Search Documents

By Naoki Hiroyoshi

It is generally accepted that ferric ions are effective for leaching chalcopyrite as an oxidant and ferrous ions contribute to the leaching only as a source of the oxidant ferric ions. However, this paper shows that ferrous ions are more useful for leaching chalcopyrite than oxidant ferric ions in sulfuric acid solutions in air at ambient temperatures. Leaching experiments and dissolved oxygen consumption measurements were carried out with a very pure chalcopyrite and 0.001 - 1 mol dm-3 sulfuric acid solutions containing 0 - 0.1 mol dm-3 ferric or ferrous ions at 303 K. Chalcopyrite oxidation with dissolved oxygen was promoted by ferrous ions but suppressed by ferric ions. As a result, the amount of extracted copper was larger with ferrous ions than with ferric ions. Effects of Thiobacillus ferrooxidans on the ferrous promoted chalcopyrite leaching were also investigated and discussed based on the experimental data.

Jan 1, 1999

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Mitsuru Tanahashi

Oxidation removal of boron from molten silicon by injecting oxygen and highly basic CaO-CaF2flux powder has been investigated with special attention to the dynamic behavior of the injected flux particles and gas bubbles. Since oxygen gas is injected into the melt, high oxygen partial pressure is maintained at the flux-O2-Si interface and the removal of boron proceeds under nonequilibrium conditions. By applying this process, boron concentration in metallurgical-grade silicon can be reduced to a single-ppm level. In this paper, the effects of the dynamic behavior of the flux particles injected into the silicon melt and the area of the reaction field (the flux-O2-Siinterface) formed in the vicinity of the flux-gas exit of the injection nozzle on the rate of the boron removal are discussed from the viewpoint of process dynamics. The experimental results clarified that the boron removal rate is affected by the kinetic energy of the flux particles which is determined by the injection conditions, such as the gas-flow rate of oxygen and the size of the flux particles. At higher oxygen gas-flow rates, the injected flux particles are expected to possess a significantly high kinetic energy such that they penetrate the O2-Si interface formed at the nozzle exit, which results in the formation of a new reaction field for boron removal. On the other hand, at lower gas-flow rates, the injected flux particles possess too low kinetic energy to penetrate the interface. In this case where the formation of the reaction field is limited, it is shown experimentally that the rate of the boron removal is constant, independently of the flux injection rate.

Jan 1, 2006

By Kang-In Rhee

Nonferrous metal recycling not only provides energy saving and environmental benefits but also is a significant factor in the supply of various types of metals used in our society. Recycling plays an important role in establishing the sustainability of materials. The total amount of recycled nonferrous metals by weight accounts for less than 5% but their value is larger than 50% compared to ferrous metal recycling which consists of about half of the total metal recycling in weight. This paper describes trends and typical achievements in nonferrous metal recycling and overviews the present and future of nonferrous metal recycling technology and business in Korea.

Jan 1, 2006

By Kang-In Rhee

Nonferrous metal recycling not only provides energy saving and environmental benefits but also is a significant factor in the supply of various types of metals used in our society. Recycling plays an important role in establishing the sustainability of materials. The total amount of recycled nonferrous metals by weight accounts for less than 5% but their value is larger than 50% compared to ferrous metal recycling which consists of about half of the total metal recycling in weight. This paper describes trends and typical achievements in nonferrous metal recycling and overviews the present and future of nonferrous metal recycling technology and business in Korea.

Jan 1, 2006

By Henry Salomon-De-Friedberg

Quebrada Blanca has had to overcome numerous challenges in achieving design throughput. The paper reviews how actual practice has evolved from the original design. The major challenges that were encountered from heap leaching to solvent extraction, the tankfarm and through to electro winning are discussed. The eventual solutions to some of the key issues are presented.

Jan 1, 1999

The physico-chemical principles of chloride hydrometallurgy are reviewed to rationalise the complex chemistry in chloride-based processes for metal sulphides in terms of the predicted Eh-log[Cl-] relationships, measured changes in activity of H+, Mz+, Cl- and solubility of Ag(I), Cu(I), Cu(II), Pb(II), Ni(II), Au(III), Sb(III) and Bi(III). These changes reflect the nature of chemical speciation, competing effect of hydration/hydrolysis and chloro-complexation,composite effect of increasing acid and/or salt concentration and decreasing water activity. Rate data for the dissolution of PbS and ZnS in HCl containing Fe(III) or Cu(II) are compared and contrasted to highlight the effect of acid and chloride concentration, water activity, and the nature of oxidant. It is shown that LiCl, NaCl and HCl influence the kinetics of oxidative PbS leaching based on their effect on solubility of PbCl2 co-precipitated with elemental sulphur on the mineral surface. Evidence for the beneficial effect of Cu(II) in sulphide leaching is discussed.

Jan 1, 2003

By Frank R. A. Jorgensen

Flash smelting is used to smelt a large proportion of the world's copper and nickel and some lead/zinc concentrates. Understanding the factors controlling the ignition of these concentrates is an important consideration in designing burners and maximising the throughput of the flash smelting process. The literature on the subject is briefly reviewed and techniques for the measurement of ignition temperature discussed. The mineralogy of the concentrates and the role of thermodynamics and phase diagrams in interpreting and predicting ignition behaviour are emphasised and applied to interpreting results obtained on a nickel concentrate.

Jan 1, 2002

By F. Field, R. Kirchain, J. Gregory

Utilizing alternative materials is an important tactic to improve the environmental performanceof products. Currently a growing array of materials candidates confronts today’s product designer. While life-cycle assessment (LCA) methods provide quantitative input into this selection decision, their implementations are evolving and disparate. The goal of this paper is to explore several major analytical variations of LCA implementations and the implications of these variants across a range of application contexts. Specifically, this paper examines analytical variations in valuation method and treatment of recycling by exploring allocation methods that affect product end-of-life. Case studies across a range of materials are presented, including materials that exhibit a spectrum in variation of environmental performance and material degradation between primary and secondary applications. Preliminary results indicate that the choice of analytical method can have real impacts on individual metrics and there are sets of analytical variation over which strategic results are strongly affected.

Jan 1, 2008

By Jean Frenay

Bacterial leaching tests have been carried out on Portugese pyritic ores containing zinc, copper, lead and silver as valuable elements. Both indigenous and isolated strains of Thiobacillus ferrooxidans were used. During the tests the factors pH, Eh and dissolved oxygen were measured and related to the leaching activity of the bacteria. Different means to estimate or determine the real bacteria concentration were examined. The influence of nutrient media and particle size has been evaluated. The role of galvanic couples was studied by electrical linking of mineralogical samples of pyrite, sphalerite and chalcopyrite. Leach residues were examined by optical microscopy to follow the mineralogical alterations during the leaching. The results show a rather good leaching of the sphalerite. However, the dissolution of copper from chalcopyrite is much more difficult, 50 % recovery never being obtained.

Jan 1, 1985

By Shaolong Chen

Feeding dry sulfide concentrate into smelting furnaces enhances process performance and reduces the energy consumption and exhaust gas flow. Direct heated rotary dryers and flash dryers have being replaced by rotary steam dryers featured by very low wear rate of the pipe heating elements and long maintenance interval. Impact of the drying processes on the environment receives more and more attention as the emission legislation tightens. In this regard, environmental factors such as SO2, CO2, dust and gas flow among rotary dryers, flash dryers and steam dryers were compared. Selection of a rotary steam dryer for copper and nickel concentrate drying would be an ideal solution to reduce the pollution of exhaust gas, as drying is achieved by indirect contact to the steam at relatively low drying temperature and as the off-gas contains almost only water vapor and air. The emissions can be significantly reduced and only small and simple off-gas handling units are needed.

Jan 1, 2006

By Andrey Dmitriev

The solution of set of equations for the bottom zone presented by a condition of a thermodynamic equilibrium, namely, an equilibrium constant of wustite reduction by carbon oxide, material and thermal the balances, supplemented by the equation of the heat balance for the top zone, allows to calculate the base indices of blast furnace smelting. The calculated indices are extreme accessible at the given parameters of charge and blast. Application of actual degrees of the use of gas instead of equilibrium allows the calculations of actual indices of the blast furnace smelting process.

Jan 1, 2006

By Jason Eric Sallee

Ongoing operations at the Cyprus Miami Smelter involve the use of an electric furnace for settling of copper matte from discard slag. Proper operation of the electric settling furnace is a major factor in minimizing losses of copper to the discard slag. Recent test work at the smelter has shown improvement in the operation of the electric furnace with a subsequent improvement with regard to the copper losses. This paper presents a general discussion of the Cyprus Miami Smelter operation, past results with respect to copper losses, recent operational changes and test work, and the subsequent results.

Jan 1, 1999

By D. J. Sellmyer

This paper is Intended to review recent developments in the application of rare earth-transition metal alloys as high density, rewritable data-storage media. First generation magneto-optic media are based on amorphous Tb-FeCo or GdTb-Fe alloys which are adequate but could use improvements In certain respects. A very difficult materials-design problem is encountered because of the following requirements: a sufficiently large Intrinsic uniaxial anisotropy, a Curie temperature in the range 100-300°C, a sufficiently high coercivity, a sufficiently high optical absorption, a high Kerr rotation, reflectivity and high carrier-to-noise ratio, a high storage density, a very fine and homogeneous nanostructure, long-term stability, and inexpensive production. , Fundamental issues such as the relationships between the nanostructure and perpendicular magnetic anisotropy, and electronic structure and Kerr rotation are discussed. Attempts to tailor the properties by rare-earth alloying and by preparing compositionally-modulated, nanostructured multilayers are outlined. Challenges and opportunities in competitive materials such as garnets, ferrites and Co/Pt multilayers are briefly discussed.

Jan 1, 1992

By Li Cheng

The SKS copper smelting process was jointly developed by Shuikoushan Mining Corp. and ENFI (Beijing Central Engineering and Research Institute for Non-ferrous Metallurgical Industries) in China. It is a new bath copper concentrate smelting process with oxygen enriched air. The pilot plant testwork was completed successfully in 1993. SKS has demonstrated to be an advanced bottom blown smelting process. This technology got the First Class Prize of Scientific and Technological Progress awarded by CNNC (China National Non-ferrous Metal Industry Corp.) in 1994. The SKS process has significant capital and operating cost advantages. Its environmental and industrial safety and hygiene performance represents a substantial improvement when compared to conventional technologies. The technology has generated great interest in the Chinese metallurgical industry. Feasibility studies and basic designs have been carried out to incorporate in retrofit and green field smelter projects in China and abroad. This paper describes the history of the pilot plant operating data (50 tonnes dry feed/day), and discusses the features of the SKS technology, its application and possible future trends.

Jan 1, 1999

By Pedro Morales C.

From its beginning in the 1970s, the Teniente Converter has consistently achieved continuous improvement, and has contributed to the competitiveness and sustainability of Codelco's copper operations. The later introduction of the Slag Cleaning Furnace technology has helped to create a full technology package, referred to as the Teniente Technology. This paper outlines the features of a new research and innovation program designed to bring the Teniente Technology as a modem, competitive technology into the 21st century. The overall objectives and features of the program are described and discussed. It is fully anticipated that these activities will help position the Teniente Technology as a world-class modem technology, well-integrated and operating in a fully continuous mode in conjunction with the other units at the plant, a competitive technology which operates in harmony with respect to environmental regulations.

Jan 1, 1999

By P. Barrios

Over a period of one year, an in-depth investigation was carried out in a conventional copper refinery to understand the behaviour of silver in copper electrolysis. The increase in silver content in the cathodes increases almost linearly with the duration of electrolysis, and the silver content of the electrolyte between the electrodes shows similar behaviour. The silver content of the cathode deposited daily depends directly on the silver concentration of the electrolyte and this, in turn, is strongly influenced by its internal temperature. The average temperature between the electrodes rises from the first to the second and to the third crop, because of the increase in the distance between the electrodes and the heat generated by the passage of the current. The mechanism of dissolution of silver from the anode, and its passage to the cathode, are discussed. Following the change to the Isa system, it was proved that the results and conclusions are analogous. Based on these results, a reduction of more than 20% in silver losses in the cathodes was achieved.

Jan 1, 1999

By L. B. Tsymbulov

At present data on thermodynamic properties of metallic melts, containing copper and ?iron family? metals, is rather limited. Determination of the activity of metallic melts components under high temperature by experimental methods requires high level of labour inputs. With this it is not always possible to obtain the results with high level of accuracy. Due to that in a number of cases it is more appropriate to apply different methods of analysis, with the help of which there can be calculated thermodynamic properties of ternary and even more complicated systems, prominent thermodynamic properties of binary systems being used as a basis for these calculations. This work presents the results of calculations of different components activity and activity ratio in such ternary system melts as Ni-Cu-Fe, Ni-Cu-Co, Fe-Cu-Co and Fe-Co-Ni. Good compliance of calculations results with those obtained in the course of reliable experimental investigations fulfilment is demonstrated. There are presented the results of activity and activity ration analysis for some compositions of Cu-Ni-Co-Fe system.

Jan 1, 2006

By John K. Wright

The segregation process involves heating oxide-type ores with a halide salt in the presence of a solid reductant. By a complex series of cyclic vapour-phase reactions, the desired metal is extracted from its original position in the ore and segregated to the vicinity of the reductant. In this form it is then amenable to concentration by physical methods. In this work the segregation behaviour or eight different nickel laterite ores has been examined using a laboratory rotary kiln. It was found that the silicate (serpentine) ores responded better to the segregation conditions used than did the limonitic ores. An examination of the segregated metal particles showed that they consisted of ferro-nickel. The concentration of nickel in the metallics was sensitive to the ore types and the segregation roasting conditions.

Jan 1, 1994

By Wang Youlai

Sichuan province is the richest province for its waterpower resource in China, perfectly suited to develop a high consuming energy industry. Sichuan Aostar Group Company has two Aluminum smelters, Guangyuan Aostar smelter and Sichuan Aostar Smelter. The production capacity of Aostar Group was 240,000 tons in 2004. The construction scale of Sichuan Aostar Aluminum smelter is 250,000 tons per year. The first 168 GY-300KA pre-baked anode cells (125,000 tons/year) were put into production in 2003. This company has taken the lead in the use of the transfer gantry technology in China. Besides making the process of calibration the pot shell it has concentrated the efforts to construct cell lining elsewhere. This company also has taken the lead in China for using the EIRICH force mixing and cooling technology as well as in the world for the CP Company?s vertical ball mill technology that produces the pre-baked anodes. The carbon anode system completed its 190,000 tons/year production scale. This is the most advanced technology and the biggest scale pre-baking anode manufacture in China. Since the Sichuan Aostar 300KA cell was put into production, it runs normally and smoothly. Up to now the current efficiency is higher than 94% and the specific energy is only 13300kWh/T-Al.

Jan 1, 2006