Search Documents

Smelter operating and environmental requirements demand high on-stream time (high reliability) from the primary smelter sulfur retention device - the sulfuric acid plant. The key to reliable smelter sulfuric acid plant operation is the gas cooling and cleaning system. Problems in the gas cleaning system cause corrosion, plugging, equipment failure, etc - plant down time, in the contact section of the plant. The last fifteen years have seen major changes in gas cleaning system design to the current standard of brick lined venturi scrubber, packed gas cooling tower with plate type liquor coolers and lead or plastic tube precipitators. The current-design offers improved impurity scrubbing along with increased reliability. In addition, a number of alternate gas cleaning systems have been offered. Chematics LAB System: Monsanto DuPont Dynawave System; Lurgi venturi scrubber with lead star gas cooler. This paper will review the design and operating advantages, disadvantages, and risk of the standard gas cleaning system and compare it to the alternate systems.

Jan 1, 1992

By Tetsuro Ohashi, Tooru Matsumiya, Yoshio Abe

"The three-dimensional deformation of a continuously cast slab was modeled into two-dimensional deformation by developing the solidified shell of the slab. The developed solidified shell was divided into rectangular elements. The thermal strain produced as the slab is wi thdrawn over one roll spacing in the casting direction was calculated from the temperature change during that time and the increment of the geometrical unbending strain during the time was calculated from the change in the radius of curvature of the slab by assuming that the neutral axis of bending is located at the mid-thickness of the slab and that the transverse section of the slab is kept in a plane during unbending. These strains were imparted to each element as initial strains. The interaction between the elements and the overall deformation of the solidified shell were analyzed by the finite element method.The analysis was performed on a slab being cast on a machine of the circular arc type with progressive unbending. The following findings were obtained as a result. The effect of unbending is spread in the upstream and downstream directions of the slab by the shear deformation of the narrow and wide faces. As the shear deformation increases, the strain in the unbending zone decreases and the strain outside of the unbending zone increases. The effects of secondary cooling conditions, slab size, radius of caster circular arc section, compression casting, etc., were also analyzed. IntroductionTo develop a method for preventing the internal cracking of continuously cast slabs, it is important to acurately analyze the deformation of the slab and this subject has been extensively investigated. Many researchers, including the present authors, have analyzed slab bulging. (1)- (11) Analysis has also been made of thermal deformation that assumes importance in continuous casting of small-section blooms.(12)-(18) However, unbending deformation, an extremely important subject for continuous casters of the circular arc type, has not been fully analyzed."

Jan 1, 1986

By Melissa L. Trapani

Keywords: Copper, Taphole, Flow Instability. ?Blister spitting? is a flow irregularity where the molten blister copper stream ? or part thereof ? sprays from the taphole exit rather than following a regular flow profile to the collection box. As well as being a general ?housekeeping? issue, the unpredictable nature of the flow is a threat to operator safety. Also, the aggressive flow pattern may contribute to the mechanical wear of the taphole refractory, compromising the integrity of the taphole. This paper brings together a collection of first-hand observations and reports from process personnel, and suggests some theories as to the causes of blister spitting.

Jan 1, 2005

By Wanderson Silva Rodrigues, Paulo Adão Marinho dos Santos, José Antonio Silva Souza, Luis Alves Venancio, Emanuel Negrão Macedo

"1 AbstractThe production of alumina from bauxite using the Bayer process generates 0.7 to 2.0 ton of the residue known as red mud per ton of alumina. This material has no large scale current use and is usually stored. This paper shows that it can be used in a suspension with water as a gas effluent cleaner with high efficiency to remove SO2. It can substitute other materials currently used reducing the overall environmental impact and potentially reducing the cost of gas treatment.2 IntroductionThe production of millions of tons per year of alumina around the world generates from 0.7 to 2.0 ton of the residue known as red mud per ton of alumina. The vast majority of the red mud is stored in large sealed lakes. Due to the high reactivity this material is considered dangerous and currently there is no operating process capable of reuse all the material produced at any refinery. These lakes after filled of solid material eventually have the surface revegetated. In any cases they will remain as an environmental passive and need monitoring for decades. The search of industrial processes that combine the cleaning of gas effluents emission and reuse of these residues can contribute to the reduction of the overall impact of the alumina production process.The main objective of this work is to study the efficiency of the red mud as alternative raw material for the control of emissions of SO2 in combustion gases. Usually this is made through alkaline solutions of CaCO3 or NaOH in absorbing equipments like spray towers or packed column. This project main objective is to study the reaction of the SO2 with a suspension of red mud and water in order to obtain the basic parameters to design equipment capable of process this reaction on a pilot scale. With that goal compositions of red mud on spray were processed with flow of gas containing SO2 with concentration similar to the exhaust gases of the combustion process of the refineries."

Jan 1, 2011

By SM Rao

Nuclear Fuel Complex (NFC ) , Hyderabad (IN DIA ) , is engaged in the manufacture of nuclear fuel assemblies and zircaloy structural components required for the Indian nuclear power reactors. The production of zirconium oxide, sponge and zircaloy materials through chemical and hydro - metallurgical processes generates many effluents containing valuable zirconium and hafnium . This paper deals with the various processes such as multiple crystalization, phosphate precipitation, ion-exchanges amine solvent extraction etc, for the treatment of these effluents and subsequent recovery of valuable zirconium and hafnium .

Jan 1, 1992

By Kim Fagerlund

Boliden Harjavalta Oy operates a copper smelter in Finland, which is based on flash smelting together with Peirce-Smith converting of copper matte. This paper reviews a case study when a high arsenic feed mixture was successfully eliminated in order to guarantee the anode quality. Based on theoretical and practical knowledge in slag chemistry at Outokumpu Research, the CaO-fluxing practice was introduced. Description of a thermodynamic simulation using MTDATA and implementation of the results into converting practice is given. Results showed that the impurity fluctuations in raw materials could be effectively controlled by efficient utilization of different slag chemistry.

Jan 1, 2005

By Thomas Weyand, Thomas Claridge, Dale Nickels

"This paper addresses the initial results of a project to evaluate the suitability of copper mining tailings as raw material for the production of structural products using PMET’s patented technology. Preliminary testing indicated that high performance structural products were possible using these materials. A demonstration scale project produced approximately 1,500 bricks in various colors. These products fall under under ASTM C- 73 and were found to present properties suitable for severe weather applications. Although the products in this project were of typical brick dimensions, other products are possible, for example concrete block substitutes or pavers. These products from the PMET process are commercially known as Brixx. This paper will provide operational details of the production process, mineralogy and mechanical properties of the products.INTRODUCTIONPMET has developed process technology that can convert various siliceous waste materials into competent structural products. This technology is the subject of US patent # 6,068,803. In general, the process consists of mixing lime, water and the major feed stock, pressing to form a “green” shape, and curing the product in an autoclave for 6 hours with saturated steam at ~200oC. The curing process forms Tobermorite, which acts as a crystalline binder. Freeport-McMoRan approached PMET to see whether mine tailings from the Sierrita mine, containing significant amounts of clay, might be a suitable feed material for the production of structural products. “Brixx” is the commercial term used to describe the resultant structural product formed in the test work. This paper is a preliminary evaluation of a technology that is being considered by Freeport-McMoRan. This report is not an endorsement by Freeport-McMoRan of the process or products, nor is it a commitment to use this technology."

Jan 1, 2008

By C. G. Bastos Andrade, V. F. Justo, F. R. Valenzuela-Diaz, M. G. S. Valenzuela, C. M. Matos, C. Volzone

For industrial use, the smectite clays are usually treated with inorganic acid of high concentration at temperatures under boiling point, which provide the bentonite´s bleaching power. In the present paper, a sample of brown smectite from Paraiba, Brazil, was submitted to treatment under moderate conditions (90°C, reaction times of 1, 6, 12, 18 and 24hours in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5M, clay/acid solution ratio of 1g/10mL), aiming to reduce impurities, responsible for the color of the clay, without causing significant changes in their structure. The samples were characterized by scanning electron microscopy (SEM), energy dispersive X-ray detector (EDS), stereomicroscopy, Cation Exchange Capacity (CEC), Thermal Analysis (TG/DTA), and X-ray diffraction (XRD). It was observed a bleaching in samples with time of 12h to 18h. With the DRX was possible to monitor the peak intensity of the clay structure and the sample with 12 hours of treatment was not significantly altered its crystalline structure, maintaining the peak clay at d(001). The most pronounced changes in the bleaching occurred within the first 12 hours of acid treatment. Thus, clay can be used in products with high added value.

Jan 1, 2015

By S. G. Kumar, R. G. Reddy

"Niobium aluminides offer the advantage of higher high temperature capability compared to other intermetallic aluminides due to the refractory nature of niobium. However, the reaction sequence in Nb-Al system is sluggish and currently there is a great interest in the processing aspects of these materials. In the present study, a systematic investigation was undertaken to compare the effect of different powder metallurgy processing routes on the phase relations and microstructure of 66Nb-22AH2Ti (in atom percent) alloy. The three different process routes adopted were: (i) cold pressing followed by reaction sintering; (ii) cold pressing and hot pressing followed by sintering; and (iii) arc melting, hydride-dehydride process to make the alloy powder followed by cold pressing and then sintering. The samples are analyzed by XRD, Optical Microscopy, SEM-EDS and EPMA. The analysis showed that alloy pellets made from pre-alloyed powders i.e., arc melting followed by hydride-dehydride process, gave good densification and more Nb3Al formation.1. IntroductionTo improve the performance standards of turbine engines, materials scientists are challenged to develop materials that have· high thrust-to-weight ratio with high specific strength, high specific modulus and good environmental properties at elevated temperatures. The conventional high temperature materials like nickel based superalloys are high in density and hence many of the high temperature materials scientists have focussed their attention on intermetallic aluminides like Fe-AI, Nb-AI, Ni-AI and Ti-AI in recent years. The phase relations and properties of alloys based on Fe-AI, Ni-AI and Ti-AI are fairly well known whereas little is known about the alloys based on niobium aluminides."

Jan 1, 1996

By J. Antrekowitsch

Keywords: residues, fluorides, chlorides, zinc, steel mill dust The recyclability of various nonferrous metal wastes often suffers from a relatively high fluorine and chlorine content. Both are inserted in most cases by the use of plastic contaminated scrap and a wide variety of different coatings. These halogens lead to poor product qualities and off gas contamination. Especially the history of zinc recovery from steel mill dusts shows, that the today common hydrometallurgical options are on their limit and therefore are not sufficient in most cases. This thermochemical study should give more information about different pyrometallurgical options, that offer both a chlorine and fluorine reduction and efficient zinc recovery, preferably in one process step. Selective evaporation in different atmospheres and conversion with the use of hydrogen are the main parts in this study. The results combined with the relatively small information available from literature should provide a basis for further investigations in this field.

Jan 1, 2005

By Hiroyuki Matsuura

The effects of P20S or Na20 addition on the reaction rate of CO2 dissociation on the surface of FexO-base molten oxides was investigated at 1773K by isotope exchange methodl-6_ The rate constant decreased with increasing P20S content of molten oxides and the residual rate constant was observed at high P20S content On the other hand, the rate constant increased with increasing Na2O content for FexO-SiO2 melts. The rate constant was evaluated by the composition of oxides and the rate controlling step of CO2 dissociation was discussed.

Jan 1, 2003

By Scott A. Shuey

Keywords: E-Waste, Pyrometallurgy Many might think addressing the issue of e-waste is a new area of study. Electronics disposal has been discussed in some circles for at least the past 25 years. The recycling of electronic waste (e-waste) tends to be a rather complex undertaking when considering the intimate bonding of materials in the average printed circuit board. The development of a recycling process is further complicated when considering the wide variety of products being generated under the heading of ?electronics.? Focusing only on the primary constituents (polymers, Cu, Al, Fe, etc.) tends to lead one to fairly simple flowsheets. Ignoring trace elements, and the various halide species generated, will lead process engineers down a development path that is sure to cause material handling issues. Researchers at Colorado School of Mines are modeling the complex chemistry that exists within the body of e-waste?comprising 39 of the known elements. An understanding of the systems thermodynamic behavior will result in the development of a more robust, long-term process for the recovery of valuable materials from the e-waste stream.

Jan 1, 2005

By Ram V. Ramachandran

As an industry with major potential impacts (both good and bad) on water resources and due to the rising costs of process water, the mining and metallurgical processing industry has a key responsibility to contribute to the overall goal of preserving both the quantity and quality of water available within the watersheds they operate in. As we plan for new and existing mining and metallurgical projects, we need to consider a hierarchy of options to minimize our impact within the watersheds we operate; keeping clean water clean by diverting around our operations; reduction in the amount of water we use; reuse of water wherever possible, and improvements to water quality for recycling and/or release to environment. Technology is needed to treat water to improve its quality for reuse or release to the original watershed. While lime precipitation followed by sulfide polishing is effective for removal of most of the metals, it does little or nothing to remove ammonium ions and anions such as chloride, nitrate, molybdate, arsenate and selenite/selenite. Regulations on sulfate limits in treated discharge water has drawn close attention to the treatment of acid mine drainage (AMD). Management of brine and salt disposal is also posing a problem due to strict regulations and cost of disposal. This paper will: (a) address issues associated with managing water with the objective of maintaining water sheds—status quo-during and after operation (b) discuss potential technologies for advanced water treatment plants.

By Chen Song

Keywords: Mixed extractant, Copper, Cobalt, Nickel, Synergistic effect During separation process of copper and cobalt from nickel sulphate solution, the effects of constitutions and compositions of mixed extractant D2EHPA and PC88-A or Cyanex 272, has been studied. In one step extraction cycle, the following results are obtained:[Ni]/[Co]>4000 and [Ni]/[Cu]>40000 in nickel sulphate solution, [Co]/[Ni]>1000 and [Co]/[Cu]>30000 in cobalt chlorinate solution, [Cu]/[Ni]>10000 and [Cu]/[Co]>200 in copper sulphate solution. It was elucidated that the above-mentioned synergistic mixtures can effectively separate cobalt and copper from nickel sulphate acid solution and achieve a greater synergistic effect.

Jan 1, 2005

By Adam Powell, Salvador Barriga, Matthew Earlam

"The inert anode is a key enabling technology for dramatic energy and emissions reduction in extractive metallurgy. In molten salts, the materials challenge is nearly insurmountable: the anode must conduct electrons at high temperature in a pure oxygen and molten salt environment. A solid electrolyte, e.g. zirconia, between the salt and anode removes the molten salt stability constraint, and can act as a container for a liquid metal anode. This can be liquid silver for oxygen-generating inert anodes, or several metals for natural gas-fueled anodes; it is possible to switch between these modes. The solid electrolyte brings several other benefits: it eliminates molten salt contamination of the anode gas, creates a reducing environment enabling low-cost steel vessels, increases current efficiency, and eliminates carbon contamination of the product. New developments presented here, including current collector and low-cost anode designs, amplify these benefits for producing aluminum, magnesium, rare-earths, and other metals.IntroductionReactive metals such as magnesium, aluminum and rare-earths play increasing roles in efficient transportation and clean energy. In response to new fuel economy standards, automotive OEMs are planning large increases in use of aluminum and magnesium to reduce vehicle weight. Rareearth permanent magnet motors and generators exhibit better power-to-weight and efficiency than induction motors and other designs, making this today's primary motor technology for hybrid and electric vehicles, and for wind turbines. Nickel metal hydride (NiMH) batteries with lanthanum are dominant in hybrids. In 2011, transportation comprised 28.6 out of 103.1 EJ of US energy consumption [1] and 1,845 out of 5,471 million metric tonnes (MMT = 109 kg) CO2e of US greenhouse gas (GHG) emissions [1], creating big targets for economy-wide reductions.Unfortunately processes for making reactive metals for these applications are very inefficient and heavily-polluting. In primary aluminum production, Hall-Heroult cell electricity use [2] is more than double the reaction enthalpy due to heat losses through frozen cryolite side-walls and anode gases, graphite anode plants add significant energy use and GHG emissions [2] (see Table 1). Magnesium is even worse: silicothermic reduction by the Pidgeon process in China produces about 85% of the world's magnesium using coal or coke gas [3]. Chloride electrolysis begins with high-purity MgO and requires carbochlorination or hydrochlorination and costly chloride dehydration [4]—rendered unnecessary for aluminum by the Hall-Heroult cell. Production of neodymium and lanthanum with graphite anodes leads to inconsistent carbon content: small cells make 1 kg batches for analysis, sorting and sale by carbon content, with very high labor and analysis costs. And vertical electrodes give no incentive to reduce anode effect: some reports indicate that China's rare-earth metal industry emits more CF4 and C2F6—with global warming potential (GWP) 6500 and 9200 times CO2 respectively—than China's aluminum industry [5]."

Jan 1, 2014

By T. J. White

Each year, thousands of tons of toxic concentrates are produced as the unwanted byproducts of industrial operations and smelting activities. The fate of these materials remains open, as in general their consumption is limited and potential markets contracting. Xtaltite (pronounced crystal-tight) is a Synthetic Mineral Immobilization Technology (SMITE) optimized for the concentration, detoxification and consolidation of toxic metal wastes. In this approach, we seek to mimic nature to produce durable synthetic minerals that survive for aeons in well characterized geological settings. This approach has high public acceptability because the concept is easily understood by the layperson and the long term stability of the waste form may be predicted with confidence. In addition, where Xtaltite is used for mine backfill, a system of ecologically sustainable mining development is established. This paper details the design and fabrication of Xtaltite under oxidizing and reducing conditions. To illustrate and contrast these stabilization regimes, specific reference will be made to the treatment of thallium, chrom~um and arsenic wastes. Waste form performance under TCLP, dynamic boiling water tests and in other leaching media will be compared and discussed with respect to their relevance to different disposal options.

Jan 1, 1995

By Carlos Antonio da Silva

Steel refining reactors based on chemical heating are being used as an alternative to ladle furnaces. They show a high degree of flexibility in respect to heating rate in addition to carrying out refining reactions such as de-S, inclusion removal, alloying etc. IR-UT and CAS-DB are examples of such reactors. Their performance is dependent upon geometrical characteristics as well as operational conditions which determine the flow field inside the vessel. A physical model of the IR-UT process of the Companhia Siderurgica de Tubarao, steel plant located in Serra, Espirito Santo, Brazil, was developed to assess the features of the flow field and its influence on the metallurgical behavior. Results of the physical model were used to optimize the process parameters in the industrial unit.

Jan 1, 2003

By Carlos Antonio da Silva

Steel refining reactors based on chemical heating are being used as an alternative to ladle furnaces, They show a high degree of flexibility in respect to heating rate in addition to carrying out refining reactions such as de-S, inclusion removal, alloying etc. IR-UT and CAS-OB are examples of such reactors. Their performance is dependent upon geometrical characteristics as well as operational conditions which determine the flow field inside the vessel. A physical model of the IR-UT process of the Companhia Siderúrgica de Tubarão, steel plant located in Serra, Espirito Santo, Brazil, was developed to assess the features of the flow field and its influence on the metallurgical behavior. Results of the physical model were used to optimize the process parameters in the industrial unit.

Jan 1, 2003

By D. P. Cook, M. I. Bloch, J. A. Dantzig

"In this article, we describe a combined experimental and computational program to study the filling of automotive wheels during low pressure die casting. Experiments are performed by placing thermocouples into the mold walls of a production caster for the Ford F 113 wheel to measure the temperature profiles in the die during processing, and to infer the filling pattern. Computational models are also developed using a 36° section of the wheel pattern, taken directly from CAD data files. We use these models to simulate the filling and heat transfer processes. Comparison between experimental and computational results are presented, demonstrating the viability of this procedure.IntroductionAutomotive companies are using increasing amounts of aluminum in production vehicles: While the main driving force is improved fuel economy through weight reduction, replacing steel wheels by aluminum also offers the potential for improved vehicle performance by reducing unsprung mass. For these reasons, many new vehicles are now supplied with cast aluminum alloy wheels, and the aftermarket for these wheels continues to grow.The most common production process for these wheels is low pressure die casting. The process is subject to numerous defects, including microporosity, cold shuts, cold folds, misruns and inclusions. Scrap rates at the caster of the order of 10% are not uncommon. Many wheels also have large production runs, into the hundreds of thousands of wheels per year. Thus, the cost savings from even small reductions in scrap rate have the potential to be quite significant.Most of the defects are associated with the filling and solidification processes in the mold. The molds are air cooled, and the placement and sizing of cooling passages is currently as much art as science. The ultimate goal of this project is to improve that situation, by implementing simulation procedures that enable engineering design methods to be used in die and process specification."

Jan 1, 2000

By Chris Twigge-Molecey

As emission constraints for metallurgical plants become more difficult to meet; control of major, multi-vessel, flue systems become more critical. Control instabilities can result in significant loss of system capacity or emissions to the environment. This paper will discuss the use of dynamic simulation techniques to optimize both the design and control strategies for these systems. A significant ,safety hazard is associated with pressure excursions from process upsets or equipment failures. Pressure rise rates of up to 10 kPajsec can occur. These cannot-be followed by conventional controls. Fail-safe high speed venting is required to protect both the furnaces and operating personnel'. Design options, sizing techniques and practical problems are discussed.

Jan 1, 1992