Search Documents

By Luo Yang

It has been known that after initial pile driving, pile capacity gain over time (set-up) could constitute a significant portion of the total pile capacity. In the past, there has been very little guidance for incorporating pile set-up capacity in design. This may be due to large uncertainties involved in predicting the pile set-up. A comprehensive statistical database is developed to describe the increase of pile axial capacity with time, known as set-up, when piles are driven into sand. Based on the collected pile testing data, pile set-up is significant and continues to develop for a long time after pile installation. The statistical database shows that a lognormal distribution can be used to describe the probabilistic characteristics of the predicted set-up capacity using Skov and Denver?s equation. The main objective of this paper is to incorporate the set-up effect into a reliability-based Load and Resistance Factor Design (LRFD) of driven piles in sand. A First Order Reliability Method (FORM) is used to derive separate resistance factors that would account for different degrees of uncertainties associated with the measured short-term capacity and the predicted set-up capacity from the proposed semi-empirical equations. The incorporation of set-up effects in the LRFD helps improve the prediction of the total capacity of driven piles, resulting in more economical design. A practical design procedure within LRFD framework to incorporate the pile set-up effect is outlined at the end of the paper.

Jan 1, 2006

By Reinhard Gnilsen

Soil Nail walls, like any other structure, must meet high standards of design to be acceptable to the public and owners. On the other hand, the concept of soil nailing trails behind other structures in terms of defined design criteria that are commonly acknowledged. This is not to say that soil nail walls need to be less safe or less conservative than alternative more conventional concepts. Instead, the lack of established design criteria and design methodology entails that rules of thumb from past experience, overly simplified calculation assumptions, and the engineers' common sense judgement must substitute for a complex analysis of true stability and wall performance. Those "design approaches" must be conservative to ensure an adequate structure. Also, soil nailing may not be perceived prudent where site conditions are considered beyond past experience. For instance, site conditions may be perceived out-side the scope of soil nailing applicability where walls are very high, soil parameters variable or low, or nearby buildings close to the wall edge. The latter relates in particular to deep

Jan 1, 1988

By Miguel Ángel Zúñiga Castillo

El presente texto señala la importancia del transporte minero como actividad en el sistema de costeo. En ese sentido, este se divide en transporte al interior de la mina y al exterior de ella. El primero implica que el mineral sea transportado in situ hasta la tolva de la planta de beneficio, donde no hay una etapa de transformación o concentración, mientras que el segundo traslada los concentrados hasta su destino final como son las fundiciones y refinerías en el mercado europeo, asiático y americano. Por ello, se busca seleccionar la mejor etapa de transporte que responda a las condiciones de las máquinas y equipos que trasladen el mineral desde el interior a la superficie de la mina. Así también se realiza un análisis macroeconómico de la importancia del flete en la actividad minera, originando un perfil de ahorro en la generación de divisas para el fortalecimiento del rol minero en el país.

Nov 24, 1986

By Roy C. Bartholomae

This Bureau of Mines report presents the results of a laboratory investigation of coal cutting mechanics and noise. These experiments were performed using linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts was ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to formulate analytical models of the coal cutting forces and noise. The analytical model for coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as provide benefits to other important areas of health and safety in underground mining.

Jan 1, 1983

By Gennaro G. Marino

The Bureau of Mines and the University of Illinois investigated surface characteristics and damage to structures from mine subsidence over a room-and-pillar coal mine in Hegeler, IL. Data on three adjacent subsidence sags and associated structural damage were collected, summarized and evaluated. The subsidence sags developed over a 10-year period and took place above a modified room-and-pillar operation mining the Herrin (No. 6) coal at a depth of 130 to 135 ft. Surface vertical displacements of 3.0 to 3.5 ft resulted from extracting 6.1 to 6.4 ft of coal. Ground movements associated with sag formation severely damaged three houses and a radio station building, broke numerous utility lines, and structurally distorted three radio transmission towers. The radio station was remodeled and the towers repaired, but the three houses were subsequently demolished. Surface waters collecting in the subsidence depressions caused failure of radial ground transmission systems. The following subsidence profile characteristics were determined at the radio station and one of the houses, respectively: profile slopes, 0.02 and 0.07; maximum curvatures, 2.3 x 10-4 ft-1 and 3.0 x 10-4 ft-1; and angular distortions, 6.6 x 10-3 and 62.0 x 10-3. Although the house was more severely damaged than the radio station, both structures are classified as severely to very severely damaged.

Jan 1, 1986

In 1976 the Pitjantjatjara Council was established under the Associations Incorporation Act 1985 (SA), for the initial purpose of organising and bringing together three similar Indigenous groups. These members of the Pitjantjatjara Council of Central Australia were demanding land rights and to legally protect their traditional lands. The Land Rights movement was more focused on the South Australian Government that became more receptive to the general notion that Aboriginal freehold land could be attainable.For almost five years, Pitjantjatjara CouncilÆs intense negotiations took place with the Dunstan and Tonkin Governments culminating in the final passage of legislation by 1981. A bi-partisan approach by Government and opposition applauded by all South Australians for its mature and socially responsible actions, in line with the Aboriginal Land Rights (Northern Territory) Act 1976 (Cth). Despite the similarities between South Australian and the Northern Territory Land Rights legislation, there still remains one obvious distinction. In the Northern Territory case, its legislation established æLand CouncilsÆ as statutory authorities that are responsible for the management and use of designated Aboriginal lands. On the other hand, South Australian legislation fails to include any reference to æLand CouncilsÆ as defined in the Northern Territory Act. The intention of establishing such æLand CouncilsÆ in the Northern Territory was, and is to provide legal, anthropological and other expect advisers that respond to the wishes and opinions of Traditional Aboriginal Owners. Negotiations between mining companies and Land Councils, will, after the granting of mining leases, monies are then transferred to those Councils being a percentage of royalty entitlements. While the Pitjantjatjara Land Rights Act 1981 (SA) (Act) does provide royalty arrangements to Anangu Pitjantjatjara (AP), a body corporate pursuant to the Act as a Landholding Body (and not as a æLand CouncilÆ), it does not provide any royalty payments for the legal and anthropological services by the Pitjantjatjara Council for providing essentially similar services as the Northern Territory Land Councils. The limited services by AP do provide complimentary services from other organisations û including the Pitjantjatjara Council. There are approximately 4000 Anangu members who reside on AP Lands and more than 1000 other Anangu members live near AP Lands in Western Australia and the Northern Territory. These people are defined as APÆs æTraditional OwnersÆ by virtue of their affiliation to portions of AP Lands. As a result, the depth and understanding of spiritual beliefs and customs are strongly present as it relates to the whole of the Lands. Most of these members reside at permanent communities that spread unevenly about the northern and south-western parts of AP Lands. In addition, there are numerous æHomelandsÆ where families and extended families have establish homes, with electricity and water supplies on those Traditional Lands (see Appendix 1 and 2 of this paper depicting the map showing AP Lands and also showing stunning photographs taken during late last year). All roads and airstrips are unsealed between communities and Homelands and the essential services to all communities are limited and costly to provide, and require continuous upgrading. Capital expenditure on infrastructure is sorely needed and alarming levels of unemployment is of serious concern. Tjilpi (older) Anangu members have continually discuss the urgency to provide employment and education for the future of their children and grandchildren while balancing the needs of maintaining cultural and spiritual considerations. It is thus a growing realisation by many Traditional Owners that long-term benefits occur as a result of exploration and production of oil or minerals. There are promising results from Primary Industry and Resources of South AustraliaÆs (PIRSA) Aero-magnetic Surveys on the Musgrave and Mann Ranges and soon to be completed surveys of the remaining southern half of AP Lands (see Appendix 3). PIRSA and mining companies û such as Rio Tinto Exploration Pty Ltd and Delta Gold NL û have been more conscious of the necessity for improving the dissemination of information to Traditional Owners and to AP members. With recent findings of large nickel deposits just over the border in Western Australia, there is a strong indication that discoveries may occur on AP Lands as similar geological information is present on the east Musgrave Block. Consequently there are concerted efforts by the legal and anthropological services of the Pitjantjatjara Council to arrange Workshops and Summit meeting to give extra information û particularly information concerning the true effect of large-scale mining operations û to members to properly consider these proposals. Pitjantjatjara Council will play a major role in any decisions effecting Traditional Owners and AP, and will ensure orderly and professional services when dealing with legal, cultural and sensitive matters. This paper addresses the historical and current relationship between Pitjantjatjara Council and AP, with an emphasis on mining operations on AP Lands. It argues that future economic and social development on AP Lands hinge predominantly on the legal recognition of the Pitjantjatjara Council for its ongoing role, responsibilities and protection afforded to AP and its Traditional Owners.

Jan 1, 2002

By Joseph H. Bilbrey

COBALT is a silvery gray metal which closely resembles nickel in appearance and properties although it is somewhat harder and more brittle. It is rather widely disseminated and is estimated to make up about 0.001 percent of the earth's crust as compared to 0.020 percent for nickel. Cobalt, one of the four ferromagnetic elements, is used for many magnetic applications. It is oxidation resistant, a property which when coupled with its moderately high melting point of 1,495° C., makes it useful in high-temperature applications. Although cobalt had been used by man as a coloring agent for glass and other ceramic products for 4,000 years, it was not isolated as a metal until 1742 and not established as an element until some 40 years later. Early in the 20th century, cobalt began to be used in alloys, and soon these applications displaced ceramics as the major consumer of cobalt. The use of cobalt in alloys gave considerable stimulus to production, and the world output of cobalt increased rapidly, rising from 400 tons in 1920 to 1,400 tons in 1930 and 5,500 tons in 1940. With the advent of the jet plane in the mid 1940's and the consequent increased need for cobalt-bearing high-temperature alloys, cobalt production again increased, reaching 7,900 tons in 1950. The increased demand for cobalt during the Korean war coupled with a large demand for stockpiling caused world production to more than double within the next 10 years, reaching a peak of 17,300 tons in 1959.

Jan 1, 1962

By Bruno Henrique Reis

O pó de aciaria elétrica (PAE) é um importante subproduto da indústria siderúrgica devido ao seu alto teor de Zn. Assim, tecnologias vêm sendo desenvolvidas visando seu aproveitamento, sendo o forno Waelz a mais difundida delas atualmente. Sua operação, por contar com um forno rotativo de grandes dimensões, que abriga uma infinidade de fenômenos físico-químicos, apresenta difícil previsibilidade ab initio. Por essa razão, este trabalho faz uso de uma ferramenta avançada da termodinâmica computacional, destinada à modelagem de processos, chamada SimuSage, a fim de modelar o seu comportamento. Para a criação do modelo utilizou-se também uma base de dados termodinâmicos advinda do software FactSage e a plataforma Lazarus. Com base em dados e resultados operacionais da literatura, foi possível realizar simulações no modo adiabático e comparar os resultados com os da prática industrial. Constatou-se uma grande sensibilidade do modelo com relação à quantidade de ar de entrada considerada no sistema, mas, também, boa aproximação dos resultados com relação à composição química dos produtos Óxido Waelz e Escória Waelz.

Aug 16, 2017

By David C. Yang

A packed column (or static tube) flotation system is an innovative technology which utilizes a controlled dispersion reagent scheme and a new machine. The unique aspect of the machine is its packed-bed design permitting an unlimited froth bed height with countercurrent water washing for effective processing of fine particles. In operation, the conditioned ore slurry is fed into the middle section of the column where separation processes begin. Air, introduced at the bottom of the packed column, contacts the hydrophobic particles and floats them off continuously as the feed is added, while the gangue sinks to the base of the column. The system functions efficiently because intimate particle-bubble contact is achieved by the packing design which has no moving parts and requires no ancillary air-bubble generator. Other attractive features of the packed column flotation include high throughput, low power requirements, and simple control. Results from laboratory and pilot plant tests of this system show remarkable improvements over current industrial practices on a wide variety of ores and coals.

Jan 1, 1988

By Gregory Yates

INTRODUCTION Project Description The Silver Line is a Bus Rapid Transit (BRT) Line and is Boston?s newest transit service. Silver Line Phase I extends along Washington Street entirely on the surface in priority bus lanes from Dudley Station in Roxbury through the South End and Chinatown neighborhoods to downtown Boston. The Phase I opened in July 2002. Silver Line Phase II consists of an underground transit tunnel from South Station to the South Boston Waterfront with underground stations at Courthouse and World Trade Center to Silver Line Way east of D Street. Phase II continues through the Ted Williams Tunnel to all the terminals at Logan Airport, and on the surface to the Boston Marine Industrial Park and City Point. Phase II opened in December 2004. Silver Line Phase III is a one mile tunnel connection to the existing Phase II tunnel in the vicinity of South Station and will eventually portal on Tremont Street just north of Marginal Road. After leaving the portal, the buses will use dedicated bus only lanes on the surface roadway network to connect to the Phase I service. Figure 1 shows the alignment of the Silver Line upon completion of the Phase III project.

By Robert T. MacMillan

A process has been developed in the laboratory and expanded to semi-pilot-plant scale for recovering titania, iron, and byproducts from two types of titaniferous iron ores. A reducing roast with coke and soda ash followed by grinding and magnetic separation produced powdered iron and slag from which titania and byproducts were recovered by H2SO4 decomposition. Based on the steps tested on a. semi-pilot-plant scale supplemented by the results of the laboratory investigations, enough data are available to make a balanced flow sheet. Combined data from the laboratory and semi-pilot plant indicated that 85 to 9O percent of the titania content of the ore was recoverable and that approximately 90 percent of the iron could be recovered as a metallic-iron powder. Tahawus magnetite from the Maclntyre mine at Tahawus, N. Y., was successfully treated as follows: (1) The ore was roasted at 1,050° to 1,080° C. with carbon and soda ash, thereby reducing the iron to metal sponge and retaining the titania in the slag. (2) The metallic iron was separated, after wet grinding, by magnetic or gravity means. (3) The slag fraction was air-roasted at 850° C. and leached with NaOH to recover Na3VO4. (4) The leached solids received a dilute-H2SO4 leach to remove interfering impurities, chiefly Na2O and SiO2. (5) Titania was dissolved from the leached solids of step (4) by a H2SO4-bake followed by a water leach. (6) Titania was precipitated by seeding and boiling the resulting solution. The spent liquor was used for the dilute-H2SO4 leach in step (4). The following scheme was found to be technically feasible for recovering other byproducts of the process. (1) The gelled filtrate from the dilute-acid leach step was washed and dehydrated to produce a commercially acceptable silica gel. (2) The wash liquor containing sulfates of Na2O, Al2O3, Fe2O3, and TiO2 was combined with the highly alkaline filtrate from the wet-grind and metallic iron-separation steps, precipitating iron and titanium hydroxides, which were separated for special treatment. (3) Anhydrous Na2SO4 and Al2O3?3H2O were recoverable from the alkaline filtrate from step (2) by evaporation and carbonation, respectively, and the barren liquor was recycled to the magnetic-separation step.

Jan 1, 1952

By H. J. Uananisa, M. J. Papo, C. W. Siyasiya, W. E. Stumpf

"SynopsisThe need to reduce weight while maintaining good mechanical properties in materials used in the automotive industry has over the years seen an increased exploitation of various steels to meet this new demand. In line with this development, the ferritic stainless steel family has seen a wide application in this industry, with the AISI 436 type increasingly being used for automotive trims and mufflers for exhaust systems, as well as a significant part of this steel’s application being for the manufacture of wheel nuts and wheel nut caps in trucks, mainly through the deep drawing process. However, there have been reports of some poor surface roughening of this material during deep drawing, with tearing and/or cracking also reported in some instances. This has been suspected to possibly be associated with some local differences in localized mechanical properties between grains and grain clusters of the rolled and annealed material.In order to investigate the poor surface roughness exhibited by AISI 436 ferritic stainless steel (FSS) during deep-drawing, Lankford values (R-mean and ?r), grain size, and microtextures of various sheet samples from this steel were studied. The chemical composition range for the samples was 0.013–0.017% C, 17–17.4% Cr, 0.9–1% Mo, and 0.4–0.5% Nb. The steels were subjected to various hot and cold rolling processing routes i.e. involving industrial direct rolling (DR) or intermediate annealing rolling (IR), and the drawability and final surface qualities of the steels were compared. It was found that the DR route gave an average R-mean and ?r value of 1.9 and -1.4 respectively, while the IR route yielded an average Rmean and ?r value of 1.6 and 0.52 respectively. The high ?r value for the DR processing route had a substantial adverse effect on the drawability. IR samples exhibited a smoother surface finish on visual inspection, while clear flow lines were visible on the DR samples, despite the fact that DR is the preferred industrial processing route due to the reduced production costs it offers. This observation was also confirmed through SEM examinations. The difference in the surface quality was attributed to microtexture. However, the mechanism responsible for this difference still needs to be identified."

Jan 1, 2015

By Richard A. Kesler, W. Michael Reed

Grindability or resistance to fine comminution is the fundamental issue involved in the application and sizing of grinding mills. Over the years, many theories for determining the amount of energy required for size reduction to a specified fineness have been proposed. The first published theory, introduced by P. R. von Rittinger in 1867, stated that the energy required for crushing or grinding is proportional to the increase in surface area produced. The surface area of a ton of particles of diameter (d) is proportional to (1/d), therefore the work input per ton for particles of diameter (d) would be proportional to (1/d). The second significant theory is that of F. Kick published in 1885. Kick said that the work required is proportional to the reduction in volume of the particles concerned. If (f) is the diameter of the feed particles and (p) is the diameter of the product particles, the work input relationship would be: [W =Ioq(f/p) 9] The "Third Theory" of F.C. Bond, introduced in 1951, states that the work required is proportional to the length of the new crack tips produced in particle breakage during crushing or grinding and equals work represented by the product minus that represented by the feed. This takes the form: [W=]

Jan 1, 1982

Protect mine rescuers from heat-induced stress that drastically cuts their endurance and saps their strength. Approach To prevent exhaustion caused by thermal stress, a rescuer can wear a liquid-cooled hood and vest which absorbs heat, thereby reducing the heat-induced strain on the rescuer's heart and circulatory system. How It Works Liquid coolant is continuously circulated through a self-contained system in which the coolant is chilled by a heat sink on the wearer's belt. The coolant, which is a mixture of alcohol and water, is pumped from the heat sink to bladders inside the hood and vest where it absorbs body heat. After absorbing heat In the hood and vest areas, the coolant returns to the heat sink where it is rechilled by passing through a tube coiled around a steel can containing a block of ice. To adjust the temperature of coolant leaving the heat sink unit, a valve can be operated by the wearer, causing part of the flow to bypass the coil. A small pump and a rechargeable battery are also part of the assembly.

Jan 1, 1979

By S. Deonarain, L. S. Schultz

"This paper details the process and methodology followed to rehabilitate a rectangular ventilation shaft, situated in the Free State region of the Witwatersrand Gold Fields in South Africa. The shaft consists of seven compartments where self-mining of the sidewalls had taken place and damage to the decayed steel work in the shaft had taken place, thus limiting access down the shaft. The paper will provide some insight into the successes and challenges encountered during the project and may provide some learnings for future projects of a similar nature. INTRODUCTION The ventilation shaft forms part of the Phakisa Mine, situated in the Welkom area of the Free State province of South Africa, and is located in the Southern part of the Witwatersrand Basin, one of the world’s largest known and richest gold deposits (Figure 1).As is typical in South African gold mines situated in the Witwatersrand basin, the shaft is 1 770 metres deep (below collar). The shaft was sunk during the early 1940’s and comprised a rectangular shape with 7 compartments, used for both rock hoisting and men and material winding, respectively, with a single lift “Mary-Anne” compartment. Early in 2003, the mine decided to change the shaft from a downcast hoisting shaft to an up-cast ventilation shaft. The conveyances, ropes, winders and headgear (head frame) were removed and replaced with a high volume fan delivering 323m³/s of air at a pressure of 4.2Pa on surface. The up-cast velocity in the shaft was 6.5m/s, however this reduced significantly with the scaling of the shaft and the restrictions at shaft bottom. Although Harmony had converted the shaft from a downcast service shaft to an up-cast ventilation shaft some years back, the shaft steel work in the barrel of the shaft was left intact. Over the years, the steelwork in the shaft had decayed (rust and grime) and portions of this steelwork fell down the shaft. Concurrent with the decaying steel work, portions of the shaft lining had collapsed and it was getting progressively worse."

Jan 1, 2019

By John Redstone, André R. Laplante

"Le rebroyage des concentrés d'hématite en usine (Sidbec-Normines, Port-Cartier) et en laboratoire a été modélisé selon le modèle de Reid (1965).L'effet du pourcentage solide sur la cinétique de broyage a été étudié en usine. La fonction de sélection corrigée (pour tenir compte de l'effet du pourcentage solide sur le temps de rétention) augmente lorsque le pourcentage solide augmente de 80 à 84 pourcent. Cette amélioration est contrebalancée par une augmentation de la quantité de pulpe court-circuitée, à des pourcentages solides supérieurs a 81%. La densité optimum de broyage se situe à 84 pourcent.Comme alternative au mode d'opération actuel, l'assemblage des broyeurs en série plutôt qu'en parallèle a également été simulée. Le moins 44 µm passe alors de 68.1 à 72.5 pourcent, ce qui correspond à une capacité supplémentaire de 32 tonnes à l'heure par broyeur. Ces résultats doivent toutefois être interprétés avec prudence, car la cinétique de broyage n'est généralement pas linéaire lorsque le taux d'alimentation est plus que doublé.IntroductionL'usine de bouletage de Sidbec-Normines Inc. a été décrite par Morimoto (1977), Lévesque et al. (1979) et Pabst (1979). La section de broyage des concentrés contient six broyeurs à boulets en parallèle et en circuit ouvert, d'un diamètre de 5. 18 mètres et de 10.36 mètres de longueur. Ils contiennent chacun environ 350 tonnes de boulets d'acier forgé de 3.8 cm de diamètre. Le concentré est broyé de 10 pourcent moins 150 µm (100 mailles) à 65-68 pourcent moins 44 µm (325 mailles), à un pourcentage solide de 78 à 80 pourcent. Cette fragmentation poussée exige une consommation d'énergie de 32 kWh/tonne. Cette énergie est surtout libérée sous forme de chaleur, la pulpe étant déchargée a une température de 68-72° C. II en résulte un milieu de broyage corrosif, et une consommation de boulets élevée, de 3.4 à 4.0 kg / tonne broyée."

Jan 1, 1983

By Forrest T. Moyer

Injury experience at coal mines and mechanical-cleaning plants (excluding officeworkers ) in 1967 was 222 fatal and 10,115 nonfatal disabling work injuries during an exposure time of 241.8 million man-hours. These injuries occurred at a frequency rate of 42-75 per million man-hours worked; the severity rate was 7,699 days lost or charged per million man-hours. Each of these general measures of injury experience was lower than similar data recorded for 1966. Employment at 6,885 coal mines and 569 mechanical-cleaning plants, excluding officeworkers, averaged 139,312 men in 1967. The average number of days worked was 220. Coal production totaled 560.8 million short tons, at rates of 2.32 tons per man-hour and 18.32 tons per man-day. A total of 2,779 onsite officeworkers at coal mines and mechanical- cleaning plants worked 5.2 million man-hours in 1967 without a disabling work injury.

Jan 1, 1972

By John D. Spencer

Surveys to establish the quantity and quality of coals available for metallurgical, industrial, and energy use, investigations to develop better mining methods, and studies aimed at improving the health and safety of those who mine the coal highlighted Bureau of Mines research and technologic work on coal in 1968. Also being developed are more efficient methods of coal preparation, transportation, storage, and utilization. Supplementing this effort are projects designed to assure minimum disturbance of land, water, and air resources. Research centers and laboratories of the Bureau of Mines are listed in appendix A. Publications released during 1968 are cited with the various projects and in appendix C. Organizations that cooperated in the work in various ways are cited in appendix B.

Jan 1, 1969

By J. K. Whyatt, W. P. Blake, T. J. Williams

A study at the Idaho mine revealed that, despite the apparent randomness of seismic events, common characteristics defined five recurring types. These characteristics included the geological structure that slipped, the first-motion pattern and the location and intensity of damage. Many large events caused little or no damage, and where it did occur it was concentrated at intersections between slipping structures and mine openings. Of 39 events between 1989 and 1994 with local magnitudes of 2.5 or more, 10 were caused by slip on bedding planes in the southern limb of the mine, 6 occurred near the vein along a set of near-vertical faults that form the central shear zone, 8 were strike-slip events on the Southern Control Fault, 4 were by slip on the vein itself and 10 involved strike-slip and/or dip-slip movement along the North Control Fault. Strategies for control of mining-induced seismicity need to consider all five types of event, lest a strategy to reduce one type increases others

Jun 19, 1905

By E Portes, G Noble, J Roberto, A Stabile

Iron ore beneficiation plants are facing economic pressures to treat more challenging ore types, improve efficiency and improve product quality. Better control and stability of the plant process in the face of increasing feed ore variability has been a goal for many of the operations facing these challenges.Prompt gamma neutron activation analysis (PGNAA) technology has proven to be a successful measurement technique within an iron ore beneficiation plant. PGNAA was first developed in the early 1980s for the measurement of the elemental composition of bulk materials. Today, PGNAA technology is applied for elemental analysis within the iron ore industry on both bulk materials and slurries.Traditional composite sampling throughout the wet iron ore beneficiation process provides a delayed measurement of average properties but does not capture the true variability of the process in real-time. As such this is a limiting factor towards stabilisation and optimisation of the process. A PGNAA analyser provides real-time slurry elemental analysis of feed, concentrate and tails streams within the processing plant. The analytical data from the analyser can be exploited with a control strategy to correct and stabilise the plant on a much shorter time scale, delivering significant economic benefits and greater operational flexibility. The economic benefits include more stable product quality and a reduction in composite sampling and laboratory costs.Some example results will be presented from the Vale Vargem Grande iron ore beneficiation plants, which are utilising a six stream multiplexed Thermo Scientific PGNAA Slurry Analyser.CITATION:Noble, G, Stabile, A, Portes, E and Roberto, J, 2017. Real-time slurry elemental analyser for iron ore beneficiation plant control, in Proceedings Iron Ore 2017, pp 481–486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017