Search Documents

By James Pile

Since C.C. White introduced coalmine roof trusses in 1967. many different systems have evolved. Beginning in the mid 1990's, several types of bar/cable truss systems have been introduced. A new and innovative bar/cable truss recently introduced offers several advantages. By eliminating many small parts, and simplifying the installation, this new truss increases operator safely. In order to fully benefit from the new truss system, a closer look at the individual components and their interaction was undertaken to understand critical implications on preload and overall support capabilities.

Jan 1, 2004

By Dennis Dolinar

In general, the direction of the maximum horizontal stress in the eastern United States is fairly well defined. However, the variation of the magnitudes of the horizontal stresses is not very well understood. Because the horizontal stresses cause severe ground control problems in underground coal and limestone mines throughout the eastern United States a more complete understanding of how the magnitudes vary would be useful for developing mine design strategies to combat horizontal stress related ground control problems. Therefore, in this National Institute for Occupational Safety and Health (NIOSH) study, the variation of the magnitude of the horizon stresses in sedimentary deposits in the eastern and Midwestern United States are examined with respect to two factors, the elastic modulus of the rock and the site depth. Stress measurements from thirty-seven sites are used in the evaluation. Examining the applied excess strains indicates that the eastern United States can be, separated into high and low strain zones. For most of the eastern United States the maximum applied excess or tectonic strain ranges from only 300 to 550 micro strains. However, there is one area, a portion of the Beckley seam in the central Appalachian region where the strains are significantly higher than the other regions. In this higher strain zone, the maximum applied tectonic strains range from 700 to 1,000 micro strains. Regression models for each zone based on the elastic modulus can explain between 83 to 85% of the variation of the maximum horizontal stress. Because one region, the northern Appalachian district, has strains that are about 20% higher than the other regions in the low strain zone, multiple strain models based on geographic regions were developed for the low strain zone that can explain 87 to 91% of the maximum horizontal stress variation with the elastic modulus. Depth was found not to be a significant causal factor in any increase in the horizontal stress even though the site depths ranged from 275 to 2,500 ft. Beyond a theoretical increase, based on Poisson's effect and gravity, no other increase in the horizontal stress with depth can be justified with this data. The most significant factor controlling the variation of the maximum horizontal stress is the elastic modulus of the rock, not the overburden depth.

Jan 1, 2003

By K. Goshtasbi Goharizi

This paper discusses experimental results of physical scale models employed to study the stability of a pillar between rectangular roadways. A programme of laboratory investigations utilising a bi-axial test rig has been undertaken to examine the influence of various stressfields on the stability of pillars between mine roadways. The effect of pillar height/width ratio on the overall stability is studied. Observations of failure characteristics in and around pillars are discussed especially in relation to the various stressfields applied to the models.

Jan 1, 1992

By Noor Mohammad

Comprehensive numerical modelling of the subsidence associated with longwall mining in UK Coal Measures strata has been conducted and validated against UK data. The Rock Mass Classification System (RMR) was used as the main basis to derive representative in-situ rock mass properties for stiffness and strength parameters for the numerical modelling input. A Finite Difference Method, Fast Lagrangian Analysis of Continua (FLAC) has been used to design a suitable non¬linear model and simulate the behaviour of the caved zone with a unique modification of the post failure properties within the zone of influence. The established model was validated for different configurations, varying depth, panel width and extraction thickness, in a sensible and realistic range. The Subsidence Engineers Handbook (SEH) and a stress abutment model were used as a validation tool in this respect. The approach developed will be modified for application to a number of different International Coalfields with different geological environments.

Jan 1, 1997

By D. F. Howarth

Two innovative ground reinforcement products have been developed for use in the mining industry. One of these products is a high strength polyethylene (HOPE) bar for use as a rib bolt in underground coal mining and as a corrosion proof tendon in open pit mines. The other product is a cable bolt (Ultrastrand) which demonstrates enhanced load transfer and is available in continuous lengths. Ultrastrand's exceptional in¬situ performance and versatility makes it ideal for mechanised installation in both underground and surface mining operations. Details of these products are presented and results from labortaory and field trials are discussed.

Jan 1, 1992

By Richard A. Allwes

A procedure is presented for the design of an arch canopy for the application of rehabilitating a high-roof-fall area. This procedure is specifically developed for evaluating an unbackfllled arch canopy, which Is subjected to an impact load (roof fall). Dynamic line loading of the arch canopy at its crown is only considered and the procedure does not account for an unsymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation is dependent upon many variables, including in-nine conditions and the engineering properties of the structure. However, a general evaluation can be based upon a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. A single spring-mass system is used as an idealized model to represent the dynamic behavior of the arch canopy at its crown. An energy approach is taken to determine the maximum crown deflection of an arch rather than solving a differential equation of notion derived from dynamic equilibrium. The design procedure is based on the concept that when an arch canopy is subjected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure Is that It gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1986

By Wm. Mark Hart

Under a specific geological condition, roof supporting method, and pillar-entry system, an entry convergence concept may be the most effective means that can be used to effectively indicate the longwall entry stability (i.e. pillar bumps, roof falls, or floor beaver This concept may also be used to verify the effectiveness of the current pillar-entry system and roof supporting method. Furthermore, convergence measured under different mining phases may lead to a better understanding of the longwall mining-induced abutment loads and may be used to estimate stress change in pillars and thus pillar stability. In this paper, a remote entry activity monitoring system was designed; a comprehensive entry convergence monitoring strategy was proposed; thee abutment loading phases in longwall mining were defined; the relationship between roof deflection and stress change in a pillar was derived, and finally the extent and magnitude of the mining-induced abutment loads as well as their impact on entry convergence were discussed using the field data obtained so far.

Jan 1, 1995

By Linsheng Xu

When coal seam is under the integral thick sandstone (or conglomerate), the structure of thick sandstone is integral and its strength is rather high. After coal is extracted, the roof is hanging and caving is difficult. When the method of full caving is adopted in the longwall working face to control this kind of hard and difficult caving roof, the effect of roof-controlling affects directly the production and safety. In China Datong Coal Mines the extracting coal deposit is Datong Jurassic period. Most of the roof is sandstone and conglomerate. It is hard and difficult to cave. Having used special hydraulic power supports and other special ways to deal with the roof, the hard and difficult caving roof has been controlled.

Jan 1, 1986

By John C. Stankus

At the 19th International Conference on Ground Control in Mining, a paper was presented detailing new types of Jennmar INSTáL tensionable cable bolts (Stankus and Taylor, 2000). Since that time, significant testing and trials of the various types of tensionable cable bolts have been conducted. Several MSHA districts and state regulatory agencies have now approved these systems as primary support This paper will detail the use of tensionable cable bolts as primary support at two longwall mines in Virginia (MSHA District 5).

Jan 1, 2001

By James M. Kramer

This paper introduces an analytical approach for the determination of the vertical stress in the chain pillar system between two adjacent longwall panels. The development of this approach is based on the principles of fracture mechanics and superposition. Some empirical formulae have also been incorpomted into the development of the mathematical model. The mine entries and longwall gobs are treated as Mode I cracks in an infinite plate while the resistance of gob material and the characteristics of the pillar yield zone are considered as the distributed forces on the surface of the cracks. An user- friendly computer program has been developed to facilitate the calculation involved in this task. This approach is as accurate as the numerical analysis methods but requires much less expertise and computer hardware and software to apply

Jan 1, 1998

By Rob Robinson

Following a massive rib wall failure along the reclaim belt of the large underground surge bunker at CONSOL?s Bailey Mine, a multifaceted, cleanup and rehabilitation effort was initiated to rapidly stabilize the bunker rib walls and place the bunker back into production. Rehabilitation of the bunker included infilling and re-mining of the failed excavation area, installing a system of horizontal tie-back cable bolts, constructing a large knee wall at the base of the rib, reducing water inflow, and providing drainage for rib water. As a result of the coordinated effort, the bunker was safely placed back into production within 38 days. The 7500-ton surge bunker, an engineering feat in itself, was constructed in 2003 to accommodate production surges from two longwalls. In 2005, 14.8 million raw tons passed through the bunker. The 22-foot wide by 75-foot high surge bunker excavation extends as much a 52 feet below the base of the Pittsburgh seam. The bunker excavation measures 325 feet in length, with feeder and reclaim belt excavations extending the bunker excavation by approximately 500 feet. The massive rib roll, which occurred near the bottom of the reclaim belt slope, measured as much as 45 feet high by 60 feet long. Failure of the rib was attributed to progressive failure of a thick claystone unit present near the slope bottom area. Saturation of the claystone by water inflow, high insitu horizontal stress, and pre-existing rock joints were considered contributing factors. Immediately after rib failure, mine production was temporarily rerouted to a parallel belt. Two bulkheads were then constructed 175 feet apart along the reclaim belt slope, and a customized fly ash-cement mixture was pumped from the surface into the unstable reclaim slope area. A tunnel was then mined through the backfill along the original reclaim slope contour; the new excavation supported by a system of customized steel sets. To assure stability of the adjacent bunker rib wall, a pattern of 70-foot long cable bolts were installed downward from the adjacent entries to effectively tie back the rib. Drainage holes and a 12-foot high knee wall were installed. Adjacent gas wells were also plugged to help reduce inflow. Periodic inspections and continuous monitoring are being used to help assure bunker stability.

Jan 1, 2007

By H. N. Maleki

This paper presents a field evaluation of six tailgate secondary support systems, with the objective of optimizing support efficiency for maintaining open gate roads. Support systems consisted of a combination of three wooden crib configurations, with either tension rebars or truss bolts. The effectiveness of the support systems was evaluated through measurements of ground movements, support load, and observations along 2000 linear ft of a tailgate. It was concluded that floor heave, crib width to height ratio, cribbing pattern, and support spacing have significant impact on tailgate stability and access after the passage of the first longwall face. Guidelines were suggested for selection of secondary support for other applications.

Jan 1, 1986

By M. Guana

Island Creek Corporation is predominately an underground mine operator deploying room-and-pillar and retreat longwall mining methods for extracting coal. Wide variations are encountered in overburden depth, stratigraphy, and insitu stress fields. This requires major adjustments in mine design among mines and occasionally within a mine. Simple rock mechanics principles are utilized in mine design to optimize safety and productivity. Physical observations and micro deformation monitoring of roadways are the primary techniques employed. Pillars and artificial support systems are the primary design elements modified. The specific case histories reviewed in this paper include narrow panels with high extraction for conventionally mined rooms, pillar sizing for longwall gate entries at great depths, and bolt type selection for difficult ground conditions.

Jan 1, 1988

By Bob Thomas

The roof drill operator productivity can be enhanced by the introduction of control technology The operators control station can be improved by considering human factors such as handle forces and control location. The smaller electrical controls can be located much easier than the traditional hands on valves. The operators control can he improved by using processors with programmable subroutines that assist the operator in the decision making process. For example to increase feed rate - to slow rotation - to avoid clogged steels - etc. The overall affect is to improve drilling and bolting consistency. The control system uses a dedicated processor packaged as an intrinsically safe control station. The roof drill operator is assisted in the drilling; arid bolting by a closed loop feedback system. The processor monitors the drilling parameters such as feed force, feed rate, rotation torque, RPM, drill position, and vacuum condition Based on the drilling parameters the processor executes pre-determined condition statements intended to enhance drilling The drill operator has an active display to alert him to the real time machine status. For example if the feed were to slow or delay due to a high vacuum level the display would show "high vacuum". The dedicated processor is available on the arm feed style machines, The prototype machines used programmable logic controllers to develop the feedback relations. The ability to record drilling parameters was extremely helpful in this development project. The extended use of the recording feature will aid operators in mapping the mine roofs Interpreting the recorded drilling parameters can reveal a void in the top or hard competent drilling The prototype machines also showed the importance of vacuum monitoring This feature is extremely valuable in softer materials, The benefits of the control system range from efficient use of the consumable bolting materials to uniform operator performance.

Jan 1, 1999

By Lance R. Barron

The U.S. Bureau of Mines, in cooperation with a central Utah coal .mine operator, began a study in July 1988 into longwall gateroad designs applicable to deep, bump- prone mine conditions. Prior to the study, four adjacent longwall panels, incorporating a variety of panel entry configurations using "yielding' chain pi liars, experienced severe bumps and coal outbursts at the face and in the tailgate pillars during panel extraction, resulting in several lost-time accidents and a fatality. To quantify those factors primari1y responsible for bump occurrences during panel retreat, a field investigation was initiated to confirm the anticipated performance of a two-entry gateroad system employing a large, nonyielding chain pillar design. Hydraulic borehole pressure cells and roof-to-floor closure [convergence) measurement stations were installed to monitor gateroad abutment loading and entry closure during panel extraction. Study results indicate that very high confinement of the coal seam by strong roof and floor members existing across the entire property, in conjunction with overburden depths in excess of 1.600 feet, provides for bump-scale energy storage in not only gate pillars, but along the entire periphery of the active mining area. Insufficient gate pillar designs were also identified as possibly enhancing the occurrence of bumps in the tailgate and adjacent face areas.

Jan 1, 1990

By Stephen C. Tadolini

A new innovation in coal mine roof support has been developed by the Bureau of Mines at the Denver Research Center. The technique, called "Thrust Bolting,"1 converts a traditional passive roof support system, a full or partial column rebar bolt, into an active support system by following a specific installation process. The thrust bolting system provides two advantages from a ground control standpoint. First, because the system is active, no roof movement is necessary to put the bolt into tension. This eliminates the possibility of strata separations in sedimentary roots, minimizing progressive-type roof failures. Secondly, the tension placed on the system is independent of mechanical devices or torques. This eliminates the highly variable frictional losses that occur between the bearing plate and the bolt head and in the threaded portions of traditional active support systems. These two improvements create a safer working environment for mining personnel. An additional advantage of this improved support system is the reduced cost of installation and maintenance. The initial support cost is reduced by a minimum of 30 percent per bolt when compared to similar conventional support systems. The labor intensive and potentially hazardous torque¬tension test, required for most tensionable active support systems, is not required for thrust bolts. The potential for improved support performance and cost reduction of thrust bolting has generated a considerable amount of interest from both industry and MSHA. This paper will describe, in detail, the theory and application of thrust bolting and present the results of two underground coal mine case studies.

Jan 1, 1990

By Stanislaw Prusek

The present state of Czech and Polish coal mining industry is presented at the beginning of the article. This paper will inform the reader of the general data concerning hard coal reserves? number of mines, number of miners, output, number of longwalls, productivity, depth of extraction, and extraction methods?in both countries. The main part of the paper describes the methods of gateroad development as well as gateroad support characteristics (support types, gateroad shape and dimensions, distance between support sets, types of reinforcements). The development prospects of gateroad support in the Czech and Polish coal mining industry are also presented.

Jan 1, 2011

By Daniel S. Mazzei

This paper will be a general discussion of surface flooding considerations as they affect mining facilities site selection, based primarily on experience with several such problems with which MSHA's Bruceton Technical Support staff has been involved. The detailed analytical procedures used in arriving at engineering solutions of these problems will not he presented here; the emphasis is on drawing attention to this additional aspect of mine design which hitherto has been largely overlooked due to insufficient awareness, information and criteria. The paper's purpose is to stimulate thought and offer guidance concerning the selection of sites for mining facilities in light of the potential for flooding problems caused by surface waters. Flooding by surface waters, would generally not be a serious consideration in areas of relatively low topographical relief, i.e. flat lands, although there are exceptions to this rule, for example, in Western areas where flash flooding is a major concern. Therefore, this discussion will mainly apply to areas where the severity of surface flooding would be amplified by the topography-large, well defined watersheds of considerable relief, i.e. mountainous areas. In these regions, steep valley walls cause any rainfall to flow quickly into the relatively narrow valley bottoms. These valley bottoms provide little flow area during storm conditions, so deep and rapidly flowing streams result.

Jan 1, 1982

By Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs. Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads. Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

Jan 1, 1999

A procedure fm the estimation of pilla1 strength is presented where the design of underground coal pillars is emphasized. An analytical approach has been developed, proposing that the effect of end constraints on the pillar strength and the ductile behavior of coal material should be incorporated in the computation of the stability of coal pillars. Bad on this approach, it has been found that end constraint has a significant influence on the pillar strength. The study indicates that when the end constraint is zero the computed strength of the pillar is the same as the unconfiied compressive strength of the coal mass and will not increase with the increase in the width to height ratio. However. when the end constraint is greater than zero the pillar strength will increase exponentially as the width to height ratio increases.

Jan 1, 1990