Search Documents

By Robert J. F. Goodfellow, William A. T. Meakin, Kevin Clarke, Eric Cole

INTRODUCTION New York City Water Supply—Background and History Since the 1840s New York City has been developing the largest, and perhaps, the best urban water supply and distribution system in the world in terms of quality and reliability. One of the engineering marvels of the modern world, the New York City water supply and distribution system serves a population of almost nine million, including residents in nearby Westchester, Putnam, Ulster, and Orange Counties of New York State. The average daily supplies presently are running at almost 60 m3/sec(about 1,350 million gallons per day). The watershed for the New York City water supply system, under the jurisdiction of the New York City Department of Environmental Protection (NYCDEP), consists of19 reservoirs and three controlled lakes, and covers an area of approximately5,000 square kilometers (about 2,000 square miles) north of New York City. The watershed total available storage capacity is about two billion cubic meters (560 billion gallons) and is divided into three reservoir systems: the Catskill and Delaware watersheds located West of the Hudson River; and the Croton watershed, located east of the Hudson River, see Figure 1. The first element of the system, the Croton Aqueduct, started operations in 1842.Through several updates and expansions, the present-day Croton system was in place by 1911, providing a potential maximum supply of about 15 m3/s (about 340 mgd). The system includes ten reservoirs and three controlled lakes. In the late 1800s, with the tremendous growth of the City, New York City water engineers began to look for additional sources. Between 1907 and 1929, the City acquired water rights and constructed a new 148 km (92 miles) Catskill aqueduct to convey water from the Ashokan Reservoir to the City. The Catskill system also included the construction of the Kensico and Hillview Reservoirs just north of the City,

Jan 1, 2005

By C. Özgen Karacan

Gob gas ventholes (GGV) are used to control methane inflows into a longwall operation by capturing it within the overlying fractured strata before it enters the work environment. Thus, it is important to understand the effects of various factors, such as drilling parameters, location of borehole, applied vacuum by exhausters and mining/panel parameters in order to be able to evaluate the performance of GGVs and to predict their effectiveness in controlling methane emissions. However, a practical model for this purpose currently does not exist. In this paper, we analyzed the total gas flow rates and methane percentages from 10 GGVs located on three adjacent panels operated in Pittsburgh coalbed in Southwestern Pennsylvania section of Northern Appalachian basin. The ventholes were drilled from different surface elevations and were located at varying distances from the start-up ends of the panels and from the tailgate entries. Exhauster pressures, casing diameters, location of longwall face and mining rates and production data were also recorded. These data were incorporated into a multilayer-perceptron (MLP) type artificial neural network (ANN) to model venthole production. The results showed that the two-hidden layer model predicted total production and the methane content of the GGVs with more than 90% accuracy. The ANN model was further used to conduct sensitivity analyses about the mean of the input variables to determine the effect of each input variable on the predicted production performance of GGVs.

Jan 1, 2009

A Robust Chemically Enhanced Electrostatic Separation Technology Physical separation processes such as gravity, magnetic and electrostatic separations are extensively used in heavy minerals separations. Electrostatic (aka High-Tension) separation facilitated by the conductivity differences, in particular, is used for separating rutile from zircon. Although electrostatic separation is effective, it is not efficient. It suffers from separation efficacy issues owing to sensitive variables such as humidity, surface contamination, particle sizes and the temperature of the feed and other equipment parameters. The variations in the process conditions especially with humidity, temperature of the feed and the mineralogy and surface impurities can cause significant reduction in the separation resulting in production rate losses and product quality issues. Cytec Industries has developed chemical enhancement technologies for electrostatic separation for rutile -zircon separation from the heavy minerals. The major advantage of our technology is its higher separation efficacy in the first pass, substantial energy savings and most importantly its ability to do separation at room temperatures. The bolt-on nature to the existing electrostatic also an added feature that reduces the capital expenditure significantly. The separation efficiency between rutile and zircon was increased as much as 8 - 11 per cent compared to control. It is possible to extend the chemical enhancer technology to problematic feeds and other mineral systems that are not easily amenable to conventional electrostatic separation.

Sep 13, 2010

By Paul C. Schmall, Arthur B. Corwin, Derek Maishman

Ground freezing occupies a unique and important niche in underground construction, fulfilling a geotechnical need that is difficult, or sometimes impossible, to fulfill through other groundwater control and excavation support methods. Where complete groundwater cut-off and in-built ground support are required, and deep excavation is planned or the work occurs in difficult or disturbed ground, ground freezing offers the assurance critical to safe and timely construction. Compared with other groundwater cut-off or excavation support methods, a frozen wall is easily connected to underlying bedrock and will also adhere to adjoining subsurface installations or obstructions, if necessary, to provide a composite cutoff structure. Ground freezing is effective in all soil and ground conditions and has been used for emergency situations in disturbed, displaced or loose ground, where detailed soil characterization could not practically be performed.

Jan 1, 2005

By T. Imgrund, A. Bischoff, S. Spürk

"Specific conditions of underground coal mines at great depth, such as high temperatures, high rates of methane inflow and natural ventilation pressure provide considerable challenges for the reliable design of appropriate mine ventilation systems. For decades coal mining in Germany has coped with these extreme circumstances. Based on these experiences appropriate software tools for simulating mine ventilation networks have been developed and continuously enhanced. This paper examines differences in the simulation results and underlying calculation methods of two software solutions. The analysis is based on the comparison of FlowNetTM and VentSim DesignTM (Version 5.1) regarding the accurate prediction of fluid mechanical quantities and their validation with real measurements. A special focus lies on exceptional ventilation scenarios typical for deep coal mines, like gas inflows, fire events and buoyancy effects. The purpose of the comparison is the future utilization of the experiences gained during mining at up to 1,500 m depth for state of the art ventilation design. INTRODUCTION Ventilation is an essential component of mine operations—as providing fresh air to workplaces, diluting and removing explosive, toxic or asphyxiating pollutants and assuring sufficient climate conditions. On the other hand, the costs of ventilation contribute to a large extend to the overall operating costs of a mine, as the share in the energy consumption of a mine may be in the range of 25–50% (Belle, 2008). Accordingly, proper design of ventilation systems has been a task since early times. Consequently software for modelling of ventilation networks has been developed in order to improve efficiency and accuracy of calculations (Maleki, 2018). Compressible flow has not been considered by initial ventilation modelling software tools. In Germany, the consideration of changes in airflow density—depending on pressure and temperature—in the algorithms of ventilation simulation software has been started in 1974 by Duepre & Hofbauer. This development had been continued by the Pruefstelle fuer Grubenbewetterung (Test Centre for Mine Ventilation) and resulted in the release of a computer ventilation software named “Wetter”. The mine inspectorate of the German state of North Rhine-Westphalia, which supervises the major coal mining district in Germany, declared ventilation simulation based on compressible flow being “state of the art” in 1985 (Pollak, 1985). This pronouncement made allowance for assessing the consequences of underground fires and downtimes of main fans based on advanced software solutions."

Jan 1, 2019

By S. Vorberg, J. Preussner, B. Fischer, U. Glatzel, R. Völkl, M. Wenderoth

Pt-Al-X alloys have shown good mechanical properties and adequate oxidation resistance. Starting from a promising Pt-Al-Cr alloy, the influence of Ni additions was investigated. After ageing finely dispersed precipitates are observed. Nb, Ta, Ti and Re increase strength when added as partial substitute for Al. Minor additions of B increase creep resistance and rupture time remarkably, owing to strengthening of the grain boundaries. The evolution of the alloy development programme as well as selected properties of the multi-component Pt-base alloys are presented.

Jan 1, 2006

By K. G. Wheeland, J. E. Dutrizac, M. Wasserlauf, A. A. Condy

Numerous processes for the treatment of thiosalts in base metal milling effluents have been examined in the past decade. Flowsheets for thirteen processes are outlined, and cost estimates are presented for a base case of a 720 mi/h effluent flow containing 1400 mg/L thiosalts. The processes are ranked on the basis of Numerous processes for the treatment of thiosalts in base metal milling effluents have been examined in the past decade. Flowsheets for thirteen processes are outlined, and cost estimates are presented for a base case of a 720 mi/h effluent flow containing 1400 mg/L thiosalts. The processes are ranked on the basis of

Jan 1, 1988

By Harry D. Lewis

Gilsonite is a lustrous black material that can be easily crushed into a chocolate-colored powder. It is a solid but relatively soft, lightweight hydrocarbon that visually resembles the volcanic glass obsidian. It was once thought to be a type of coal, but because it is thermoplastic it melts rather than bums. Gilsonite is found in commercial quantities only in the Uinta Basin of eastern Utah and western Colorado, where it forms vertical, nearly parallel veins of varying depth, width, and length. Gilsonite from different veins has different properties, most notably variations in softening point and solubility. These differences result in its use in a variety of industrial applications. Gilsonite's earliest commercial uses were in varnishes, buggy paints, and beer vat linings. Eventually it came to be used in more than 160 products ranging from inks to explosives. It is exported from the United States to most industrialized countries throughout the world. Today, due to competition from synthetics and other hydrocarbon products, its use has narrowed to several specific industries. Although sold mostly as a commodity, current research is focused on applications for gilsonite as a value added product. Historical Overview The discovery of gold in California and the dawn of the mining era in Nevada, Colorado, and Utah around 1850 brought a wave of prospectors to the western United States. One of those pioneers, Samuel H. Gilson, is generally credited with a major role in the discovery of gilsonite. The material now known as gilsonite was discovered several times from the late 1860s through the mid-1880s. It was William P. Blake who, after receiving samples of the material, wrote a paper in 1885 describing "a new variety of asphaltum from the Uinta Mountains." He termed the material uintaite. Although Sam Gilson was not the first to discover the mineral, he was an-inventor who used gilsonite in products that he patented. It was his conviction that the substance was of great value, which caused some to refer to it as gilsonite. The term Gilsonite became the registered trademark of the American Gilsonite Co., and it continues to be in use today. When the first company was formed to mine this substance in 1886 it was named the Gilsonite Manufacturing Co. This firm acquired many gilsonite mining claims and marketed a varnish made from the material. It was the unusual properties of gilsonite varnish that attracted the attention of Adolphus Busch of the Anheuser-Busch Brewing Co. In 1889 Anheuser-Busch bought out Gilson's interests and formed the Gilson Asphaltum Co. Busch had been importing asphalt from Sicily for use in lining beer barrels and saw gilsonite as being more readily available and cheaper. Although gilsonite did not work well in this application, Busch did acquire a large number of mining claims in the Uinta Basin. In 1903 the parent firm of Gilson Asphaltum financed the building of an 85-km railroad from near Grand Junction, CO, to Dragon, UT, to haul gilsonite ore to market. Underground mining was initially centered near Dragon and then later at Bonanza, UT, as different veins were mined. The railway was abandoned in 1937 in favor of truck transportation. In 1938 Gilson Asphaltum changed its name to Barber Asphalt Co., the predecessor of Barber Oil Corp. In 1946 Barber Oil teamed with Standard Oil of California to form a partnership, American Gilsonite Co., which today has its operational headquarters at Bonanza, UT. Barber Oil investigated many new uses for gilsonite, including the making of petroleum derivatives such as gasoline. This work led to the construction of a 116-km pipeline to carry slurried gilsonite to a refinery in Colorado for the production of gasoline, fuel oil, and coke. Pipeline operations began in 1957 but stopped when the economics of competing with petroleum became unfavorable, and the refinery was sold in 1973. In 1981 Standard Oil (later Chevron) became the sole owner of American Gilsonite and remained so until 1991, when it sold its interest to Stratford Enterprises Co. of Tulsa, OK. The companies have since been merged and now operate under the name American Gilsonite Co. with headquarters in Salt Lake City, UT. American Gilsonite continues to be the world's largest miner and supplier of the mineral. The American Asphalt Association was formed in 1902 by former stockholders in Gilson Asphaltum. This company mined various gilsonite claims until it was dissolved in 1953 and its properties were sold to American Gilsonite and Gordon S. Ziegler and Associates. The Utah Gilsonite Co. was established in 1920 and mined several claims until 1952, when its holdings were sold to Gordon Ziegler. Several other gilsonite mining ventures have been pursued in Utah, although they were significantly smaller in scale than those described above. There are currently three companies which mine gilsonite resin in Utah. They are American Gilsonite Co., Ziegler Chemical & Mineral Corp., and Lexco.

Jan 1, 1994

By Andy Mille

The paper highlights development of tunneling methodology in the UK during the years 1990-2000 using the example of two major tunneling contracts where there solution of difficult tunneling problems during construction has benefited the industry as a whole. The paper deals with specific difficulties on two Contracts. The London Water Ring Main 80 kms (50 miles) long tunnel average internal diameter 2.54 m (9 ft4 in) and the Brighton Stormwater Tunnel 5.2 km (3.2 miles) long tunnel with an internal diameter of 6 m (19 ft 8 in). The results of human endeavour and technological innovations will demonstrate the giant strides made in tunneling methodology in the last decade of the 20th Century.

Jan 1, 2001

By D. F. Malan

This study reviews the concept of squeezing (large time-dependent deformation) in rock and investigates the possibility of this phenomenon becoming more pronounced in the planned ultra-deep mines of the South African gold mining industry. Although squeezing behaviour is not commonly found at the current depths of the gold mining industry, it is observed at Hartebeestfontein Mine due to a combination of weak rock and high stresses. Calculations based on the average strength of the Witwatersrand quartzites and the competency factor used to identify squeezing conditions in civil engineering tunnels, indicate that there is an increased risk of squeezing behaviour in ultra-deep mines. This will adversely affect the profitability of these mines and highlights the need for further research into the time-dependent behaviour of rock. Finally, the current support strategies in squeezing conditions are reviewed.

Jan 1, 1998

By Ken Dyck, Chuck Edwards

"Cameco's McArthur River is the world's largest high grade uranium mine. Production started in late 1999. Cameco carried out the engineering design and construction management for the McArthur River project, including all aspects of mining, ore handling and ore transportation. The ore composition was expected to vary dramatically (0 to 30% U3O8; 0 to 25% clay; etc). To cope with the composition swings, sizing screens were selected to provide classification in the grinding circuit. The grinding circuit started up close to the design to provide minus 500 micron slurry. The 50% solids (wt) ground ore slurry proved to be difficult to transport to and process at the Key Lake Mill. Slurry containing high concentrations of high density pitchblende (about spgr 8.0) and low concentration of stabilizing clays, would settle in containers. Ore transport efficiency to Key Lake was found to be unacceptable.A test classification cyclone was installed in the grinding circuit at McArthur River early in 2002. The cyclone operating parameters were not typical, but the cyclone was made to work very successfully. Transportation efficiency to Key Lake increased due to more stable slurry. Preferentially ground (fine) pitchblende particles were easier to leach at Key Lake. The radiation exposure for operators and maintenance personnel to handle the more stable slurry was also reduced.The classification sizing screens were removed from the McArthur River grinding circuit and replaced by permanent classification cyclones late in 2002.INTRODUCTIONThe McArthur River mine and Key Lake mill operations are located in northern Saskatchewan, approximately 650 and 720 kilometres from Saskatoon, respectively. Figure 1 is a location map. McArthur River is the world's largest, high-grade uranium mine, with a production capacity of 18.7 million pounds U3O8 annually. (Rosner and Edwards 1998, Dyck 2000, Jamrozek 2000, Rodgers 2001) Proven and probable reserves are more than 473 million pounds U3O8. McArthur River ore, grading on average 21% U3O8, is milled at Cameco's Key Lake operation, 80 kilometres southwest by road. McArthur River production began in December 1999."

Jan 1, 2004

By R. L. Guerguerian

Nowadays, most grinding mills driven by a wrap-around ring motor are operating successfully. Some of the earlier problems could be attributed to the lateral stiffness and stability of their bearings. As a result, modifications to the bearings included the rearrangement of the shoes, or the addition of more shoes, closer to the horizontal centerline. This technical paper reports a study of the effects of bearings on the lateral stiffness of grinding mills driven by a wrap-around ring motor. The discussions cover the design of the four shoe trunnion bearings and examine the effects of the angular location of the shoes.

Jan 1, 2000

By F. P. Hassani, H. B. Poorooshasb

"A kinematically admissible velocity field is applied to study the arching phenomenon in a cohesionless granular backfill placed between two rough vertical inflexible walls. The study is different from the previous works which are almost entirely based on statically admissible stress fields. It is shown that the development of arches is strongly influenced by the previous loading history of the backfill which controls the nature of the constitutive laws that govern the mode of stress deformation of the backfill. This preliminary study employs simple models in order to show the potential use of such an approach in evaluating and understanding mine backfill behaviour in the underground excavation. The pressure exerted on the floor supporting the backfill is also studied in some detail.INTRODUCTIONAlthough the importance of the design of mine backfill has been discussed extensively by a number of authors, i.e. Hassani et al. (1985), such theories have not as yet been incorporated in design criteria for underground mine backfilling operation . One factor that such theories must incorporate is the so-called arching action .The phenomenon of arching has been the subject of study by many researchers in the field of civil engineering and mining engineering. Among these scholars the works of Terzaghi (1943), Krynine (1945), Lusher and Hoeg (1964) and Handy (1985) are noteworthy. All these authors use a statically admissible stress field as a starting point to develop their theories. The approach taken by the authors of the present paper is completely different because they employ a kinematicallyadmissible velocity field. It is their belief that the arching phenomenon is closely linked to the interlocking of grains as manifested by the degree of dilatation of the granular mass when subjected to a shearing process.This paper is written in the following sequence. To define the interlocking quantitatively it is necessary to state the constitutive law governing the stress deformation characateristics of the granular mass. This is done in the next section as the law proposed by Poorooshasb and Pietruszazck (1985, 1986) is stated and simplified to suit the present analysis. Next the mode of formation of an arch in a simple system consisting of a mass of backfill sandwiched between two vertical rough walls of infinite extent is examined. The velocity field obtained from the above example is used to obtain solutions to two more complicated situations. The first situation assumes that the backfill is supported, in addition to the vertical rough walls, by a Winkler foundation at its base. The second situation assumes that the Winkler foundation has been replaced by a horizontal beam of uniform section and simply supported at its extremities. The findings of the study are summarized and their practical implications discussed in the concluding remarks."

Jan 1, 1989

By Ewan Selers, Gary Cavanough

Drilling automation technology is well advanced and automated drill rigs are in use at a number of operating mines. This is not the case for the other drill and blast processes due to significant technical challenges to overcome. These challenges, with regard to the current “on bench” practices, include placing the initiators, loading the explosive and connecting up the initiation system. Although difficult, these challenges will be solved with engineering advances.

Jan 1, 2016

By Z. Mullard

The introduction of social media platforms has ushered in a new era of interaction and information exchange, which impact business-to-society relationships. Mining companies are closely watching these platforms, as the industry takes a cautious approach to control flows of information. This paper explores the risks, challenges and opportunities of using social media, based on a qualitative mixed methods investigation with stakeholders from the Canadian mining industry. Generational and language barriers, misunderstanding and limited motivation from regulators make implementing social media platforms challenging and risky at an organizational level. The benefits of social media include being able to mobilize communities and share information in real time. Despite the challenges, the study found that 62% of mining stakeholders are incorporating social media tools, mostly in an ad hoc manner. Flexible strategies for transparent communication and public engagement are creating new opportunities for information exchange.

Jan 1, 2011

By Mark DeSalvatore

Currently, at Caltrans, the Office of Structure Design is carrying out an extensive seismic retrofit program involving transportation structures throughout California. The goal of the retrofit program has been to upgrade existing transportation structures to meet the present seismic codes and anticipated loads that are generated during a seismic event Part of the retrofit program involves retrofitting existing structure foundations when required. To determine if the foundations of a specific structure need to be retrofitted, an engineering analysis of the existing foundations has to be done. If the engineering analysis of the structure foundations determines that the foundations will not meet the load carrying demands required by the structural engineer, the existing foundations are then retrofitted. The retrofit projects that require foundation modifications can be separated into two general cases. The first case comprises structures where the original designs will not meet the demands of the present seismic design code. In this case, the existing foundations are not capable of providing the load capacities the current seismic code requires. The second case consists of structures where the retrofitting of the superstructure will increase the required load carrying capacity of the existing foundations during a seismic event In this case, the anticipated load demands on the existing foundations are greater than the foundations are capable of providing. For either of the cases listed above, the present strategy for increasing the capacity of the existing structure foundation consists of installing tiedown anchors or large capacity piles to provide the required resistance to seisraically induced loads.

Jan 1, 1993

By Descour Jozef, Suguru Shirasagi, Takuji Yamamoto, Koji Murakami

For TBM tunneling no visual inspection of excavated ground is possible. This may hinder the high-speed excavation, particularly in complex ground conditions. The TBM Excavation Control System was developed for better prediction of geological conditions ahead of the tunnel face during excavation. The seismic reflector tracing produces volumetric images of anomalies in the ground in “near-real time.” These images are verified using logging data from pilot boring and TBM driving data, to improve reliability and precision of ground mapping. Also good correlation was obtained between the rock strength index computed from TBM data, and one derived from volumetric seismic images.

Jan 1, 2007

By G. M. Rao, P. N. Deo

Graphite is soft and easily floatable but it is quite difficult to obtain high purity concentrate at coarse sizes. Chemical treatment can produce high grade concentrate but it is an expensive process. Graphite containing plus 96% fixed carbon (FC) with coarse flakes commands high price in international market. Such graphite concentrate containing plus 96% FC was produced in Indian Bureau of Mines (IBM) by using newly developed reagent (mixture of different hydrocarbons and terpenes, IBM/D7) instead of commonly used frothers viz. pine oil, MIBC, kerosine etc. and regrinding in a special type of mill with special grinding media instead of grinding in a conventional ball/ rod mill followed by cleaning. Both the new reagent (frother) and special grinding media are inexpensive and readily available. The process is under patenting. This paper focuses application of this new grinding methodology for flake size protection, and the new reagent for selective flotation of high purity graphite.

Jan 1, 1995

By D. W. McDonald, L. M. Heaman, R. A. Creaser, T. Davies, T. Chacko, A. Simonetti

"The Three Bluffs gold deposit is located in the Committee Bay greenstone belt, which forms part of the Rae domain of the western Churchill province, Nunavut, Canada. Gold mineralization is hosted by iron formation of the Neoarchean volcanosedimentary Prince Albert Group, and is associated with silicification (quartz veining) and sulfidation of magnetite and other Fe-rich minerals. Conventional U-Pb zircon dating of a conformable dacite unit within the volcanosedimentary host-rock sequence and a crosscutting diorite intrusion confirm a ~2.7 Ga age for deposition of the supracrustal package. U-Pb monazite dates and Pb isotopic analyses of sulfides were obtained by laser ablation-multicollector-inductively coupled plasma-mass spectrometry (LA-MC-ICP-MS). A subset of U-Pb monazite (1813.8 ± 8.7 Ma) and Re-Os arsenopyrite (1822 ± 21 Ma) dates, combined with a Pb-Pb secondary errorchron age for pyrite and arsenopyrite (1829 ± 77 Ma), suggest that gold mineralization associated with sulfidation of the iron formation occurred at ~1815 Ma, prior to high-grade (upper amphibolite facies) tectonometamorphism in the Three Bluffs area (D2TB/(M2TB). An ~1815 Ma age for deposit formation is broadly consistent with evidence from elsewhere in the western Churchill province and to the southwest in Manitoba and Saskatchewan for a late Trans-Hudson (1.9-1.8 Ga) gold mineralizing event. The majority of U-Pb monazite ages form a second population at 1780.6 ± 4.2 Ma, similar to the age of the majority of Re-Os arsenopyrite analyses (1763 ± 11 Ma). These dates are thought to reflect the timing of peak M2TB metamorphism. 40Ar/39Ar dating of amphibole, biotite, and muscovite yielded plateau ages ranging from 1723.8 ± 9.0 Ma to 1710 ± 17 Ma, which are interpreted to record the timing of postpeak metamorphic cooling to below the respective closure temperatures for Ar diffusion in these minerals. Le gîte aurifère de Three Bluffs est situé dans la ceinture de roches vertes de Committee Bay, laquelle appartient au domaine de Rae dans l’ouest de la province de Churchill, au Nunavut, Canada. La minéralisation aurifère est encaissée par des formations de fer d’âge Néoarchéen appartenant aux roches volcanosédimentaire du Groupe de Prince Albert; la minéralisation est associée à de la silicification (veines de quartz) ainsi qu’à la sulfidation de la magnétite et d’autre minéraux riches en Fe.Les résultats de la géochronologie U-Pb conventionnelle sur une unité de dacite concordante au sein de la séquence volcanosédimentaire ainsi que d’une intrusion de diorite qui les recoupe indiquent que ces roches supracrustales ont un âge de ~2.7 Ga. Les âges U-Pb de la monazite ainsi que les analyses des isotopes du plomb des sulfures ont été obtenus par ablation laser (LA-MC-ICP-MS). Certains des âges U-Pb obtenus à partir de la monazite (1813.8 ± 8.7 Ma) et des âges Re-Os retournés par l’arsénopyrite (1822 ± 21 Ma), en association avec l’âge indiqué par une isochrone à données dispersées « errochron » secondaire Pb-Pb pour la pyrite et l’arsénopyrite (1829 ± 77 Ma), suggèrent que la minéralisation aurifère associée à la sulfidation de la formation de fer s’est formée vers ~1815 Ma, avant que l’événement tectonométamorphique (D2TB/(M2TB) de niveau élevé (faciès des amphibolites supérieures) affecte le secteur de Three Bluffs. Un âge de mise en place de ~1815 Ma pour ce gîte est compatible avec les données en provenance de l’ouest de la province de Churchill ainsi que plus au sud-ouest au Manitoba et en Saskatchewan qui indiquent la mise en place de minéralisations aurifères à la fin de l’orogénèse Trans-Hudsonienne (1.9-1.8 Ga).La majorité des âges U-Pb de la monazite constituent une seconde population formée à 1780.6 ± 4.2 Ma, ce qui est similaireLà l’âge obtenu pour la plupart des analyses Re-Os sur l’arsénopyrite (1763 ± 11 Ma). Ces âges reflètent probablement l’atteinte du pic métamorphique M2TB.La géochronologie 40Ar/39Ar de l’amphibole, de la bio"

Jan 1, 2009

The interaction between ore-bearing fluids and the siliciclastic rocks typically hosting orogenic gold deposits in Phanerozoic metamorphic terrains result in the development of a distinctive alteration halo. Along with petrological changes such as the replacement of chlorite by carbonate and the growth of sericite, characteristic geochemical modifications take place within this alteration envelope. These include variations in elemental abundances and more or less pronounced shifts in the H, C, N, O, and S isotopic signature of the ore system. æFingerprintingÆ these isotopic trends can provide exploration with additional vectors towards the ore zone, and yields valuable information regarding the source of the hydrothermal fluids and the solutes contained therein. Data from radiogenic isotope systems such as Sr-Rb, Ar-Ar, Xe-Ra, Pb-Pb, Re-Os, Sm-Nd, and U-Pb can constrain the kinematic history of ore-hosting structures, provide important clues concerning the absolute timing of gold emplacement, and enable the detailed characterisation of associated intrusives with respect to their magma source(s) and crystallisation age. Although high analytical costs, long turn-around times and the potential for misinterpretation prevent isotope systems from offering a æquick & dirtyÆ analytical method that would provide a significant advantage in exploration for orogenic gold mineralisation, the development of integrated four-dimensional ore genesis models depends heavily on constraints obtained from isotope mass spectrometry.

Jan 1, 2002