Search Documents

By Zeyun Cai, Gaoyang Song, Bo Song, Yuhou Yang

In this research, super gravity field was introduced in the solidification process of high carbon steel. The experimental results show that the solidification structure of Fe–1 wt% C steel can be largely refined by applying super gravity at the cooling rate of 10 °C/min. Both the primary and secondary dendrite length was markedly reduced. In addition, the eutectic structure in the inter-dendrite was also refined with the obvious reduce of eutectic space. However, the macro-segregation of C along the direction of super gravity was caused with higher weight percent at the upper area than that at the bottom of the sample. The mechanism of solidification structure refinement and the C macro-segregation of Fe–1 wt% C steel in super gravity field were also discussed in this paper.

Mar 1, 2017

By Guan-Yong SHI, Cong Wang, Zhi-he DOU, Ting-an ZHANG, Shi-gang FAN

Based on the pre-works, this paper proposed a new short stage process of the intensify aluminothermy reduction by the stage to prepare high titanium ferroalloy with low O and Al contents. We investigated the effects of Al and Ca and Si combination reduction agent, slag type and step-up reduction conditions on the Al content and distribution in the alloy. The results show that the step-up reduction can not only reduce effectively the oxygen content in the alloy, but also reduce effectively Al content. For instance, the oxygen content in high titanium ferroalloy is within 1%~4%, and the Al content is within 1%~5%. Its quality reaches the requirement of high titanium ferroalloy prepared by remelting process.

Jan 1, 2015

By Tiezheng Li

Keywords: Laminate Composites; Mechanical Behavior; Damage Evolution The mechanical performance of Ti-6-4-Al3Ti metal-intermetallic laminate (MIL) composites synthesized by a reactive foil sintering technique was evaluated. Crack morphology of untested Ti-6-4-Al3Ti MIL composites has been characterized by optical microscopy. Mechanical tests were performed on Ti-Al3Ti metal-intermetallic laminate (MIL) composites and pure Al3Ti, and the principal mechanisms of damage initiation and accumulation were identified experimentally. The elastic properties and anisotropy of the laminates were calculated and successfully compared with Resonant Ultrasonic Spectroscopy (RUS) measurements. The effect of residual stress on the fracture toughness of the Ti-6-4-Al3Ti MIL composites was analyzed.

Jan 1, 2005

By Peter Olubambi, Babatunde Obadele, Oluwagbenga Johnson

"The microstructure and corrosion behaviour of titanium carbide (TiC) reinforced duplex stainless steel matrix surface composites synthesized by laser melt injection technique was investigated. The surface melting operation was conducted using a 4.4 kW CW Nd:YAG laser with laser power of 1.5 kW, scanning speed of 0.4 to 1.0 m/min, beam size of 3 mm and argon shield gas flow rate of 4 L/min. The morphologies and microstructures of the coatings examined using field emission gun scanning electron microscope (FEGSEM) revealed homogeneous distribution of fine precipitates of TiC in the matrix, while X-ray diffraction (XRD) analysis confirm no phase change. TiC addition to the steels significantly increased hardness value to about 547 Hv0.1 but slightly decreased the corrosion resistance of the steels in 3.5% NaCl possibly due to the intergranular carbide coating that prevented chromium from forming continuous passive oxide layers.IntroductionComposite materials evolve from the idea of combining two basically dissimilar materials with different physical and mechanical properties to arrive at a product whose final properties are superior to those of the individual components [1]. Metal matrix composites (MMCs) are receiving much attention and are the focus of intense research and development worldwide for aerospace, automotive and other applications because of their excellent combination of ductility and toughness of the metallic matrix with high hardness and strength of carbides reinforced in the matrix [2]. Surface modification techniques such as laser, thermal spray, plasma spray, chemical vapour deposition have been use to fabricate MMCs. Laser melt injection (LMI) is a surface modification technique known since the 1980s [3] has been used to improve surface properties of metallic alloys such as aluminium, titanium and steels [4-6]. It involves the lateral injection of carbides, ceramics and cermets blown by a gas stream into a liquid metallic pool, created by laser irradiation of the top surface of the base material."

Jan 1, 2012

By Toshiyuki Kozuka

CdTe metal composite semi-conducting material has high potential in good performance of energy conversion efficiency for solar cell and there is much room for improvement of the performance by developing a process of making a thin CdTe film. In this paper, the imposition of intense magnetic field on CdTe electro-depositing surface is proposed, which is one of the possibilities for improving the energy conversion efficiency. In the experiment, cryogen-free super-conducting magnet up to 5T was used and CdTe film was deposited electrically in -o.nv vs. SHE The electrolyte was Cd and Te ammonia alkali solution with controlled temperature in the acrylic cell of 70mm diameter. Electro-deposition behavior of CdTe has affected by the imposition of the intense magnetic field due to microscopic convection in the vicinity of the depositing surface. Electro-deposited surface of CdTe becomes smooth due to microscopic convection around the surface, and the crystallization behavior is also affected, where crystallization temperature and the grain size is changed by the imposition of intense magnetic field.

Jan 1, 2003

By Murat Baydogan

Effect of retrogression and reaging treatment on hardness and stress corrosion cracking resistance of 7075 aluminum alloy was investigated. As received 7075 alloys in T6 temper condition were retrogressed at 170, 220, 240 and 380°C for different durations between 15 s and 60 min. Subsequent reaging was made at the T6 aging condition. Treated materials exhibited higher hardness and better stress corrosion cracking resistance than T6 temper in a wide range of retrogression temperature and time. The highest hardness was obtained after retrogression at 170°C for 210 s followed by reaging, corresponding to 20% hardness improvement. Improvement in stress corrosion cracking resistance of the alloy by as much as 85% was also observed. In this paper, improvements in hardness and stress corrosion cracking resistance are discussed on the basis of the microstructural changes during retrogression and reaging treatment.

Jan 1, 2006

By Yoichi Takeda

The CaO-FeOx-Cu20 slag has been practically applied to continuous converting of copper, and also has potential for refining of copper. Liquidus lines of the slag system and phase stability diagram for the liquid slag and the existing solid compounds under copper saturation are presented. Liquidus composition was determined by chemical analysis of slag sample saturated primary solid. The temperatures of invariant equilibria were investigated by thermal analyses. Oxygen potentials on the liquidus lines, the univariant and invariant equilibria were estimated from the relation slag composition and oxygen potential that relation was confirmed in separate experiments.

Jan 1, 2003

By Othon do Rêgo Monteiro Neto

[The present study has investigated the extraction of copper from a chalcopyrite flotation concentrate using an adapted strain of Thiobacillus ferrooxidans and shake flasks, tank leaching and Warburg respirometer techniques. From the shake flask experiments, the activation energy and the frequency factor have been determined to be ?ka = 59.4 kJ and A = 3.3 x 105 S-1, respectively. The temperature coefficient was found to be Q10 = 2.2 in the range of 20 to 35°C. It was suggested that the reaction mechanism of chalcopyrite leaching by T. ferrooxidans involves the formation of an activated complex. whose thermodynamic values have been calculated to be ?G? = 92.1 kJ, ?S? -148.8 J K-1 and ?H$ = 47.8 kJ. The maximum volumetric oxygen mass transfer coefficient for the reactor leaching was found to be achieved by using an optimum air flow rate of 1970 cm min l at a rotational frequency of 1000 min-1. The highest copper extraction in tank (reactor) leaching experiment was 86.8% after 17 days of leaching, while in the sterile runs the corresponding copper extraction was only 40.1%. The copper extraction was suggested to be diffusion controlled. The power requirement of the aerated reactor was calculated to be Pg = 2.02 watts. During leaching, the oxygen saturation concentration was found to be C* = 6.70 mg dm-3. Using the gassing out method the critical oxygen concentration was assessed to be CCrit 0.05 mg dm 3. From the Warburg experiments, the kinetic parameters of the Monad equation were derived with a new evaluation technique to be Vmsp = 9.0 µm3 02 min-1 mg protein-1 and K = 7.4% pulp density for the effect of substrate concentration. The order of reaction and the overall reaction rate constant were determined from the modified van't Hoff plot to be n = 0.0 and k = 1.49 p dm3 02 min-1 mg Protein -1 for the chalcopyrite concentrate oxidation by T. ferrooxidans. On the basis of this experimental work, a preliminary flow sheet has been proposed for the bioextraction of copper from flotation concentrates.]

Jan 1, 1985

By Jian Yang

The mechanism of resulfurization in the desulfurization process with magnesium vapor produced in situ by aluminothermic reduction of magnesium oxide was clarified in the present work. The influences of various operating parameters on the resulfurization were studied and the methods that could prevent resulfurization were proposed. There are two kinds of mechanisms of resulfurization in the desulfurization process with magnesium. One is decomposition of the desulfurization product of MgS under the inert atmosphere. The other is oxidation of MgS under the oxidative atmosphere. Under the present experimental conditions, lowering operating temperature and oxygen partial pressure in the atmosphere could effectively prevent the resulfurization. Adding CaO onto the melt surface was an effective method for preventing the resulfurization due to transformation of the desulfurization product of MgS into the more stable compound of CaS. Since addition of the activated charcoal powders greatly decreased the transfer rate of oxygen in the atmosphere to the melt surface, it also reduced the resulfurization remarkably.

Jan 1, 2006

By Mehdi Asadi, Heinz Palkowski

"In recent years, the increased demand for advanced high-strength steels (AHSS) mainly had been driven by the need of the automotive industry to reduce weight and to improve safety. Beside good ductility and high strength, those steels have a high bake hardening (BH) effect, giving additional contribution to the strength of structural parts, subjected to the paint baking process. In this paper we concentrate results gained for hot rolled dual phase (DP) steels.For the simulation of changing process conditions within the final hot rolling the specimens were hot deformed using different schedules of temperatures and reductions, selected according to the non-recrystallization temperature (TnRX). It was possible to refine the DP steel structure by control-ling the deformation temperature and the amount of strain below TnRX during the thermo-mechanical controlled processing (TMCP). This structure refinement resulted in an improvement of the strength and BH behaviour. A wide spectrum of mechanical properties could be obtained depending on the different hot deformation schedules. The best strength and BH levels were recorded for the deformation below TnRX at the highest amount of strain.IntroductionDP steels are characterized by a good formability, high strength and a good compromise between strength and ductility [1]. Moreover, the DP steels exhibit a continuous yielding behaviour, low yield point and a high strain-hardening coefficient [2]. Furthermore, the DP steels often show a large potential for bake hardening (BH). BH refers to the increase in yield strength as a result of the paint baking treatment of the shaped auto-body parts. The primary mechanism that causes the additional strengthening is the immobilization of dislocations by the segregation of interstitial atoms, known as classical static strain aging [3]. The increase of strength thus achieved allows a further reduction of sheet thickness and improves the crash safety and the dent resistance. The BH of special steel qualities is technically used in DP, where e.g. the increase in strength is realized in the final heat treatment [4]. Previous own investigations [5-6] stated that the BH effect of DP is much stronger than that one for conventional BH steels."

Jan 1, 2012

By R. M. Taylor

Lime addition to acid mine drainage (AMD) leads to precipitation, predominantly of metal hydroxides and calcium sulfate, and is the benchmark for remediation by precipitation. Geo2 Limited of Melbourne, Australia has developed and patented a novel alternative precipitation scheme based on the formation of mixed valency, M(I1)-M(III), hydroxide sulfate salts. When the composition of AMD is appropriate, the Green Precipitate Process provides a useful and more effective alternative to conventional liming. The characteristics and utility of the Green Precipitate Process are described in terms of the underlying chemistry, and a case study where the Green Precipitate process outperforms conventional liming. A mobile pilot pipe reactor rig which was built by Geo2 to demonstrate the process, and used successfully in both Australia and the United States, is described.

Jan 1, 1998

By KNona C. Liddell

The ion interaction model Pitzer proposed twenty years ago is today the most widely used method for calculation of osmotic coefficients and electrolyte and single ion activity coefficients in aqueous solutions. This is due in part to the accuracy of the results that have been obtained for many concentrated electrolytes. An additional factor is that, compared to alternative activity coefficient models, there are many more parameter values available for the Pitzer equations. The important features of this model are reviewed. Published parameter values for Co, Ni, Cu, Zn and Fe are tabulated, and applications of interest in the aqueous processing of these metals are described.

Jan 1, 1993

By Alexey Lozhko

The technical-and-economic furnace exploitation indices are considerably influenced by the system of heat utilization. In the situation of total output decrease works are forced to exploit furnaces at the partial loading, sometimes even at the idle running for the sake of steam production. The furnace exploitation in this regeme is known to cause the increase of the heat portion, taken away together with waste flue gases. The losses can be partially compensated at the expense of heat exchange efficiency development in the recuperator or heat-exchanger. One of the well-known methods, characterised by high efficiency and low expenditures is the intencification of the heat exchange process by the means of pulsation method.

Jan 1, 2006

By Elli Nurminen

In this work the thermodynamics of the metallic sulphate decomposition reactions were studied through thermodynamical calculations and thermogravimetric methods. The decomposition temperatures and mechanisms were determined for cupric sulphate, ferric sulphate and also for industrial flue dust from a copper flash smelting process. The aim was to determine the thermodynamic conditions for sulphate decomposition and to estimate whether the reactions are kinetically likely to take place in the flash smelting process heat recovery equipment. The information is essential in CFD-modelling of the reactions taking place in the boiler and for optimising the process.

Jan 1, 2006

By S. P. Ball

A major limitation to maximising the rate of gold extraction in commercial operations occurs as a consequence of the limited solubility of oxygen in cyanide liquors. The use of additions of solid inorganic peroxides as an in-situ supply of oxygen to the lixiviant has been studied, in particular in its application to heap leaching. Experimental studies showed-that the release of oxygen into solution from these peroxides is very sensitive to solution pH. Agitated leaching tests showed that, when either Ba, Ca or Sr peroxides were used as the-sole source of oxygen, both the rate and extent of gold extraccion was enhanced. Column leach tests were used to simulate heap leach conditions. These showed that significant increases in the rate of gold extraction could be achieved by additions of calcium peroxide, made to the ore, prior to it being loaded into the columns.

Jan 1, 1989

By Peiye Yan, Huiqing Tang

To reduce coke consumption in blast furnace ironmaking, this study proposed a new method of applying iron-coke briquette prepared using hematite powder and pulverized coal to protect coke in BF iron making. Results showed that, with a ratio of hematite to coal of 2.0, the iron-coke briquette could obtain a satisfying compressive strength of more than 1500 N both before gasification and after being gasified by CO2 for 1 h. The activation energy of the iron-coke briquette was 93–135 kJ/mol, which is lower than the coke and therefore could protect the coke in BF. The agglomeration and stratification of iron particles occur in the course of iron-coke briquette gasi fication and is bene ficial to the improvement of the iron-coke briquette strength.

Mar 1, 2018

By Thierry De Nys

A direct leaching process of sulphidic zinc-based concentrates in aqueous sulphuric acid solutions has been developed by the V.M. R & D Department. By a very accurate control of the oxidation potential of the leach solution, this process enables a separate recovery of the zinc, copper, silver, lead and sulphur of the concentrate and makes it extremely attractive for treating more complex ores. The iron, solubilized during leaching, is eliminated out of the zinc solution by means of the V.M. goethite process. Alternative flow sheets for a conventional zinc electrolysis plant are presented.

Jan 1, 1990

By Wang Jingsong, Ma Tengfei, Feng Fu, She Xuefeng

In this paper the direct reduction melting separation-leaching process is investigated on recovering rare earth from rare earth Bayan Obo complex iron ore (REBOCIO). The REBOCIO was reduced and melting separated to produce iron nugget and rare-earth-rich slag at 1400°C for 12 or 15 min. The RE2O3 is enriched into Ce 4.667(SiO4)O or Ca 3Ce2[(Si,P)3O4]3F, which closely depend on chemical components, especially basic. The optimal acid-leaching parameters of rare earth elements from the rare earth slag are suggested as the hydrochloric acid concentration, the ratio of solid to liquid, leaching temperature, and the leaching time are 1 mol/L, 1:14, 50 °C and 120 min, respectively. The rare earth elements leaching efficiency are more than 95%. Adding of calcium CaCO3 and sodium Na2CO3 in direct reduction process have great in fluence on leaching ef ficiency of thorium.

Mar 1, 2018

By J. Priede, G. Gerbeth

"Two different instability mechanisms of electromagnetically levitated bodies are analyzed. The first is due to the virtual coupling between the electric current passing through the magnetic system and the variation of position of the body. This mechanism can result in unstable mass center oscillations of a levitated solid body. Another type of instabilities may occur because of the coupling between the motion and the electric currents induced in the body. This effect can cause a spontaneous rotation of the body setting in as the frequency of the alternating magnetic field exceeds certain critical threshold depending on the configuration of the field. This instability can be suppressed by an axial steady magnetic field of strength comparable to that of the levitating field. 1 IntroductionAn alternating magnetic field interacting with eddy currents induced in a conducting body causes repulsion between the body and the coil generating the field. Besides, the eddy currents provide a contactless heating of the body. In such a way metallic samples can be levitated and melted without a contacting crucible. This technique allows to avoid contamination of the melt with container material and so to achieve a considerable super-cooling of the melt before it solidifies. Nowadays electromagnetic levitation is widely used in material research for measuring of the thermophysical properties of molten metals (2) .It has been observed since early fifties when the first experiments on the electromagnetic levitation were done that under certain circumstances solid levitated samples start to rotate or oscillate [l]. Surface oscillations can appear in addition when the sample is melted. Such phenomena are undesirable because they often result in failure of the levitation. Recently we showed that rotational as well as oscillatory instabilities can have electrodynamic origin related to additional eddy currents induced by motion of the body in an alternating magnetic field [3] , [4].In the first part of the present paper we analyze another possible cause of oscillatory instability due to the coupling between the electric current passing trough the magnetic system with variation of the position of the levitated body. The second part of the paper deals with the origin and suppression of rotational instability in a uniform alternating magnetic field."

Jan 1, 1999

By Shujian Jia, Mingming Song, Gaoyang Song, Bo Song, Yuhou Yang

An innovative method is investigated to separate inclusion particles from liquid metal by super gravity. To make clear the characteristics of the inclusion separation, Al melt containing MgAl2O4 particles with diameters less than 150 μm has been treated under various super-gravity fields. The thickness of particle-accumulated layer formed at the bottom of the sample and the area fraction, number density and size of inclusions were measured. It is found that the thickness of the particle-accumulated layer decreases and the area fraction of particles at this location increases with the increase of super-gravity field. With the gravity coefficient G=500, time t=2 min, and temperature T=1023 K, it is hardly to find any solid particles in the upper and middle areas of the sample and the separation efficiency is up to 90%.

Jan 1, 2015