Search Documents

By Sebastiaan Peelman

NdFeB permanent magnets are the best available magnets used in many technology applications. However, at their end-of-life (EoL) most of magnets and the contained REEs are lost during the recycling of the bulk metals. The REEs are classified as the most critical raw materials in the European Union, and recycling of REEs from EoL products will reduce their criticality and contribute to the sustainability of REE. Various technological routes have been reported, but most of the methods are effective for highly concentrated magnets or magnet scrap, which is greatly dependent on expensive pre-dismantling processes. This paper presents various innovative metallurgical solutions to the effective REE recovery from current industrial practice for WEEE recycling, including the ferrous scrap from WEEE shredder products and shredder residues from computer hard disk drives. Both hydrometallurgical and combined hydro- and pyrometallurgical REE recovery routes are developed after demagnetization and physical upgrading.

By Christopher M. Moore

DK Recycling und Rohelsen GmbH converts 380 000 annual tonnes of iron containing waste materials Into pig Iron. Zinc Is the main reason that these materials are classified as waste. The materials are processed In the conventional way by making sinter which is then smelted in a blast furnace to foundry grade pig iron. The trick lies not in the unit operations which are quite standard but rather In the modifications made to the plant and operating procedures to cope with the much higher levels of tramp elements.

Jan 1, 1995

By Gil Bourcier

A process has been developed for detoxifying spent potliner (SPL) in which the SPL is blended with limestone and an anti-agglomeration agent and thermally treated in a rotary kiln. The process has been proven and a commercial plant is in operation at Gum Springs, Arkansas. The treated by-product material has been delisted by the U.S. EPA and is now a potential raw material for many commercial applications. Finding uses for a non-hazardous material has many advantages over finding uses for a hazardous material like SPL. Complete usage of the by-product will complete the life cycle and eliminate any landfilling of non-hazardous SPL by-products or residues. Being non-hazardous and containing compounds used in the ceramic and numerous other industries assures many potential uses for the spent potliner by-product.

Jan 1, 1994

By C. A. Silva

The kinetics of chlorination of titanium-bearing raw materials has been investigated. For comparison purposes pellets of controlled macro-porosity, made of analytical grade TiO2 and anatase concentrate (Brazil) , have been exposed to different combinations of gas composition - CO, CO2, C12 -, gas flowrate and temperature. A thermogravimetric technique and an adapted grain model have been used in order to assess the influence of the several experimental parameters upon the chlorination behavior.

Jan 1, 1997

By Jr. Napolitano, Jr. Sanders

"Morphological evolution of a dendritic growth front in a binary alloy is simulated using a cellular automaton approach to establish the feasibility of modeling such growth with a local rule-based scheme. The motivation for this work is derived from the need to predict the development of solidification structures within real components of complex geometry, where significant constraint of the thermal and solutal fields may exist. Such cases present complex boundaries and large domain sizes, which may preclude the effective use of more conventional methods. In this work, a model is presented which couples a two-dimensional alternate-direction-implicit finite-difference diffusion solution with a cellular automaton growth algorithm to simulate morphological evolution in alloys solidifying under directional growth conditions. Temperature, composition, and interface curvature are incorporated into a local growth potential which is used by the automaton, allowing the interface to evolve. Alloy solidification is simulated over a range of experimental conditions, producing various structures. Issues addressed include morphological instability, primary spacing selection, interface curvature, microsegregation, and tip conditions.IntroductionThe development of dendritic structure plays an essential role in alloy solidification. Virtually every microstructural feature, within a cast alloy component, is related to the interface morphology present during solidification. Conventional solidification theory, describing dendrite tip kinetics and mushy zone phenomena, provides a means for estimating overall microstructural parameters for an alloy solidified under steady-state conditions. Microstructural prediction for actual components, which are finite in size and complex in geometry, requires a description of the evolution of the interface morphology under transient conditions and geometrical constraint and an understanding of how the structure propagates through the mold. Any useful simulation tool must be equipped to handle these circumstances within the limits of computational feasibility."

Jan 1, 1998

By Elli Miettinen

In Copper Flash Smelting operation disturbances may lead into dust build-up in the gas train and off-gas handling system causing reduced heat recovery efficiency and process availability. Flue dust of a Copper Flash Smelting process heat recovery boiler has been characterized and its thermal conductivity and diffusivity have been determined. Dust accretions consist of several layers possessing varying particle sizes, densities, and thermal properties, with the binding phase usually being sulphate. All the dusts can be regarded as effective thermal insulators with thermal conductivity values of less than 2 W/mK and thermal diffusivity values of less than 0.005 cm2/s. Porosity can be regarded as a fairly good indicator of the thermal transport efficiency of these types of materials, but the material microstructure must also be considered. The results can be used in the dimensioning of metallurgical heat recovery boilers and they also provide accurate input data for process models.

Jan 1, 2009

By Yasuhiro Konishi, Yoshiyuki Noda

"This paper describes a new processing of rare-earth oxide precursor, in which rare-earth carbonate powders are precipitated directly from emulsions of rare-earth loaded carboxylate solutions, using CO2 gas and water. This synthetic route of rare earth carbonate is a combined process of the stripping and precipitation stages in a conventional solvent extraction. Using this technique, lanthanum carbonate and yttrium carbonate were prepared at temperatures of 10 to 80°C and CO2 pressures of 0.1 to 3.0 MPa for 120 min. The rates of carbonate precipitation in a batch autoclave were sensitive to processing parameters such as CO2 pressure, temperature, and organic-phase composition. The particle size distributions of the carbonate powders were markedly dependent on temperature and C02 pressure.IntroductionSolvent extraction is the most appropriate commercial technology for separation and purification of rare earths. In typical commercial processes, the rare earths are stripped from loaded solvent extractants using aqueous solutions of mineral acid. After adjusting the pH of the aqueous strip solution, the rare earths are precipitated as insoluble powders of oxalates or carbonates, from which oxides can be produced by calcination. Such conventional processing can be simplified when the stripping and precipitation stages are combined by emulsifying rare-earth loaded solvent extractant with aqueous oxalic acid solution. It is likely that the single-stage precipitation stripping results in a marked decline in the consumed amounts of precipitating and neutralizing agents, thereby saving on both running and capital costs.Yoon and Doyle1) first demonstrated that oxalate powders of lanthanum and yttrium are directly precipitated from rare-earth loaded carboxylic acid solvent extractant when contacted with aqueous oxalic acid solution at ambient temperature and atmospheric pressure. Yttrium oxalate pow4ers were also prepared by precipitation stripping of di-(2 ethylhexyl) phosphoric acid. (D2EHPA) extractant using oxalic acid-hydrochloric acid solutions. 2) Moreover, neodymium oxalates were directly precipitated from organic solutions of tertiary aliphatic monocarboxylic acid and 2-ethylhexyl phosphonic acid mono-2- ethylhexyl ester using aqueous oxalic acid solutions, and powder characteristics of the resulting oxalates were compared with those of powders by the conventional solvent extraction routes. 3 • 4) Recently, attention has been directed towards the influence of processing parameters on the particle size distributions of yttrium oxalate precipitates. 5)"

Jan 1, 2000

By Brian G. Thomas

Quality problems in continuous casting of steel can be identified as they occur by monitoring mold signals (level sensor, thermocouples in the mold walls, friction etc.) and taking appropriate action (such as slowing casting speed, changing taper, changing a clogged nozzle, or later visual inspection of the surface for possible downgrading. Surface depressions and groups of deep oscillation marks form at meniscus and reduce local heat transfer as they move down the mold at the casting speed. This slows shell growth, increases shell surface temperature, and causes characteristic dips in mold thermocouple signals. More importantly, they are also associated with longitudinal cracks. Characteristic thermocouple signatures have been identified for many defects, including sticker breakouts, transverse depressions and deep oscillation marks, narrow-face bleeds, transverse comer cracks, longitudinal cracks, mold level fluctuation defects, and other problems. With the help of computational models, these mold signals should be used to troubleshoot defects, and to take appropriate corrective action. Keywords: Continuous casting, defect detection, thermocouple signals, on-line control

Jan 1, 2003

By E. S. Peterson

The selective separations of trace metals- and organics from water are processes of importance to industry. The application of a new metals capture technology coupled with polymer membrane technology has proven to be one avenue to accomplish such selective separations. The polymers used in these studies are polyphosphazenes. Polyphosphazene polymers consist of an alternating backbone of nitrogen and phosphorus atoms. The polymers have high thermal and chemical stabilities. Experiments at the Idaho National Engineering Laboratory demonstrate that polyphosphazene membranes coupled with Chromato Chem,"Chelation Chromatography" process are capable of removing both chlorinated hydrocarbons and metal ions from process streams. These results point to a wide range of potential industrial and environmental applications for such systems. Data will be presented which show the efficiency and selectivity of separations, postulated separation mechanisms, and the initial designs of industrial demonstration units which are currently under construction. Parts of this work have been performed under a Cooperative Research and Development Agreement (CRADA) between ChromatoChem, Inc. and Idaho National Engineering Laboratory (INEL). The work at INEL was been sponsored by the United States Department of Energy's Office of Industrial Technologies

Jan 1, 1995

By Ming Li, Li Ma, Yunqing Tian, Haoyu Cai, Luyao Zhao, Wenwang Liu, Wenbin Huang, Gele Qing, Yan Zhang

In this paper, study on the in fluences of different Ti-bearing materials on MgO-bearing pellets metallurgical properties was carried out. The results show that, pellets compression strength will decrease while using ilmenite. However, TiO2 reagents help to improve pellets compression strength. The reduction swelling decreases while using TiO2 reagents, but different ilmenites have diverse impacts on the reduction swelling. Pellets compression strength will decrease and reduction swelling will be improved while adding magnesium additives. In order to produce qualified Magnesium-Titanium bearing pellets, the firing temperature should be no less than 1270 °C.

Mar 1, 2018

By Batric Pesic

Silver dissolution with thiourea was studied by using the rotating disk technique. The major parameters studied were: thiourea concentration (0-0.5M), ferric sulfate concentration (0-0.5M), sulfuric acid concentration (0-0.5M), and the effect of many foreign ions (Mn, o.i, Co, Ca, Na, etc.). Temperature effect was studied in the range 5-35 .C. The activation energy was 5.4 Kcal/mole. The dissolution of silver was first order with respect to ferric sulfate, and the secord order with respect to thiourea. Among the additives, copper had a dramatically negative effect. The strong oxidants such as hydrogen peroxide and manganese dioxide were also detrimental for silver dissolution. Silver does not dissolve with thiourea in the absence of ferric ions. Sulfuric acid does not participate in the dissolution reaction either. Chemically, the most important parameter for silver dissolution is the ferric sulfate/thiourea ratio. Thus, in the solutions with excess of ferric sulfate, a solid silver-thiourea complex is formed, which precludes transfer of silver into solution. In the solutions with the excess of thiourea, the free thiourea reacts with formed solid silver-thiourea complex and silver goes into the solution. The solid silver-thiourea complex was characterized according to its chemical composition. The complex contains 6.54%C, 2.49\H, 14.77%N, 16.09%0, 21.62%8, and 37.13% Ag. This composition corresponds to a Ag2so4.3'1U.2ff:i0 compound The soluble silver species are present in the solution as the dimers of AgTU+3 complexes.

Jan 1, 1989

By Lincoln McCrabb

Correct measurement and interpretation of viscosity data is critical for design of any thickening and pumping process that involves a non Newtonian slurry. The nickel laterite pressure acid leach (PAL) process relies on producing a slurry of maximum achievable solids concentration. Small variations of 1-2% solids concentration can alter economics significantly. For the Ravensthorpe Nickel Project, a rheology protocol has been developed which optimizes the solids concentration across a range of ore types. The vane yield stress technique has been utilized to accurately quantify the flow of thickened slurry in the lower shear range. A yield stress of 100Pa has been used as a benchmark to determine the optimum solids concentration achievable utilizing deep cone thickening. Statistical analysis of the data shows critical rheology distinctions between ore type, particle size, lithology and geochemistry. Linear and power law models have been applied to rheology flow curves to reconcile the material transport properties with the anticipated thickener underflow solids concentration. Keywords: Vane Yield Stress, Thickening, Rheograms

Jan 1, 2004

By Nathanael Hudson, Ruel A. Overfelt, Sushil H. Bhavnani

"In the aerospace and automotive industries, complex shapes exist which require casting. The problem with these cast parts is the empiricism required to develop the casting process and the accompanying time and expense to develop that process.There has been an interest in using fluidized beds to allow molding sand to better encapsulate the complicated surface geometries of lost foam patterns. Fluidization coupled with a mixing jet helps to homogenize the sand through stirring and may improve the integrity of the casting.At issue is the hydrodynamics of the sand and air around the foam pattern. The commercial package PHOENlCSTM is used to simulate the flow around the pre-casting foam geometry. Employing a two fluid approach, each component is considered a fluid that interpenetrates the other phase. To this end, the kinetic theory of granular 'flow for the sand phase was incorporated into the re-compilable PHOENlCSTM code.The results of this study consist of time-averaged void fraction patterns, with voidage being defined as the fraction of air in the mixture, around the foam pattern submerged in a two-dimensional fluidized bed. The model was benchmarked against past fluidized bed experiments. In order to better understand the dependence of the void fraction pattern around the lost foam pattern, certain physical parameters are varied and the resultant void fraction maps are predicted with the model. Physical parameters such as the aspect ratio of length to width, the placement of the mixing jet, and different mixing jet velocities are varied to illustrate the dependence of the time-averaged void fraction on those variables.Results consistently indicate the presence of channeling around the lost foam pattern, with the extent of the channeling and void formation reliant to a greater degree upon the placement of the mixing jet, and to a lesser degree on mixing jet velocity and aspect ratio.The increase in radial position of the mixing jet from the bed centerline had the desirable effect of granting the churning benefits of a penetrating jet, while at the same time minimizing the formation of excess void fraction at the top of the pattern."

Jan 1, 2001

By Nils Lippmann, Ulrich Weber, Siegfried Schmauder, Jr. Mishnaevsky

"A computational approach to the optimization of fracture resistance of multiphase materials (here - high speed steels) by varying their microstructure is presented. The main points of the optimization of steels are as follows: (1) development and verification of the model: numerical simulation of crack initiation and growth in real microstructures of steels, (2) computational experiment: simulation of crack growth in different idealized quasi-real microstructures and (3) the comparison of fracture resistances of different microstructures and the development of recommendations to the improvement of the fracture toughness of steels. Numerical simulations of crack growth in real microstructures of steels and different idealized carbide distributions are carried out. On the basis of the simulations, recommendations for the improvement of high speed steel microstructures are given. It is shown that the fracture resistance of the steels is much higher for the fine than for the coarse version of the same type of microstructures.IntroductionThe purpose of this work is to develop an approach to the optimal design of multiphase materials on the basis of numerical simulation of their behaviour under mechanical loading. We suggest here the following strategy:1. Collecting input data for the simulations: taking a micrograph of a microstructure, and determining mechanical properties and failure conditions of the material constituents [1, 2],2. Simulation techniques and assumptions are tested for a real microstructure of the material: crack growth in a real microstructure is simulated and then compared with the experimental data,3. Computational experiments: different microstructures of materials are tested in the numerical model under the same loading conditions. The calculated service properties of the different microstructures are compared, and recommendations are developed. As differentiated from the ""real"" experimental techniques, the computational experiment is much cheaper and not labor- and time-consuming."

Jan 1, 2001

By Jay R. Hitchings

A technique that enables excellent color photograph production from black and white negatives of electron microprobe x-ray images is described in this paper. The photographs are made by superimposing one, two or three negatives of black and white x-ray images individually through assigned primary color filters directly onto color print paper. When used to examine metallurgical or geological microstructures, the resulting color photograph provides detailed, qualitative information about spatial arrangements, elemental associations and relative concentrations of at least three elements. The technique is simple and straightforward, requiring only standard darkroom equipment. The use of color to display or present complicated microprobe data also allows a non-technical reader or audience to better understand the data.

Jan 1, 1981

By Kenneth L. Reid

The Mineral Resources Research Center at the University of Minnesota has recently installed a QEM*SEM system (Quantitative E.valuation of Materials using Scanning Electron Microscopy) to aid in detailed mineralogical evaluation of potential mineral resource developments in Minnesota and to provide services to the North American mineral industry. A primary application for the unit is to serve the Minnesota taconite industry by providing mineralogical analysis of ores and concentrator products. Minnesota taconite ores contain fine-grained magnetite in a quartz matrix. The ores undergo several size-reduction/magnetic-separation steps to produce a final concentrate with approximately 75% passing 325 mesh and containing about 5% gangue. The paper describes a typical taconite concentrator flowsheet and reports some preliminary results of the applications of QEM*SEM particle image maps and cumulative yield liberation data to samples from selected points in the concentrator circuit.

Jan 1, 1988

By Mao Chen, Tim Evans, Zhixing Zhao, Weidong Zhang, Baojun Zhao, Dongqing Wang

High temperature softening behaviours of iron blast furnace feeds (sinter, lump and pellet) have been determined under conditions simulated to the blast furnace. The industrial samples were packed with sandwich structure (coke / ore / coke) in graphite crucibles and 30 CO / 70 Ar gas mixture was blowing directly through the bottom of the crucibles. The displacement and temperature were continuously recorded simultaneously to construct the softening curves. Separated quenching experiments were also carried out at selected temperatures under the same gas atmosphere. The temperatures were selected corresponding to the turning points of the softening curves. The phase assemblages and composition of each phase in quenched samples were analysed by Electron Probe X-ray Microanalysis (EPMA). The proportion of the liquid formed at temperature was obtained from the backscattered electron images. The deformation characteristics of these complex multi-phase materials are shown to be related directly to the phase assemblages of the samples and the microstructures. FactSage was also used to assist the predictions of liquid / solid fractions and their compositions.

Jan 1, 2015

By J. A. Innes

"""The oxygen, next uniting with the carbon, sent up an ever-increasing stream of sparks and a voluminous white flame. Then followed a succession of mild explosions, throwing molten slags and splashes of metal high up into the air, the apparatus becoming a veritable volcano in a state of active eruption.""IntroductionHenry Bessemer F.R.S(An autobiography, 1905)Thank you Mr Chairman for the opportunity to speak: at this, the opening session of your International Symposium on the subject of ""Injection in Pyrometallurgy"". Judging from the list of papers to be presented over the next three days, the Symposium promises to provide a most valuable addition to our existing knowledge base in what is now an extremely active area of R&D investigations. Whilst we have obviously come a long way since Sir Henry Bessemer's pioneering experiments of the mid-19th century, there is still much for us to learn.Most importantly, the Symposium offers a further opportunity to acknowledge the many significant technical contributions made in this field by the Organising Committee's special guest, Professor Howard Worner - one of this country's most respected research leaders.When first approached to give this talk I had two areas of concern. Firstly, I was not entirely clear just what injection metallurgy was meant to cover. How should the overall scope of this particular subject be defined?My second concern related to Howard Worner himself - a man for whom I have the highest personal regard and who, in fact, played a most influential role in respect of shaping my own career. Having already spoken about Howard's achievements on earlier occasions, I wondered what I could sensibly add.Notwithstanding these personal reservations, I am delighted to be here with you this morning. If my thoughts on the meaning and scope of injection metallurgy appear to be slightly off-course, and if Howard should perhaps recognise some repetition in my remarks, then I hope I can be forgiven."

Jan 1, 1996

By S. Sundarraj

The morphological transition between columnar and equiaxed structures is an important solidification phenomenon frequently observed in castings, especially complex parts with varying cross-section, The mechanical properties and the occurrence of defects such as hot tears are strongly dependent on the structure formed in the casting. Hence, it is important to understand the conditions leading to columnar or equiaxed structures. Although extensive work has been done in modeling solidification systems, almost all of the existing models are based on the assumption that the structure formed in the casting is either purely columnar or purely equiaxed. Prediction of the columnar-equiaxed transition (CET) requires a solidification model which accounts for the formation of both columnar and equiaxed structures, along with related microscopic and macroscopic solidification phenomena. In this paper a CET model is presented which: (i) takes account of both columnar and equiaxed structures, (ii) accounts for macroscopic heat transfer coupled with microscopic phenomena such as nucleation, growth and microsegregation, (iii) satisfies solute conservation, and (iv) is easy to implement in commercial finite element and finite difference software. The proposed model predictions of CET have been validated with available experimental results for a uni-directional solidification of an aluminum-copper alloy. A sensitivity analysis has also been carried out to determine the effects of various parameters on the CET model predictions. The model is being extended to other alloy systems and more complex geometries. This work will be published in due course.

Jan 1, 1996

By Carl A. Kuehn

At Carlin, Nevada, non-indigenous hydrocarbons were introduced as a bitumen phase which was mobilized due to burial under the Roberts Mountains allochthon. similarly, some indigenous organic matter was locally mobilized. Fluid inclusion and paragenetic data of veinlets formed during this hydrocarbon stage, combined with quantitative modelling or organic maturation, indicate that host rocks had evolved past dry gas conditions of around 1550 and l.l+0.2 Kb in the presence of CH4-saturated, highly saline brine by no later than early to middle Cretaceous time. All hydrocarbons present would have been rendered immobile under these catagenic conditions. Crosscutting relationships at several scales suggest that hydrocarbon mobility may have ceased prior to the intrusion of a series of dikes in the mine which have subsequently been altered and mineralized. Apart from subsequent oxidation, the current distribution and high maturity of carbon-rich zones were established prior to gold introduction. No Evidence has been found supporting proposed hydrocarbon "remobilization" during or after gold mineralization and alteration. The high density of the CH4-bearing fluid requires formation at high pressures (near 1 Kb) and precludes their formation as a result of the "cracking-off" of CH4 from organic matter during a thermal event associated with a shallow hydrothermal system. The density and composition of the fluid inclusions restricted to the early hydrocarbon-stages of the Carlin paragenesis are not unique to the sediment-hosted gold deposit environment of north-central Nevada. Similar inclusions are found in authigenic quartz crystals from Paleozoic carbonaceous shales in central Pennsylvania which have experienced normal metagenesis of indigenous organic matter due to deep burial.

Jan 1, 1987