monte R. Hieb

Study of moisture-induced swelling strain in Pennsylvanian Period rocks of the Appalachian Plateau in West Virginia shows a 2:1 biaxial horizontal anisotropy which trends NW-SE. Oriented in-situ slabs of coal mine roof rock were collected across West Virginia, dry-sawed to size, air-dried to stability, and then monitored for moisture changes and deformations in the horizontal plane through one wetting cycle and drying cycle. Biaxial swelling strains were exhibited in nearly all rocks tested, with maximum horizontal deformations occurring normally-incident to the strike of regional geologic fold structures. This relationship persists as fold strike varies across the study area. A connection with Alleghanian fold development and/or post-Alleghanian fold relaxation is suggested. Deformations were largest in shales, but occurred in sandstones and siltstones as well. During testing, moisture-induced fractures (MIF) developed parallel to the regional fold structure and ranged in size from hairline cracks to sample-destroying cracks that were orthogonal to the observed biaxial swelling strain direction. Preferential wetting and swelling of clay minerals along NE-trending fractures, related to a fold-parallel fracture fabric of regional extent across West Virginia, is the most likely reason for the observed systematic NW-oriented biaxial swelling strains. The testing methods used in this study are simple and inexpensive and produce robust results that offer insight into a regional, anisotropic mechanical weakness that imparts a dynamic, asymmetrical horizontal stress to moisture-sensitive coal mine roof rocks over time. Because a similar mechanical fabric has been reported in Devonian-age shales, these findings may have implications for shale gas developers in the Appalachian Basin challenged by rapid aperture closure rates along horizontallydrilled induced fracture networks in Devonian rocks like the Marcellus Shale. The paper concludes with an example of how the concept of a preferred swelling strain direction might be applied to improve the effectiveness of roof trusses.

Jan 1, 2013

By Gamal Rashed

This research is divided into two parts: the first part of this research focuses on understanding coal mine bump mechanisms, and the second part focuses on mitigating the violent failure associated with a bump. Many researchers believe that the coal bumps happen because of sudden loss of constraint between pillar/ roof and pillar/floor or the hammering effect due to the breaking of thick, massive strata above the coal seam, creating a sudden impact load on the pillars and causing them to bump. However, very little work has been done to explore and understand the consequences of these proposed mechanisms for coal bumps. In the first part of this research, computer simulation of coal specimen behavior have been used to explore two issues: 1) How would an instantaneous loss of constraint or a small sudden impact load cause violent failure? 2) How does the strength of the coal specimen control coal mine bumps? Eliminating or reducing the violent failure is the main objective of the second part of this research. The coal specimen needs to be softened either in the rib zone or the core zone and then its mode of failure studied to see whether it is violent or not. Instantaneous loss of constraint and the hammering effect are associated with sudden release of elastic energy, increase in the kinetic energy, and very rapid transient vertical stresses of the coal specimen. These are three of the major proposed mechanisms for bumps. The potential for violent failure increases with increasing the unconfined compressive strength, UCS, of the coal specimen. Failure of the rib zone is not the main factor for the violent failure of a coal specimen. The energy stored in the core zone is the key factor for the violent failure.

Jan 1, 2013

By Chris Kelly

The Monroe County Quarry is an open pit granite quarry located near the town of Bolingbroke. Monroe County. Georgia. The quarry has been in continuous operation for approximately 10 years. The quarry covers approximately 27 acres and has an annual production rate of 1.0 million tons. On the morning of April 26. 2000 a sudden rapid highwall failure occurred at the west end of the north wall of the quarry pit. The failure occurred approximately one hour after a three inch-wide crack was observed in an access road located at the crest of the highwall. No indications of failure had been observed prior to the development of the crack. The active mining area had been at the base of the failed area. The pit was successfully evacuated prior to the failure and there were no losses of either personnel or equipment. The amount of failed material was estimated to be in excess of two million tons. In order to ensure a safe working environment at the quarry a slope monitoring program was established in the area of the failure. The program consisted of using an EDM survey instrument to periodically measure the location of survey prisms installed at carious points on the north wall. The locations of the prisms were recorded over several months and changes in location were analyzed in order to identify and characterize the movement of the failed mass. The results of the analysis provided a basis for recommendations regarding access to various areas of the quarry. This paper discusses the factors contributing to the failure, the method of post-failure slope monitoring, anti the interpretation of the monitoring data.

Jan 1, 2002

By Li-min Liu

The Semi-Analytical method can be used to solve a variety of problems in geomechanics and civil engineering. When it comes to layered rock strata and rock masses, it is superior to all other analytical methods. This paper presents the application of a 3-D semi- analytical method to 3-D surface subsidence and stress analysis caused by mining. In this semi-analytical method the layered elements and triangular elements ate used alternatively. Their displacement pattern, strain mahix, elastic matrix, stiffiness matrix, load matrix and stress matrix are presented. A numerical simulation program based on the semi-analytical method bas been developed using Fortran 90. This program is suitable for subsidence prediction and stress analysis of mom and pillar mining, strip longwall and mechanized longwall mining methods. It is applicable to all geological conditions and mining methods. Comparing with the finite method, this method reduces significantly the number of simultaneous equations to be solved and the amount of data preparation. It not only reduces the computer memory, but also runs faster and cost less. Key Words Semi-analytical method, surface subsidence, stress analysis, layered element, triangular prism element

Jan 1, 2002

By Ismet Canbulat, John Naylor, Jason Emery, Peter Craig, Andy Sykes

"Longwall mining is by far the most common method of underground coal extraction in Australia. The industry trends and expectations are placing increasing emphasis on the reliability and productivity of these operations. The longwalls are becoming wider and longer while retreat rates are continuously increasing due to significant improvements achieved in longwall equipment reliability and automation. This increased longwall productivity is placing significant emphasis on the reliability of longwall panel development.Although there have been significant improvements in the reliability of continuous miners and hydraulic drill rigs, the traditional resin encapsulated bolt installation is still the principal method used in all major coal-producing countries around the world. Anglo American realised an opportunity existed to introduce an alternative roof bolt installation technique called “spin to stall” in Australia. Spin to stall was first introduced in Anglo American Coal in South Africa where it has been successfully used for over a decade, though implementation of South African spin to stall resin in Australia has proven to be near impossible due to a significant difference in geotechnical conditions, mining method, and, subsequently, roof bolting equipment. Therefore, a new spin to stall development project was initiated between Anglo American Coal and Jennmar Australia (SPIN2STALL®). This paper summarises the journey of this project, the results, and the successful implementation of spin to stall achieved at Grasstree Mine.INTRODUCTIONThe Anglo American Coal business unit operates Grasstree and Moranbah North underground longwall mines in the Bowen Basin of Central Queensland, with a third longwall mine, Grosvenor, currently being developed, and two more (Aquila and Moranbah South) in the project pipeline. The vision for Anglo American is to achieve “Zero Harm” through the effective management of safety at all operations, while for the coal business unit, at the same time to achieve industry-leading operational performance. Currently, both Grasstree and Moranbah North longwalls are operating at industry best practice rates. This is placing increased pressure on the development process to allow such high productivity levels to be sustainable."

Jan 1, 2015

By Peter Cain

The Phalen Colliery in the Sydney Coalfield is extracting the 2.6 m thick Phalen Seam by the panel and pillar longwall retreat method. Abandoned workings occur in the Harbour Seam 140 m above and overlie the Phalen Colliery. Parts of these workings are flooded, and pose a number of questions relating to the safety of operations in the Phalen Colliery. In order to answer some of these questions, the Cape Breton Development Corporation re-entered an abandoned non-flooded roadway in the Harbour Seam directly above a retreat panel in the Phalen Seam to allow the deployment of instrumentation to monitor interaction effects. Fifteen monitoring sites, each 4.5 m apart, were installed in the 5 East Top Level after it had been re-entered and made safe. Each monitoring station included a vibrating wire strain gauge piezometer and a potentiometric extensometer. The piezometers were attached to rock bolts anchored into the floor and were connected by a flexible standpipe to a constant head apparatus. Variations in hydraulic head due to subsidence were monitored to determine subsidence. The extensometer units were mounted on rock bolts anchored into the floor of the roadway beneath the ribside and monitored ground strains. The instrumentation was capable of remote reading in the event that access to the site was restricted after installation. This paper describes the instrumentation, the installation programme, and some preliminary results.

Jan 1, 1993

By Kot F. Unrug

Since the introduction of longwall systems, the prediction of roof behavior and support requirements have become the major issue referring directly to safety as well as productivity. In more recent times, and especially in the USA where longwalls are exclusively equipped with costly hydraulic self- propelled support systems, a decision whether a longwall is applicable in a given condition, and when so, what kind of equipment should be selected, is of primary importance. There are numerous examples where lack of experience, and subsequently wrong selection of supports or winning machines, resulted in considerable losses. It should be emphasized that careful studies of prevailing geological and mining conditions, especially in a new area, are required to assure a successful operation. An evaluation of the conditions can be carried out in different ways utilizing such methods as: - Theoretical approach. applicable when geological conditions comply with the theoretical assumptions. - Empirical relationship which gives satisfactory results where the coefficients could be adequately determined. - Structural geological studies which must be undertaken in all cases, since the frequency of fractures and their orientation have a prevailing influence on roof behavior. - Scale model study on equivalent material for determination of failure conditions in the roof and mechanism of movement (flow) of broken rock matter. Coefficients for empirical formulas can be determined by these types of studies, as can boundary limits for mathematical modeling. - Mathematical modeling, e.g., finite element analysis. - Measurements and observations taken underground during the development period end utilization of experience for previous longwall panels in the area. Usually it is the most practical method where mining and geological conditions are comparable. An application of me or more of the above approaches remains to be a matter of judgement for particular conditions, however, the utilization of a practical experience, when available, is usually the safest way for planning a successful longwall operation.

Jan 1, 1982

By Joel Bradley, Kot Unrug, Kyle Perry, Mark Klimek

"A West Kentucky mine operation in No. 11 seam, encountered floor heave, due to the localized increase of the thickness in the fireclay mine floor. Floor heave has overridden seals installed in two mined out panels. The third seal’s location was planned for isolating that area from the Mains. A plan of support has been developed to prevent repetition of the floor heave and related problems outby the seals. The applied ground control measures were successful. An attempt of a 3D numerical modeling was made, that it would match the observed behavior of the mine floor and could be used as a design tool in similar conditions. In the paper described are sequence of events, a mitigation ground control system applied, and the first stage of numerical modeling.IntroductionWest Kentucky coal mine operation in the No. 11 seam has approached an area where the fireclay floor thickness increases to about 5 ft. Delayed floor heave has been observed. In the first sealed area (Panel KK), floor heave has overridden the seals and has begun to progress outby. This could not be allowed at the new seal location PP described in this paper because such override would affect the mains. Previously numbers of standing support systems were used, but their effectiveness was not satisfactory as is illustrated in Figure 1, Figure 2, and Figure 3. Therefore, with sealing of the next area approaching, mine management was looking for a better solution that would eliminate the problem. In that stage, our team looked closely at the geology and strength of roof and floor, as well as the characteristics of ground failure around the seal at the first site. The technical literature has been searched as well Haramy et al. 1986 Hsiung and Peng 1987, Peng 2008, Santos & Bieniawski 1987. This led to the identification of factors responsible for the ground failure. It has been determined that increased fireclay thickness from typically less than 2 ft to about 5 ft, when compared to the previously mined parts of reserve, and the strong limestone strata just above the immediate roof composed of 2 ft of black shale, created conditions of failure. It appeared that, when pillars were punching into the mine floor, the strong roof did not break but was bending, exerting high pressure on outby pillars, causing rib failures and closure. This is a similar mechanism to a strong roof affecting longwall shields. The remedial action planned was additional support."

Jan 1, 2015

By Gautam Benerjee, Veera Reddy Boothukuri, Bhattacharjee Ram Madhav, Panigrahi Durga Charan

"India’s tryst with mechanized longwall coal mining started with the introduction of the first self-advancing powered support longwall (PSLW) face at Moonidih Colliery of Jharia Coalfield in 1978 and at Godavarikhani (GDK)7 Incline of Singareni Collieries Company Limited (SCCL) in 1983. During the last 37 years, about 30 longwall units in Coal India, Ltd., (CIL) and 10 longwall units in SCCL have been introduced with powered roof supports of varying capacity, ranging from 280 to 800 tonnes, in many mines in India under varying geological and geotechnical conditions. The majority of the longwall faces in India have been worked under relatively shallow cover (up to 200m), and significant strata control problems have been encountered due to poor caveability of the roof, inadequate capacity of the supports, a lack of knowledge on longwall caving mechanisms, less than adequate strata monitoring systems, and the non-availability of quality spare parts, etc. This has resulted in structural damage to supports and increased downtime of the equipment, thereby making longwall mining in India a case of technology failure. Energy demand for a developing country like India with a population of 1.2 billion is huge, and the thrust on increasing coal production continues. However, the share of coal production from underground mines in India continues to decline (current share is around 6%) because of absence of successful mass production technology in underground coal mining. Under this backdrop, a high-capacity longwall with state-of-the-art technology was introduced in 2014 at Adriyala Longwall Project (ALP) of SCCL for the first time in Indian Coal Mining Industry. The first longwall panel (LWP) has been completed successfully. This paper highlights the major geotechnical challenges encountered during development of the longwall gate roads due to the presence of two overlying clay bands, significant in-situ horizontal stresses and the experience of using rigid (welded) steel wire mesh with resin-anchored roof bolts. Efforts have been made to analyze longwall weighting and caving behavior, such as main and periodic weightings, the effect of front and side abutment pressures, and the behavior of gate roadway support systems under immediate friable weak roof with overlying massive sandstone."

Jan 1, 2017

By Kun Li, Shuaishua Yue, Huigui Li, Yuan Ruifu, Yongxiang Xu, Huamin Li

"Coal seams in Tashan Mine of Datong Coal Group in China average 49.2 ft (15m) thick and have been mined by the top coal caving longwall mining method of large mining height. Mining height was 12.5 ft (3.8m) and the top coal caving height was 36.7 ft (11.2m). The gateroad pillar between panels was 124.6 ft (38m). During retreat mining, serious bumps occurred in the gateroads on both sides of the pillar affecting safety production. Therefore, pillarless mining was experimented.Using numerical modeling and comparative study of cases of similar mining condition, it was decided to employ a 19.7 ft (6m) wide pillar, rather than the previous 124.6 ft (38m) wide pillar. Support system for the gateroads was designed and implemented. During gateroad development, pillar failure conditions and entry deformation were monitored. Hydraulic fracturing method was employed to cut off the K3 sandstone along the entry rib so as to reduce the abutment pressure induced during retreat mining. Support reinforcement method combining grouting and advanced reinforcement methods was proposed to insure stable gateroad ahead of mining. Methane drainage and nitrogen injection were implemented to eliminate hazards associated with mine fire and spontaneous combustion.Since the development of gateroad has just completed, and retreat mining has not begun, the effectiveness of the proposed methods is unknown at this point. However, monitoring will continue until after mining. The results will be published in a separate paper.INTRODUCTIONGeneral descriptionTashan mine is located about 15 Km south of the city of Datong, Shanxi province, China (aure 1). The 2014 raw coal production was 25 million mt."

Jan 1, 2015

By WenFeng Li

A 3D roof bolt model with the consideration of rebar, resin, bearing plate, and resin/rock interface was developed for studying the bolt/rock interactions of the tensioned and fully-grouted resin bolts. For the tensioned bolts, 2 ft compressive zone above the rooflineis generated by the 10 tons pretension. Since the free portion of the tensioned bolts displays a higher vertical stress, the increase of the bearing capacity of the rocks in such range is much larger. For the fully grouted resin bolts, despite no pretension is generated during installation, the roof sag can indirectly generate a compressive zone near the roof line. In addition, the analysis on the differences in bolt/rock interactions when employing the tensioned or fully-grouted resin bolts indicates that the fully-grouted resin bolts are preferred as the primary support when weak and thinly-bedded immediate-roof is present. Meanwhile, it is found that both the tensioned and fully-grouted resin bolts may have very limited effect in preventing and/or control the cutter roof.

Jan 1, 2014

By Joe Wickline, Mark A. Van Dyke, Wen H. Su

"Geological factors and mine design contribute to mining-induced seismic activity, and this is especially true in longwall mining. Massive rock units are a key cause of seismic activity due to catastrophic failures that release large amounts of energy. Other factors, such as overburden depth, panel design, pillar design, rock strength, and proximity of the massive rock unit to the coal seam, all have a role in the potential and size of a seismic event. A recent seismic event was recorded by a deep longwall mine in Virginia at 3.7ML on the local magnitude scale and 3.4 MMS by the United States Geological Survey (USGS) in July 2016, which had no impact on the mining operations. Further investigations by NIOSH and Coronado Coal researchers have shown that this event was associated with geological features that have also been associated with other, similar seismic events in Virginia. Detailed mapping and geological exploration in the mining area has made it possible to forecast possible locations for future seismic activity. In order to use the geology as a forecaster of mining-induced seismic events and the energy potential, two primary components are needed. The first component is a long history of recorded seismic events with accurately plotted locations. The second component is a high density of geologic data within the mining area. In this case, 181 events of 1.0ML or greater were recorded by the mine’s seismic network between January, 2009, and October, 2016. Within the mining area, 897 geophysical logs were analyzed from gas wells, 224 core holes were drilled and logged, and 1,031 fiberscope holes were examined by mine geologists. From this information, it was found that overburden thickness, sandstone thickness, and sandstone quality contributed greatly to seismic locations. After analyzing the data, a pattern became apparent indicating that the majority of seismic events occurred under specific conditions. Three maps were created using MineScape geological mapping software. MineScape deploys an interpolator known as FEM (finite element method) and is based on a series of gridded triangles to forecast the probability and magnitude of an event if a particular panel were to be mined. The forecast maps have shown accuracy of within 74%–89% when compared to the recorded 181 events that were 1.0 ML or greater when considering three major geological criteria of overburden thickness of 1900 feet or greater, 20 to 40 feet of sandstone within 50 feet of the Pocahontas number 3 seam, and a longwall caving height of 15 feet or less."

Jan 1, 2017

By Katya V. Babenko, Victor V. Nazimko

We address the problem of the stochastic nature of ground pressure manifestation. Stress distribution in a rock mass and ground irreversible movement are governed with a set of random factors that affect the over-peak strength of the rocks, making them extremely sensitive to any perturbation of the external environment and to internal fluctuations of the thermodynamic state of the rock. We investigate the fluctuation evolution during a longwall face movement to find out whether the fluctuation dissipates or builds up. Five adjacent powered support failures simulate the ground pressure fluctuation. The main roof has been presented as a plate that reposed on the rigid base. The stiffness of the base depends on the thickness of the extracted coal seam and on the dilation of the caving roof. Maximum stiffness occurs in situ, and minimum stiffness is in the gob when the roof is highly flexible and subsides elastically, without caving. The more stress acts in the roof, the higher the cavity that occurs and the larger increment of the base stiffness. The wave of the fluctuation has extended both to the direction of the longwall advance and along the face from the point of the fluctuation agitation. There was an incubation period when the fluctuation was negligible, and the process of the main roof caving remained unaffected. The distance of the longwall advance during the incubation period was twice the longwall length when the fluctuation magnitude was 1% relative to the maximum possible disturbance and 0.76 of the longwall length for the magnitude of 24%. However, the pattern of the roof caving has dramatically changed during further movement of the longwall. All caving parameters have changed: step of the caving, ground pressure distribution, and the manifestation in the longwall and entries. A histogram of the fluctuation magnitude is symmetric in accordance with normal distribution. However, the distribution has abnormal excess. These findings are the first step toward answering the question whether it is possible to forecast the process of main roof caving and weighting consistently. Our preliminary conclusion is that the space and time intervals where this prediction can be made with certain reliability are limited, so further investigation is needed.

Jan 1, 2017

By David R. Burkhard

"Comparative roof beam performance, as measured by delamination within the bolted horizon, was used to evaluate two types of roof bolt drill hole geometries in a development setting. Short encapsulation pull tests had demonstrated a higher grip factor in drill holes featuring helical grooves in the side walls in comparison to drill holes featuring continuous smooth to slightly rough walls. The study incorporated the two geometries during development mining in which fully grouted mechanically anchored bolts were installed as primary roof support.bolts were installed as primary roof support.The study site, in an entry adjacent to a longwall panel, was instrumented with extensometers and data collected during longwall retreat. Statistical analysis was conducted to validate null and alternative hypotheses used to compare drill hole geometries. Analysis yielded no statistically significant difference between drill hole geometries. Inspection of the data does reveal less delamination within the smooth walled site in comparison to the site containing grooved hole geometry.INTRODUCTIONFrom their introduction as a means of ground control over sixty years ago, roof bolts today are the primary mechanism of roof support utilized throughout mining. Whether through suspension, keying, or beam building, roof bolts are employed to reinforce the inherent strength of the strata comprising the immediate roof with the goal of creating a competent bolted horizon of sufficient load bearing capacity to be self-supporting for a given mine's design life, stress regime, and geomechanical properties.For grouted bolts in sedimentary strata, axial loading due to vertical rock movement and bending due to horizontal rock movement are the principal means of loading (Signer, 2000). Regardless of the type of bolt and extent of grouting employed, the success of any roof bolting design is determined, to a large extent, by the effectiveness of load transfer between the rock, grout, and bolt.At San Juan Mine, an underground longwall mine located in the northwestern corner of New Mexico, a number of different roof bolt types, grades, and lengths have been used over the years in an effort to optimize primary roof support. One common denominator shared throughout has been the use of full length grout. Load transfer for full length grout is achieved primarily through mechanical bonding between the grout and rock. It is this interaction that is the focus of the study described in this paper. The study assessed and compared two types of bolt hole geometries employed during gate road development at San Juan. Underground instrumentation and evaluation of the bolted roof provided the means of assessment and comparison."

Jan 1, 2016