Search Documents

By Józef Czemecki

Polish copper concentrates are characterized by high levels of impurities, particularly Pb and As. Two technologies are being used for copper concentrate smelting at KGHM Polska Meidz S.A., namely the shaft furnace process (Legnica Copper Smelter, Glogów I Copper Smelter) and a single-stage process for direct to blister concentrate smelting in a flash furnace (Glogów II Copper Smelter). Both technologies are used at different physical and chemical conditions which results, in different impurities behavior. The paper presents flow sheets for copper production in a plant using the shaft furnace process and in another in which a single stage flash process is used. The metals distribution in particular semi-products is given as well as a method for elimination of impurities from the copper production cycle. Methods are also discussed for alloy and matte converting and copper refining to obtain low Pb and As concentrations in anode copper (0.3% Pb and 1500 ppm As maximum) that are being used in the KGHM Polska Meidz plants. Useful co-operation between the plants using different technologies, aimed at the limiting the effect of undesired impurities on the quality of blister copper produced, is also described.

Jan 1, 1998

By P. M. Rosário

The extraction performances exhibited by a phosphoric (D2EHPA), a phosphonic (Ionquest 801), a phosphinic (Cyanex 272) and a dithiophosphinic (Cyanex 301) acid derivative towards indium recovery from a diluted sulfuric solution are evaluated and compared. Equilibrium extraction isotherms were obtained. The chemical reactions involved and the approximate stoichiometry of the In(III) extracted species by the four ligands are presented and discussed. Stripping of In(III) from loaded D2EHPA and Ionquest 801 has been accomplished successfully, but has not been so effective from loaded Cyanex 301. Plots of %E vs. pH were established for D2EHPA, Ionquest 801 and Cyanex 301, denoting their behavior towards the extraction of similar mass concentrations of In(III), Fe(III), Fe(II) and Zn(II). Cyanex 301 is the least selective towards In(III), whereas D2EHPA and Ionquest 801, both for a pH = 0.5, do not extract Zn(II) at all.

Jan 1, 2003

By D. M. Hausen

Microscopic point-counting of polished sections, in combination with x-ray diffraction analyses of representative whole rock samples, provides an efficient means to compare the modal mineralogic composition of different rock types. Major gangue minerals, e.g., quartz, feldspars, micas, amphiboles, chlorite, clays, etc., are estimated semiquantitatively by x-ray diffraction techniques, utilizing optimum grind, gridded sample surfaces and a sample spinner during scanning. Opaque to semi-opaque oxide and .sulfide phases are estimated by microscopic "point-count" and "gross-count" scanning. Total mineralogic compositions are calculated and normalized to 100 percent from XRD and microscopic data by computer programming. Comparative mineral analyses for different rock types, as well as quantitative microscopic data for various parameters, including particle and crystal sizes, textures, degree of alteration, paragenesis, etc., provide useful guides in mineral exploration, both in early stages of geologic mapping and later stages of economic evaluation. Several case histories are described.

Jan 1, 1981

By Yungang Li, Hui Li, Ramana G. Reddy, Jinglong Liang

High solid corrosion protective coatings were prepared by the dust of the converter with an average particle size of 59.33 μm. The effect of different amount of benzyl alcohol diluent on the performance of high solid anti-corrosion coatings was studied. With the increase of the amount of diluent, the viscosity of high solid anti-corrosion coatings reducing, the film apparent bubble content decreasing, and film resistant to salt water corrosion ability decreased, while acid corrosion capacity enhancement. When the dosage of diluents is 15%, the coating film is more resistant to acid corrosion.

Mar 1, 2017

By J. B. Winter

The present Inspiration Consolidated Copper Company Smelter/Acid Plant complex located near Miami, Arizona, was designed and built specifically to conform to the ambient air quality standards imposed by the Federal Clean Air Act of 1971. The present plant replaced a facility which had been in operation since 1915. The electric furnace, siphon converters and acid plant complex were commissioned in May, 1974 (1). At that time, the Plant was considered to be one of the most extensively monitored and instrumented facilities of its kind in the world. Several control areas were located in close proximity to the controlled process, in addition to so-called central control rooms in the Smelter and Acid Plant. The control rooms were staffed with officials below the foreman level. Instrumentation consisted of conventional analog devices, except for a computer used in monitoring ambient air environmental conditions and limited use of programmable logic controllers. The harsh service conditions prevalent in the plant rendered a significant portion of the instrumentation unreliable and, in many cases, inoperable. Failure of the facility to obtain the total sulfur collection for which it was designed was, in part, due to serious inadequacies in control system logic and sulfur recovery averaged 79% in the early years. After careful study of the smelting process, engineering hardware and high labor cost inherent in the organizational structure, management made a judgement decision to convert to centralized control of the process with high level supervision 24 hours per day. A distributed digital control system with supervisory arid data acquisition/information reporting computers was selected to satisfy the requirement of central control. Operations are now controlled and coordinated from a primary control room in the Smelter and a satellite control area in the Acid Plant.

Jan 1, 1983

By George Oprea, Tom Troczynski, Joe A. Rigby, Waiman Lo

The refractory lining of the tuyere line in Peirce Smith converters have usually much shorter life in service than the rest of the lining, above or below it. There are already recognized chemical, thermal and mechanical factors which contribute to the wear of the lining. Our study presents the experimental results on microstructural changes occurring on these tuyere line bricks in a nickelcopper converter. The experimental bricks, after use at the tuyere line, were investigated using SEM/EDS and XRD techniques, to identify the mineralogical changes due to interactions with the nickel-copper matte or fayalite type slag at the process temperatures. The microstructural changes were correlated with physical and mechanical properties of the brick before and after use and a wear mechanism was suggested. Although the matte does not theoretically react with the mineralogical components of the brick, a partial oxidation of the Ni-Cu sulphides was identified using a line analysis by SEM/EDS in the densified layer at the hot face, which allows for mineralogical changes at the matte-refractory interfaces, with a high probability of microcrack formation due to the thermal cycling during use. These microcracks were also identified to open through inter-granular fractures parallel to the hot face, which appeared to be the main cause of lost lining during use. The reactions between the fayalite slag and refractory brick could eventually play a role in chemical dissolution of the brick only in the superficial layer at the hot face, as no slag components were identified deep into the brick.

Jan 1, 2009

A modified Cuprex Metal Extraction Process (CMEP) leach process was used to extract Cu. Ni and Co from a complex sulphide concentrate. The standard leach was modified to a two-stage countercurrent leach which provided emf control of the copper SX feed and minimized iron dissolution. A flowsheet was developed to recover the base metals and silver from the leach solution and gold and platinum group metals from the leach residue which was predominantly elemental sulphur. Techniques required to maintain an iron balance in the system including pressure oxidation and solvent extraction are described.

Jan 1, 1996

By E. vanHuyssteen

A method of establishing the relationship between the mineralogy of a sinter and its subsequent processing behaviour in a lead blast furnace is demonstrated. It involves: 1) analyzing the Zn-spinels, hardystonite, larsenite, Pb-silicates, Pb-arsenates, Pb-(Ca)-sulphates and other femtes with an electron microprobe; 2) determining the extent of elemental substitutions in various mineral structures; 3) establishing a sequence in which the various phases formed during sintering. In this manner the relationship between the bulk chemistry of a sinter formulation and the speciation of elements into various phases in the sinter can be established. Specifically, the-substitution of Mg for Zn in hardystonite significantly influences sinter production. Mg substitution releases Zn into the surrounding matrix. This Zn reacts with the Pb-silicate to form larsenite thereby reducing the amount of Pb-silicate available for anhydrite digestion. Excessive amounts of residual anhydrite thus result if the sinter formulation is based solely on the CaO/Si& ratio.

Jan 1, 1993

By J. R. Donald

Surface and interfacial phenomena play a significant role in refractory performance. For example, the wettability of the refractory material with slag, matte, and metal influences infiltration and interfacial reactions. Yet, very little fundamental information regarding the surface properties of refractory materials and slag is available. Thus, in the present work, the sessile drop technique incorporating a high temperature furnace equipped with X-ray fluorescope was employed to investigate the surface and interfacial phenomena of fayalite-type slags on solid alumina at 1200?C. The iron to silica (Fe/SiO,) ratios employed were 1.4 and 2.0, and the oxygen potentials used were log p02 =-11 and log p02=-9 atmospheres. The contact angle between the fayalite-type slags and the alumina were determined to be relatively low, at about 16.9 to 19.6 degrees under the experimental conditions. The surface tension of fayalite slag (Fe/SiO2=1.4) at an oxygen potential of log -11 was 0.298, which agreed with the work of previous researchers. The surface tension of the fayalite was observed to increase with time. The spinel FeAl2O4. was determined to be the product of the interfacial reaction, and 8.8 to 15.8 mass percent alumina was dissolved into the slag after 40 minutes.

Jan 1, 1996

By F. H. A. Abdalla

A process is described for the recovery of valuable nonferrous metals from steelmaking dust by suiphatizing roasting using ammonium sulphate. Maximum recoveries of soluble metal sulphates achieved at optimum conditions were> 99.0 %. Selective metal separation of the soluble sulphates in the leached liquors were performed either by controlling the roasting temperature or by adjustment the pH values of the leached liquor ranging from 3.6-6.2. Either pure zinc oxide orland tin oxide could be obtained at optimum conditions, and the products were evaluated chemically and by X-ray analyses. The residues rich in iron oxide can be removed and recycled. The mechanism of sulphatizing roasting process was considered. A general flow-sheet for the overall process of treatment the steel making dust to recover its valuable nonferrous metals was suggested, which ca be applied for other nonferrous bearing materials.

Jan 1, 1996

By Djalma Souza, Felipe Perissé Duarte Lopes, Frederico Muylaert Margem, Sergio Neves Monteiro

The development of composite materials is a combination of distinct materials, with applications in various areas, such as: aerospace, automobile, etc. Regardingmechanicalresistance,composites reinforced with a dispersion phase in a fiber form is more relevant. The green idea is use composites with natural fibers instead offiberglass, especially in non-structural applications. The Fique fiber has occupying an important place at Colombian agricultural and agribusiness sectors. Epoxy matrix composites reinforced with 1–6 Fique fabric layers were tested and the results indicated that thetensile properties improve with increasing theamount of Fique fabric layers. The fiber/matrix interaction was analyzed by scanning electron microscopy.

Mar 1, 2018

By Hazoor Singh Sidhu

Materials degradation due to corrosion is the major problem in power generation equipment, gas turbine, fluidized bed combustion, industrial waste incinerators etc. Some super alloys have been developed, but they are unable to have different properties to meet the demand of today?s industry. Therefore, a composite system of a base material providing the necessary mechanical strength with a protective surface layer different in structure and/or chemical composition can be an optimum choice in combining material properties. Thermal spray coating of the components before they put into service by suitable surfacing alloy and with suitable coating method can increase the life of these components several fold. Choice of right coating method and alloy for a particular application is extremely important to get the desired service life. The corrosion of some materials and the role of HVOF thermal spray coatings to counteract the same have been reviewed, with an aim to understand the phenomena along with various applications.

Jan 1, 2006

By Natasa Mitevska

In order to ensure the minimal copper concentration in the reverb furnace slag, the graphical optimization method is used and the optimal slag composition of the reverberatory furnaces No.1 and No.2 in the RTB BOR, Copper Smelter and Refinery (Serbia) is obtained: (Si02) .. 38.0%; (FeO) .. 40.0%; (Fe3O4) = 5.0%; (CaO) = 5.0%; (Al2O3) .. 6.0%. Keywords: Optimization, Reverb Furnace Slag, Graphical Method

Jan 1, 2003

By Judy Che, Steven Ceccio, Gretar Tryggvason

"A detailed understanding of drop deformation and solidification is essential for quantitative predictions of geometry and properties of parts made by ballistic particle manufacturing processes. Axisymmetric results of towers built by the deposition of multiple drops are presented. In these computations, fluid flow, heat transfer, and phase change are fully coupled throughout the drop deformation and solidification process. The solution method is based on a single set of conservation equations written for all phases simultaneously. The phase boundaries are treated as imbedded interfaces by adding the appropriate source terms to the conservation equations. A parameter study demonstrates the effect of Weber number, Peclet number, and drop deposition frequency on the final shape of the structure. Numerical results show that most successful method of building uniform towers is when two conditions are met. First, each drop solidifies at the same time in the deformation cycle. Second, the cooling rate is slow enough to allow for good adhesion between drops. The ability to predict the final shape of deposited drops will greatly reduce the amount of experimentation necessary to select the desired set parameters for any artifact.IntroductionMaterial deposition techniques based on layering small molten metal drops holds the promise to build small, coherent three-dimensional structures. In this process, numerous 20-100 µm diameter drops are deposited onto a substrate with a low impact velocity (on the order of 5 mis). Both the momentum and trajectory of each drop are controlled precisely to build up complex parts. This material layering technique differs from processes such as spray forming and splat quenching which involve high impact velocities (on the order of 100 mis) and high frequency deposition with little control over individual drop placement. This process of layering small drops can produce parts with near net shape accuracy, while spray forming produces slabs of material which must then be worked to make a usable part. The ability to computationally predict final drop shape and cooling rate has the advantage of allowing the user to select parameters to produce parts with desired shape and mechanical properties. However, the development of such predictive methods requires a thorough understanding of both drop deformation and solidification"

Jan 1, 1999

By Mark Cross, Andrew P. Campbell, Koulis A. Pericleous

"Computational Fluid Dynamics (CFD) modelling is being used to simulate the freeze layers formed within direct smelting processes. There has been some concern whether water-cooled elements can withstand the p~ocess conditions and in particular abnormal cases where they may be splashed in molten metal.To validate the models being developed, two cases from literature have been modelled for solidification and stress analysis. The solidification case is presented in detail and is for hot molten metal flowing through a cylindrical pipe. The walls are at a temperature below the melting point for the metal. The resulting solid (or freeze) layer is within 3% of the value calculated by Sampson & Gibson9 •Preliminary modelling of the refractory-slag interactions is presented. Although three basic mechanisms: Penetration; Corrosion; and Erosion will eventually be modelled, only the penetration is considered here. The corrosion mechanism is to be modelled by tracking the time that the penetrated refractory is at the required temperature.Future work, after adding all the required physics, will focus on the modelling of a water-cooled element placed lower in the smelter. Process perturbations will be simulated to examine what these elements will withstand."

Jan 1, 2001

By John Wallace

"Monitoring compound semiconductor crystal growth using multifrequency eddy currents for sensing illustrates some of the extreme problems of measurement and interpretation that are not often seen in metallic systems. Using sensor arrays and scanning sensors have produced a qualitative and quantitative understanding of some of the high temperature electrical conductivity mechanisms in several compound systems. A detailed review of the CdTe/CdZnTe data is presented showing some of the complexity in the data as opposed to what is found in elemental semiconductors.HistoryThe most common goal in the use of eddy current measurement in crystal growth is to deter-mine the curvature of the liquid solid interface during growth to test if the heat transfer estimates of the thermal design were adequate for single crystal growth[l]. This aim could be met but represented only a small fraction of the data that was produced observing a growth cycle. A secondary consideration was what could be discovered in the recorded data about the growth and subsequent heat treatment as the boule cooled. This is usually a more difficult task because a crystal growth process is not a controlled experiment so much as a process that continually sees modification. Using a sensor arrays or a scanning loop has produced a qualitative and quantitative basis for understanding some of the high temperature electrical conductivity mechanisms. The implication of the these measurements of electrical conductivity variations are important in that they reflect the complex defect states that will occur on cooling and heat treatment following crystal growth. In contrast to the complex behavior of the conductivity of these compound semiconductors in the solid and liquid state we have the very well characterized system silicon to compare. Initially the interest on using eddy currents to monitor compound semiconductors came from G. Westphal at the Texas; Instruments Company in 1987 to monitor aspects of growth and compounding of GaAs. This was followed by work on solution growth of HgCdTe with D. Witter. The initial interest in the use of eddy cur-rents for monitoring CdTe crystal growth came from Prof. Wilcox at Clarkson University in the practical interest to determine and control the crystal interface curvature during vertical brigdeman growth. The first actual work was done by one of his former students. G. Neuge-bauer at the II-VI Corporation which was carried on by G. Rosen at Clarkson and R. Shetty at II-VI Corporation and with A. Socha at Johnson-Matthey Electronics. The work on CdTe extends over four years and yielded sufficient data to allow one to evaluate the utility of the information produced as compared to what could be obtained from monitoring an elemental semiconductor such as silicon."

Jan 1, 1997

By Mehmet Bu daycı, Onuralp Yücel, Ahmet Turan, Murat Alkan

In this study, iron based alloys (Fe, Fe-Cr-Ni-Mo, etc.) were produced by using metallothermic methods starting from Mill Scales obtained continuous casting processes. During the process, the combustion was realized by ignition and the produced wave propagates throughout the reactant mixture yielding the desired product. In this work, Mill scale used as an iron source, which includes +2, +3 values iron oxides. Aluminum, Magnesium and Silicon were used as reductants. In these metallothermic experiments, different ratios of reductants were examined, and their effects on the metal recovery and alloy compositions were investigated. The samples were characterized by using chemical analysis (AAS), XRD and XRF techniques.

Jan 1, 2016

By Zhonglin Ye, Yifeng Shi

"This paper has outlined forms of Au & Ag losses in copper smelting process and methods for increasing Au & Ag recovery, analyzed factors influencing Au & Ag recovery in copper converting process, presented Au & Ag behavior in copper electrorefining process, and reviewed effect of current density/electrolyte circulation rate during electrolysis and surface finish of cathode on Au & Ag losses. Measures and research direction for decreasing Au & Ag losses in electrolysis have also been introduced. Based on Au & Ag behavior in copper electrorefining process and previous studies by others, new approach for increasing Au & Ag recovery in copper smelter has been discussed. And brief comparison has made between continued multiplication method and equilibrium method application in the case of calculation of Au & Ag recovery in copper smelter.IntroductionAs gold and silver are the major by-products from copper smelting process, efficient Au & Ag recovery has become one of the key approaches for copper producers to increase economic efficiency. With similar physicochemical properties, Cu, Au and Ag belong to the first subgroup of elements in the same periodic table. Au and Ag will be enriched into Cu phase firstly when both matte-slag phase and copper-matte phase appear in copper smelting process. However, great changes have taken place in Au & Ag proportions into individual phase due to changes of physicochemical conditions in each smelting process. Metallurgists at home and abroad have carried out a great deal of pilot plant tests and laboratory tests in order to increase Au & Ag the former Soviet Union with regard to Au & Ag losses in copper smelting process in the 1970s and 1980s, and he proposed solutions to increase Au & Ag recovery in copper metallurgical plants. As more than 20 years passed, Jingchun Lu's paper, Discussion on Increasing Au & Ag Recovery in Copper Smelting System, remains as a literature of the most comprehensive study. Based on Jingchun Lu's literature, the authors of this paper discussed new approaches to increase Au & Ag recovery in copper metallurgical plants with combination of many researches done by other researchers for over 20 years."

Jan 1, 2013

By Vladimir Panjkovic, Ostrovski. Oieg, Campbell Cripps Clark, John Truelove

"Effects of properties of raw materials and blast on the performance of an iron bath reactor have been examined by a mathematical model. The model consists of three modules: 1) chemical reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, post-combustion ratio and heat-transfer efficiency, temperature and composition of the off-gas, and slag and metal chemistry.IntroductionOne of the anticipated advantages of smelting reduction over conventional ironmaking is the use of lower-grade raw materials. In this work, the effect of-properties of raw materials on the performance of an iron-bath reactor is examined with a numerical model. The model is also used to assess the effect of properties of the blast (flowrate, temperature and oxygen enrichment) and ejected droplets (generation rate, size and ratio of total weights of slag and iron droplets) on the key parameters of the process. In the process coal, oxygen, ore (which may be partly prereduced) and fluxes for specified slag composition are charged to the bath. Slag and iron droplets are ejected from the bath into the gas phase, where they are heated before returning to the bath. Iron droplets undergo decarburisation and reoxidation with CO2 and H2O. Dust is also generated from the bath, and oxygen or preheated air for post combustion is injected from the top of the vessel.The model consists of three modules: 1) reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The structure of the model and the data exchange between the modules are shown in Fig. 1. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, postcombustion ratio (PCR), heat transfer efficiency (HTE), off-gas temperature and composition, slag and metal chemistry, and rates of decarburisation and reoxidation of the iron droplets."

Jan 1, 1996

By Mei-le He, Min Chen, Xiang Shen, Lei Xu, Lei Liu, Nan Wang, Xue-liang Yin

In the current study, Al2O3-MgO-CaO refractories were prepared at 1400-1600 by the addition of MnO micro-powders, and the effect of MnO addition on densification behavior of the refractory was discussed. The results showed that the doped MnO dissolved to MgAl2O4 phase, and promoted the growth of MgAl2O4 grains by the formation of MgAl2O4 solid solution. As a result, the dense microstructure was obtained, with the apparent porosity decreased from 19.2% to 5.4% and the bulk density increased from 2.78g/cm3 to 3.15g/cm3 after firing at 1600 for 2h by the addition of 4% MnO. In addition, a texture microstructure was observed, which is considered to be favorable to improve mechanical properties and the service life of Al2O3-MgO-CaO system refractories.

Jan 1, 2016