Search Documents

By J. -C. Tedenac, C. Colinet, X. Tao, P. Jund, R. Viennois

"We report an ab-initio study of the stability and electronic properties of transition metal silicides in order to study their potential for high temperature thermoelectric applications. We focus on the family M5Si3 (M = Ta, W) which is stable up to about 2000 °C. We first investigate the structural stability of the two compounds and then determine the thermopower of the equilibrium structure using the electronic density of states and Mott’s law. We find that W5Si3 has a relatively large thermopower but probably not sufficient enough for thermoelectric applications.IntroductionIn the search of new sustainable energies, thermogeneration of electricity is one of the promising ways, notably because it is able to produce electricity from different kinds of heat wastes and to its portability. However, despite recent progress in the field, the state-of-the art materials have specificities making their mass-production difficult or even impossible: toxicity (thallium, chalcogen or/and pnictogen based alloys), weak abundance (tellurium based alloys) or cost (germanium or rare-earth based alloys). For all these reasons, finding thermoelectric materials without these drawbacks is vital if we wish to use high temperature thermoelectricity for generating electricity in the near future. Due to their abundance, low cost and low toxicity, transition metal silicides are candidate materials of primary interest and the slightest advance in this field would immediately find an application for the thermogeneration of electricity."

Jan 1, 2011

By Hiroshi Nakajima, Kotobu Nagai, Toshihiro Hanamura

"Low carbon ferritic steel bars with ultra-fine grain structure was developed through a warm rolling for the first time by the present authors. They show better low temperature toughness than conventionally hot-rolled plates. Hence, the brittle fracture surfaces in Charpy tests were examined in terms of the effective grain size of fracture, compared with those of conventional QT steels. The ductile-to-brittle transition temperatures were in good accordance with those for the QT steels if referred to the effective grain size of fracture: · However, the size was a few times that of the ferrite grain. This means the grain refining is not yet fully utilized from the viewpoint of low temperature toughness. The anisotropy of· the impact properties and the annealing effect of highly dislocated structure on the toughness are also discussed in the present paper.IntroductionFor structural materials, both high strength and good toughness are required. Well-known approaches for obtaining better toughness for steels are as follows:1) Grain refining2) Addition of Ni3) Thin plate effect by cracking parallel to the rolling direction prior to crack propagation4) Contribution of metastable austenite.Among them, only the grain refining can raise the strength and improve the toughness. And it is well known that the finer the ferrite grain size, the lower the ductile-to-brittle transition temperature. For example, in the case of 0.11 carbon steel, the transition temperature decreases linearly to in d 1/2 [1 ]. However, these have been told in the regime of coarse grain size that is larger than 10 µm in diameter. There ~as .been no study dealing with the low temperature toughness in the regime of ultra-fine grain size with a diameter in the order of 1 µm."

Jan 1, 2000

By Bin Xu, Qian Li, Ya-xuan Wang, Yong-bin Yang, Xi Zhang, Tao Jiang

The effects of common associated sulfide minerals including pyrite, arsenopyrite, galena and sphalerite on thiosulfate leaching of gold were studied in this work. Sulfide minerals had significant effects on gold leaching because that the dissolved products of sulfide minerals precipitated on gold surface to form coating layer. The degree of sulfide minerals impact on gold dissolution decreased in the order of pyrite ≈ galena > arsenopyrite > sphalerite, while the degree of effects on thiosulfate consumption decreased in the order of pyrite > arsenopyrite > sphalerite > galena. The additive CMC (Carboxymethyl cellulose) could not only reduce thiosulfate consumption but also increase gold dissolution. The mechanism of this might be that CMC could restrict the decomposition of thiosulfate by cupric ions and the precipitates on gold surface.

Jan 1, 2015

By Anna Franzkowiak, Dean Gregurek, Alfred Spanring, Angelika Ressler

In order to determine the most suitable refractory products and improve the lining lifetime for the diverse furnaces used in the nonferrous metal industry, corrosion tests are performed at RHI’s Technology Center. The practical facilities include the cup test, induction furnace, rotary kiln, and drip slag test described in this paper, which enable a comprehensive understanding of the chemo-thermal brick wear on a pilot scale. The corrosion trials are performed with actual slags generated during operations at a customer’s plant. To determine the highest influencing wear parameter, every single test is combined with a detailed mineralogical investigation and thermochemical calculations performed using FactSage. Based on the results, tailored refractory solutions for the nonferrous metal industry can be provided in combination with trials conducted at the customer’s site.

Jan 1, 2014

By Roger Wilmoth

Exposed, open pit mine highwalls contribute significantly to the production of acid mine drainage (AMD) thus causing environmental concerns upon closure of an operating mine. Four innovative technologies were evaluated under the U.S. Environmental Protection Agency?s, Mine Waste Technology (MWTP), Prevention of AMD Generation from Open-Pit Highwalls Demonstration Project. This project is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy (DOE) through an Interagency Agreement. The objective of the field demonstration was to evaluate the technologies ability to decrease or eliminate acid generation from treated areas of the highwall in comparison an untreated highwall area. The field demonstration was performed at the Golden Sunlight Mine (GSM) a subsidiary of Placer Dome U.S., located near Whitehall, Montana. GSM is an operating gold mine. The highwall at GSM was divided into five plots measuring 15.24 by 15.24 metres (m) and each technology was assigned a plot with the fifth plot being used for comparison as a background control plot. The four technologies were spray-applied. The applied insitu treatment technologies included: 1) A modified, furfuryl alcohol resin sealant, utilizing wood and agricultural by-products to coat the rock surface. 2) EcobondTMARD, a phosphate based process that forms a stable, insoluble compound, coating the rock surface. 3) Two ARD passivation technologies, magnesium oxide and the Dupont technology developed to create an inert layer/coating on the pyrite, preventing oxidation. The technologies were evaluated using the following methods: 1) ASTM D 5744-96, Accelerated Weathering of Solid Materials using a Modified Humidity Cells, 2) mine wall residual wall rinse sampling, 3) microscopy, and 4) core drilling followed by water injection testing.

Jan 1, 2003

By Zhiqian Zhang, Chao Wu, Chao Li, Hongxu Li, Yu Chen, Xiangxin Hao

"In this paper, the life cycle assessment models for automobile lightweight materials including high-strength steel, aluminum alloy and magnesium alloy are developed by Gabi software. The evaluation models and evaluation indicators such as acidification effects, rich eutrophication effect, ozone layer depletion effects, global warming, resource consumption and formation of ozone potential were taken into account. It is shown that the effects of acidification and ozone formation are mainly derived from the run phase of high-strength steel and they have strong environmental impact load. While considering the entire life cycle with materials production phase and resource consumption, the aluminum and magnesium alloy appe art o have large r environmental load than high-strength steel. Base d on the evaluation, some optimization tips are proposed.IntroductionAs the increasing of car ownership, automobile has its two sides. One which is the convenient, efficient and fast traffic vehicle; the other is aggravating energy consumption, emissions and environmental pollution. The car industry faces heavy pressure with energy saving, safety and environmental protection. Nowadays, the main study ways for automotive energy-saving and environmental protection are power system improvement, alternative energy sources and technologies. For limitation of technique, development cycle and market share, the development of car is little progress at this stage and the application has been restricted. And another important way is the lightweight of vehicle. Usually there are three ways to get the lightweight automobile body structure, automobile body structure optimized design, using advanced body manufacturing technology, development and application of lightweight high strength body material.The life cycle assessment (LCA)[1lis commonly used to evaluate environmental factors and potential environmental impacts of products and services. As an environmental management tool of product-oriented, it becomes increasingly popular in industry. In this study, the concept of LCA and GaBi software was used to develop models for the three automotive lightweight materials, evaluate the environmental impact and make horizontal and vertical contrast by choosing variety of evaluation systems and indexes."

Jan 1, 2013

By Manuel Alvarado, David Nemir, Jan Beck

"Thermoelectric generation using special N-doped and P-doped semiconductors is well known as a means for direct heat energy to electrical energy conversion without the need for moving parts. The technology is used today in niche markets for low level electricity production and has been proposed as a scalable means for capturing large scale energy from waste heat streams. The choice of geometry of the thermoelements and conductors is critical to the successful implementation of a waste heat recovery system in order to manage losses due to Joule heating and diffusive heat flows. This paper describes a simulation study to define the performance impact of different aspect ratios for the active thermoelements and the electrical interconnect. The use of a finite element model that incorporates the intercoupled heat and electrical energy flows highlights some of the issues impacting scalability.IntroductionThermoelectric phenomena arise out of the intercoupled electrical and thermal currents in a material. A two-element thermoelectric generator is depicted in Figure 1. It is constructed by connecting an N-type thermoelement and a P-type thermoelement in electrical series, with both elements in thermal parallel between a heat source and a heat sink. The electrical series connection is made by attaching conductors as shown. Ideally, these series connection elements will be both good thermal conductors and good electrical conductors.The two element generator in Figure 1 is disposed between two thermal reservoirs: the heat source, which furnishes heat energy; and the heat sink, which absorbs heat energy. Heat energy flux Q, flows from the heat source to the heat sink, driven by the temperature difference between the source and the sink. As depicted in Figure 1, when a resistive load, R, is attached, electrical current, I, may be extracted from the thermoelectric generator and furnished to the load. The N-type and P-type thermoelements, are the active portions that do the actual conversion of heat energy to electrical energy. Although thermoelements may be built using conductors such as bismuth and antimony, higher efficiency thermoelectrics are built using heavily doped semiconductors. Thermoelectric devices are generally formed by connecting many pairs (couples) of N and P type thermoelements in electrical series and in thermal parallel. A commercially available module having 127 couples (254 elements) is shown in Figure 2."

Jan 1, 2011

By Haotian Xue

A new process to extracted antimony directly from stibnite concentrate by reductive sulfur-fixation smelting in sodium molten salt has been presented. The influences of sodium salt content and composition, ferric oxide addition, temperature and time was investigated, respectively. The optimum conditions was determined as follows: W????: ??concentrate=40%, W??alt: ????concentrate =88.75%, WFe2O3 :Wconcentrate =55.13%, W??aCl: ????alt=40%, 1123K, 1h. Under above-mentioned optimum conditions, the average direct recovery ratio of antimony can reach 91.48%, and the main chemical composition of obtained crude antimony is Sb 94.31%, Fe 4.436%, Pb 0.502%, Au 0.0236%. In comparison to traditional antimony pyrometallurgical process, the smelting temperature of present process is reduced from 1423~1473K to 1123~1173K. During the smelting operation, SO2 emision can be avoided completely due to sulfur-fixation as FeS. Furthermore , S0 can be obtained when the molten slag is handled by water leaching with conditions of 323K, L/S=5/1, 2h.

Jan 1, 2014

By M. Kobashi, T. Choh, N. Kanetake

"A new processing route, which enables the cost-effective and energy- saving fabrication of metal matrix composites, have been proposed. The pressureless infiltration of the reactive powder blend with molten aluminum was investigated in this work. The molten aluminum infiltrated into the [Ti + C] powder blend spontaneously, whereas the spontaneous infiltration into the TIC powder phase did not occur under the same experimental condition. The processing time was shortened and· the processing temperature was .lowered by adding the aluminum powder in the [Ti + C] powder. The differential thermal analysis revealed that the aluminum powder in the powder blend melted at 933K and then ignited the reaction between titanium and ·carbon. However there was an .optimum additional amount of aluminum in the powder blend. The TiC formed in situ had three-dimensionally continuous morphologyIntroductionThe squeeze casting process has been used as one of the processing routes for aluminum matrix composites. [1, 2]. Non-reactive metal-ceramic systems have been, generally, used in this technique in order to prevent the degradation of the ceramic phase. Materials obtained by this process basically consist of a continuous metal matrix and discontinuously dispersed ceramic particles. Reactive systems have begun to be introduced into the infiltration process· recently [3A]. Since the ceramics are synthesized in-situ, this process can provide a continuous ceramic matrix [5]. This is one of the outstanding features of this technique in that a bulk ceramic-can be synthesized at relatively lower temperatures in a short time. Another advantage is that the highly reactive combination of a ceramic with a molten metal is in many cases wettable [6], which enables a spontaneous infiltration."

Jan 1, 2000

By Xiaolong Lin, Yuanbo Zhang, Jiann-Yang Hwang, Guanghui Li, Jiaxing Yan, Zhiwei Peng, Tao Jiang

Electric arc furnace (EAF) dust is an important secondary resource that should be recycled to enhance its considerable economic value and potential environmental benefit. In this study, a low-zinc EAF dust was characterized by various techniques, including chemical titration, X-ray diffraction, granulometric analysis, scanning electron microscopy and thermogravimetry. It is shown that the dust contains 2.08 wt% Zn, 23.16 wt% Fe and 19.84 wt% Ca, accompanying small amounts of Cr, Pb, etc. Magnetite, calcium ferrite and zinc ferrite are the main phase constituents. The majority (90%) of particles have size less than 137.862 μm. According to these characteristics, it is expected that the use of microwave energy for intensification of the reduction of EAF dust in the presence of biochar will succeed in the dust recycling by promoting the processing efficiency with elimination of secondary hazardous pollutants.

Mar 1, 2017

By Ko-ichiro Ohno

It is recently recognized that the iron reduction and melting as well as the slag separation of a composite of granular iron ore and coal are completed in a very short period of about IO minutes when the composite is rapidly heated up to approximately 1673K. These phenomena are expected to be applied to a new iron-making process. The mechanism of iron ore reduction and iron-slag separation during rapid heating has not yet been revealed and the fundamental research has just started. Carburization of the reduced iron is regarded as one of the most important steps in this process. In the present work, the composite was prepared from four kinds of coal or graphite as a carbon source and electrolytic iron powder as a completely reduced iron ore. The temperature at which the liquid formation and iron carburization occurred was monitored. Direct observation of smelting reduction behavior was made by a confocal laser-scanning microscope combined with the infrared image-heating furnace to clarify the effect of molten ash on iron carburization. It was found that the meltdown temperature of composite became lower as the melting temperature of coal ash decreased. From the observed result, it was presumed that the liquid slag would act as an important media for the carbon transfer from coal to iron. The carburization mechanism during the smelting reduction was estimated as follows. When slag containing iron oxide melted down and contacted carbon, iron oxide in the slag was reduced and the formation of the metallic iron particle as well as the its carburization occurred simultaneously at the slag-carbon interface. Carburized iron particle was carried from slag- carbon to slag-iron interfaces due to the slag convection flow caused by the difference of the interfacial tension between the carbon-slag and iron-slag interfaces. Carburization of reduced iron could proceed with a repeat of the above-mentioned process.

Jan 1, 2003

By Peijia Lin

Wheat straw was chemically modified by alkaline treatment followed by succinylation and sodium carbonate treatment for the use of cadmium and nickel adsorbent. The adsorption efficiency was calculated in different conditions. The experimental parameters were solution pH, adsorbent dosage, contact time and initial metal concentrations. The biosorbent was analysed by FTIR (Fourier- Transform Infrared Spectroscopy) to investigate the changes of surface functional group. The maximum adsorption percentages of cadmium (>99%) and nickel (>98%) were achieved using 5 g/L adsorbent with 50 mg/L initial metal concentrations. The adsorption kinetic study showed that the reaction was pseudo-second order kinetics and the adsorption isotherm was well fit by the Langmuir adsorption model. The dynamic column study indicates that modified adsorbent has a better adsorption capacity towards cadmium than nickel.

By Stuart D. Miller, Clayton L. Rumble

"A field net acid generation (NAG) test procedure has been utilized on-site to identify, classify and map potentially acid forming overburden at the PT Kaltim Prima Coal (K.PC) mining operation situated in the tropical equatorial region of East Kalimantan, Indonesia. The field procedure involves routine use of a calibrated, site specific NAG test (rapid oxidation test using hydrogen peroxide) which has a tum-around time of less than 24 hours and requires minimal sample preparation. It is used on geological drill-hole samples, for forward planning and overburden management; blast-hole samples, for day-to-day operational control and overburden scheduling; and final dump surface samples, for verification testing. This operational monitoring program has been in use at KPC for the past four years.Calibration and implementation of the field procedure has involved validating the NAG test using conventional acid-base accounting techniques, producing an overburden geochemical classification scheme, optimizing laboratory and sample preparation procedures, and ongoing quality management. This paper presents background theory and practical application in a case study format."

Jan 1, 1999

By Marcelo B. Mourão

An experimental investigation was carried out to -study the rates of reduction of pellets containing iron oxides by carbon dissolved in liquid iron, at temperatures ranging from 1720 K to 1973 K. Several different pellet types were employed; the materials used in the pellet's manufacture were pure hematite, two kinds of commercial iron ores, and mixtures hematite/silica and hematite/lime: Reaction times were determined employing the constant volume pressure increase technique (CVPI). It has been observed that the reaction rate increases as the temperature and the pellet's specific surface area increases. The reaction rate is also affected by the oxide type: pellets made from commercial ores or from mixtures hematite/silica or hematite/lime show reaction rates lower than those made from pure hematite.

Jan 1, 1996

By Kazuyoshi Shimakage, Shinji Hirai, Kenji Wada

"An amorphous zirconium oxide coating was prepared by the sol-gel process using zirconium tetra-n-butoxide on the surface of aluminum to improve the corrosion resistance to salt, acid and alkaline attacks. The coating films formed on the smooth aluminum substrates under UV-irradiation indicated an excellent corrosion resistance for salt, acid and alkaline attack tests. For example, the corroded area of coating film in salt attack test for 3600ks in the order of sol-gel coating· film< chromate film <boehmite film, and the sol-gel coating film had the best corrosion resistance. The coating film prepared on the coarse aluminum substrate by a boiling treatment after heat treatment at 573K also had greater corrosion resistance, and a water-avid surface appeared a contact angle of approximately 3°.IntroductionAs given in a previous paper1; a composite film consisting of a porous layer of anodically grown aluminum oxide filled with amorphous zirconium oxide and an amorphous zirconium oxide coating layer deposited thereon via the sol-gel process utilizing the dip-coating technique, was prepared to improve the alkaline corrosion resistance of aluminum. The alkaline corrosion resistance of these composite films was increased in the range of 24 to 50 times those of conventional anodic oxide films anodized in sulfuric acid. As a result, it was proved that heat treatment at 573K after dip-coating was an important process to .remove organic component from gel film and to accelerate the densification of coating layer. Furthermore, the effect of ultraviolet (UV) irradiation at ambient temperature on the densification of coating layer was also examined to lower the heat-treatment temperature2.Then, a sol-gel film prepared by UV irradiation at ambient temperature indicated that alkaline corrosion resistance of aluminum was superior in the range of 2.4 times to 2. 6 times that of the conventional composite film heated at 573K."

Jan 1, 2000

By T. -M. Guo, M. J. Braun

"This paper presents an experimental and numerical study of melt flow near the solid-liquid interface and its effect on the interface curvature in a horizontal unidirectional solidification system with succinonitrile. Melt flow is introduced by increasing the ampoule channel thickness. Visualization techniques are employed to observe the flow field and the solid-liquid interface curvature. A numerical model is also developed to simulate the heat transfer, melt flow and phase change in the system. Quantitative information on the flow and temperature fields is generated. A good agreement is achieved between the experimental observations and model predictions. The results could be used for the study of the effect of the melt flow on interface morphology during solidification.IntroductionClassic unidirectional solidification experiments of transparent alloys are conducted with thin film samples sandwiched between two glass slides to investigate the development of interface morphology during solidification [1]. Samples with small channel thickness are usually used to suppress any melt flow due to natural convection and solidification in the channel would then be in the diffusive regime so that the solidification theory can be significantly simplified [2, 3]. Effects of melt flow, in particular due to natural convection, on solidification have also been studied extensively in those systems with large geometrical dimensions [4-6]. These studies indicate a strong effect of the melt flow on interface curvature during solidification [5, 6]. Only limited efforts were made to address the effect of the melt flow on interface morphology in horizontal unidirectional solidification, in particular for the cases when the channel thickness is not thin enough to suppress completely the natural convection [7]."

Jan 1, 2004

By P. A. Davidson

"We discuss the influence of a static magnetic field on jets, vortices and turbulence. This is particularly relevant to D.C. braking in slab casting. Our main conclusion is that, typically, the magnetic field destroys mechanical energy, via joule dissipation, but is unable to destroy momentum. Rather, it continually rearranges the momentum in such a way that the energy falls.IntroductionIt is well-known that a static magnetic field can suppress motion of a liquid metal. That is to say, movement of the liquid across the magnetic field lines induces a current. This leads to Joule dissipation and the resultant rise in thermal energy is accompanied by a corresponding fall in kinetic energy.This phenomenon has been exploited in a range of metallurgical processes. For example, in the continuous casting of large steel slabs, an intense, static magnetic field is commonly used to suppress motion within the mould. The objective is to keep the free surface of the liquid quiescent, thus avoiding the entrainment of surface debris. In other solidification processes, such as techniques for growing semi-conductor crystals, it is widely believed that natural convection has a detrimental effect on the metallurgical structure of the solid. Again, the imposition of a static magnetic field is seen as one means of suppressing these unwanted motions. Finally, magnetic damping is used in the laboratory measurements of chemical and thermal diffusivities, particularly where solutal or thermal buoyancy can disrupt the measurement technique.In this paper we shall look at the damping of jets, vortices and turbulence. Our aim is to present a unified theoretical framework from which the many published studies may be viewed."

Jan 1, 1999

By A. K. Kyllo, G. G. Richards

"The formation and control of accretions is an important aspect of process operation for gas injection. The nature of the accretion formed can have a considerable effect on a process, especially on the life of the lance or the refractories in the tuyere region. There are three basic shapes of accretion formed on tuyeres; pipes, hemispheres and hollow-cored hemispheres. However, there are wide variations within these shapes. Generally, the type of accretion formed will depend on the injector design, certain operating parameters and the physical properties of the bath materials. This paper seeks to collect the results of previous and current physical and mathematical modelling together with data gathered from operating furnaces, to obtain a better understanding of the effects of process design and operating variables on accretion formation.IntroductionAn important consideration in the design of a gas injection process is the possible freezing of the bath either around the tuyere or on the lance. With proper design, freezing may be controlled to provide protection of the lance or refractory, and to avoid blockage. Improper design may lead to tuyere blockage and significant refractory or lance erosion. In view of this, a good understanding of the heat transfer in the injection region is essential.While tuyere blockage has been a persistent problem since the inception of submerged gas injection processes, the problem of accretion formation was not studied in detail until the development of the shrouded tuyere by Savard and Lee. A number of studies relating to accretion formation have been carried out since then, but there is still little information available relating the nature of the accretion formed to the design of the injection system.The build up of materials on lances is a similar problem, and may also be either beneficial or detrimental, depending on circumstances. Unfortunately, there is even less information available regarding build up on lances than there is relating to tuyere accretions. While the form of build up on lances is generally a simple coating of the lance, accretions on tuyeres tend to be more complex. Tuyere accretions tend to occur in one of three basic forms: pipe, hemispherical and hollow-cored hemispherical (Figure 1). However, there appears to be a considerable variation within these forms."

Jan 1, 1996

By R. R. Beebe

"Laboratory and pilot-scale tests are almost invariably required before metallurgical development can proceed. Difficulties with sampling, as well as with classical chemical and physical scaleups, are normally anticipated and relatively well-understood, but more subjective factors also come into play, including misunderstandings of the operating scheme chosen, wrong ""lessons"" learned from similar operations, failures to handle data appropriately, and even arbitrary intervention by management. The paper examines some of these subjective factors and suggests ways to guard against them. Several anecdotal case studies are used as examples, including when and where to heap leach or to mill specific types of gold ore.When the Romans first exploited the gold-rich gossans at Rio Tinto, they were guided by analyses and tests that delineated the ore deposits, identified the richer portions, and measured the gold recoveries achieved. There is little evidence, however, to suggest that test data were used to develop improved methods of metallurgical extraction. Indeed, it is likely that ores too difficult to treat were simply passed by, at least until improvements in full-scale operations could deal with them. For example, it is not difficult to imagine that an early metallurgist might test a tin ore by placing some in a fire; a smallscale emulation of the method actually used in practice."

Jan 1, 1997

By S. I. Sobol

Completeness of cobalt recovery from slag requires decomposition of maggemite and non - ferrous metal desorption with polymerized silicon-acid. Cobalt losses are reduced in leaching tai1s up to 200 g/t of iron.

Jan 1, 1993