Search Documents

By Taghi Sherizadeh, Pinnaduwa H. S. W. Kulatilake

"This paper examines the effect of different geological and mining factors on roof stability in underground coal mines by combining the field observations, laboratory testing, and numerical modeling. Observations at an underground coal mine that uses the room-and-pillar mining method showed several failures of the immediate roof, and is used as a case study. Three-dimensional distinct element analyses were performed to study the intrinsic roof failure mechanisms and to evaluate specifically the effect of in-situ stress magnitudes and directions, discontinuity mechanical properties, and variation of pillar to room size on roof stability.INTRODUCTIONThe lithology of the immediate roof with respect to the underground openings plays an important role in stability of the roof in underground excavations. Laminated, or thinly bedded shale, is one of the most frequently seen overlaying strata above the coal deposits. The bedding planes and interfaces have very low or close to zero tensile strength in the direction perpendicular to the bedding planes, and their shear strength is much lower than of the rock layers. As a result, the bedding planes are much weaker than the rock layers. Therefore, due to the stress concentrations caused by excavations, slippage and separation can easily happen along the bedding planes before initiation of failure within the rock layers.In the past, several attempts have been made to understand the mechanism behind the roof failure in underground coal mines. Most of these earlier attempts were based on empirical techniques and continuum based numerical methods that have limited capability in simulating the response of discontinuum rock mass behavior to excavation. Different factors such as the magnitude and direction of the horizontal in-situ stresses, type and mechanical properties of roof rock, surface topography, geological anomalies, gas pressure, slippage and separation of bedding planes at the roof and floor, entry width and excavation sequences are identified as key factors that could significantly impact the stability of the roof. Among all the aforementioned factors, in spite of its importance, the impact of slip and separation of bedding planes on roof stability has not received enough attention from researchers. In a few available numerical modeling studies, the bedding planes are modeled using the continuum based numerical codes such as ABAQUS (Chen, 1999) and FLAC3D (Ray, 2009). However, since the bedding planes among the roof layers become discontinuous during the numerical analysis, this behavior is most likely not be accurately captured by the continuum based numerical models. Chen (1999) conducted finite element analysis to study the impacts of the roof and coal interface slip and the bedding planes slip in the roof on the stress distribution in the roof strata by using the finite element analysis software named ABAQUS. To avoid the complications associated with the finite sliding between two deformable bodies, he limited his study to the two-dimensional finite element analysis (plane strain). He concluded that the slip and separation of interfaces and bedding planes have significant impact on the behavior of the roof strata and without considering the interfaces, the roof bolt functions cannot be simulated properly by using the numerical analysis methods. Gadde and Peng (2005) performed three-dimensional finite difference analysis using FLAC3D software with strain softening material behavior to simulate the cutter roof in an underground coal mine. Their numerical model was fully continuum and no bedding plane was included in the model. They suggested that the strain softening material model can help to simulate the cutter roof failure up to a satisfactory level (Gadde and Peng, 2005))."

Jan 1, 2015

By Zhijie Zhu

In order to determine the overburden failure characteristics of extra-thick seam mining, EH4 electromagnetic image system and borehole televiewer survey were applied to panel 8100, Tongxin coal mine. EH4 electromagnetic imaging system was used to map the overburden strata before and after mining. Analysis of the distribution of the electrical conductivity showed that the fractured zone height was 492-558 ft (150-170m); Observation through the borehole televiewer showed that the fractured zone height of water conductivity (or water flowing fractured zone height) was 110m-142m. The results of the two methods showed that the fractured zone height of water conductivity was 492-558 ft (150- 170m) or 10-11.3 times the mining height.

Jan 1, 2014

By Bruce K. Hebblewhite

Underground pillar extraction continues to be practiced in Australia in various forms, in spite of the dominance of the longwall method, which accounts for over 90% of underground production. Australia has been a leader in various forms of pillar extraction, particularly since mechanisation was introduced to the industry during the middle of the 20th century. Historical developments have included a range of thick seam mining pillar extraction methods; the widely adopted Wongawilli method; early adoption of the use of mechanized breaker line supports; and a number of more recent partial extraction systems including what is known as rib stripping. Current pillar extraction practice varies from total extraction panels to various forms of partial extraction, driven by either surface subsidence constraints or by underground conditions. This paper reviews a number of different pillar extraction methods and mining layouts, and also highlighting a number of fundamental geotechnical principles which have been found to be critical for safe pillar extraction ? often through lessons learned the hard way, as a result of back analysis of different accident scenarios. These principles include the all-important understanding of the location of the goaf (gob) edge at any point in the operation, and the management of that goaf edge; the impact of geological structures on local and regional stability; the critical importance of extraction lifting sequences; the role of stooks (remnant pillars); and a number of other factors. The paper will also briefly reference the educational and training practices adopted in Australia aimed at the continuous improvement of pillar extraction safety.

Jan 1, 2011

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a chain pillar design methodology readily usable by colliery staff. The project was primarily funded by the Australian Coal Association Research Program and further supported by several Australian longwall operations. The starting point or basis of the project was the Analysis of Longwall Pillar Stability (ALPS) methodology. ALPS was chosen because of its operational focus; it uses tailgate performance as the determining chain pillar design criterion rather than simply pillar stability. Furthermore, ALPS recognizes that several geotechnical and design factors, including (but not limited to) chain pillar stability, affect that performance. There are some geotechnical and mine layout differences between United States and Australian coalfields that required investigation and, therefore, calibration before the full benefits offered by the ALPS methodology could be realized in Australia. Ultimately, case history data were collected from 19 longwall mines representing approximately 60% of all Australian longwall operations. In addition, six monitoring sites incorporated an array of hydraulic stress cells to measure the change in vertical stress throughout the various phases of the longwall extraction cycle. The sites also incorporated extensometers to monitor roof and rib performance in response to the retreating longwall face. The study found strong relationships between the tailgate stability factor, the Coal Mine Roof Rating, and the installed level of primary support. The final outcome of the project is a chain pillar design methodology called Analysis of Longwall Tailgate Serviceability (ALTS). Guidelines for using ALTS are provided.

Jan 1, 1999

By Christopher Mark

Coal bursts are typically associated with highly stressed coal. Most bursts occur during retreat mining (longwall mining or pillar recovery) in highly stressed locations like the tailgate corner of the longwall panel. Others are associated with multiple seam interactions. However, a small but significant percentage of coal bursts have occurred during development or in outby locations unaffected by active mining. Most development bursts have been relatively small, but some have been highly destructive. No theory of coal bursts can be complete if it does not account for this type of event. This paper focusses on the development mining coal burst experience in the US, putting it into the context of the entire US coal burst database. The first documented development coal burst occurred almost exactly 100 years ago during slope drivage at the Sunnyside Mine in Utah. Sunnyside subsequently had a long history of bursts, mainly during retreat mining but also during development. Several Colorado mines have also experienced multiple development bursts. Some, but by no means all, of the development bursts in these western US coalfields have been associated with faults. In the Central Appalachian coalfields, most development bursts have occurred in multiple seam situations. In some of these cases, however, there was no retreat mining in either seam. The paper closes with some lessons from this history, with implications for preventing such events in the future.

Jan 1, 2017

By William Kendall

"A tremendous amount of research, analysis, and engineering time is used to design a proper roof support system including the type, length, and location of the roof bolts. Unfortunately, since the roof bolts are being installed under unsupported roof, the exact location for the bolt holes cannot easily be determined and then marked onto the roof. The actual location where the roof bolts are installed is typically left to visual estimates by the operator. This frequently results in either (1) the operator overestimating the space between roof bolts and installing more bolts than required, thereby increasing cost and reducing efficiency; or (2) the operator underestimating the space between roof bolts and installing fewer bolts than required, thereby reducing safety, leading to potential roof failure or possible violations.A patented laser light grid system has been developed by J .H. Fletcher and Monitech, a South African Company, to aid in proper machine positioning in the heading and proper bolt spacing. The system can also show when an entry is over width, requiring additional roof support. The system is relatively simple and inexpensive. The concept is applicable across the full range of roof bolters from low to high seams and from single boom to multiple boom bolters. The system can be configured to meet most bolting patterns.The system consists of several very small 1 milliwatt, class 2, line type lasers that project a line onto the roof. The actual laser is 27mm in diameter x 47mm long (1"" x 1.8""). In South Africa it is approved as intrinsically safe and is mounted inside a 50mm diameter x 64mm long (2""x 2.5"") protective housing. In the USA, we are seeking an X/P approval and the laser will be mounted in a headlight enclosure 110mm diameter x 125mm long (4.3"" x 5""). Fifteen of the systems have been installed in South African coal mines with good results.The system has aided the mines in meeting the bolt spacing tolerance used in the Republic of South Africa, which is typically 15% of the nominal bolt spacing or 7 in for 4-ft bolt spacing. Fletcher has submitted the system to MSHA for approval in the US."

Jan 1, 2016

By Nikzad Oraee, Parham Khajehpour, Kazam Oraee, Arash Goodarzi

"Rock fall related accidents continue to occur in coal mines, although artificial support mechanisms have been used extensively [1]. Roof stability is primarily determined in many underground mines by a limited number of methods that often resort to subjective criteria. It is argued in this paper that stability conditions of mine roof strata, as a key factor in coal mines, must be determined by a survey which proactively investigates fundamental aspects.Failure of rock around the opening happens as a result of both high rock stress conditions and the presence of structural discontinuities. The properties of such discontinuities affect the engineering behavior of rock masses causing wedges or blocks to fall from the roof or slide out of the walls [2]. A practical rule based approach to assess the risk of a roof fall is proposed in the paper. The method is based on the analysis of structural data and the geometry and stability of wedges in underground coal mines. In this regard, an accident causing a huge collapse in a coal mine leading to four fatalities is illustrated by way of a case study. A comprehensive investigation of the hanging wall has been gathered through a systematic collection of evidence. The investigation results are then analyzed, and an interpretation of the evidence gathered is provided.For this purpose, horizontal and vertical profiles are prepared by geophysical methods to define the falling zone and its boundaries. The collapse is then modeled by the use of sophisticated computer programs in order to identify the causes of the accident and hence recommend corrective actions to prevent or minimize reoccurrence probability of similar accidents. The corrective measures are placed into a rule-based framework for the benefit of the mine operators.INTRODUCTIONRoof rock failure has generally been the most dangerous hazard for underground coal mining in the world. Failure of rock around shallow coal mine openings often results from loosening of blocks of rock on the weakened planes under the influence of gravity. This condition is not typically seen in large deep coal mines. There are a number of differences between large mechanized mines and small mines related to ground control [3]."

Jan 1, 2015

By Houquan Zhang, Yu Wu, Yanlong Chen, Zhenfu Luo, Aihong Lu

"A non-destructive detection scheme for bolt installation quality was designed by adopting the method of non-destructive detection on bolt installation quality. Based on the field measurements, a random non-destructive detection method for determining the characteristic length including anchoring length, free segment length and initial axial load of bolt was discussed, and the characteristics of increasing bolt axial load in the initial stable stage was obtained. The results show that the bolt axial load and deformation of surrounding rocks correlate each other. Compared with the traditional detection technique for bolt installation quality, the non-destructive detection method has obvious advantages such as random, accuracy, and economic. The method provides a reliable basis for bolt support optimization and stability control of surrounding rocks.INTRODUCTIONBolt support in roadway can make the surrounding rocks and bolt form a structure in the early stage of roadway development through the bolt pre-tension, which can maximize the self-bearing capacity of surrounding rocks. Thus it is a form of active support (Kang, 2007). In order to make the bolt play an active supporting role, it needs to ensure the installation quality of bolting. Thus the bolts can supply a high initial anchoring force and control the deformation of surrounding rocks (Shan, 2009; Wei, 2012). Moreover, bolt supporting is a concealed work. Once installation quality problems appear; it will be difficult for effective detection and screening (Xie, 2008).THE PROBLEMS OF BOLT INSTALLATION QUALITY IN COAL MINE AND ITS DETECTIONThe Problems of the In Situ Bolt InstallationDue to the problems in installation environment, machine, and technique, and workers proficiency (Li, 2003), there are many problems exist in bolt installation. If the borehole depth is too long, the anchoring agent will accumulate at the bottom of the bore, which reduces the anchoring length. Furthermore, if the borehole depth is short due to the poor geological condition, the exposed part of the bolt will be too Jong and the pallet cannot cling to the rock face, which prevent the pre-tension from being applied. The pre-tension is very important for bolt installation. If pre-tension is insufficient the rock bolt cannot control the deformation of surrounding rock efficiently and the bolt anchoring force will decrease considerably. The bolt length is another important parameter for anchoring quality, which will affect the control area of bolt supporting. In addition, the cleanness of drill hole has a great influence on the effective anchorage length of bolt. If the drill hole cleaning is not enough, it will directly affect the anchoring agent and the contact area of surrounding rocks, which will decrease the effective anchorage length and initial anchor-force."

Jan 1, 2016

By Ihsan B. Tulu, Keith A. Heasley, Aanand Nandula

"The objective of this paper is to present the development of a software tool that will assist in an area calculation of the Analysis of Roof Bolting Systems (ARBS) support intensity while incorporating more detailed geology, stress, and intersection span input. In this area ARBS tool, a detailed CMRR distribution can be determined from the available geologic database at the mine. In addition, the overburden and multiple-seam stresses, as obtained from the boundary-element program LaModel, can be converted to a “pseudo-depth” which is then used as the depth input to the area ARBS calculation. Finally, the section-specific intersection spans can be determined from the mine design for input to the calculation. All this detailed area input information for ARBS is handled by the latest version of the Stability Mapping (StabMap) program, which now outputs an area ARBS suggested support density given the required input parameters. This final ARBS grid can be plotted, analyzed and overlaid on the mine map for optimum use in support design and for presentation to production personnel.INTRODUCTIONSince the inception of roof bolts in the 1940s, there has been a lack of a universally accepted roof bolting design method (Mark, 2002; Mark and Pappas, 2012). To address this situation, the National Institute of Occupational Safety and Hazard (NIOSH) developed roof support design guidelines, which were incorporated into a computer program called the Analysis of Roof Bolting Systems (ARBS). These guidelines were based on the effects of roof quality, stress, and mine geometry (Mark, Molinda and Dolinar, 2001). The roof rock quality in ARBS is represented by the Coal Mine Roof Rating (CMRR), the depth is used as a surrogate for the stress, and the intersection span serves to represent the mine geometry (Mark, Molinda and Dolinar, 2001). These three input parameters are used in the fundamental, empirically derived equation of ARBS to calculate a required support density factor, called ARBS, (Mark, Molinda and Dolinar, 2001):"

Jan 1, 2018

By Ry Stone

"There have been many design practices utilised within the coal mining industry to arrive at the minimum densities of primary ground support required during roadway development. This paper demonstrates the practical use of empirical databases, and focuses on the main drivers for ground support as demonstrated in conceptual models.Golder Associates’ empirical databases used for ground support include a Primary Roof Support Database and a Primary Rib Support Database. Both are based on successful ground support designs installed in mines in Australia, the US, the UK, South Africa, New Zealand, and Europe. The term “successful” refers to those designs that were used on a repeated basis for the purpose of roadway development.The Primary Roof Support Database indicates that the major factors influencing successful roof support designs are roof competency, expressed as the Coal Mine Roof Rating (CMRR), and in situ stress. As roof displacement is essentially a function of horizontal stress and roof competency, in order to provide some form of measure as to the likely magnitude of roof deformation during roadway development, the depth of cover is divided by the CMRR to arrive at a “Stress Strength Ratio” (SSR). The database indicates that the higher the SSR, the greater the likelihood that the roof will require higher densities of support.In regard to the Primary Rib Support Database, it is evident from the current database that the primary factors affecting the capacity of rib support required for a successful design are roadway height and depth of cover. In order to provide some form of measure as to the likely magnitude of rib deformation during roadway development, the depth of cover is multiplied by the height of the roadway to determine a “Rib Deformation Rating” (RDR). Similar to the roof, the database indicates that the higher the RDR, the greater the likelihood that the rib will require higher densities of support.These databases have been used to help determine the minimum primary ground support designs required at many mine sites in Australasia, Europe, and the US. This paper will demonstrate the effectiveness and practicality of these databases at two selected mines in Australia and the US.In order to improve the Primary Rib Support Database, this paper will also propose a new rib deformation rating based on the addition of site specific coal strength data for the Australian mines. The proposed rating attempts to capture the main variables that define the behaviour of a buckling column."

Jan 1, 2015

By William Kendall

INTRODUCTION Stillwater Mining Company, with its two underground, hard rock mines in South Central Montana, is the largest primary producer of palladium and platinum in the Western Hemisphere. Platinum Group Metals (PGMs) are mined from a specific zone within the Stillwater Complex, a layered mafic/ultramafic igneous intrusion, named as the J-M Reef. Over much of the J-M Reef, the economically minable, mineralized horizon is contained at typical horizontal widths of 6.5 ft to 8 ft wide. This feature of narrow mining widths has made it challenging to safely and effectively mine these areas of the J-M Reef using mechanized cut and fill and sublevel sill development mining methods. Mechanization of most or all of the steps of the mining process is important to Stillwater in the continuous pursuit of high standards in safety and health. Mechanized bolting within the J-M Reef ore production headings is an important piece of reaching these objectives. In general, metal/non-metal mining requires varied mining techniques, as compared to more traditional bedded mineral/resource deposits. Narrow vein mining is a selective mining technique that generates a minimal amount of waste material while obtaining the more valuable ore deposits. Drilling and bolting in narrow vein mining has traditionally been performed with air-powered, hand-held ?jackleg? equipment because mechanized equipment is, typically, too large for the selective narrow vein techniques. In addition, traditional hand-held pneumatic equipment provides significant flexibility for small-opening, narrow-vein developments, reducing waste rock handling and improving ore recovery management. The hand-held equipment is also relatively inexpensive to purchase. Due to its simplicity, it is also relatively easy to train operators to use hand-held equipment. Hand-held equipment has been routinely used to safely install ground support and to develop production faces in hard rock mines for many years. Although it is effective, the hand-held equipment requires operator exposure to certain inherent hazardous conditions in the active face/development mine areas. These include falling rock, tripping hazards, bending/twisting/lifting hazards, high noise levels, and chemical fumes from the hammer exhaust. Based on health and safety statistics from the Stillwater mines, operation of the rotary-percussive hand-held equipment adversely affects the long-term health of the operator?continual jackleg operation frequently results in long term damage to hearing, shoulders, arm and wrist joints, and back injuries. This reduces the quality of life for the operator and also results in higher personnel turnover rates for the mining company.

Jan 1, 2014

By Anthony Spearing

There are approximately 68 million rockbolts installed annually in underground coal mines in the USA (Tadolini and Mazzoni, 2006). The most utilized is the passive fully grouted resin rebar bolt, which constitutes almost 90% of the primary support in US underground coal mines. Resin-grouted rockbolts are a very effective and safe support, but their performance still needs to be further optimized and improved. This paper investigates their performance and suggests operating conditions to optimize the performance of resin-grouted rockbolts. In addition, this paper discusses a small-scale test that can also be used to evaluate the performance of rockbolts that is quicker, easier, and less costly than short encapsulation tests.

Jan 1, 2014

By David Bigby, Tim Ross, David Conover

"Extensive arrays of telltale roof monitoring instruments were recently installed in a Mexican copper mine and a large underground mined storage facility in the eastern U.S. The data were used to evaluate roof stability during development and retreat mining and after installation of supplemental supports. Both manual-reading and automated systems were employed and consisted of up to 64 instruments. This paper will discuss the practical issues involved with installation and monitoring, including reliability and maintenance. Examples will be given for telltale response in relation to known events affecting roof stability, including nearby pillar extraction roof caving, installation of supplemental cable bolts, and separation of the immediate roof layer. The strategy for processing the large quantity of data, presenting the data for review, monitoring the system remotely, and identifying and reporting critical events will be described.INTRODUCTIONTelltales have been used for many years with many varied applications. They are relatively inexpensive, easy to install and interpret, robust, and adaptable. The term ""telltale"" generally denotes a strata extensometer that incorporates a visual indication (and warning) of strata movement. The most common dual-height telltale (Figure 1) was developed by British Coal in the early 1990s as roof bolting was replacing steel arch support (Bigby, 2001). Dual-height telltales provide immediately visible measurements, distinguish between movements above and below the bolted height, and are an established means for providing preemptive warnings of roof falls.Many improvements and modifications on the basic design have been developed to adapt to different mining conditions. For example, triple-height telltales are commonly used where roof bolts of different lengths are installed. The standard manuallyread telltales are limited by the difficulty of obtaining frequent, consistent, and accurate readings, especially in high openings. The instruments may also be located in unstable or inaccessible areas. Consequently, an intrinsically safe electronic telltale system was developed that combines high accuracy and both local and remote reading options. The system supports a network of up to 100 dualheight telltales on each of four separate branches. The instruments are connected with a two-conductor cable and can be read both underground, using a portable readout, and on a surface computer (Figure 2). The automated system still provides the visual warning indication underground."

Jan 1, 2010

By Selmar A. Oliveira

"Safe mine closure is an important step in the mining lifecycle. Plans for safe and efficient closure should begin at the inception of mining. Ideally, closure occurs when the reserve has been depleted. However, when the abandonment of a mine occurs prior to the depletion of the reserve, several problems arise which need to be treated. This situation occurred at Verdinho Mine, located in the state of Santa Catarina, southern Brazil. Verdinho Mine is a coal mine that operated for more than 40 years without had backfill technologies applied. Soon before the exhaustion of the reserves, it was abandoned by the owners without proper closure. As a result, the Federal Public Ministry filed a public civil action to promote proper closure. Several parties are currently involved, including the National Department of Mineral Production (DNPM), the mining regulator of the Brazilian Government. To meet the judicial determination, a cooperation agreement was initiated between DNPM and the Federal University of Rio Grande do Sul (UFRGS) to identify and to monitor parameters which could result hazard due flooding mine, to model the various conditions to minimize the impact of flooding caused by total abandonment. Many processes must be planned and planned early in mining operations, and these processes must be performed over the life of the mine. Financial resources must be guaranteed by a specific fund fueled by operating revenues. When these resources are not properly employed, costs and technical difficulties prevent proper closure progress. If the removal of subsoil equipment, treatment and control of groundwater, regeneration of the surface, and closure of openings are not done correctly, there can be environmental, social, and stability impacts over time. To avoid this in the future, a detailed study is being performed at the Verdinho Underground Coal Mine on how to appropriately implement mine closure and monitoring procedures. This study is being conducted in response to a lawsuit filed by the Federal Public Prosecutor’s Office. INTRODUCTION The nature of the Mining Industry is such that all mining is a temporary activity, where the operational life of a mine is defined by the final project scope. The operating life of a mine lasts from a few years to several decades. Mine closures occur once the mineral resource at a working mine is exhausted, or operations are no longer profitable. Mine closure plans are required by most regulatory agencies worldwide, such as the Mineral Production National Department (DNPM) in Brazil."

Jan 1, 2017

By David L. Kuck

This paper describes a system for providing structural, support in underground mines, employing water ice for pillars. packwalls and brattices. It consists of a refrigeration brine chiller, brine circulation system, and disposable plastic containers. The system provides for the timely freezing of uniform ice pillars, and for ice maintainance and/or melting on demand. Unique, useful ice properties include: expansion upon freezing, resilience to dynamic loads, and plasticity. Ice will not dilute or contaminate coal or ore. Economic advantages include: 1) lower labor and material costs (water can be piped to the ice pillar site through mine-water, spray-water, or drill-water lines); 2) replacement or supplementation of timber. concrete or other roof support equipment; and 3) potential use of ice brattices as ventillation control; and 4) conversion of ice bratices to ice pillars upon retreat. See Figure . A safety advantage for personnel and equipment is that ice pillars can be placed in hazardous sites, by remote control, if neccessary, without human entry. All filling, freezing and melting operations can be controlled from a safe distance.

Jan 1, 1987

By Ben Mirabile, Alan Campoli, Rodney Poland

"The majority of U.S. underground coal mines use some form of cable bolt as supplemental support to a primary roof bolting system. Many coal operators employ the high load capacity of non-tensioned cable bolts, cable roof trusses, or solid bar trusses in an attempt to suspend the primary bolted horizon to overlying strata. However, in cases where many discontinuities exist in the roof strata or where pre-existing fractures are present, these passive supplemental support systems often cannot adequately control roof deflection. This paper examines the application of tensioned cable systems to minimize roof deflection in very laminated and fractured strata. Three underground case studies are presented to demonstrate the application of tensioned cable bolts. The first case study involves the rehabilitation of a longwall head gate in the Eagle Seam with highly laminated and fractured sandstone. The second case study examines the recovery of a longwall face in the Alma Seam. The final case study addresses rehabilitation of a longwall head gate in the Pittsburgh No. 8 Seam that was developed in a sandstone channel margin area and subjected to horizontal stress concentration.INTRODUCTIONDuring the previous decade, Jennmar Corporation has recognized coal operators' increasing interest in tensioned cable bolts. The majority of these tensioned cable bolt systems have been applied in adverse roof conditions including broken ground, high horizontal stress areas, and highly laminated roof strata. In most cases, qualitative data on roof conditions after application of tensioned cable bolt support indicate successful implementation of these systems. The qualitative evidence suggests that the combination of high load' capacity and applied tension provides superior supplemental roof support in adverse roof conditions. This research aims to quantify the effects of applied tension to cable bolts. This paper will review the types and installation of tensioned cable bolt systems, present initial laboratory test data, discuss successful case studies, and propose an instrumentation system for quantification of tensioned cable bolt performance."

Jan 1, 2010

By Adam Mackenzie, Dan Payne, Yass-Marie Rutty

"Historically, the Crinum mine has experienced significant falls of ground when longwall production slowed to prepare for recovery in weak roof areas. These conditions continue through the recovery process and result in both safety concerns and delays. When mine plans and exploration revealed that most of the mine's future longwall recoveries were located in weak roof areas, a decision was made to try pre-driven recovery roads as a solution to the problem. After completing eight pre-driven recovery roads with varying degrees of success and numerous lessons, the Crinum North mine now utilizes a modified Pre-driven Recovery Roadway (PDRR) to improve the longwall take-off process in weak roof areas. During mine development, a standard roadway is driven where the final recovery location of each longwall is planned. After the installation of secondary support, the PDRR is backfilled with a cement-flyash mix to provide support to the roof, and confinement to the ribs and floor of the roadway. The method has been refined over the last four years to provide greater strata stability and improved operational and safety performance compared with conventional take-offs at Crinum, and has resulted in a site record of longwall relocation in 11.5 days (pull mesh to picks in coal). This paper describes the evolution of the PDRRs from Crinum East to Crinum North, including lessons from initial attempts and changes to the secondary support regime, the operational approach during the final stages of retreat, the backfill strategy and plans for the future.INTRODUCTIONThe Crinum mine is the underground component of BHP Billiton Mitsubishi Alliance's (BMA) Gregory Crinum mine, located northeast of Emerald, Queensland (Figure 1).The Crinum mine has a history of roof control problems coming into and during longwall recoveries. Weak roof, combined with the slow mining, which is a consequence of preparing for equipment recovery, pulling mesh (which also creates tip-to-face issues), and the lengthy bolt-up process, often results in loss of immediate roof and subsequent roof falls. In fact, approximately 50% of the first 13 longwall recoveries (which were at depths of 180 to 200m) experienced roof fall delays, the longest of which took four months to mine the last pillar and recover the longwall. This recurring problem prompted the mine to investigate options to reduce or eliminate the problem."

Jan 1, 2016

By Samrat Mohanty

The construction of underground hydrocarbon storage caverns in Jurong Island, Singapore, is nearing completion. The facility, located beneath the seabed of Banyan Basin, is comprised of five storage caverns with a storage capacity of approximately 1.5 million cubic meters. The galleries of each cavern are 20 m wide by 27 m high and approximately 340 m long. In addition to the storage caverns, various access and operations tunnels are required to support the facility. Among these are water curtain galleries to ensure that hydrostatic pressures in excess of hydrocarbon storage pressure are maintained in the rock mass surrounding the storage caverns. Early in the design process, conventional steel rock bolts with resin polymer grout were considered for ground control. However, the construction contractor proposed using fibe-reinforced polymer (FRP) bolts with cement grout due to the corrosive hydrologic environment, weight and handling considerations, local construction preferences, and the requirement to have a cavern design life of 50 years. FRP bolts with cement grout were ultimately chosen for the project. The FRP bolting system has proven to be very successful, with no ground failures experienced where systematic FRP bolting has been applied. This paper discusses the properties of FRP bolt/cement grout bolting systems, their characteristics in relation to steel bolt/resin bolting systems, and numerical modeling results assessing their performance.

Jan 1, 2014

By Bruce W. King, David A. Newman

"Underground mines have always been an integral part of the limestone industry. However, beginning in the 1990s, the number of underground limestone mines has increased for many reasons including• Stripping ratios at surface quarries have become uneconomic.• Existing surface quarries have reached the mineral boundaries, and the remaining stone reserves are underground.• Surface access to the entirety of the limestone reserve is limited by development or infrastructure.• The once-rural setting of the surface quarry is now surrounded by subdivisions and development. An underground mine is less intrusive and takes the mining operation out of the public eye.• For larger markets, an underground mine enables year-round production without the sequence of overburden stripping in the winter to expose mineable stone for summer production. This is common at many surface quarries.Multiple-level operations are a natural extension of the decision to mine underground. Most limestone reserves, for example, the Tyrone-Oregon-Camp Nelson, Hermitage-CartersLebanon- Ridley, and Salem Limestones, are sufficiently thick to accommodate multiple levels. Multiple-level mines should be planned by considering each level separately and then integrating the individual levels into a larger mine plan. Failure to plan all the levels of a multiple-level mine in concert can result in ground control (back, pillar, floor, and inter-level sill pillar) problems attributable to stress transfer and interaction between the levels or the necessity to leave a thicker sill pillar between adjacent levels.Multiple-level mine planning begins with geology. Once the upper level back horizon is identified, the geology, rock strength, and physical properties in each level are used to• identify the optimal back horizon• quantify whether back support is required and, if so, the type, spacing, and length of the back support• determine the pillar centers• determine the total mining height, including floor shots"

Jan 1, 2016

By Peter Hayes

Moonee Colliery operates a longwall extraction system in the Great Northern seam of the Newcastle Coal Measures, approximately 100km north of Sydney, NSW. In the initial mine area of longwall blocks1-4a, the Great Northern seam is overlain by a massive conglomerate approximately 35m in thickness. Unanticipated sudden, blocky caving of this material has produced windblasts with associated velocities of 100m/sec and over-pressures of 35kPa. Although these events have not resulted in fatality, the potential safety risk to face personnel was such that the mine was threatened with closure. The development of a Windblast Management Plan to minimise the exposure to windblasts, a Micro-seismic Management flan to predict caving events, and the use of hydraulic fracturing to generate caving on demand, have all contributed to the salvation of the mine. Prior to the introduction of hydraulic fracturing, falls were highly variable and ranged in goaf area from 2000m2 to 30,000m2 with an average of around 7.000m2. Hydraulic fracturing has introduced consistent and far less variable falls, planned as averaging around 5000m2 and all accompanied by microseismic warning, Moonee Colliery is believed to he the only operation in the world using real-time microseismic warning and using hydrofracturing as a day-to-day operational process. These processes have enabled it to return to financial viability in an environment of strict procedural control, whilst ongoing efforts are made to optimise and enhance these systems. Moonee's story is a case study of the successful application of research and development work to the economics of a mine.

Jan 1, 2000