Search Documents

By Richard I. Barnhisel

At the Sinclair Study Site it was found that the deeper the soil the greater the yield of corn, soybeans, wheat, alfalfa, and timothy. Yields at this location were generally lower than those at the Alston Surface Mine. At Alston the non-prime land treatments generally produced greater yields for all crops than did the prime farmland treatments, however, the intermediate soil thickness, 20 cm topsoil over 40 cm of subsoil, gave the best yields, provided it's subsoil had been limed. From a chemical point of view, acidic spoils do not need to be buried by 120 cm or 4 feet of soil, provided adequate lime is applied to these spoils as a barrier prior to placement of good quality topsoil and only forage crops are to be grown. The burial depth must be increased to as much as 75 cm when grain crops such as corn or soybeans are to be grown. This response to burial depth appears to be related to water storage needed by the crop and not due to toxic effects of the spoils. A conventional farm tractor-mounted subsoiler increased yields of soybeans and corn the first one or two years, but the effect was diminished with time. Subsoiling did not produce significant increases for alfalfa or wheat. However, ripping with a bulldozer produced significant yield responses, especially for corn and soybeans, that have lasted for at least three years. The ripping effectively reduced the bulk density at least within the zones through which the ripper had passed. Liming the upper 20 cm of subsoil significantly increased yields of alfalfa, corn, and soybeans. There also appeared to be an interaction between this lime treatment and soil depth. Yields of some grain and forage crops may be high enough to meet target levels for bond release for prime farmland. Based on the present study, one should not expect corn yields to be high enough to meet bond release. This statement should not be considered final since the experiment is not complete.

Jan 1, 1983

By Syd Peng

"As the International Conference on Ground Control in Mining (ICGCM) enters its 35th year in 2015, it is time to look back and identify the areas that need to be emphasized and to look forward to see what areas need to be researched in the future. In the past three decades, ground control has made a tremendous advancement, and many case studies published in the 36 volumes of proceedings have demonstrated its important role in the daily mining operations. However, there is still plenty of room for improvements. This paper discusses the research needs in 12 subject areas, including mine geology, rock property, zones of disturbance in overburden, computer modeling, underground stress measurements, research method, roof bolting, coal pillars, failures, subsidence, shield supports, and coal bumps.INTRODUCTIONThe International Conference on Ground Control in Mining (ICGCM) was founded in 1981. Since then, 1,546 papers have been published in the 36 conference proceedings, including the three surface subsidence workshops held in the 1981, 1986, and 1992. All types of topical areas regarding mining, from geotechnical core loggings in the exploration phase through backfilling after mining to finally spoil piles stability on the surface, have been addressed. A review of these papers, and other related literature as well, indicate that ground control has developed to become an inseparable part of mine design and a problem-solving tool for safe production.After 34 years, it is time to look back and identify the areas that need to be emphasized and to look forward to see what areas need to be researched in the future. There is no doubt that the conference series has achieved the goal for which it was originally designed: to provide an annual forum for the exchange of information among the researchers, government regulators, equipment manufacturers, consultants, service providers, and—above all—mine operators. There have been many papers addressing the application of ground control techniques for successful mine design and safe production, and, without these papers, many projects would have failed. In fact, the conference emphasis on application types of papers may have steered too far toward the application side. A review of the conference papers shows that papers have been leaning mostly toward the applied side, leaving most, if not all, fundamental issues behind in nearly every topical area. This paper addresses research needs in 12 topical areas: mine geology, rock property, zones of disturbance in overburden, computer modeling, underground stress measurements, research method, roof bolting, coal pillars, failures, subsidence, shield supports, and coal bumps."

Jan 1, 2015

By F. A. Forward, A. H. Ross, J. Halpern

Application of the carbonate leaching process to carno-tite ores has often been limited by the difficulty of obtaining simultaneous high recoveries of uranium and vanadium. The chemical aspects of this problem are discussed and the effect of prior roasting procedures on this discovery is described. IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to ±15°C. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO8 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi 02. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1959

By Philip A. Dirige

This paper presents the variability of responses of paste backfill specimens that have been prepared with varying binding agent and binder combinations, when subjected to uniaxial compressive strength testing. A testing program conducted for an underground operating mine to produce cost efficient paste fill recipes using four different binding agents, in various ratios and combinations, is presented to illustrate the responses. These binding agents are Normal Portland Cement Type-10 (NPC T-10), oxidation or sulphide attack resistant binder (Binder A), replacement binder B (Binder B), and replacement binder C (Binder C). The paste fill recipes were prepared at 2, 3.5 and 5% binder content at varying binder combinations, at fixed size and tested in a Material Testing System (MTS) under constant strain rate conditions following cure times of 7, 14, 28, 56, 90, 112, 180 and 240 days. The results of tests suggested that the strength data clearly shows a trend of increasing strength with increasing binder content but not necessarily cure time. It is noted that all the blends achieved dramatic increases in strength up to 28 days of cure and then either increased or decreased moderately beyond 28 days curing, depending on the binder content and binder combination. The moderate decrease is apparent for the 2% paste fill blends and in some binder combinations of the 3.5 and 5% blends, which indicated lackluster performance beyond 28 days curing. This lackluster strength performance indicated that the binder content and combination may not be sufficient for the paste fill to achieve complete hydration and acquire adequate strength performance beyond 28 days. This study indicated that economic paste fill recipes can be designed with confidence using affordable alternative binders. However, it is noted that these alternate binders cannot be used as stand alone binders but should be used in combination with NPC to facilitate hydration of the paste fill.

May 1, 2006

By Wood W, Bell A

Brown coal production in Victoria's Latrobe Valley Region (Figure 1) continues to rise and currently stands at around 50 Mt per annum. With the exception of around 2 Mt used to produce some 700 Kt of brown coal briquettes, this coal is mined by the State Electricity Commission to fuel large thermal power stations with a total installed capacity of just over 5 000 Megawatts. The moisture content of the coal as mined typically exceeds 60 per cent, making Latrobe Valley coal a markedly low rank fuel. The lack of heating value is, however, compensated for through power station design and by the fact that ash yield is very low, usually within the range of one per cent to four per cent on a dry basis. This means that compared with most other coals, the burning of Latrobe Valley brown coal produces relatively small quantities of waste products and discharges a minimal level of pollutants into the atmosphere. Even so, the inherent quality of Latrobe Valley coal does vary significantly from one area to another (Gloe, 1991; Barton et al, 1992) both on a local and a regional scale. Such variations need to be recognised and understood in order to not only realise efficiency gains in existing power stations but to properly assess resource potential for future utilisation and the application of new technologies. The principal aim of this paper is not to describe coal quality variation in detail or to speculate on the nature of and reasons for such variation. Rather, it is to simply underscore that significant differences do occur and that this is clearly a factor which needs to be considered in any evaluation of Latrobe Valley brown coal as a resource for the future.

Jan 1, 1992

By M. Rudolph, A. D. Renno, H. Wu

In this study, synthetic pure cassiterite and cassiterite doped with Fe were successfully produced by sintering. Their crystal structure and chemical compositions are characterised by optical microscopy, X-ray powder diffraction (XRD) as well as scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS) based chemical composition analysis. The electrostatic behaviour of synthetic and natural cassiterite was studied by electrophoretic measurements. Their floatability was studied by microflotation with two types of anionic collectors. Results show that the cassiterite floatability with these collectors behaves differently and lead to two opposite results: Natural cassiterite (enriched with Fe) > undoped pure SnO2 by using sulfosuccinamate (Aerosol® 22) Undoped pure SnO2 > Fe3+ doped > natural cassiterite (enriched with Fe) by using styrene phosphonic acid (SPA). Keywords: Synthetic cassiterite, lattice impurities, flotation, zeta potential, Aerosol® 22, styrene phosphonic acid

Jan 1, 2020

By Caetano Nunes da Silva

A busca por competitividade despertou na ArcelorMittal Tubarão interesse em novas possibilidades de integração de operação e manutenção nas áreas fabris, sendo retratado nesse trabalho a experiência da área de acabamento de bobinas. O trabalho enfoca: 1. a mudança cultural - que vem sendo continuamente trabalhada com as equipes e tem reforçado princípios como o senso de propriedade, autonomia e integração; 2. o incentivo ao intercâmbio entre funções - contribuindo para que as atividades da operação e manutenção fossem conhecidas por todos; 3. alterações na rotina, com a introdução de reuniões, inspeções e relatórios compartilhados - para melhor troca de informações entre as equipes de operação e manutenção; 4. mudança na localização física das equipes - com a acomodação das equipes de operação e manutenção mais próximas entre si e dos equipamentos; e por fim, 5. a implantação da manutenção autônoma - com a capacitação e realização de intervenções de manutenção pelos operadores. Com a melhoria da integração têm sido obtidos resultados expressivos de segurança, estabilidade operacional e custo.

Aug 7, 2018

By K. J. Oliver, A. G. Meyers, S. P. Hunt

Deformation Rate Analysis (DRA) and porosimetry have been used to demonstrate the “stress memory” effect in rock and to estimate the vertical in-situ stress in samples of fine-coarse grained sandstone and carbonaceous mudstone. The results of this study indicate that the stresses predicted using both methods are similar to those determined from depth and density of the overburden rocks. The results confirmed that DRA was still applicable even when the core had been sampled 18 months prior to testing. Additionally, the DRA results were modelled using the software PFC2D. A uniaxial test was modelled using the same rock parameters as those observed for the actual core samples. This numerical technique can be used as an aid for DRA results analysis, and can also be used to predict the minimum stress level at which the DRA technique is applicable. The results confirm that any rock mechanics laboratory having standard test equipment could apply the DRA method combined with standard UCS testwork to determine the in-situ stress. Mit der Analyse der Deformationsrate (DRA) und der Anwendung der Porosimetrie wird der Spannungsgedaechtnisseffekts (Stress Memory Effect) im Fels demonstriert, und es werden Abschaetzungen fuer die vertikale in-situ Spannung einer Probe aus mittelgrobem Sandstein und carbonierten Lehmstein getroffen. Die Ergebnisse dieser Untersuchung zeigen, dass die mit Hilfe dieser beiden Methoden ermittelten Spannungen sind vergleichbar. Die Ergebnisse bestaetigen, dass DRA noch anwendbar ist, wenn die Proben schon 18 Monate vor Untersuchungsbeginn gesammelt worden sind. Darueber hinaus wurden die DRA Ergebnisse mit Hilfe des Sofwarepakets PFC modelliert. Ein einaxialer Test wurde mit genau die gleichen Felsparametern, die fuer die eigentliche Probe gelten, modelliert. Diese numerische Methode kann sowohl als eine Unterstuetzung fuer DRA Ergebnisanalyse als auch zur Ermittlung der minimalen Spannung, bei dem die DRA Methode noch anwendbar ist, herangezogen werden. Die Ergebnisse bestaetigen, dass jedes Felsmechaniklabor, das mit den ueblichen Testgeraeten ausgestattet ist, die DRA Methode in Kombination mit dem Standard UCS Testarbeit zur Bestimmung der in-situ Spannungen anwenden kann. L'Analyse du Taux de la difformité (DRA) et les porosimetry ont été utilisés démontrer le " effet de la mémoire " du stress dans roc et estimer le stress dans - situ vertical dans échantillons de grès du grained fin grossier et mudstone carbonifère. Les résultats de cette étude indiquent que les insistances ont prédit utiliser les deux methods est semblable à ceux déterminés de profondeur et densité du surchargez des rocs. Les résultats ont confirmé ce DRA était encore même applicable quand le coeur avait été goûté 18 mois avant tester. En outre, les résultats DRA étaient des modelled qui utilisent le logiciel PFC2D. Une épreuve de l'uniaxial était modelled qui utilise les mêmes paramètres du roc comme ceux observé pour les réels échantillons du coeur. Cette technique numérique peut être utilisée comme une aide pour DRA résulte analyse, et peut aussi être utilisé pour prédire le niveau du stress minimum à que la technique DRA est applicable. Les résultats confirment que tout laboratoire des mécaniques du roc qui a le matériel de l'épreuve standard pourrait appliquer la méthode DRA combinée avec testwork UCS standard pour déterminer le stress dans - situ.

Jan 1, 2003

THE furnace described in this paper was installed and has been used by the writer for the melting of rich gold-bearing material, and has given complete satisfaction. It may, therefore, prove of interest to other metallurgists who are faced with a similarproblem. A furnace of this type should be most suitable for the reduction of "cyanide preeipitate," "charcoal ash," "anode sludge," &c. formerly the melting was done in fire-clay crucibles, using coke or crude oil as fuel, but this method is costly, slow, and unsatisfactory. A small water-jacketed blastfurnace was also tried on this material after briquetting it, but was discarded in favour of the electric furnace. The furnace may be described as a simple form of the Heroult resistance furnace, with an adjustable upper electrode and a fixed bottom electrode. This is in accordanee with Stansfield's classification of electric furnaces. The heating is mostly due to the resistance offered the current by the molten slag. The melting chamber consists of a steel drum 14 in. in diameter and 21 in. high, and is lined with silica bricks specially made to fit the shell. The internal diameter is G in. The bricks contain 92 % silica, are made from calcined quartzite bonded with fireclay, and are similar in composition to those used for lining steel converters. They are set in a mixture of finely-ground quartzite and clay, and well dried out. The shell is bolted to a steel plate, which forms the decking of a truck running on rails, so that the furnace can be moved under ahood for carrying off the fumes. A cast-iron slag spout is bolted to the shell below the tapping hole, which is 4 in. from the bottom of the shell. Opposite this another hole 1 in. in diameter is drilled through the shell and lining for the passage of the lower...

Jan 1, 1918

By S. N. Lekakh

Phosphorous segregated at grain boundaries during solidification and heat treatment dramatically decreases low temperature toughness of precipitation hardened Fe-Mn-Al-C austenitic steel. A thermodynamic analysis was performed to evaluate the possibility of decreasing P and subsequent segregation by Ca- and Ce-additives in the melt. It was shown that the predicted probability of forming a P containing compounds depends on melt composition and treatment sequence. Experimental heats were performed and several micro- and macro-structural effects of Ca- and Ce-additives were recognized by using an automated inclusion analysis technique.

Jan 1, 2010

By W. Carter, P. Chaubal, K. Spaleck, M. Schoeman, J. Bobek, W. Seegers

Keywords: Pyrometallurgy, steel, hearth, blast furnace The Mittal Steel Company operates about 36 blast furnaces on four continents. Furnaces range from 1100 m3 to 4800 m3 inner volume. The focus of the group is to push for increasing productivity and increasing campaign life. This has been especially challenging, as many of these furnaces were not equipped for long campaigns during their prior rebuilds. Monitoring and operating practices have to be modified to match the new philosophy. Mid-campaign hearth repair strategies and hearth design philosophies have had to be reconsidered. The paper describes experiences with the current hearth designs and measures taken for hearth life extension. Additionally, the philosophy of recent hearth re-designs is discussed.

Jan 1, 2006

This paper reviews the current techniques employed in the prediction of subsidence and how they have been applied to partial extraction systems. The method using influence functions to describe the shape of the profile is investigated in detail and has been adopted to model the subsidence over workings in Huntly. It is compared with the profile methods developed in the United Kingdom and found to predict the subsidence profile more accurately than these methods.

Jan 1, 1991

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of fluorspar (CaF2) from 36 U.S. and 50 foreign mires and deposits in 13 countries. Only 6 U.S. properties are considered to be economic, as 29 domestic deposits were found to have an average total cost of production that was uneconomical at a breakeven (0-pct) discounted-cash-flow rate of return (DCFROR). The 50 foreign properties evaluated represent at least 55 pot of demonstrated fluorspar resources located in market economy countries and China. Al I evaluated foreign operations were found to be economic to marginally economic in January 1984 dollars when compared against published prices for each country. Reserves for 56 properties totaled 97 million metric tons (mt) (recoverable Ca F,) from demonstrated ore resources of 344 million mt that contained 123 million mt CaF2. The average total cost needed to cover all costs over the life of each operation was determined for all recoverable fluorspar products. Comparisons of ruining, beneficiation, and transportation costs per metric ton of fluorspar concentrate illustrate advantages between countries. Of the three countries with the greatest fluorspar production, China, with its high-grade, low-cost operations had the lowest weighted-average total cost of production ($38/mt concentrate), Mexico was next, at $54/mt concentrate, and benefited in U. S. dollar terms from the devaluation of the peso. The Republic of South Africa needed an average of $90/mt of concentrate to cover all costs of production at its large low-grade deposits.

Jan 1, 1985

By D. Grobbelaar, A. Cichowicz, D. J. Birch

The Q-coda method for estimating the quality factor Q(f)= Qo(f)n was used to characterize seismic wave attenuation in a region of the Kaapvaal Craton that includes the mining areas of the Bushveld Complex and Witwatersrand Basin. Seismic waveform data, collected by locally distant stations of the South African National Seismograph Network (SANSN), consisted of mining-related events with magnitudes ranging from ML 1.8 to ML 4. Q was calculated for nine different source-receiver pairs spanning the study region. A weighted average Q based on the number of available data gave an estimated attenuation relation for the study region of Q(f) = 327 f 0.81.

Jan 1, 2015

Two structurally and mineralogically distinct sulphiderich veins cross-cutting the disseminated sulphides of the Nairne Pyrite Member appear to be products of local remobilization of sulphides under fracture-induced free energy gradients during regional metamorphism and tectonic deformation.The contrasting mineralogy of the two vein types may have arisen as a result of differences in the structural orientation of the veins and!or the relative ages of the veins.

Jan 1, 1969

By Dave Capstick, Ken Garner, Jim Porter

Technologies and systems used in the management of energy consumption in the mining and metal processing industry are well understood and documented from the supply side of the business. It is our contention that in many instances, through a more complete understanding of the demand side of the business, based on the detail of the operations plan, will provide greater lead time in terms of the design, implementation and utilisation of power supply infrastructure. Thus, optimal management of demand in a proactive manner, based on production requirements, will ensure both security of supply as well as continuity of operations. This paper describes the technology and methodology that is being developed to enable the above statement to be achieved. We use a case study to demonstrate the ability of the tools and methodology and conclude by outlining the business benefits achievable as well as the future developments emanating from this initiative.

Jan 1, 2005

By Ramin Motamed, Joseph A. W. Toth

Evaluation of the capacity of large-diameter drilled shafts using current load test methods present challenges when considering the magnitude of loads required to fully mobilize their capacities. Often, these full scale tests do not fully mobilize the capacity through side resistance. Therefore, the need for innovative solutions to extrapolate side resistance and interpret nominal capacity are of key interest. In this study, we evaluate three methodologies for extrapolating unit side resistance based on bi-directional load test data. Fellenius (2001) presented these methods for interpretation of pile capacity using static load tests. Our interpretations are based on the evaluation of 116 load tests. Unit side resistance was calculated and reviewed for each load test and categorized using three criteria of mobilization; (A) full, (B) partial and (C) linear. This study specifically focuses on load tests that showed fully mobilized unit side resistance behavior (Criteria A). The three methodologies were applied assuming Criteria (A) load tests were mobilized to 50% of their measured values. Subsequent comparisons of each extrapolation were then compared against the full measured values for each test and generally showed good agreement. INTRODUCTION It is widely accepted that conducting load tests such as standard top-down tests or bi-directional (i.e. O- cell) tests can help designers understand load-settlement behavior and the nominal resistance of drilled shaft foundations. These load testing methods provide the advantage of confirming design assumptions as well as improving the reliability of the foundation design. The potential cost savings from the application of these methods for mid to large size projects is self-evident. For example, in a recent project in Northern Nevada, an O-cell test on a 6.9 ft diameter, 114.8 ft length drilled shaft imposed an initial cost of $125k to the project, resulting in a 15% reduction on the total foundation cost; equivalent to $1.3 million in overall savings (Pease, 2014). However, the costs of implementing such methods on smaller projects can be prohibitively expensive (Hagerty et al, 2016). Despite the clear advantages of drilled shaft load testing, the current practice is not without limitations. Performing load tests on large-diameter drilled shafts with high capacities is a challenge considering the significant loads required to fully mobilize the capacity of such foundations. In some cases, the feasibility of these tests is impractical because the associated initial cost is not guaranteed to outweigh the final savings. As a result, large scale load tests are sometimes ruled out from the design phase of projects. Furthermore, in the majority of load tests the magnitude of loads applied are specifically selected to not approach failure, so the shafts can be used in the future foundation system (i.e. production shafts). This practice of field testing restricts our knowledge of the true capacity of the drilled shaft at failure; hence the nominal resistance remains unknown.

Jan 1, 2018

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock that is formed by the consolidation of clay, mud or silt. Production About 150 companies produced common clay and shale in 41 states. In states not reporting production, common clay and shale probably was mined and sold for construction applications by companies not participating in the U.S. Geological Survey (USGS) canvass of producers. Domestic production in 2005 was estimated to be 24.8 Mt (27.3 million st) valued at $176 million. This was based on a preliminary survey of the common clay and shale industry. The leading producer states, in decreasing order by tonnage, were North Carolina, Texas, Alabama, Georgia and Ohio.

Jan 1, 2006

By Jean J. Tancous

Chromium recovery from wet-blue offal trimmings and shavings can be done with substantial chemical cost gains by incineration at 600° C for 5 hr. Pretreating the offal with 0.5 M Na2C03 and air-drying prior to incineration produce Cr04 .By simply incinerating the offal, without pretreatment, an ash containing water insoluble Cr203 was produced. The Cr203 in the ash was purified by leaching with water. Chromium and crude protein were efficiently extracted from offal using 5 pct Na103, 5 pct H2S04, and 3 pct NaCl at 40° C. This procedure was effective but expensive. Satisfactory leather as to odor, appearance and shrinkage temperature was made from chromium recovered from wet-blue offal by incineration and by extraction. Chromium conservation is possible by recycling chromium liquors and by precipitating chromium from spent tanning liquors prior to combining these liquors with other tannery wastes. Combining chromium liquors with other wastes introduces contaminants that make chromium recovery and reuse difficult. Leaching sludges with H2SO4 produced marginal chemical cost gains. Leather tanned with these solutions had satisfactory shrinkage temperature but the sludge odors and iron contamination were objectionable.

Jan 1, 1979

By H. H. Schrenk

There is a need for a method of determining benzene vapor in air which is simple and accurate and suitable for making industrial hygiene surveys. The most widely used method in this country is the Smyth modification of the Elliott and Dalton procedure. This depends on the nitration of the benzene to m-dinitrobenzene, reduction to phenylenediamine with an excess of standard titanous chloride solution, and back titration with a standard ferric ammonium sulphate solution. This method has the disadvantages of being somewhat time-consuming and cumbersome; it requires considerable apparatus, and a special modification is necessary in the presence of toluene. Recently Cook and Ficklen have published a method based on the oxidation of benzene with hydrogen peroxide in the presence of iron salts. This method requires the use of solid carbon dioxide to freeze out the benzene. The reaction Which produces the color is complex; and only approximate quantitative estimations can be made, except in a very narrow range.

Jan 1, 1935