Search Documents

By Yuri Hovanski, Jingyi Zhang, David P. Field, Piyush Upadhyay

Friction stir welding has gained wide interest in industry and drawn large research attention due to its high level of automation and superior joint performance. In this study we further expand the welding parameters to be of magnitudes higher than those previously reported to lower the cost and enable high volume joint production. Sound butt-joints were produced with aluminum alloy 6111-T4 blanks with welding speeds up to 6000 mm/min. Tensile tests of the joint pieces show >97% joint efficiency in terms of ultimate tensile strength. The T4 natural aging and grain refinement is found to contribute to the superior joint properties. Electron backscatter diffraction (EBSD) analysis is used to qualitatively study the local shear texture inside the nugget zones of the welds. The shear texture result is a good indicator of the material flow directions in the nugget zones. The flow directions behind the rotation tool are found to be flattened towards the top surface of the workpiece when the welding speed is increased, suggesting intense material mixing and transportation along the longitudinal welding direction (WD).

Mar 1, 2018

By Stephen Chryssoulis, Stamen Dimov

Detection and quantification of precious metals (Au, Pd, Pt, and Rh) in spinels and silicate minerals is important for establishing the maximum attainable recovery by sulphide flotation. To achieve this goal subpart per billion (ppb) detection limits are required plus the ability to quantify results. Existing quantitative microbeam techniques (EPMA, PIXE, SIMS, TOFLIMS) have limits of detection in the O. l-200ppm range. Time-of-flight resonance ionization mass spectrometry (TOF-RIMS) is a microbeam analytical technique that allows for the identification and quantification of atomic species in very small quantities. It utilizes a tunable laser source for resonant excitation and ionization of a particular element of interest and has some unique features: elemental selectivity, linear response over a large dynamic range and very high sensitivity. The analysis consist of three steps: (i) the solid sample is vaporized by laser ablation to form a plume containing neutral atoms, (ii) the neutral atoms of a specific atomic element in the plume are resonantly excited and ionized by another tunable laser, and finally (iii) the ions created are mass analyzed in a time-of-flight mass spectrometer. A TOF-RIMS mass spectrometer was developed at AMTEL for trace element analysis of Au, Pd, and Rh in minerals. The spectrometer was calibrated using homogeneous CANMET and NIST reference samples covering three orders of magnitude in concentration. Attained minimum detection limits (MDL=2cr of the background) are in the low ppb range.

Jan 1, 1999

By Xueqin Li, Xuewei Lv, Wenchao He, Jie Qiu, Jie Dang

Iron powders are mainly produced by Hoganas process and water atomization process, while both of which have the disadvantages of energy consumption. To obtain iron powders with higher particle sphericity, more uniform particle size distribution and higher proportion of total iron (TFe), a novel method considering of energy conservation was developed in this paper. The hot metal was transformed into granules with air cooling in a rotary disc atomizer, iron powder particles and hot off-gas were collected respectively. It was found that the property of the obtained iron powders was mainly controlled by the flow rate of the hot metal, the diameter of the rotary disc and the rotary speed and the heat of off-gas has a high level of value as well.

Mar 1, 2017

Roasting treatments were investigated to remove arsenic from a nickel concentrate. The main arsenic minerals and their proportions in the concentrate were niccolite (NiAs)-50%, gersdorffite (NiAsS)-40% and arsenopyrite (FeAsS)-10%. Thermal analysis showed that gersdorffite and niccolite began decomposing when heated above 640 and 830°C respectively. The maximum roasting temperature was limited by agglomeration of the concentrate above 900°C. A small vibrated bed reactor was used to investigate the effects of temperature and gas flowrate, the latter to sweep away evolved arsenic. At 900°C, 24% of the original arsenic remained in the concentrate. SEM examination of the calcine showed that the residual arsenic was associated with the calcium in the gangue minerals. Additions of sulphur (either as elemental sulphur or from pyrite) facilitated the decomposition of the arsenic-containing minerals, decreased reaction with calcium in the gangue and produced calcine containing 4-6% of the original arsenic. Treatment with chlorine during roasting was effective in reducing the arsenic content to similar levels. Generation of chlorine in the bed by sulphation of CaC12 also produced encouraging results. Arsenic, Nickel Concentrate, Roasting, Chlorine, Sulphur, Gersdorffite, Niccolite

Jan 1, 2005

By Caisa Samuelsson

Experimental studies in laboratory-scale equipment have been carried out to study the vaporisation from dust generated during the copper converting process. In the present work the vaporisation of Zn, Pb, As, Sb, and Bi from a dust collected in the electrostatic precipitator after the copper converter were studied. The results show that Pb, Bi and As were vaporised to a high degree from the dust at a temperature above 900°C in a gas containing N2, SO2 and a small amount of H2. The vaporisation was high for these elements also in a gas containing N2, SO2 and 02 at temperatures above 1120°C. In an earlier study, thermodynamic calculations showed that it is possible to selectively condense metals at high temperature' in a gas atmosphere generated during a copper converting process. The present study was carried out to verify the thermodynamic model. The results indicate that it should be possible for a selective condensation of Zn at high temperature. The temperature required for a selective condensation of Zn is dependent upon the gas atmosphere, e.g., the oxygen potential.

Jan 1, 1998

By E. B. Freidina

We have investigated a new electrochemical process for preparing lead-calcium alloys. Calcium metal, reduced fiom a molten chloride mixture, forms an alloy with liquid lead cathode. The addition of calcium carbonate to conventional CaC12-NaCl electrolyte enables us to avoid chlorine production on the anode and replace it with oxygen and carbon dioxide. The ternary system CaClz-NaC1-CaCO3 has a range of melt compositions, where the electrolysis can be held below 650°C. In order to prevent the side reaction of carbon deposition on the cathode we have separated the anolyte from the catholyte with alumina diaphragm. The factors, which affect the level of impurities and the current efficiency of the process, are discussed.

Jan 1, 1999

By Chao Zhang, Kexin Jiao, Yi Qian, Jianliang Zhang

Now low-grade iron ore were widely used. However, one prominent problem is that the content of trace elements is higher than that in high quality iron ore. For the requirement of the content of Mn, Cr, Ni, Cu, and Ti in hot-rolled steel sheet and strip, the upper limits of these elements in sinter will be studied in this paper. Using the activity model of aggregation of electronic phased slag composition, the distribution ratio of each element in converter is analyzed and the content of each element in hot metal is calculated. Furthermore, through the thermodynamics method, the distribution ratio of each element in BF is analyzed and the content of each element in raw material is calculated. The upper limits of Mn, Cr, Ni, Cu, and Ti in sinter can be determined by calculating, the values are as follows: Mn 0.767%; Cr 0.552%; Ni 0.055%; Cu 0.159%; Ti 0.108%.

Jan 1, 2015

By D. R. Spink

A partial desulfurization roasting (PDR) technique has been developed for use on zinc concentrates whereby the sulfide sulfur associated with the iron content is selectively removed over a very short residence ?time in the roaster. The resulting PDR product is then leached for the selective removal of the iron. The resulting leach restdite is an upgraded zinc sulfide concentrate which has a very low iron content. The up-graded zinc concentrate can be subjected to a conventional dead roast without formation of deleterious zinc ferrite so that hot acid leaching and jarosite (or other) iron precipitation steps are obviated. Examples are presented for the treatment of three very different types of zinc concentrates.

Jan 1, 1990

By Don Eby

The application of electric arc furnace smelting of lead, antimony, and tin bearing slag from a reverberatory furnace will be discussed. The selection procedure for the 4.0 MVA electric arc furnace in Indianapolis, Indiana is presented. The design criteria for the transformer, electrodes, refractories and associated equipment is presented. The operation of the furnace including chaJ:9ing, bullion tapping, slag tapping, ventilation, slag composition, metal recoveries, and toxic leach results of thra.1 away slag are discussed. Flow charts and the equipment specifications are given.

Jan 1, 1990

By Yasumasa Hattori

An extensive study including fluid dynamic calculations, cold model tests, pilot plant tests as well as measurements in a commercial flash furnace was carried out in order to develop a new Sumitomo flash smelting concentrate burner. The pressure measurements in the commercial burner indicated that the premixing of the concentrate and reaction air in a burner was insufficient. Pilot plant tests showed that enhancement of the premixing of the concentrate and reaction air is very effective for improving the burner performance. Using the additional pressure drop of the reaction air as an indicator of the premixing, a new type Sumitomo premixed concentrate burner was developed.

Jan 1, 2003

By K. A. Brunk

Newmont's research, operations, history and experience with pre-treatment of preg-robbing carbonaceous ores are described, with emphasis on the chemistry, physics and kinetics of chlorine treatment. Present operations, control strategy and projected changes are also described, including a summary of the adsorption of chlorine into pulps and off-gas scrubbing. Conditions of chlorination have been optimized by the use of Eh-pH diagrams of the gold-chlorine-water system, and have resulted in significant increases in gold recoveries and decreases in chlorine consumptions.

Jan 1, 1987

By A. K. Kyllo

A study has been carried out on the dusts from Hudson Bay Mining and Smelting's Flin Flon copper smelter. The aim of the work was to determine the mechanisms of dust formation and the deportment of the various constituents. The work concentrated on the copper converters, but the electrostatic precipitators and baghouse also clean the reverberatory furnace off gas, so some mixing will have occurred. The dust composition was found to vary with distance from the furnace, and to be made up of three major components: solidified droplets, unreacted flux, and condensed particles. The solidified droplets were formed from material ejected from the converter during blowing, while the flux was blown out of the converters immediately after charging. The condensed particles contained the majority of the lead and zinc, as well as the volatile impurities. There was also a significant soluble content of the dusts, increasing with distance from the furnace. The condensed material may be separated from the remainder by a simple washing and sizing technique.

Jan 1, 1996

By He Jing, Wang Changhong, Chen Yongming, Wu Yanzeng, Yang Xiyun, Tang Chaobo, Yang Shenghai

Pitting of Hf in Et4NBr t-butanol and acetonitrile (ACN) solutions was studied by means of cyclic voltammetry, potentiodynamic anodic polarization,galvanostatic, potentiostatic and impedance techniques. The potentiodynamic anodic polarization curves did not exhibit an active dissolution region near corrosion potential due to the presence of an oxide film on the electrode surface, which was followed by pitting corrosion resulting from the passivity breakdown by the aggressive attack of bromide (Br−) ion. The pitting potential (Epit) increased with increasing potential scanning rate but decreased with increasing temperature and Br− concentration. Cyclic voltammetry and galvanostatic measurements allowed the pitting potential (Epit) and the repassivation potential (Ep) to be determined. Analysis of the potential/time transients revealed that the applied anodic current density had a significant influence on the values of Epit. On the other hand, the Ep values were independent on the applied current density. The current/time transients indicated that the incubation time (ti) for passivity breakdown decreased slightly with increasing potential and solution temperature. The impedance spectra showed that the resistance of passive layer decreased with increasing potential.

Mar 1, 2017

By Fang-Qui Zu

Understanding the nature of liquid structures and properties remains an open problem for many fundamental and applied fields such as materials sciences and processing. And as well known, there is no other defined phase line above liquidus (TL ) in phase diagrams of ordinary binary systems. However, via different experimental resorts, our research results on over 30 metallic melts including alloys and elements show a novel physical image: temperature induced liquid-liquid structure transition (TI-LLST) can occur hundreds of degrees over TL. On the other hand, the solidification behaviors and structures out of the melts experienced TI-LLST are distinct from those out of the melts before TI-LLST. In this presentation, some characteristic aspects of the TI-LLST and the effects on solidification behaviors and structures are briefly summarized, and the pertinent rules and mechanism are also analyzed.

Jan 1, 2009

By Theo Lehner

The Rönnskär smelter has wide experience in the field of recycling of non-ferrous metals. Today, smelting and refining from primary and secondary raw materials are integrated in a complex flow sheet. Boliden operates a lead flash smelter, a lead refinery, a copper smelter and refinery, a sulphuric acid and sulphur dioxide plant, a slag fuming plant and precious metal plant at its Rönnskär smelter in the North of Sweden. The Business Area Smelter Operations also incorporates Boliden Bergsöe, Sweden's lead-acid battery recycler, and Norzink, Norway, where recycled zinc accounts for more than 20% of it's production. Raw materials for the Rönnskär smelter include concentrates, ashes, slags, metallic scrap, electronic scrap and electric arc furnace (EAF) steel-making dust. This paper briefly describes current operations and illustrates current measures to improve productivity. Limits to recycling as experienced by a non-ferrous smelter are, illustrated. The deportment of critical elements contained in raw materials is also discussed.

Jan 1, 1998

By Hal dun Kurama

In thus-study, Bigadic upper zone zeolitic tuff, which contains about 87% clinoptilolite was used as an ion exchanger for removal of Pb++, Cu++, Cd++ and Hg++ ions from wastewater. Bench scale experiments with two different glass columns, were carried out continuously under the closed/ open circuit conditions. Before ion exchange tests, zeolite samples were treated with NaCI (6ml/ min. and 42BV). The effects of particle size, bed volume, pH and flow rate on the ion exchange capacity were determined. Under the best operation conditions, the effect of initial influent solution concentration on ion exchange selectivity was tested. As a-result, it was found that the Bigadiç clinoptilolite had the following ion exchange capacities;

Jan 1, 1995

By Klaus Gamweger

"This paper introduces an innovative solution to open and close the tap hole of different furnace types in the copper industry with a slide gate system. Two plates with defined drilled holes are slid against each other, which enables effective starting and stopping of the copper flow as well as throttling. Typically, the copper is poured via a tap hole into a launder system by rotating the furnace into an appropriate position. Control of the casting rate is also performed in this manner. Or, in case of stationary furnaces the tap hole is opened by oxygen lancing and closed manually with a clay- or copper-cone. These procedures show a lot of disadvantages including splashing, oxygen pick-up, and energy losses as well as a severe danger for the working staff. All these problems can be overcome with an appropriate slide gate system.IntroductionThe control of the casting rate of a copper anode furnace usually is performed by rotating the furnace into an appropriate position. This implies that the taping starts with the tap hole at a very high position. Copper splashing and an uncontrolled oxygen pick up are - with several more disadvantages - the consequences. RHI AG has developed an innovative solution for copper applications to open and close the tap hole with a slide gate system which allows also an accurate control of the flow rate. By using this system it is possible to start the casting procedure with the tap hole at the deepest position, directly above the launder. This paper presents this new slide gate system in detail and shows the advantages in production and safety issues."

Jan 1, 2012

By P. Balachandran

The paper outlines the existing facilities and working practices at the Khetri electro-refinery of Hindustan Copper Limited. Plans have been drawn up to mechanize some key operations to improve the quality of cathodes and the working environment as well as economize the refinery operations. The economic analysis for determining various optimum operational parameters under conditions existing in India have also been outlined. The impact of capacity utilization and mechanization under different sets of conditions on operational costs have been highlighted.

Jan 1, 1987

By Tom McCullough

The purpose of this paper is to discuss the implementation and results derived from installing oxy-fuel burners in a l80 ton copper reverbatory melting furnace. Specific results will be discussed in the areas of melt chemistry, furnace modifications, productivity, process enhancements, and the combustion system capabilities.

Jan 1, 1996

By Pan Gu, Zhen Zhang, Wen-Feng Tan, Jiang Diao, Bing Xie, Wang Zhou

In order to recover the chromium resource in chromium-containing vanadium extraction residue, a promising method is to prepare ferrochromium with the residue. The synthetic residue has been reduced under 1300, 1350 and 1400 °C at the reduction time of 1, 2 and 3 h respectively. The reduced samples have been smelted and separated by an induction furnace. The contents of chromium and iron in metallic phase have been determined by an inductively-coupled plasma spectrometer. The results indicate that chromium iron carbide (Cr, Fe)3C7 is the intermediate phase and titanium oxides have been reduced during the reduction process. While the sample has been reduced under 1400 °C for 3 h, metallic phase becomes the dominate phase and reduction reactions almost complete. Moreover, the chromium content in the metal phase reaches 10.19%.

Mar 1, 2017