Search Documents

By Adegbenjo Adewale Oladapo, Ibitoye Simeon Ademola, Ladiipo Olufemi Akinbiyi, Adegbola Adekunle Amos, Adeboje Taiwo Bode, Raji Fatai Olasunkanmi

The combined effects of the addition of Silicon (Si) as alloying element and low temperature annealing on the tensile properties of 70/30 brass with Nickel (Ni) and Iron (Fe) contaminants is investigated in this paper. Melts of cartridge brass were made to which 0, 0.5, 1, 2, 3 and 4 wt % of Si was added. These were sand cast into rods of 600 mm by 10 mm diameter and were thereafter machined into standard tensile test samples. Some of these samples were annealed in a muffle furnace at temperatures of 250, 300, 350, 400 and 450 oC respectively and the others were used as control. Subsequently, all the heat treated and non heat treated samples were subjected to tensile tests on a Hounsfield Extensometer and the load – extension plots retrieved were analyzed. Microstructural characterizations of the samples were carried out using Accu-Scope Optical Microscope. The results showed that cartridge brasses subjected to alloying and annealing treatments had improved tensile and yield strengths. However, the tensile properties were increased and maintained within acceptable limits at stress relieve annealing temperatures.

Jan 1, 2015

By Yotamu Stephen Rainford Hara, Animesh Jha

The investigation focuses on a low temperature recovery of Cu and Co from a 40 wt% SiO2-(30 wt%Fe,6 wt%Al)2O3-10wt% CaO-7wt%CuO-7wt%CoO slag over a temperature range of 1173K to 1323K. The alloy phases containing Cu-Co and Fe-Co alloy formed via the carbothermic reduction of oxides: MO + C = M + CO(g), where M represents metallic copper, cobalt or iron. In the direct reduction of oxides, the recovery of metallic phase was well below 90% at 1323K, due to the kinetic barrier which was analysed and attributed to oxygen and metal-ion transport in the slag. This barrier was overcome by adding CaSO4 and carbon, which yields a matte (MS) phase via MO + CaSO4 + 4C = MS + CaO + 4CO reaction. Lime thus produced in situ participates in metal oxide/metal sulphide reduction reactions, which are analysed with the help of X-ray powder diffraction, scanning electron microscopy, and thermogravimetric analysis.

Jan 1, 2014

By Nathália M. Campelo, Alexandre P. Umpierre, Fabricio Machado

"The present work illustrates the reuse of macoporous anion exchange resins (employed for decolorization of solutions of organic substances such as sugar syrup and fruit juice concentrates in the soft-drink and beverages industries), based on crosslinked styrene-divinyl benzene copolymer (Sty-DVB) to the production of polymeric materials. Micro-sized particles of polystyrene and poly(styrene-ethyl acrylate) were obtained by mass-suspension sequential polymerization process. The proposed experimental technique was able to perform proper dispersion of the Sty-DVB in the thermoplastic matrix of polystyrene. The final material showed good thermal stability, showing degradation profile similar to that observed for the pure polystyrene. It was also noticed that polymer particles with spherical morphology can be obtained. In addition, the incorporation of ethyl acrylate monomer into the polystyrene chains minimizes the undesirable effect of fracture in polymeric particles, improving the mechanical and end-use properties of the final polymeric composite.IntroductionIn face of the industrial development, the development of techniques that are safer and less aggressive to the environment has become one of the main challenges in the industrial field. In this scenario, processes more efficient in terms of energy and raw materials can be regarded as an important requirement to minimize the production of waste. The reuse of waste becomes an attractive alternative for most industries engaged with sustainable and economic development.In this context, both the primary and the secondary mechanical recycling are potentially attractive because they allow for reuse of polymeric waste (post-industrial or post-consumer) as a source of raw material in the supply chain by using traditional methods of processing, so that the final materials can exhibit characteristics similar or superior to those observed in the virgins polymeric materials, considered as a starting product in the process of reuse of plastics [1-3]."

Jan 1, 2012

By F. E. Brinckman, G. J. Olson, D. Johnsonbaugh, T. K. Trout

"Microbiological metal recovery is an emerging technology likely to play an increasing role in commercial ore leaching, metal removal from process and waste streams, and perhaps ultimately in processing to yield metal products in specified forms or oxidation states. We are studying the potential for using microorganisms for the recovery of elements important to emerging materials technologies and for which domestic supplies are limited and/or low grade. Examples to be discussed include the bioaccumulation of yttrium and gallium. These elements are important in the production of new superconductor and semiconductor materials. However, limited domestic reserves and technologies for their recovery may cause supply problems. Microbiological processes may offer new techniques for recovery of these and other strategic elements.IntroductionMicroorganisms in ore leachingMicroorganisms assist in the commercial leaching of copper and uranium from low grade ores (1,2) and recently have been shown to have immediate commercial potential for the pretreatment of refractory gold ores to increase the gold-cyanide recovery yield (3). Copper bioleaching is the best known example of biotechnology applied to metal recovery. Copper can be recovered by commercial leaching of huge piles or dumps of low grade sulfidic ores and waste materials, which are not otherwise processable. Microbial activity in the leach dump environment oxidizes metal sulfides to soluble metal sulfates:"

Jan 1, 1988

By P. L. Sibrell

The U.S. Bureau of Mines has tested cyanide leaching for recovery of palladium (Pd) from spent petroleum processing catalysts. Three different catalyst samples were supplied by a spent-catalyst processor. These catalysts consisted of a zeolite base and contained 0.4 to 0.7 pct Pd. During alkaline cyanide leaching, the catalysts exhibited ion-exchange properties due to their zeolite matrices. Hydrogen ions were released from the zeolite in exchange for sodium ions in solution, resulting in a significant decrease in solution pH. This could present a safety hazard because of the potential for release of toxic hydrogen cyanide gas. A pretreatment .step where the catalysts were contacted with a 1.0M sodium hydroxide solution was found to prevent the pH shift from occurring. Following the sodium hydroxide pretreatment, two stages of leaching at 160 °C with solution containing 1 pct sodium cyanide and 0.1M sodium hydroxide gave at least 75 and up to 95 pct Pd recovery. The Pd was quantitatively recovered from the leach solution by thermal decomposition in an autoclave at 250 °C for 1 h. The Pd content of the precipitate was over 50 pct. Thermal decomposition also decreased the total cyanide content of the barren solution to less than 0.2 mg/L. The catalyst leach residues passed the Federal Toxicity Characteristic Leaching Procedure and the California Waste Extraction Test, indicating that landfill disposal of the leach residues would be acceptable.

Jan 1, 1995

By A. Navarra

Within conventional copper and nickel-copper sulfide smelters, ladles of molten matte are fed into converters. These converters blast oxygen-enriched air into the matte, thereby eliminating iron and sulfur. The converting reactions are exothermic and, indeed, the converter heat balance is often a limiting consideration on the smelter throughput. If a portion of the matte were fed in solidified (granulated) form, this would support higher oxygen enrichment, and lower volumes of converter offgas, allowing higher throughput. This approach is not applied in conventional smelters, partly because of the copious amounts of water that must be evaporated in typical granulators, as in the Kennecott-Outotec process. The current paper recalls a waterless matte granulator that had been pioneered in the 1990’s, and is applicable to conventional smelters. A mathematical formulation is presented that can be used in the context of simulation-based optimization, to estimate the size and impact of waterless matte granulation.

By M. Demuth, B. Holleis, M. Potesser, D. Spoljaric

"In 2005, Messer Group established a technology competence centre for metallurgy in Gumpoldskirchen (Austria), with the aim to develop oxygen burners which satisfy today's and upcoming standards of legislation as well as customer requirements. With the assistance of the Development Sponsorship Fund (FFF) of Austria, cooperation with the University of Leoben was agreed on. With the long term experience of the Gas-Warme-Institut ""GWI"" in Essen (Germany) and the University of Leoben, different new burners have been developed.The efficiency of industrial combustion processes can be increased in two ways (which can be seen in Figure 1 ), either by preheating the fuel and combustion air or by adding oxygen. Due to the high 79 % Nz ballast in air combustion, only low flame temperatures can be reached. This results in high heat loss in the exhaust gas, caused by the low combustion efficiency. Oxygen can be introduced into the combustion chamber using different techniques:• Oxygen fuel burners• Direct oxygen injection into the fuel air flame• Underlaying of the fuel air flame• Enrichment of the combustion airIn Figure 2, the theoretical flame temperature for the stoichiometrical combustion of natural gas is plotted as a function of oxygen enrichment. Therefore, it can be concluded that even low enrichment values produce higher flame temperatures and result in higher combustion efficiency."

Jan 1, 2012

By Jay. M. Khodadadi, Josef Štetina, František Kavicka

"With the aid of the proper original numerical model of solidification the instruction for preparation of input parameters for numerical simulation of technological processes, with change of the phase or structure, will be presented. A method of calculation analysis of influence of therrpophysical properties of materials entering the system of casting-mould-cores environment, and also of boundary conditions on the required simulation accuracy will be suggested. For the cast material, the influence of heat .conductivity, specific heat capacity, density and latent heat of phase transformation also has been analysed. For metallic or non-metallic moulding material"" the influence of the see main parameters has been analysed and, furthermore, their combination, influence of thermal conductivity, and of heat storage. The order of influence of all quoted parameters of a casting and moulding material was established. For example heat conductivity in the liquid state is on the last place. From the boundary conditions the -most important influence on the total solidification time and · on the mechanism of forming of temperature field has the ·boundary condition on the casting mould boundary, then follows the boundary condition on the level of a molten metal. The negligible influence has the boundary condition on the mould frame and on the bottom.IntroductionThe original and universal mathematical model of solidification, cooling and heating has been set up and checked, in order to be capable of analysing a one- to three-dimensional steady or unsteady temperature field of the casting-mould-environment system and, namely, of the system as a whole or its arbitrary parts, during any industrial technological process whose individual processes could be solidification, cooling, heating, refrigeration and others, in any sequence or singly. The model enables the simulation of traditional and also non-traditional technologies of casting in foundries, metallurgical plants, forging operations, heat treatment processes, etc. If solidification is not the matter, the metal part of the system need not be called the casting but a component, a block, a forging and the like."

Jan 1, 2000

By Denise Nascimento, Alice Barreto Bevitori, Felipe Perissé Duarte Lopes, Renan Carreiro, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"Natural fibers obtained from plants have increasingly been used as reinforcement of polymeric composites in engineering applications. This is the case of the fiber extracted from the piassava palm tree, a native of the southeast region of South America, which for a long time has been used in simple items like brooms and brushes. Recently it was reported that the tensile strength of the piassava fiber varied inversely with the equivalent diameter. Following that previous work, the elastic modulus and the density dependence on the diameter of stiffer piassava fibers of the Attalea fiinifera species was investigated. Precise measurements with a profile projector and Weibull analysis of the experimental results indicated that both the elastic modulus and the density of piassava fibers also follow an inverse correlation with the diameter. Scanning electron microscopy observations of the microstructure and fracture surface showed that defects and participation of microfibrils are responsible for this correlation.IntroductionIn the past decades, both the increase in the price of the petroleum and climate changes due to greenhouse gas emissions are motivating the use of renewable and low cost natural materials as a substitute for energy intensive and CO2 contributor synthetic materials [1]. A typical case is that of natural cellulose-based fibers extracted from cultivated plants in comparison to glass fibers, which are extensively used for composite reinforcement. In fact, these natural lignocellulosic fibers are increasingly being investigated [2-6] as possible reinforcements of polymeric composites, and in some cases, successfully replacing glass fiber composites in engineering applications [7]. The automobile industry has remarkable examples of lignocellulosic fiber composite substitutions [8-10]. Not only do some of these fibers display specific mechanical properties comparable to glass fibers but their composites also contribute to lower equipment wear and better finishing of molded components [6]."

Jan 1, 2012

By Gunnar Eriksson

Computer simulation has become an everyday practice in thennodynamic and materials research. Advanced thennochemical algorithms take into account heat transfer effects and salient reaction kinetics when applied for process models. In particular, the combination of mass transfer or overall reaction rates with multi-component Gibbs energy minimisation provides an effective tool for simulation of industrial thennochemical processes and processing of materials. In this work the combination of rate factors with the Gibbs energy technique was studied by using the novel program ChemSheet, which operates through Microsoft's Excel® spreadsheets. Such processes as, for example, CVD of pure silicon production, titania pigment manufacturing, vapour pressure of Mercury in amalgams (in Hg-Iamp manufacturing) and melting behaviour of low-temperature alloys have been modelled. Provided that the thennochemical data is available simulations can be performed with any thennodynamic system. The calculation can be performed as an affinity study without a particular reactor model or with a specific reactor scheme.

Jan 1, 2001

By Bogidar Mihaylov

A laboratory study was conducted on continuous precipitation of copper, cadmium, mercury and arsenic using thiourea, thioacetamide, sodium sulfide and ammonium sulfide as precipitating agents. Depending on the experimental conditions the metals precipitate with the sulfide donors at different orders and rates. These differences were employed as a basis of several techniques for continuous separation of copper and arsenic, cadmium and arsenic, mercury and copper, and copper, mercury and arsenic. The separation of the metals from industrial waste solutions was also studied. The precipitates obtained were inspected using x-ray diffraction, scanning electron microscope, atomic absorption spectrometer and plasma particle counter.

Jan 1, 1992

By Ajay K. Singh

The surface quality demands for galvanized and galvannealed steel sheets by the automotive and appliance industries have been getting increasingly stringent over the past few years. Intensive efforts by Hot-Dip-Galvanizers to meet these demands have resulted in substantial improvement to the hot dip coating process. However, elimination of zinc bath contaminants which directly affect the coated strip surface quality continues to remain a tough challenge. As part of our effort to improve the zinc bath cleanliness, Inland Steel Company has developed a test method to quantitatively measure the contaminants in incoming zinc spelters and establish a specification for incoming zinc quality. The test is currently being used for auditing the incoming zinc quality. The zinc suppliers are also using this test for quality control purposes. The purpose of this paper is to describe the test method and how it has improved the galvanizing operation at Inland.

Jan 1, 1992

By R. Togashi, T. Aichi, T. Yamada

"A new automatic material- handling system for cathode transportation has been developed. The first system went into service in August 1994 and the remains will be operational subsequently.Because of the complex cell-layout and the number of cells in each row, the critical part of this work was achieving a planned cycle time. This cycle time is determined by the power costs.The central monitoring system for machine operation was started in June 1996, using original application software based on MICROSOFT EXCEL ® on WINDOWS 95® .As a result, only one person is now required to operate both a crane and a stripping machine for one row of about 50 cells.INTRODUCTIONMainly due to the strong yen and the relatively low price of metal, the zinc refineries in Japan are being forced to reduce production costs again and again.The trend of lijima's production costs is shown in Figure 1.[1] The ratio of labor costs becomes gradually higher. Therefore it is effective to reduce the labor costs in order to reduce the production costs. In Japan, electricity cost during day time is too high to produce zinc at a reasonable cost, that is why the actual production is far from the capacity of production at a cell house. That means a plant in Japan has the disadvantage of relatively low productivity for cell house operation.Saving labor costsSome automatic cranes have been applied to save labor costs for cell house operation in the world. In consideration of the mentioned low productivity, the installation of an Automatic Cathode Transfer (ACn system for transportation of cathodes was planned without changing the present cell house and stripping machines to lower the investment costs. The ACT system must keep up with the stripping machine which is able to strip deposit zinc from a cathode sheet at the rate of 6 seconds.The fifth ACT system of seven was installed in August 1996 and the last one will be operational subsequently."

Jan 1, 1997

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

Acid mist generation is a major concern in zinc, copper and nickel electrowinning industries and there is a strong environmental drive to control its emission into the work environment. Foaming reagents are typically added to the electrolyte to alleviate this problem. In zinc electrowinning, Licorice and Saponin are examples of foaming reagents used for this purpose. In order for the foaming reagent to be effective, its foaming behavior must be determined. In this work, a test procedure was developed to study the foaming characteristics of various surfactants for use as foaming agents to control acid mist in aqueous metal electrowinning. This new test was termed as "mini-flotation test" and it was used to study the foaming behavior of a large number of reagents in an industrial zinc sulfate electrolyte under simulated zinc electrowinning conditions (gas sparging). In addition, the influence of important process parameters such as current density, electrolyte temperature, reagent addition level and sulfuric acid concentration on the foaming characteristics of the electrolyte for each surfactant were investigated. The results of this study have identified the most important factors that influence foam formation, growth and stability. This method could be used as a process control for reagent addition in the cellhouse by generating a calibration curve for the optimum electrolyte conditions.

Jan 1, 1997

By Thomas M. Harris

Cation exchange is not sufficiently selective to be used for the removal of heavy metal ions from a general industrial wastewater. However, if the metals can be converted to polyvalent anions through complexation, they may be removed both selectively and efficiently by anion exchange. This approach, referred to as chelation-assisted anion exchange (CAAE), has been examined using industrial wastewater samples contaminated with Ni2+ and Cr3+. For this particular application, the Ni2+ is complexed with 8-hydroxyquinoline-5-sulfonic acid, and the Cr3+ with sulfosalicylic acid. Removal efficiencies and adsorption isotherms for both the complexants and the complexes were determined in batch-mode tests.

Jan 1, 1994

By N. J. Rarmrez, C. Perez, J. D. Calderon, L. Lopez

"Among the thermal characterization of any material, one of the variables to know is the coefficient of thermal conductivity because this value can tell how much heat passes through the material and if the material could be used as an isolator. In order to determine this parameter is required some kind of special equipment and controlled conditions which implies high costs in the development of tests. The present paper proposes a design of a low cost measurement system in order to determine this coefficient with the lower possible error. This equipment was thought for companies or labs where they do not have the economic resources or the infrastructure (environmental controlled labs, heat flux transducers, human resources with specialized knowledge) to do this kind of tests.The system is based on ASTM C 518 - 04 [l] and integrated by two plates (one that contains a thermal resistance and which temperature is controlled by a closed loop controller and the other one with a route of water flow). The thermal resistance is actuated by a relay and a supervisor system checks the total time the relay is on in order to determine the effective power applied to the system. The contact faces of the plates contain a group of temperature sensors connected to a data acquisition system that process and record the temperature in each measurement point.With the power applied to the system, the measurement of temperatures and a process of calibration is possible to determine the coefficient of thermal conductivity. IntroductionWithin the thermal characterization of a material of known variables is the coefficient of heat transfer, since this value can know the amount of heat the material is capable of transferring or isolating. To determine this ratio requires specialized equipment and controlled conditions, which implies high costs in the development of a test. This article proposes a design of a low cost machine to allow closer this coefficient with the least possible error. This equipment was done thinking about companies that do not have the infrastructure (laboratories, controlled environment, heat flux sensors, human resources expertise) and financial resources to conduct these tests."

Jan 1, 2011

By David Cocke

Study of surface and subsurface interfacial chemistry of metallic and similar systems has its enormous technological importance. Copper, for example, is a common component of many alloys and bulk amorphous systems. It is being increasingly studied today because of its use for electronic interconnect systems where processing is done below 200 ºC. Since several types of copper oxides exist, and the degree of their formation is dependent on temperature, perhaps characterization by EDS-SEM depth profiling and EIS might delineate one type of oxide from another. In this paper, we described our work on transformation of copper oxides with temperature ranging from 70 to 350 °C and their characterization by SEM, EDS, and XRD. We also showed the use of the phase angle portion of the impedance as a means to identify the predominant structure and the transition through Cu3O2 between the predominant stable CuO and Cu2O.

Jan 1, 2009

By Nobuhiro Kuriyama

Electrochemical activation behavior of an AB2-Laves-phase type hydrogen storage alloy, Zr0,9Ti0.lNi1.lCo0.1Mn0.6V0.2 was studied to make clear activation process of pellet-type metal hydride electrodes. An alkaline treatment of the electrodes with heated alkaline solution gave alloy surface enriched with nickel, and the treated electrode was more easily activated. The treated electrode desorbed more hydrogen during the first charge-discharge cycle, and was activated without induction period. A cross sectional view of the activated electrode showed finer pulverization of alloy particles than the annealed alloy, and impedance spectroscopy indicated larger surface area of the electrode using the as-cast alloy. Since the as-cast alloy contains inhomogeneities, multi-phase microstructure and stress in the particle, the finer pulverization of alloy particles with hydrogenation are considered to increase surface area in an earlier cycle in the case of the as-cast alloy, which leads larger reaction area and faster activation of the as-cast alloy electrode.

Jan 1, 2002

By R. W. Bartlett

The extensive central Idaho black sand placer deposits are a potential source of rare earth elements, particularly the heavy rare earth elements that are not prevalent in commercial bastnasite deposits. These placers derive from the Idaho batholith. The geology, occurrence, and extent of these deposits are reviewed and the diverse mineral assemblages and complex mineral chemical compositions of these sands are described. Niobium, yttrium and thorium are also present in significant concentrations. The results of prior mining practice, including concentration and separation of the heavy minerals are reviewed. Technical approaches to extraction of rare earths from Idaho black sand concentrates are discussed.

Jan 1, 1992

By W. Dresler

Design details of a 100 kVA DC electric-arc reduction furnace are described. The furnace is equipped with a 610 mm (24 inch) diameter graphite crucible hearth. A 76 mm (3 inch) diameter top graphite electrode is used as a cathode. The current passes through the bottom of the crucible and is carried to a bottom plate (the anode) by conductive magnesia carbon bricks. The furnace can be operated up to a maximum of 120 V, 1800 A, and presently 100 kW. The start-up operating experiences and metallurgical results of one reduction test with a Montana chromite containing 38% Cr2O3 are discussed.

Jan 1, 1994