Search Documents

By Nan Zhang, Lei Zhang, Gai-feng Xue, Lina Wang, Pu Liu

"A novel ß-diketone modified silica gel was synthesized by a simple reaction. The prepared material was characterized by diffuse reflectance FTIR spectroscopy and it was used for the adsorption of heave metal ions in the industrial waste water. The main parameters affecting the sorption of heavy metal ions, including pH, water flow rate, and elution, have been investigated in detail. Under the optimized operating conditions, most of the targeted heavy metal ions could be removed. The material could be simply regenerated by hydrochloric acid solution. The method is rapid, selective, economic and applicable to the removal of heavy metal ions from industrial waste water.IntroductionToxic organic pollutants and heavy metals ions mainly from industrial activities such as plating, metallurgy and dyeing industries, are a threat to human health and the surrounding environment, because of their toxicity and persistence after being released into the natural environment [1]. These pollutants must be removed or degraded to an acceptable level, before being discharged to the receiving waters. Therefore, detection and determination of heavy metal ions in industrial waste water is very important.Inductively coupled plasma optical emission spectrometry (ICP-OES) is the most used technique for the determination of heavy metal ions because of its capability for rapid multi-element detection over a wide concentration range and with relatively low detection limits. Compared to other techniques such as neutron activation analysis (NAA), X-ray fluorescence spectrometry (XRF) and inductively coupled plasma mass spectrometry (ICP-MS), ICP-OES has the above advantages. Some constituents in industrial waters, such as organic compounds and inorganic salts, may cause matrix effects. In order to achieve accurate and reliable results, an efficient preconcentration of heavy metal ions and their separation from the matrix are usually required."

Jan 1, 2012

By Kwang-Ho Lee

The Onsan copper smelter of LS-Nikko Copper Inc. has operated the Mitsubishi continuous process along with Outokumpu process since 1997. Mitsubishi process is a bath smelting process which needs adequate melts for smelting reaction in the furnace. After a campaign shutdown it requires time to make a start melt. Onsan smelter has had much experience in flash smelting, including the improvement of the concentrate burner which is one of the most important parts in a flash smelting furnace. Based on this experience, the lances of the Mitsubishi smelting furnace were modified in order to making the starter melt with flash reaction. In 2004, the flash reaction in the Mitsubishi S-furnace was completed and was able to make the starter melt using these modified lances. Although at that time it was still under development it reduced the time required to make the initial bath-melt by about half.

Jan 1, 2006

By Chai Liyuan

Chromium-containing slag was detoxified by the method of microbial treatment using Ch-1bacteria isolated from nature by our research group, belonging to achromobacter sp. and with the characteristic of reducing high concentration of Cr(VI) in alkaline solution. The detoxifying process of Ch-1 to chromium-containing slag was studied by column-leaching techniques respectively. The results indicate that Cr(VI) in leachate can not be detected when chromium-containing slag has been column-leached for 7 days, and Cr(OH)3 content in precipitate is up to 32.8% with great value of resource recycling. Flowchart of engineering experimentation was ascertained based on the parameters of column-leaching experiments. Using the technique of pelletization of chromium-containing slag heap-leaching by Ch-1,the leaching rate of water-soluble Cr(VI) existing in chromium-containing slag reaches up to 100%, while the leaching rate of full chromium is up to 90%, when the process has been operated for 7-10 days under the conditions of 25-40C and consecutive spray by circular leachate. The content of Cr(VI) in chromium-containing slag after detoxified meet the national identification standard for extraction procedure inxicity for hazardous wastes(GB5085-1996) in China, moreover approximately 90% of Cr(VI) existing in chromium-containing slag has been recycled.

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Torben L. Edens

Norddeutsche Affinerie is the largest copper producer in Europe. Two sites are in operation for the production of refined copper: primary copper production is located in Hamburg and secondary copper production in Lünen. A total of just under 560,000 tonnes of copper cathodes is produced annually at the two sites. Primary copper production using the flash smelter furnace has been in operation in Hamburg since 1972. Over the years, the capacity of the flash smelter has been increased in three expansion projects from 120,000 t to almost 500,000 t of anode copper p.a. The anode sector consisting of two anode furnaces and a 24 mould casting wheel still features just about the same equipment as in 1972. The paper describes the most important steps taken to optimise operation which have put NA in a position to cast meanwhile more than 500,000 t of anode copper annually with the two anode furnaces and 24 mould anode casting wheel.

Jan 1, 2006

By Henk Dijkman

Existing metallurgical operations can be optimized by implementing engineered bioreactor systems in the process configuration. For instance, metals can be recovered safely and economically from process and waste streams using biogenic sulfide. This paper focuses upon possible applications of high rate biotechnology in metallurgy and mining. Metal recovery from liquid streams (process bleed streams, leach water, waste streams), integrated removal of (fugitive) SO2, treatment of acid blowdown and other options will be described. Practical examples are given. A large-scale application of biotechnology at Pasminco's Budel Zink refinery is described. Here, acid plant blowdown is treated together with electrolyte magnesium bleed. Concentrated zinc sulfide (10 tpd) is produced biologically, eliminating the production of gypsum and closing the refinery sulfur cycle. Recovery of metals from solution at Kovehute Pribram in the Czech Republic is the second practical example. In this case, H2S is produced on-site for metal removal from an alkaline slag dump leachate. At the Caribou mine in New Brunswick, Canada, acid mine drainage is treated with biogenic sulfide. This plant is situated upstream of a lime neutralization plant. As a result, reusable ZnS is produced, the volume of the sludge (gypsum and hydroxides) from the lime plant is reduced by 50%, the sludge is free of heavy metals and the final effluent concentration of heavy metals is in the ppb range. In the second phase of this project, metals will be recovered from stored tailings, resulting in significant revenues.

Jan 1, 2002

By Petr Stehlík

"This paper is aimed at showing and demonstrating progress in technologies and improvements in units for the thermal processing of various types of waste. The following areas are covered: units for the thermal treatment of hazardous industrial waste and common MSW, technologies for the thermal treatment of industrial and sewage sludge, utilizing waste in cement production (material and energy recovery), up-to-date off-gas cleaning systems, original and unique units for the thermal processing of polluted gases, low-NOx burners. The paper represents a review based on industrial applications, papers published in reputable international journals and a monograph under preparation.IntroductionThe present contribution is an overview of the activities and achievements of the Institute of process and environmental engineering (UPEI) of the Brno University of Technology (VUT). The Institute belongs to European leading teams in the field of the thermal processing of various types of waste. The research in the institute currently revolves mainly around a strategic project “Waste and Biomass Utilization focused on Environment Protection and Energy Generation” that is supported by the national government. Due to the limited space this paper is conceived as a review of papers published especially in reputable international journals.Main (strategic) target of the research is development of new, efficient processes (eventually modernized processes with novel original elements) for effective and highly efficient treatment of waste and biomass, including their maximum utilization as renewable energy sources while minimizing harmful emissions. To this purpose, highly advanced know-how for the design and construction of the related technology lines is being developed, supported by mathematical modeling (see e.g. [1]), experimental validation and optimization.Municipal and Industrial Solid Waste – Concept of Waste-to-Energy CentersThermal processing of various types of wastes is not only waste disposal and/or treatment at present. It has to be regarded as waste to energy process wherever and whenever possible and feasible. This observation was at the origin of the concept of new regional Waste-to-Energy Centers (WTEC), outlined in the following paragraphs. The proposal of the centers is based on a combination of experience, know-how and sophisticated approach. The main fact influencing the concept of WTEC is the necessity to treat different types of wastes. Typical types of wastes as well as main products of the processes in a WTEC are shown in Figure 1."

Jan 1, 2008

By Feng Ningchuan, Guo Xueyi, Tian qinghua, Liang Sha

"In this study, copper adsorption by orange peel which was chemically treated with sodium hydroxide was investigated. The morphological and chemical characteristics of the adsorbent were evaluated by spectroscopy and N2-adsorption techniques. Equilibrium isotherms and kinetics were obtained and the effects of solutions pH, adsorbent concentrations and temperature were studied in batch experiments. Equilibrium was well described by Langmuir and Freundlich isotherms and kinetics was found to fit pseudo-second order type adsorptions kinetics. According to the Langmuir equation, the maximum adsorption capacities (qm) for Cu(II) was 50.25 mg·g-1 at pH 5.3. With the temperature increased from 16 to 60°C, copper removal decreased. The loaded adsorbent was regenerated using HCl solution and could be used repeatedly at five cycles with little loss of adsorption capacity. The results show additional chemical treatment of the adsorbent by NaOH, is favor of improving the adsorption capacity. Introduction Increased use of metals and chemicals in manufacture industries has resulted in generation of large quantities of effluent that contains high level of toxic heavy metals and it poses environmental-disposal problems due to its non-degradable, persistence nature and accumulation throughout the food chain [1, 2]. Copper is known to be a commonly used heavy metal. This metal, which found many useful applications in our life, is very harmful if charged into natural water resources and may pose finally a serious health hazard. Many methods, such as chemical precipitation, ion exchange, reverse osmosis and adsorption, etc., have been used for heavy metal ions removal from various aqueous solutions. In recent years, there has been considerable interests in use of biological materials including algae, bacteria, fungi, agricultural by-products and residues as adsorbents to remove toxic metals from aqueous solutions by adsorption [3-8]. Adsorption process has been extensively used to remove copper from aquatic medium using low cost adsorbents such as peanut husks [9], plant materials [10] and cellulose materials [11]. Among them, agricultural by-products and biomass are relatively cheap and show very high adsorption capacities. However, to apply untreated agricultural by-products as adsorbents has the disadvantages such as low adsorption capacity, high chemical oxygen demand (COD) and biological chemical demand (BOD) as well as total organic carbon (TOC), due to the release of soluble organic compounds contained in the plant materials such as lignin, tannin, pectin and cellulose, into the solutions [12-14]."

Jan 1, 2008

By M. Misra

The volume of low-level contaminated soil at the. Department of Energy's Nuclear Weapon Sites are in the order of several million tons. Most of the contaminants are uranium, plutonium, other heavy metals and organic compounds. Selected Physical separation processes have shown demonstrated potential in COD Centratingthe radio nuclides in a small fraction of the soil. Depending upon the size, nature of bonding and distributions of radio nuclides, more than 90 percent of the radio nuclide activity can be concentrated in a small volume of fraction of the soil. The physico-chemical separation processes such as flotation in a mechanical and microbubble tall column cell have shown, promising applications in cleaning up the high volume contaminated soil.

Jan 1, 1995

By René Bustamante

A GPSS/H simulation is beeing done for a traditional smelter of copper, which envolves a reberberatory furnace, a set of Peirce Smith converters (PSC) and a refining furnace. The objective is to try different plant layouts, being the handling of liquid material at high temperature one the mainly concern, this envolves a study of the ladles and cranes used. Some of the modifications that can be evaluated through the model is the role of oxygen potential when tonnage oxygen is used, number of cranes, PSCs in operation, etc.

Jan 1, 1992

By Patrick R. Taylor

A novel method for Chemical Vapor Infiltration (CVI) using plasma technology is proposed, Plasma Enhanced CVI (PE-CVI). Due to the low rates at which CVI is currently performed, the use of plasma as a source of heat may be considered to be a faster and less expensive production method. Precursors fed in the hot region of the plasma gas are completely vaporized and forced by the same flow through a porous preform where it condenses as a new material. In this research, silica and methane where used as precursors to form SiC/on a / graphite felt (preform). To enhance the infiltration process, vacuum was used to increase the flow through the preform. Characterization of infiltrated graphite was perfontied using Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD). A uniform distribution of Sic was observed along the felt with only twenty minutes of infiltration process, yielding a 178% increment in weight.

Jan 1, 1997

By Hong Yong Sohn

On the occasion of this symposium in my name, I reflect upon the contributions of my academic mentors and early associates who helped shape my professional career. I was fortunate to have these people around me during my graduate work and at the start of my professional career. In forming my view of the technical field and career, they represented academia, research institutions, industry, and different parts of the world.

Jan 1, 2006

By S. S. Chabot, S. E. James

A recent survey of major steel companies worldwide revealed the importance of recycling zinc units from electric arc furnace (EAF) dust, mill scale, blast furnace dust and other zinc containing streams within the steel industry. Many processes have been developed and installed in response to this challenge. The most successful approach involves the production of a crude zinc oxide and its sale to primary zinc producers to recover the metal values. The problem with this process is the high concentration of halides in the crude oxide. This type of material cannot be processed directly in an electrolytic zinc plant because of the corrosion problems it will cause in electrolysis. In 1999, Big River Zinc installed a zinc oxide receiving and washing plant to minimize the impact of halides in its electrolysis circuit. A description of the washing plant and the initial operating results are presented in this paper.

Jan 1, 2000

By M. Hashiuchi

In 1972, the tankhouse of the Tamano Smelter adopted a high current density electrolysis operation applying the PRC (Periodic Reverse Current) method. In 1994, the phase four production expansion project, which incorporated significant re-structuring of the organization, was completed and we have achieved an annual production capacity of 191,000 tons. The target of this project, the production capacity, was increased by 1'8% and labor productivity by 25%. After the expansion, some improvements in the starting sheet section and the verticality of the electrodes were carried out, and the efficiency of the operation was greatly enhanced, including the improvement of the quality of the electrolytic copper.

Jan 1, 1999

By C. Anderson

Most applications of copper metallurgy are geared towards primary production. However, as recycling of materials is a growing industry, one future facility will rely on copper metallurgy as a means of processing precious metals. This paper will discuss the derivation of the proposed copper pyrometallurgical and electrometallurgical unit operations to be utilized in industrial recycling of secondary precious metals.

Jan 1, 1999

By Varadajan Seshadri

The increase in production of continuous casting machines requires long ladle sequences without interruption. Very often the production schedule has to accommodate a variety of steel grades. In such cases downgrading may be inevitable. Models must be made available to study the alternatives that would make possible mixing of steels in the tundish but minimizing the losses due to downgrading the slabs. Physical modeling was used to evaluate the influence of variables such as internal geometry of the tundish, presence of turbulence inhibitors, depth of ladle long nozzle, weight of steel in the tundish, steel throughput upon the tundish transition curve. Expressions for minimum residence time and transition period have been determined. Mixing-transition is allowed to continue inside the liquid pool in the mold and the final solute distribution in a given cross section is captured by a solidification model. The result is a map of the transition in the final product.

Jan 1, 2006

By V. M. Paretsky

Recent developments made in the Gintsvetmet Institute in the field of autogenous smelting processes have confirmed that autogenous smelting continues to be the main prospective technology for pyrometallurgical processing of sulfide raw materials. This technology ensures energy conservation and environmental safety conforming to the current world standards for production of heavy non-ferrous metals. Two alternative processes of single-stage autogenous smelting producing white metal as well as high-basic ferrite-calcium slags have been developed and can be recommended for technical modernization of Russian copper smelters.

Jan 1, 2002

By Weyman Dunaway

This paper will present a description of the development and commissioning of the world?s most efficient process for manufacturing high purity aqueous zinc bromide. The method for making aqueous zinc bromide from metallic zinc and bromine comprises contacting zinc with bromine dissolved in a reaction solvent containing a metal halide salt. The reaction temperature is maintained at less than 60°C. The reaction solvent preferably comprises an alkali, alkaline earth, or transition metal halide; the halide salt preferably comprises a chloride or a bromide. One preferred method includes the step of recirculating the zinc bromide product stream back to the reaction vessel. The reaction vessel can be either a one stage or a multiple stage reactor. The resulting product stream is a high density aqueous zinc bromide solution. The process is so novel that Tetra Technologies, Inc. was awarded US Patent Number 6,036,937.

Jan 1, 2006

By Peter J. Hancock

The pyrometallurgical .processing of non-ferrous, complex materials and wastes will be surveyed. Pyrometallurgy offers the most versatile way of processing a large variety of such materials because of its high temperatures, closely-controlled oxidation potential and the availability of commercially-proven reactor configurations. Some current industrial applications will be reviewed and possible new applications as well as future trends will be outlined.

Jan 1, 1994

By L. N. Ertzeva

The process for thermal treatment of current pyrrhotite concentrate in reducing environment with the use of disperse metal iron as an iron-bearing additive (optimal volume 20-30%), with downstream magnetic separation of the calcine, has been studied. The reduction process has been performed in conditions emulating those of both tube and fluidize-bed furnaces.

Jan 1, 2006